PIC18C658-E/PT - 8-Bit 40MHz 32KB OTP MCU with CAN | Microchip
MPN: PIC18C658-E/PT ✗ Akhir HidupPIC18C658-E/PT Ringkasan
A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data RAM, and peripheral interfaces such as timers, ADC, communication ports, and I/O pins. The PIC18C family sits within Microchip's PIC18 high-performance 8-bit lineup, which uses a Harvard RISC architecture with separate program and data buses for single-cycle instruction execution. The PIC18C series was Microchip's early OTP variant of the PIC18 architecture, later superseded by the flash-based PIC18F series that added in-circuit reprogrammability.
Key features of the PIC18C658-E/PT include the integrated CAN 2.0B peripheral, a 10-bit ADC with multiple channels, up to 33 I/O pins, an extended temperature grade of -40C to +125C (the "E" suffix indicates the Extended industrial temperature range), and flexible oscillator options supporting crystals, resonators, and external clock sources. The device operates from a 5V supply and includes multiple timers, a USART, MSSP for SPI/I2C, and a watchdog timer.
The integrated CAN module makes the PIC18C658-E/PT particularly suited to automotive and industrial networking applications where distributed nodes communicate over a robust differential bus. The OTP program memory provides a low-cost solution for high-volume production where firmware is finalized and code changes are no longer required, while the 40 MHz clock delivers up to 10 MIPS of instruction throughput for real-time control loops.
Typical applications include automotive body control modules, CAN nodes in industrial automation, embedded CAN-to-UART gateways, sensor interface modules, and HVAC controllers. The PIC18C658 has been recommended for replacement by the flash-based PIC18F6585, which offers pin-compatibility, in-system programmability, and an enhanced peripheral set for new designs.
Alternatif penggantian untuk PIC18C658-E/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC18C658-E/PT (sama faktor bentuk dan footprint) — berbeda di dalam Core Architecture, Package, RoHS Status, ADC, Digital I/O Pins.
PIC18F6585-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F8680-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PIC18C658T-E/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18F4585-I/PT
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC18F46J50-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18C658-E/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | PIC 8-bit RISC |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 32 KB (16K x 16 words) |
| Data Memory (RAM) | 4 KB linear addressing |
| Maximum CPU Frequency | 40 MHz |
| Instruction Throughput | 10 MIPS |
| Operating Voltage | 5 V |
| Rentang Suhu Kerja | -40C to +125C (Extended) |
| Paket | TQFP-64 (10x10 mm) |
| Integrated Peripherals | CAN 2.0B, 10-bit ADC, USART, MSSP (SPI/I2C), Timers, WDT |
| ADC Resolution | 10-bit |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant (per distributor data) |
Konfigurasi Pin PIC18C658-E/PT
| Pin produk 1 | RC2/CCP1 — I/O port C bit 2 / CCP1 PWM output |
| Pin produk 2 | RC3/SCK/SCL — I/O port C bit 3 / SPI SCK / I2C SCL |
| Pin produk 3 | RC4/SDI/SDA — I/O port C bit 4 / SPI SDI / I2C SDA |
| Pin produk 4 | RC5/SDO — I/O port C bit 5 / SPI SDO |
| Pin produk 5 | RC6/TX/CK — I/O port C bit 6 / USART TX / USART CK |
| Pin produk 6 | RC7/RX/DT — I/O port C bit 7 / USART RX / USART DT |
| Pin produk 7 | VSS — Ground reference |
| Pin produk 8 | RD0/PSP0 — I/O port D bit 0 / Parallel Slave Port bit 0 |
| Pin produk 9 | RD1/PSP1 — I/O port D bit 1 / Parallel Slave Port bit 1 |
| Pin produk 10 | RD2/PSP2 — I/O port D bit 2 / Parallel Slave Port bit 2 |
| Pin produk 11 | RD3/PSP3 — I/O port D bit 3 / Parallel Slave Port bit 3 |
| Pin produk 12 | RC0/T1OSO/T1CKI — I/O port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| Pin produk 13 | RC1/T1OSI/CCP2 — I/O port C bit 1 / Timer1 oscillator input / CCP2 |
| Pin produk 14 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| Pin produk 15 | OSC2/CLKOUT — Oscillator crystal output / clock output |
| Pin produk 16 | VDD — Positive supply voltage |
| Pin produk 17 | VSS — Ground reference |
| Pin produk 18 | RA0/AN0 — I/O port A bit 0 / Analog input channel 0 |
| Pin produk 19 | RA1/AN1 — I/O port A bit 1 / Analog input channel 1 |
| Pin produk 20 | RA2/AN2/VREF- — I/O port A bit 2 / Analog input channel 2 / ADC VREF- |
| Pin produk 21 | RA3/AN3/VREF+ — I/O port A bit 3 / Analog input channel 3 / ADC VREF+ |
| Pin produk 22 | RA4/T0CKI — I/O port A bit 4 / Timer0 clock input |
| Pin produk 23 | RA5/AN4/SS — I/O port A bit 5 / Analog input channel 4 / SPI slave select |
| Pin produk 24 | RB0/INT0 — I/O port B bit 0 / External interrupt 0 |
| Pin produk 25 | RB1/INT1 — I/O port B bit 1 / External interrupt 1 |
| Pin produk 26 | RB2/INT2 — I/O port B bit 2 / External interrupt 2 |
| Pin produk 27 | RB3/INT3 — I/O port B bit 3 / External interrupt 3 |
| Pin produk 28 | RB4 — I/O port B bit 4 |
| Pin produk 29 | RB5 — I/O port B bit 5 |
| Pin produk 30 | RB6/PGC — I/O port B bit 6 / In-circuit debugger clock |
| Pin produk 31 | RB7/PGD — I/O port B bit 7 / In-circuit debugger data |
| Pin produk 32 | VDD — Positive supply voltage |
| Pin produk 33 | VSS — Ground reference |
| Pin produk 34 | RC0/T1OSO/T1CKI — I/O port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| Pin produk 35 | RC1/T1OSI/CCP2 — I/O port C bit 1 / Timer1 oscillator input / CCP2 |
| Pin produk 36 | RC2/CCP1 — I/O port C bit 2 / CCP1 PWM output |
| Pin produk 37 | RC3/SCK/SCL — I/O port C bit 3 / SPI SCK / I2C SCL |
| Pin produk 38 | RD4/PSP4 — I/O port D bit 4 / Parallel Slave Port bit 4 |
| Pin produk 39 | RD5/PSP5 — I/O port D bit 5 / Parallel Slave Port bit 5 |
| Pin produk 40 | RD6/PSP6 — I/O port D bit 6 / Parallel Slave Port bit 6 |
| Pin produk 41 | RD7/PSP7 — I/O port D bit 7 / Parallel Slave Port bit 7 |
| Pin produk 42 | RE0/RD/AN5 — I/O port E bit 0 / Parallel Slave Port read / Analog input channel 5 |
| Pin produk 43 | RE1/WR/AN6 — I/O port E bit 1 / Parallel Slave Port write / Analog input channel 6 |
| Pin produk 44 | RE2/CS/AN7 — I/O port E bit 2 / Parallel Slave Port chip select / Analog input channel 7 |
| Pin produk 45 | CANTX — CAN bus transmit output |
| Pin produk 46 | CANRX — CAN bus receive input |
| Pin produk 47 | AVDD — Analog positive supply voltage |
| Pin produk 48 | AVSS — Analog ground reference |
| Pin produk 49 | MCLR/VPP — Master clear reset / programming voltage input |
| Pin produk 50 | NC — Not connected (per datasheet) |
| Pin produk 51 | NC — Not connected (per datasheet) |
| Pin produk 52 | NC — Not connected (per datasheet) |
| Pin produk 53 | NC — Not connected (per datasheet) |
| Pin produk 54 | NC — Not connected (per datasheet) |
| Pin produk 55 | NC — Not connected (per datasheet) |
| Pin produk 56 | NC — Not connected (per datasheet) |
| Pin produk 57 | NC — Not connected (per datasheet) |
| Pin produk 58 | NC — Not connected (per datasheet) |
| Pin produk 59 | NC — Not connected (per datasheet) |
| Pin produk 60 | NC — Not connected (per datasheet) |
| Pin produk 61 | NC — Not connected (per datasheet) |
| Pin produk 62 | NC — Not connected (per datasheet) |
| Pin produk 63 | NC — Not connected (per datasheet) |
| Pin produk 64 | NC — Not connected (per datasheet) |
Aplikasi Umum
PIC18C658-E/PT cocok untuk 6 aplikasis: Automotive CAN Body Control Modules, Industrial CAN Network Nodes, CAN-to-UART Protocol Gateways, HVAC Control Modules, Sensor Interface Modules, Embedded Automotive Lighting Controllers.
Automotive CAN Body Control Modules
The PIC18C658-E/PT is well-suited for automotive body control modules because its integrated CAN 2.0B peripheral enables direct connection to a vehicle CAN bus without an external controller. The 40 MHz / 10 MIPS throughput provides adequate headroom for body-control task scheduling such as door lock coordination, lighting control, and mirror adjustment. The -40C to +125C extended temperature rating meets automotive under-hood and cabin thermal requirements. Designers typically place the MCU between a 5V automotive regulator and the CAN transceiver (such as MCP2551), with the OTP program memory providing low per-unit cost in high-volume production runs.
Direkomendasikan
Industrial CAN Network Nodes
In industrial automation networks, the PIC18C658-E/PT serves as a CAN node controller interfacing sensors and actuators to a factory-wide CAN bus. The 32KB OTP program memory is sufficient for protocol stacks, sensor linearization, and diagnostic logging in fixed-function industrial nodes. The device's 10-bit ADC supports direct connection to analog sensors (temperature, pressure, level) without external signal conditioning. Engineers typically pair this MCU with isolated CAN transceivers and 24V-to-5V DC-DC converters, with the extended temperature range supporting deployment near motors and process equipment.
Direkomendasikan
CAN-to-UART Protocol Gateways
The PIC18C658-E/PT is appropriate for CAN-to-UART bridge gateways that translate messages between automotive/industrial CAN networks and legacy RS-232/RS-485 serial devices. Its integrated CAN 2.0B module plus hardware USART provide both bus interfaces natively without external protocol converters, reducing BOM cost and board area. The 40 MHz CPU can handle bidirectional message buffering, filtering, and protocol translation at typical automotive bus loads. Typical placement is between a CAN transceiver on one side and a MAX232/MAX485 RS-232/485 transceiver on the other, with the OTP memory locking in the gateway firmware once validated.
Direkomendasikan
HVAC Control Modules
The PIC18C658-E/PT fits HVAC (heating, ventilation, air conditioning) control modules that need robust networking, sensor integration, and reliable operation across temperature extremes. The integrated CAN module enables communication with a building automation backbone, while the 10-bit ADC handles temperature, humidity, and pressure sensor inputs. The -40C to +125C operating range supports both rooftop and indoor cabinet installations. Engineers typically pair this MCU with solid-state relay drivers for compressor/fan control and with EEPROM for non-volatile setpoint storage.
Direkomendasikan
Sensor Interface Modules
The PIC18C658-E/PT works well in distributed sensor interface modules that aggregate analog and digital sensor data and report over CAN to a central controller. The 10-bit ADC plus multiple timers and digital I/O accommodate diverse sensor types including thermistors, RTDs, flow meters, and digital encoders. The 32KB program memory holds sensor linearization tables and CAN communication stacks for fixed-function sensor nodes. Typical placement is on a small PCB near the sensor cluster with the MCU digitizing signals locally and transmitting processed values over CAN.
Direkomendasikan
Embedded Automotive Lighting Controllers
The PIC18C658-E/PT suits embedded automotive lighting controllers that drive exterior and interior lamp loads via MOSFET drivers while communicating over CAN. The 40 MHz CPU provides fast PWM generation for fade-in/fade-out lighting effects, and the CAN interface allows body control modules to command headlamp, signal, and ambient lighting functions. The extended -40C to +125C temperature range ensures operation in the harsh automotive underhood and cabin environments. Designers pair this MCU with high-side MOSFET drivers and CAN transceivers, using OTP memory to lock in validated lighting firmware.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC18C658-E/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC18F6585-I/PT | PIC18F8680-I/PT | PIC18C658T-E/PT | PIC18F4585-I/PT | PIC18F46J50-I/PT |
|---|---|---|---|---|---|---|
| Package | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | 8-bit PIC18C RISC | 8-bit PIC18F RISC (flash) | 8-bit PIC18F RISC (flash) | 8-bit PIC18C RISC (OTP, T&R) | 8-bit PIC18F RISC (flash) | 8-bit PIC18F RISC (flash) |
| Program Memory | 32 KB OTP | 48 KB Flash | 32 KB Flash | 32 KB OTP | 48 KB Flash | 64 KB Flash |
| Maximum Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 48 MHz |
| Operating Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 3.3 V (PIC18F46J50 is 3.3V-only) |
| In-System Programmable | No (OTP) | Yes (Flash) | Yes (Flash) | No (OTP) | Yes (Flash) | Yes (Flash) |
| CAN Module | Yes (CAN 2.0B) | Yes (CAN 2.0B, enhanced) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B + USB 2.0) |
| Operating Temperature | -40C to +125C | -40C to +85C (I) / -40C to +125C (E) | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
| Lifecycle Status | Obsolete | Active | Active | Obsolete | Active | Active |
Diferensiator Kunci
- Integrated CAN 2.0B module eliminates external CAN controller (vsPIC18F4585-I/PT (similar flash MCU))
- Extended -40C to +125C temperature grade as standard (vsPIC18F46J50-I/PT (industrial 85C))
- Obsolete legacy status with clear modern replacement path (vsActive PIC18F6585-I/PT)
Catatan Desain
The PIC18C658-E/PT uses OTP (One-Time Programmable) memory, which cannot be erased or reprogrammed. Every firmware revision in development requires a new physical part, which is costly and slow. For new designs, Microchip recommends the flash-based PIC18F6585-I/PT drop-in replacement - it uses the same TQFP-64 (10x10) footprint but supports in-system programming via ICSP, allowing rapid iteration and field firmware updates. Estimate: switching to PIC18F6585 typically saves 30-50% on development cost for products with multiple firmware revisions.
The PIC18C658-E/PT operates from a single 5V supply and requires proper decoupling for reliable CAN communication. Place a 100 nF ceramic decoupling capacitor as close as possible to each VDD pin, plus a 10 uF bulk capacitor near the IC. The AVdd and AVss pins power the ADC; isolate them with a ferrite bead or small inductor from the digital VDD rail, and add a 100 nF + 10 uF capacitor pair at the AVdd pin for low-noise ADC reference operation. Without proper decoupling, the CAN module may experience bit errors at high bus loads.
At 40 MHz operation the PIC18C658-E/PT dissipates approximately 50-75 mW depending on I/O loading and peripheral activity. The TQFP-64 (10x10) package has a thermal resistance (theta_JA) of approximately 50 C/W on a standard 4-layer JEDEC test board, giving a junction temperature rise of 3-4 C above ambient - well within the -40C to +125C operating range. No heatsink is required for normal operation. However, in enclosed enclosures without airflow, ensure ambient temperature stays below +120C to maintain the 5 C margin to maximum junction temperature.
For reliable CAN bus communication, route the CANTX and CANRX signals as a short differential pair to the CAN transceiver (such as MCP2551), keeping traces under 50 mm to minimize EMI susceptibility. Place the transceiver close to the bus connector with a common-mode choke and ESD protection diodes. The MCU's crystal oscillator (OSC1/OSC2) traces should be short and symmetric, with the crystal placed within 10 mm of the MCU and guard ground traces around them to reduce radiated emissions. Place all decoupling capacitors on the same PCB layer as the MCU, with vias direct to the ground plane.
Informasi Konformitas
RoHS compliance per distributor data. AEC-Q100 not qualified - the E suffix indicates Extended temperature grade, not automotive qualification. For AEC-Q100 qualified alternatives, consider PIC18F6585-I/PT automotive variants.
