PIC17LC762-08I/PT - 8-Bit 16KB EPROM MCU, 66 I/O | Microchip
MPN: PIC17LC762-08I/PT ✗ Akhir HidupPIC17LC762-08I/PT Ringkasan
A microcontroller (MCU) is a single-chip computer containing a CPU, memory, and programmable I/O peripherals. The PIC17 family was Microchip's first architecture to use a 16-bit instruction word with an 8-bit data path (modified Harvard architecture) and is widely regarded as the precursor to the modern PIC18 and dsPIC families. Unlike the 12-bit and 14-bit core PIC16 parts, the PIC17 offers a richer instruction set of 58 single-word instructions, a single-cycle hardware multiplier, and a 121 ns instruction cycle at 33 MHz - making it suitable for control loops and signal processing tasks beyond what a baseline PIC16 can handle.
Key features include a 10-bit successive-approximation analog-to-digital converter (ADC) with up to 12 input channels, two 8-bit timers plus one 16-bit timer/counter, a USART with RS-485 support, an SSP module for SPI and I2C, a capture/compare/PWM (CCP) module, and 16K x 16 words of OTP program memory. The device also integrates a watchdog timer with its own on-chip RC oscillator for fail-safe operation.
Architecturally, the PIC17LC762 uses an enhanced 16-bit instruction pipeline, a hardware 8-bit x 8-bit multiplier that completes in one instruction cycle, and a 16-level deep hardware stack. The LC variant specifically supports low-voltage operation down to 2.5V, distinguishing it from the 5V-only PIC17C762. This part is now mature and remains useful for legacy industrial and embedded designs, though new designs typically use PIC18 or dsPIC33 parts.
Typical applications include industrial process control, motor control front-ends, instrumentation data acquisition, automotive body electronics (non-safety), legacy embedded systems, and sensor interfacing boards that require more I/O than a 28-pin PIC16 part can offer but do not need the complexity of a dsPIC. The wide 66-I/O count makes it a fit for human-machine interface (HMI) panels and large keypad/display matrices.
When designing with this device, note that OTP memory cannot be reprogrammed in-circuit. For development, use the windowed (JW) UV-erasable ceramic version, or migrate to the flash-based PIC18F family for new designs. The 80-pin TQFP requires a 4-layer PCB with proper thermal vias under the exposed pad for reliable operation above 25 MHz.
This page synthesizes distributor stock and pricing data, drop-in compatible same-package alternatives from the PIC17C/PIC17LC families, and practical design notes for the PIC17LC762 that are not collated on any single distributor page.
Alternatif penggantian untuk PIC17LC762-08I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC17LC762-08I/PT (sama faktor bentuk dan footprint) — berbeda di dalam Package, Core Architecture, Program Memory Type, Program Memory Size, Instruction Cycle Time.
PIC17LC762-08I/L
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17LC756A-08I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17LC752T-08I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17C762-16I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17C762-16/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17LC756AT-08I/L
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC17LC762-08I/PT Rating Maksimal & Karakteristik Listrik
| Product Family | PIC17 |
| Core Architecture | 8-bit RISC, 16-bit instruction word |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 16 KB (8K x 16 instructions) |
| RAM Size | 678 bytes |
| Number of I/O Pins | 66 |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Frekuensi Bawah Maximum | 33 MHz |
| Instruction Cycle Time | 121 ns (single cycle) |
| ADC | 10-bit, up to 12 channels |
| Timers | Two 8-bit + One 16-bit Timer/Counter |
| Serial Interfaces | USART (RS-485), SSP (SPI/I2C) |
| Paket | TQFP-80 (PT), 12x12 mm |
| Suhu Kerja | -40C to +85C (Industrial) |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
Konfigurasi Pin PIC17LC762-08I/PT
| Pin produk 1 | OSC1 — Crystal oscillator input |
| Pin produk 2 | OSC2 — Crystal oscillator output |
| Pin produk 3 | MCLR — Master clear reset (active low) |
| Pin produk 4 | RA0/AN0 — Port A bit 0 / ADC input 0 |
| Pin produk 5 | RA1/AN1 — Port A bit 1 / ADC input 1 |
| Pin produk 6 | RA2/AN2 — Port A bit 2 / ADC input 2 |
| Pin produk 7 | RA3/AN3 — Port A bit 3 / ADC input 3 |
| Pin produk 8 | RA4/AN4/T0CKI — Port A bit 4 / ADC input 4 / Timer 0 clock |
| Pin produk 9 | RA5/AN5 — Port A bit 5 / ADC input 5 |
| Pin produk 10 | RA6/AN6 — Port A bit 6 / ADC input 6 |
| Pin produk 11 | RA7/AN7 — Port A bit 7 / ADC input 7 |
| Pin produk 12 | VSS — Ground |
| Pin produk 13 | VDD — Positive supply voltage |
| Pin produk 14 | RB0/INT — Port B bit 0 / External interrupt |
| Pin produk 15 | RB1/AN8 — Port B bit 1 / ADC input 8 |
| Pin produk 16 | RB2/AN9 — Port B bit 2 / ADC input 9 |
| Pin produk 17 | RB3/AN10 — Port B bit 3 / ADC input 10 |
| Pin produk 18 | RB4/AN11 — Port B bit 4 / ADC input 11 |
| Pin produk 19 | RB5 — Port B bit 5 |
| Pin produk 20 | RB6 — Port B bit 6 |
| Pin produk 21 | RB7 — Port B bit 7 |
| Pin produk 22 | RC0 — Port C bit 0 |
| Pin produk 23 | RC1 — Port C bit 1 |
| Pin produk 24 | RC2 — Port C bit 2 |
| Pin produk 25 | RC3 — Port C bit 3 |
| Pin produk 26 | RC4 — Port C bit 4 |
| Pin produk 27 | RC5 — Port C bit 5 |
| Pin produk 28 | RC6/TX/CK — Port C bit 6 / USART TX |
| Pin produk 29 | RC7/RX/DT — Port C bit 7 / USART RX |
| Pin produk 30 | VSS — Ground |
| Pin produk 31 | VDD — Positive supply voltage |
| Pin produk 32 | RD0 — Port D bit 0 |
| Pin produk 33 | RD1 — Port D bit 1 |
| Pin produk 34 | RD2 — Port D bit 2 |
| Pin produk 35 | RD3 — Port D bit 3 |
| Pin produk 36 | RD4 — Port D bit 4 |
| Pin produk 37 | RD5 — Port D bit 5 |
| Pin produk 38 | RD6 — Port D bit 6 |
| Pin produk 39 | RD7 — Port D bit 7 |
| Pin produk 40 | RE0/AN12 — Port E bit 0 / ADC input 12 |
| Pin produk 41 | RE1/AN13 — Port E bit 1 / ADC input 13 |
| Pin produk 42 | RE2/AN14 — Port E bit 2 / ADC input 14 |
| Pin produk 43 | RE3/AN15 — Port E bit 3 / ADC input 15 |
| Pin produk 44 | VSS — Ground |
| Pin produk 45 | VDD — Positive supply voltage |
| Pin produk 46 | RF0 — Port F bit 0 |
| Pin produk 47 | RF1 — Port F bit 1 |
| Pin produk 48 | RF2 — Port F bit 2 |
| Pin produk 49 | RF3 — Port F bit 3 |
| Pin produk 50 | RF4 — Port F bit 4 |
| Pin produk 51 | RF5 — Port F bit 5 |
| Pin produk 52 | RF6 — Port F bit 6 |
| Pin produk 53 | RF7 — Port F bit 7 |
| Pin produk 54 | RG0 — Port G bit 0 |
| Pin produk 55 | RG1 — Port G bit 1 |
| Pin produk 56 | RG2 — Port G bit 2 |
| Pin produk 57 | RG3 — Port G bit 3 |
| Pin produk 58 | RG4 — Port G bit 4 |
| Pin produk 59 | AVSS — Analog ground |
| Pin produk 60 | AVDD — Analog positive supply |
| Pin produk 61 | VREF- — ADC negative reference |
| Pin produk 62 | VREF+ — ADC positive reference |
| Pin produk 63 | NC — Not connected (per datasheet) |
| Pin produk 64 | NC — Not connected (per datasheet) |
| Pin produk 65 | T1CKI/RC0 — Timer 1 clock input |
| Pin produk 66 | CCP1 — Capture/Compare/PWM output 1 |
| Pin produk 67 | SCK/SCL — SSP clock (SPI/I2C) |
| Pin produk 68 | SDI/SDA — SSP data input (SPI/I2C) |
| Pin produk 69 | SDO — SSP data output (SPI) |
| Pin produk 70 | SS — SSP slave select |
| Pin produk 71 | VSS — Ground |
| Pin produk 72 | VDD — Positive supply voltage |
| Pin produk 73 | NC — Not connected (per datasheet) |
| Pin produk 74 | NC — Not connected (per datasheet) |
| Pin produk 75 | NC — Not connected (per datasheet) |
| Pin produk 76 | NC — Not connected (per datasheet) |
| Pin produk 77 | NC — Not connected (per datasheet) |
| Pin produk 78 | NC — Not connected (per datasheet) |
| Pin produk 79 | NC — Not connected (per datasheet) |
| Pin produk 80 | NC — Not connected (per datasheet) |
Aplikasi Umum
PIC17LC762-08I/PT cocok untuk 6 aplikasis: Industrial Process Control, Motor Control Front-End, Instrumentation and Data Acquisition, Human-Machine Interface (HMI) Panels, Automotive Body Electronics (Non-Safety), Sensor Interface Boards.
Industrial Process Control
The PIC17LC762-08I/PT fits industrial process-control boards because of its 66 I/O pins (sufficient for 32-key keypads plus 7-segment or LCD displays), 10-bit ADC with 12 channels (good for 4-20 mA loop transmitters and bridge sensors), and 2.5-5.5 V operation. Industrial PLCs and remote terminal units (RTUs) benefit from the 33 MHz performance and the USART supporting RS-485 multidrop networks. Watchdog timer and brown-out reset provide the fail-safe behavior required by IEC 61131-2 industrial environments.
Direkomendasikan
Motor Control Front-End
Motor-control pre-drive boards use the PIC17LC762-08I/PT for sensor feedback and PWM generation because the 10-bit ADC samples current shunt amplifiers fast enough for 10 kHz control loops and the 16-bit timer drives the PWM base frequency. At 33 MHz the 121 ns instruction cycle supports field-oriented-control inner loops. The Capture/Compare/PWM (CCP) module generates complementary PWM outputs for three-phase inverter drivers, while 66 I/O accommodate Hall-effect sensors and fault inputs.
Direkomendasikan
Instrumentation and Data Acquisition
Bench-top instruments and data loggers use the PIC17LC762-08I/PT because its 12-channel 10-bit ADC multiplexes multiple thermocouple, RTD, or strain-gauge inputs, while 678 bytes of RAM buffers 250 samples at 12-bit equivalent oversampling rates. The USART streams data to a host PC at 115.2 kbps, and the I2C/SPI bus connects to external EEPROM for non-volatile storage. The -40C to +85C industrial temperature range supports outdoor environmental monitoring.
Direkomendasikan
Human-Machine Interface (HMI) Panels
Operator-interface panels with 4x4 to 8x8 keypad matrices and character or graphical LCDs benefit from the PIC17LC762's 66 I/O count, which can scan a 64-key matrix and drive a 40x4 character LCD with backlight control without external multiplexer ICs. The 16 KB OTP holds state-machine firmware for menu navigation, and the USART links to a host controller for parameter upload/download. The 80-pin TQFP gives clean PCB routing for the many parallel bus signals required by LCD modules.
Direkomendasikan
Automotive Body Electronics (Non-Safety)
Body-control modules (window lifters, mirror adjusters, seat controllers) historically used the PIC17LC762-08I/PT because its 66 I/O drive multiple relay and motor bridges directly through MOSFET pre-drivers. The wide 2.5-5.5 V supply tolerates 12 V automotive bus drops after pre-regulation. NOTE: this part is NOT AEC-Q100 qualified, so it is only suitable for non-safety body electronics; safety-critical ECUs require AEC-Q100 parts like dsPIC33EV variants.
Direkomendasikan
Sensor Interface Boards
Multi-sensor interface boards for HVAC, building automation, and environmental monitoring use the PIC17LC762-08I/PT because its 12 ADC inputs handle multiple analog sensors (temperature, humidity, pressure, light) simultaneously, while 66 digital I/O accommodate I2C/SPI sensor buses and digital switch inputs. The 2.5 V minimum supply supports battery-backed designs with 3.6 V lithium cells. Industrial temperature rating and watchdog timer ensure robust unattended operation.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC17LC762-08I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC17LC762-08I/L | PIC17LC756A-08I/PT | PIC17LC752T-08I/PT | PIC17C762-16I/PT | PIC17C762-16/PT | PIC17LC756AT-08I/L |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-80 (PT) | PLCC-68 (L) - different package | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | PLCC-68 (L) - different package |
| Program Memory | 16 KB OTP | 16 KB OTP | 16 KB OTP | 8 KB OTP (-50%) | 16 KB OTP | 16 KB OTP | 16 KB OTP |
| RAM Size | 678 bytes | 678 bytes | 678 bytes | 678 bytes | 678 bytes | 678 bytes | 678 bytes |
| I/O Pins | 66 | 50 (-24%) | 66 | 50 (-24%) | 66 | 66 | 50 (-24%) |
| Supply Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 2.5 V to 5.5 V |
| Max Clock Frequency | 33 MHz | 33 MHz | 33 MHz | 33 MHz | 33 MHz | 33 MHz | 33 MHz |
| Temperature Range | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | 0C to +70C (Commercial) | -40C to +85C |
Diferensiator Kunci
- Lower minimum supply voltage (vsPIC17C762-16I/PT)
- Industrial temperature grade vs commercial (vsPIC17C762-16/PT)
- Maximum program memory in the family (vsPIC17LC752T-08I/PT)
Catatan Desain
The PIC17LC762 requires a stable 2.5 V to 5.5 V supply on VDD with separate AVDD for the ADC. Place a 10 uF bulk capacitor and 0.1 uF decoupling capacitor as close as possible to each VDD/VSS pin pair. The PIC17's internal brown-out reset triggers at approximately 2.0 V; designs operating near the 2.5 V minimum should add external reset supervisor ICs (e.g., MCP100) for production margin because OTP programming requires a stable 5 V rail.
The 80-pin TQFP package uses 0.5 mm pitch pads requiring PCB trace widths of 0.2 mm (8 mil) or smaller. Use a 4-layer PCB with a continuous ground plane on layer 2 directly below the device to reduce EMI and provide thermal dissipation. Route the crystal traces (OSC1/OSC2) within 5 mm of the package with guard ground traces on both sides; long crystal traces pick up noise that corrupts the instruction cycle timing.
OTP (One-Time Programmable) memory cannot be erased or rewritten; once programmed, the PIC17LC762 cannot be reused. For prototype development, use the windowed PIC17C762/JW ceramic package (UV-erasable) or migrate to the flash-based PIC18F8722-I/PT. Programming the OTP requires a precise VPP voltage of 13.0 V to 13.25 V with a rise time under 1 ms - using a 12 V VPP will fail verification even if the device appears to program.
Keep ADC analog traces (AN0-AN15, VREF+, VREF-) away from digital switching signals and the USART lines. AVDD should be filtered with a ferrite bead from VDD, and AVSS should connect directly to the ground plane with a single via to avoid ground loops. The ADC's 10-bit accuracy is degraded by 1 LSB for every 50 mV of digital switching noise on the analog supply; this layout discipline is essential for instrumentation applications.
Informasi Konformitas
RoHS compliant per Microchip product page; NOT AEC-Q100 qualified - use dsPIC33EV variants for automotive. Halogen-free status not stated in verified data.