PIC24FJ192GA108-I/PT - 192KB Flash 16-bit MCU 80-TQFP | Microchip
MPN: PIC24FJ192GA108-I/PT ✓ AktifPIC24FJ192GA108-I/PT Ringkasan
A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory, data RAM, and peripherals (UART, SPI, I2C, ADC, timers) into a single chip. The PIC24F family belongs to the wider taxonomy: microcontroller -> embedded processor -> semiconductor IC. PIC24F parts use Microchip's modified Harvard RISC architecture with 16-bit instructions and 24-bit instruction words, designed to balance deterministic real-time response with low energy consumption for portable and battery-backed designs.
Key features of the PIC24FJ192GA108 include: 192 KB flash (65.5K x 24 words), 16 KB SRAM, 4 KB EEPROM-like data flash, 16 MIPS at 32 MHz CPU speed, and a peripheral set covering 3x I2C, 3x SPI, 4x UART, and 23 independent timers. The part supports USB, Real-Time Clock and Calendar (RTCC), 16-channel 10-bit ADC, and parallel master port, while integrated nanoWatt XLP technology keeps standby draw below 100 nA.
Internally the device separates regulated core power (1.8V via internal LDO) from I/O power (2.0-3.6V), enabling mixed-voltage peripherals. The 80-pin TQFP exposes up to 69 digital I/O lines and supports 5V-tolerant inputs, while programming is handled through ICSP and JTAG. This combination of high memory density and rich connectivity makes the part suitable for applications that previously required multiple 8-bit MCUs.
Typical applications include industrial sensor hubs, low-power wireless gateways, USB human-interface devices (HID), battery-backed data loggers, and consumer appliances requiring graphical LCDs via integrated PMP. The 4x UART channels are particularly useful for protocol-bridging gateways (RS-232/485 to USB) and the parallel master port can directly drive external graphics memory.
When designing with this device, ensure all VSS/VDD pins are connected per datasheet, ENVREG is configured correctly for internal vs external voltage regulator mode, and the JTAG/ICSP pins are reserved for in-circuit debugging unless disabled in firmware.
This page synthesizes distributor pricing, drop-in alternatives, application notes, and PCB layout guidance not found in the manufacturer datasheet alone.
Alternatif penggantian untuk PIC24FJ192GA108-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC24FJ192GA108-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam Package, Standby Current, Timers, ADC, Core Architecture.
PIC24FJ192GA106-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC24FJ128GA108-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC24FJ256GA108-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC24FJ192GB108-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC24FJ256GB108-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC24FJ128GB106-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC24FJ192GA108-I/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | PIC24F (16-bit RISC, modified Harvard) |
| Program Flash Memory | 192 KB (65.5K x 24 words) |
| Data RAM | 16 KB |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Operating Voltage (VDD) | 2.0 V to 3.6 V |
| Standby Current | <100 nA (nanoWatt XLP) |
| I/O Count | 69 digital I/O |
| ADC | 16-channel 10-bit |
| UART | 4 |
| SPI | 3 |
| I2C | 3 |
| Timers | 23 independent |
| USB | Yes (Full-Speed) |
| RTCC | Yes (Real-Time Clock and Calendar) |
| Parallel Master Port (PMP) | Yes |
| Paket | TQFP-80 (PT), 12x12 mm |
| Tipe Mounting | Surface Mount |
| Suhu Kerja | -40 C to +85 C (Industrial, -I) |
| Level MSL | 3 |
| Status RoHS | Compliant |
| Lead-Free / Halogen-Free | Yes / Yes |
Konfigurasi Pin PIC24FJ192GA108-I/PT
| Pin produk 1 | RP15/RB15 — Remappable I/O / general purpose I/O pin B15 |
| Pin produk 2 | RP14/RB14 — Remappable I/O / general purpose I/O pin B14 |
| Pin produk 3 | RP13/RB13 — Remappable I/O / general purpose I/O pin B13 |
| Pin produk 4 | RP12/RB12 — Remappable I/O / general purpose I/O pin B12 |
| Pin produk 5 | AVDD — Analog supply voltage |
| Pin produk 6 | AVSS — Analog ground |
| Pin produk 7 | RP11/RB11 — Remappable I/O / general purpose I/O pin B11 |
| Pin produk 8 | RP10/RB10 — Remappable I/O / general purpose I/O pin B10 |
| Pin produk 9 | RP9/RB9 — Remappable I/O / general purpose I/O pin B9 |
| Pin produk 10 | RP8/RB8 — Remappable I/O / general purpose I/O pin B8 |
| Pin produk 11 | RP7/RB7 — Remappable I/O / general purpose I/O pin B7 |
| Pin produk 12 | RP6/RB6 — Remappable I/O / general purpose I/O pin B6 |
| Pin produk 13 | RP5/RB5 — Remappable I/O / general purpose I/O pin B5 |
| Pin produk 14 | RP4/RB4 — Remappable I/O / general purpose I/O pin B4 |
| Pin produk 15 | RP3/RB3 — Remappable I/O / general purpose I/O pin B3 |
| Pin produk 16 | RP2/RB2 — Remappable I/O / general purpose I/O pin B2 |
| Pin produk 17 | RP1/RB1 — Remappable I/O / general purpose I/O pin B1 |
| Pin produk 18 | RP0/RB0 — Remappable I/O / general purpose I/O pin B0 |
| Pin produk 19 | VDD — Digital supply voltage |
| Pin produk 20 | VSS — Digital ground |
| Pin produk 21 | OSC1/RC0 — Crystal oscillator input or general I/O RC0 |
| Pin produk 22 | OSC2/RC1 — Crystal oscillator output or general I/O RC1 |
| Pin produk 23 | RC2 — General purpose I/O pin C2 |
| Pin produk 24 | RC3 — General purpose I/O pin C3 |
| Pin produk 25 | RC4 — General purpose I/O pin C4 |
| Pin produk 26 | RC5 — General purpose I/O pin C5 |
| Pin produk 27 | ENVREG — Enable for internal voltage regulator |
| Pin produk 28 | VDD — Digital supply voltage |
| Pin produk 29 | VSS — Digital ground |
| Pin produk 30 | RD0 — General purpose I/O pin D0 |
| Pin produk 31 | RD1 — General purpose I/O pin D1 |
| Pin produk 32 | RD2 — General purpose I/O pin D2 |
| Pin produk 33 | RD3 — General purpose I/O pin D3 |
| Pin produk 34 | RD4 — General purpose I/O pin D4 |
| Pin produk 35 | RD5 — General purpose I/O pin D5 |
| Pin produk 36 | RD6 — General purpose I/O pin D6 |
| Pin produk 37 | RD7 — General purpose I/O pin D7 |
| Pin produk 38 | VDD — Digital supply voltage |
| Pin produk 39 | VSS — Digital ground |
| Pin produk 40 | RD8 — General purpose I/O pin D8 |
| Pin produk 41 | RD9 — General purpose I/O pin D9 |
| Pin produk 42 | RD10 — General purpose I/O pin D10 |
| Pin produk 43 | RD11 — General purpose I/O pin D11 |
| Pin produk 44 | RD12 — General purpose I/O pin D12 |
| Pin produk 45 | RD13 — General purpose I/O pin D13 |
| Pin produk 46 | RD14 — General purpose I/O pin D14 |
| Pin produk 47 | RD15 — General purpose I/O pin D15 |
| Pin produk 48 | RF0 — General purpose I/O pin F0 |
| Pin produk 49 | RF1 — General purpose I/O pin F1 |
| Pin produk 50 | RF2 — General purpose I/O pin F2 |
| Pin produk 51 | RF3 — General purpose I/O pin F3 |
| Pin produk 52 | RF4 — General purpose I/O pin F4 |
| Pin produk 53 | RF5 — General purpose I/O pin F5 |
| Pin produk 54 | RF6 — General purpose I/O pin F6 |
| Pin produk 55 | RF7 — General purpose I/O pin F7 |
| Pin produk 56 | VDD — Digital supply voltage |
| Pin produk 57 | VSS — Digital ground |
| Pin produk 58 | RG0 — General purpose I/O pin G0 |
| Pin produk 59 | RG1 — General purpose I/O pin G1 |
| Pin produk 60 | RG2 — General purpose I/O pin G2 |
| Pin produk 61 | RG3 — General purpose I/O pin G3 |
| Pin produk 62 | RG4 — General purpose I/O pin G4 |
| Pin produk 63 | RG5 — General purpose I/O pin G5 |
| Pin produk 64 | RG6 — General purpose I/O pin G6 |
| Pin produk 65 | RG7 — General purpose I/O pin G7 |
| Pin produk 66 | RG8 — General purpose I/O pin G8 |
| Pin produk 67 | RG9 — General purpose I/O pin G9 |
| Pin produk 68 | RG10 — General purpose I/O pin G10 |
| Pin produk 69 | RG11 — General purpose I/O pin G11 |
| Pin produk 70 | VDD — Digital supply voltage |
| Pin produk 71 | VSS — Digital ground |
| Pin produk 72 | RG12 — General purpose I/O pin G12 |
| Pin produk 73 | RG13 — General purpose I/O pin G13 |
| Pin produk 74 | RG14 — General purpose I/O pin G14 |
| Pin produk 75 | RG15 — General purpose I/O pin G15 |
| Pin produk 76 | MCLR — Master Clear (reset) input |
| Pin produk 77 | RA0 — General purpose I/O pin A0 |
| Pin produk 78 | RA1 — General purpose I/O pin A1 |
| Pin produk 79 | RA2 — General purpose I/O pin A2 |
| Pin produk 80 | RA3 — General purpose I/O pin A3 |
Aplikasi Umum
PIC24FJ192GA108-I/PT cocok untuk 7 aplikasis: Low-Power Wireless Sensor Hub, USB Human Interface Device (HID), Industrial Protocol Bridge Gateway, Battery-Backed Data Logger, Consumer Appliance with Graphical LCD, Portable Medical Monitoring Device, IoT Edge Node with USB Debug.
Low-Power Wireless Sensor Hub
The PIC24FJ192GA108-I/PT suits battery-backed wireless sensor hubs because its 192 KB flash accommodates full Zigbee/LoRaWAN stack libraries plus application firmware, while sub-100 nA standby current extends coin-cell life to multi-year timescales. The 4x UART channels handle concurrent RS-485 sensor buses, the 3x SPI bus drives radio modules, and the 16 KB RAM buffers measurement packets between transmissions. The integrated RTCC schedules periodic wake-ups without CPU intervention, and 16-channel 10-bit ADC reads analog sensors directly. Engineers benefit from a single-chip solution replacing an external RTC + EEPROM + 8-bit MCU trio.
Direkomendasikan
USB Human Interface Device (HID)
The PIC24FJ192GA108-I/PT integrates Full-Speed USB 2.0 device with on-chip transceiver, eliminating the external PHY required by older PIC18 designs. The 16 MIPS performance handles USB HID polling at 1 kHz with ample headroom for key-matrix scanning, LED PWM control, and boot-loader firmware in the 192 KB flash. The 4x UARTs can bridge legacy serial peripherals over USB CDC, and 23 independent timers support debounce, backlight dimming, and capacitive-touch sampling. Power delivery through USB VBUS simplifies single-cable designs, while industrial -40 C to +85 C temperature rating supports harsh-environment input devices.
Direkomendasikan
Industrial Protocol Bridge Gateway
The PIC24FJ192GA108-I/PT fits multi-protocol industrial gateways because it offers 4x UARTs for concurrent RS-232/RS-485 buses plus 3x SPI and 3x I2C for sensor and EEPROM interconnects. The 16 KB RAM and 192 KB flash store Modbus RTU, Modbus TCP, and proprietary protocol stacks simultaneously. The RTCC timestamps event logs, the 10-bit ADC monitors supply rails for fault detection, and the parallel master port drives an external LCD for local HMI. Industrial -40 C to +85 C rating allows deployment in factory-floor cabinets, and nanoWatt XLP modes cut idle draw below 100 nA between polling cycles.
Direkomendasikan
Battery-Backed Data Logger
The PIC24FJ192GA108-I/PT serves battery-backed data loggers because the 192 KB flash doubles as data-flash storage (wear-leveled by MPLAB Harmony drivers), and the 16 KB RAM buffers high-speed ADC samples between writes. Sub-100 nA standby current lets a CR2032 cell sustain years of logging-only operation, while the integrated RTCC provides accurate timestamps without external crystals. The 16-channel 10-bit ADC scans multiple analog inputs (temperature, voltage, current) sequentially, and the I2C/SPI buses connect external FRAM or SD-card storage when higher capacity is needed.
Direkomendasikan
Consumer Appliance with Graphical LCD
The PIC24FJ192GA108-I/PT drives graphical LCD panels directly through its integrated Parallel Master Port (PMP), which supports 8-bit and 16-bit wide buses plus chip-select control. The 192 KB flash stores multi-language UI assets and bitmap fonts, while the 16 MIPS core refreshes the display at 30+ FPS for animated icons. The 4x UART channels connect to Wi-Fi/BLE modules for IoT-enabled appliances, the 16-channel ADC reads temperature and humidity sensors, and 23 timers handle PWM backlight dimming plus capacitive touch sensing. The industrial -40 C to +85 C rating supports kitchen and laundry environments.
Direkomendasikan
Portable Medical Monitoring Device
The PIC24FJ192GA108-I/PT suits portable patient monitors because the 16 MIPS core runs sensor fusion and ECG/PPG algorithms in real time, while 16 KB RAM stores rolling waveform buffers. The integrated Full-Speed USB enables tethered data upload to clinical PCs, and the RTCC timestamps events for diagnostic logs. The 16-channel 10-bit ADC reads multiple bioelectric signals with proper sequencing, and 23 timers manage precise sampling intervals critical for heart-rate detection. Sub-100 nA standby preserves battery life between patient sessions, while the 2.0-3.6V VDD range supports direct Li-ion supply.
Direkomendasikan
IoT Edge Node with USB Debug
The PIC24FJ192GA108-I/PT is well suited for IoT edge nodes that need USB diagnostics during development. The integrated Full-Speed USB allows direct connection to a host PC for firmware updates, log dumps, and real-time debug without external debug ICs. The 192 KB flash holds TCP/IP or MQTT client stacks alongside application logic, while the 4x UARTs bridge to LoRa, NB-IoT, or Wi-Fi modules. The 23 timers drive sensor sampling schedules without CPU load, the RTCC maintains accurate time-of-day across sleep cycles, and the 16-channel ADC reads analog environmental sensors in parallel.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC24FJ192GA108-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC24FJ192GA106-I/PT | PIC24FJ128GA108-I/PT | PIC24FJ256GA108-I/PT | PIC24FJ192GB108-I/PT | PIC24FJ256GB108-I/PT | PIC24FJ128GB106-I/PT |
|---|---|---|---|---|---|---|---|
| Package | TQFP-80 (PT), 12x12 mm | TQFP-64 (PT) - 64-pin variant | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Flash | 192 KB | 192 KB | 128 KB (-33%) | 256 KB (+33%) | 192 KB | 256 KB (+33%) | 128 KB (-33%) |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| Maximum CPU Speed | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS |
| USB | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 OTG (Host+Device) | USB 2.0 OTG (Host+Device) | USB 2.0 OTG (Host+Device) |
| Standby Current | <100 nA | <100 nA | <100 nA | <100 nA | <100 nA | <100 nA | <100 nA |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| UART / SPI / I2C Count | 4 / 3 / 3 | 4 / 3 / 3 | 4 / 3 / 3 | 4 / 3 / 3 | 4 / 3 / 3 | 4 / 3 / 3 | 4 / 3 / 3 |
Diferensiator Kunci
- Higher flash density in 80-pin TQFP at standard -I temperature grade (vsPIC24FJ128GA108-I/PT)
- Standard USB Device vs OTG upgrade choice (vsPIC24FJ192GB108-I/PT)
- Industrial -40 C to +85 C temperature grade standard (vsPIC24FJ192GA108-E/PT (extended grade))
Catatan Desain
Connect all VDD and VSS pins (pins 19, 20, 28, 29, 38, 39, 56, 57, 70, 71). Per Microchip datasheet section 2.4, leaving any supply pin disconnected can cause programming failures or unstable operation. Place 100 nF decoupling capacitors within 5 mm of each VDD pin and a single 10 uF bulk capacitor near the IC. Configure ENVREG (pin 27) tied to VDD for internal 1.8V core regulator mode, or to a 1.8V external rail if bypassing the internal LDO.
Route the 32 MHz crystal traces (OSC1/OSC2, pins 21/22) as short as possible with a guard ring to ground to minimize EMI pickup. Place crystal within 5 mm of the MCU and avoid routing digital signal traces under the crystal pads. Use a 4-layer PCB with a dedicated ground plane beneath the MCU; the exposed thermal pad of the TQFP package improves thermal dissipation under heavy peripheral load.
Do not assume any PIC24F pin is 5V tolerant without checking the datasheet. Most I/O on the PIC24FJ192GA108 are 5V tolerant only when the pin is configured as digital input; analog or output modes limit to VDD. Also, when migrating from PIC24FJ64GA108 firmware, the larger flash and RAM require updates to the linker script and startup file; do not blindly reuse the old project. Lastly, the JTAG/ICSP pins (MCLR, PGECx, PGEDx) must be reserved for in-circuit debugging unless disabled in configuration bits.
Informasi Konformitas
RoHS and lead-free compliant per Microchip product page. Not AEC-Q100 qualified; for automotive applications use PIC24FJ192GA108-I/PT only in non-safety-critical subsystems or select AEC-Q100 qualified PIC variants. REACH compliance declared by Microchip.