PIC18C658-E/PT - 8-Bit 40MHz 32KB OTP MCU with CAN | Microchip
부품 번호: PIC18C658-E/PT ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $14.5 | $14.50 |
| 10 | $12.95 | $129.50 |
| 100 | $11.4 | $1,140.00 |
| 500 | $9.85 | $4,925.00 |
| 1,000 | $8.6 | $8,600.00 |
PIC18C658-E/PT 개요
A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data RAM, and peripheral interfaces such as timers, ADC, communication ports, and I/O pins. The PIC18C family sits within Microchip's PIC18 high-performance 8-bit lineup, which uses a Harvard RISC architecture with separate program and data buses for single-cycle instruction execution. The PIC18C series was Microchip's early OTP variant of the PIC18 architecture, later superseded by the flash-based PIC18F series that added in-circuit reprogrammability.
Key features of the PIC18C658-E/PT include the integrated CAN 2.0B peripheral, a 10-bit ADC with multiple channels, up to 33 I/O pins, an extended temperature grade of -40C to +125C (the "E" suffix indicates the Extended industrial temperature range), and flexible oscillator options supporting crystals, resonators, and external clock sources. The device operates from a 5V supply and includes multiple timers, a USART, MSSP for SPI/I2C, and a watchdog timer.
The integrated CAN module makes the PIC18C658-E/PT particularly suited to automotive and industrial networking applications where distributed nodes communicate over a robust differential bus. The OTP program memory provides a low-cost solution for high-volume production where firmware is finalized and code changes are no longer required, while the 40 MHz clock delivers up to 10 MIPS of instruction throughput for real-time control loops.
Typical applications include automotive body control modules, CAN nodes in industrial automation, embedded CAN-to-UART gateways, sensor interface modules, and HVAC controllers. The PIC18C658 has been recommended for replacement by the flash-based PIC18F6585, which offers pin-compatibility, in-system programmability, and an enhanced peripheral set for new designs.
드롭인 대체품: PIC18C658-E/PT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18C658-E/PT (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Package, RoHS Status, ADC, Digital I/O Pins.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F6585-I/PT
✅ 드롭인✓ 재고 있음
$6.95 / 개
데이터시트 보기 →PIC18F8680-I/PT
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
PIC18C658T-E/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F4585-I/PT
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.73 / 개
데이터시트 보기 →PIC18F46J50-I/PT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18C658-E/PT 최대 정격 & 전기적 특성
| Core Architecture | PIC 8-bit RISC |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 32 KB (16K x 16 words) |
| Data Memory (RAM) | 4 KB linear addressing |
| Maximum CPU Frequency | 40 MHz |
| Instruction Throughput | 10 MIPS |
| Operating Voltage | 5 V |
| 동작 온도 범위 | -40C to +125C (Extended) |
| 패키지 | TQFP-64 (10x10 mm) |
| Integrated Peripherals | CAN 2.0B, 10-bit ADC, USART, MSSP (SPI/I2C), Timers, WDT |
| ADC Resolution | 10-bit |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant (per distributor data) |
PIC18C658-E/PT 핀 구성
| 핀 1 | RC2/CCP1 — I/O port C bit 2 / CCP1 PWM output |
| 핀 2 | RC3/SCK/SCL — I/O port C bit 3 / SPI SCK / I2C SCL |
| 핀 3 | RC4/SDI/SDA — I/O port C bit 4 / SPI SDI / I2C SDA |
| 핀 4 | RC5/SDO — I/O port C bit 5 / SPI SDO |
| 핀 5 | RC6/TX/CK — I/O port C bit 6 / USART TX / USART CK |
| 핀 6 | RC7/RX/DT — I/O port C bit 7 / USART RX / USART DT |
| 핀 7 | VSS — Ground reference |
| 핀 8 | RD0/PSP0 — I/O port D bit 0 / Parallel Slave Port bit 0 |
| 핀 9 | RD1/PSP1 — I/O port D bit 1 / Parallel Slave Port bit 1 |
| 핀 10 | RD2/PSP2 — I/O port D bit 2 / Parallel Slave Port bit 2 |
| 핀 11 | RD3/PSP3 — I/O port D bit 3 / Parallel Slave Port bit 3 |
| 핀 12 | RC0/T1OSO/T1CKI — I/O port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| 핀 13 | RC1/T1OSI/CCP2 — I/O port C bit 1 / Timer1 oscillator input / CCP2 |
| 핀 14 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| 핀 15 | OSC2/CLKOUT — Oscillator crystal output / clock output |
| 핀 16 | VDD — Positive supply voltage |
| 핀 17 | VSS — Ground reference |
| 핀 18 | RA0/AN0 — I/O port A bit 0 / Analog input channel 0 |
| 핀 19 | RA1/AN1 — I/O port A bit 1 / Analog input channel 1 |
| 핀 20 | RA2/AN2/VREF- — I/O port A bit 2 / Analog input channel 2 / ADC VREF- |
| 핀 21 | RA3/AN3/VREF+ — I/O port A bit 3 / Analog input channel 3 / ADC VREF+ |
| 핀 22 | RA4/T0CKI — I/O port A bit 4 / Timer0 clock input |
| 핀 23 | RA5/AN4/SS — I/O port A bit 5 / Analog input channel 4 / SPI slave select |
| 핀 24 | RB0/INT0 — I/O port B bit 0 / External interrupt 0 |
| 핀 25 | RB1/INT1 — I/O port B bit 1 / External interrupt 1 |
| 핀 26 | RB2/INT2 — I/O port B bit 2 / External interrupt 2 |
| 핀 27 | RB3/INT3 — I/O port B bit 3 / External interrupt 3 |
| 핀 28 | RB4 — I/O port B bit 4 |
| 핀 29 | RB5 — I/O port B bit 5 |
| 핀 30 | RB6/PGC — I/O port B bit 6 / In-circuit debugger clock |
| 핀 31 | RB7/PGD — I/O port B bit 7 / In-circuit debugger data |
| 핀 32 | VDD — Positive supply voltage |
| 핀 33 | VSS — Ground reference |
| 핀 34 | RC0/T1OSO/T1CKI — I/O port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| 핀 35 | RC1/T1OSI/CCP2 — I/O port C bit 1 / Timer1 oscillator input / CCP2 |
| 핀 36 | RC2/CCP1 — I/O port C bit 2 / CCP1 PWM output |
| 핀 37 | RC3/SCK/SCL — I/O port C bit 3 / SPI SCK / I2C SCL |
| 핀 38 | RD4/PSP4 — I/O port D bit 4 / Parallel Slave Port bit 4 |
| 핀 39 | RD5/PSP5 — I/O port D bit 5 / Parallel Slave Port bit 5 |
| 핀 40 | RD6/PSP6 — I/O port D bit 6 / Parallel Slave Port bit 6 |
| 핀 41 | RD7/PSP7 — I/O port D bit 7 / Parallel Slave Port bit 7 |
| 핀 42 | RE0/RD/AN5 — I/O port E bit 0 / Parallel Slave Port read / Analog input channel 5 |
| 핀 43 | RE1/WR/AN6 — I/O port E bit 1 / Parallel Slave Port write / Analog input channel 6 |
| 핀 44 | RE2/CS/AN7 — I/O port E bit 2 / Parallel Slave Port chip select / Analog input channel 7 |
| 핀 45 | CANTX — CAN bus transmit output |
| 핀 46 | CANRX — CAN bus receive input |
| 핀 47 | AVDD — Analog positive supply voltage |
| 핀 48 | AVSS — Analog ground reference |
| 핀 49 | MCLR/VPP — Master clear reset / programming voltage input |
| 핀 50 | NC — Not connected (per datasheet) |
| 핀 51 | NC — Not connected (per datasheet) |
| 핀 52 | NC — Not connected (per datasheet) |
| 핀 53 | NC — Not connected (per datasheet) |
| 핀 54 | NC — Not connected (per datasheet) |
| 핀 55 | NC — Not connected (per datasheet) |
| 핀 56 | NC — Not connected (per datasheet) |
| 핀 57 | NC — Not connected (per datasheet) |
| 핀 58 | NC — Not connected (per datasheet) |
| 핀 59 | NC — Not connected (per datasheet) |
| 핀 60 | NC — Not connected (per datasheet) |
| 핀 61 | NC — Not connected (per datasheet) |
| 핀 62 | NC — Not connected (per datasheet) |
| 핀 63 | NC — Not connected (per datasheet) |
| 핀 64 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
PIC18C658-E/PT 적합 용도: 6 애플리케이션s: Automotive CAN Body Control Modules, Industrial CAN Network Nodes, CAN-to-UART Protocol Gateways, HVAC Control Modules, Sensor Interface Modules, Embedded Automotive Lighting Controllers.
Automotive CAN Body Control Modules
The PIC18C658-E/PT is well-suited for automotive body control modules because its integrated CAN 2.0B peripheral enables direct connection to a vehicle CAN bus without an external controller. The 40 MHz / 10 MIPS throughput provides adequate headroom for body-control task scheduling such as door lock coordination, lighting control, and mirror adjustment. The -40C to +125C extended temperature rating meets automotive under-hood and cabin thermal requirements. Designers typically place the MCU between a 5V automotive regulator and the CAN transceiver (such as MCP2551), with the OTP program memory providing low per-unit cost in high-volume production runs.
추천
Industrial CAN Network Nodes
In industrial automation networks, the PIC18C658-E/PT serves as a CAN node controller interfacing sensors and actuators to a factory-wide CAN bus. The 32KB OTP program memory is sufficient for protocol stacks, sensor linearization, and diagnostic logging in fixed-function industrial nodes. The device's 10-bit ADC supports direct connection to analog sensors (temperature, pressure, level) without external signal conditioning. Engineers typically pair this MCU with isolated CAN transceivers and 24V-to-5V DC-DC converters, with the extended temperature range supporting deployment near motors and process equipment.
추천
CAN-to-UART Protocol Gateways
The PIC18C658-E/PT is appropriate for CAN-to-UART bridge gateways that translate messages between automotive/industrial CAN networks and legacy RS-232/RS-485 serial devices. Its integrated CAN 2.0B module plus hardware USART provide both bus interfaces natively without external protocol converters, reducing BOM cost and board area. The 40 MHz CPU can handle bidirectional message buffering, filtering, and protocol translation at typical automotive bus loads. Typical placement is between a CAN transceiver on one side and a MAX232/MAX485 RS-232/485 transceiver on the other, with the OTP memory locking in the gateway firmware once validated.
추천
HVAC Control Modules
The PIC18C658-E/PT fits HVAC (heating, ventilation, air conditioning) control modules that need robust networking, sensor integration, and reliable operation across temperature extremes. The integrated CAN module enables communication with a building automation backbone, while the 10-bit ADC handles temperature, humidity, and pressure sensor inputs. The -40C to +125C operating range supports both rooftop and indoor cabinet installations. Engineers typically pair this MCU with solid-state relay drivers for compressor/fan control and with EEPROM for non-volatile setpoint storage.
추천
Sensor Interface Modules
The PIC18C658-E/PT works well in distributed sensor interface modules that aggregate analog and digital sensor data and report over CAN to a central controller. The 10-bit ADC plus multiple timers and digital I/O accommodate diverse sensor types including thermistors, RTDs, flow meters, and digital encoders. The 32KB program memory holds sensor linearization tables and CAN communication stacks for fixed-function sensor nodes. Typical placement is on a small PCB near the sensor cluster with the MCU digitizing signals locally and transmitting processed values over CAN.
추천
Embedded Automotive Lighting Controllers
The PIC18C658-E/PT suits embedded automotive lighting controllers that drive exterior and interior lamp loads via MOSFET drivers while communicating over CAN. The 40 MHz CPU provides fast PWM generation for fade-in/fade-out lighting effects, and the CAN interface allows body control modules to command headlamp, signal, and ambient lighting functions. The extended -40C to +125C temperature range ensures operation in the harsh automotive underhood and cabin environments. Designers pair this MCU with high-side MOSFET drivers and CAN transceivers, using OTP memory to lock in validated lighting firmware.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18C658-E/PT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F6585-I/PT | PIC18F8680-I/PT | PIC18C658T-E/PT | PIC18F4585-I/PT | PIC18F46J50-I/PT |
|---|---|---|---|---|---|---|
| Package | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | 8-bit PIC18C RISC | 8-bit PIC18F RISC (flash) | 8-bit PIC18F RISC (flash) | 8-bit PIC18C RISC (OTP, T&R) | 8-bit PIC18F RISC (flash) | 8-bit PIC18F RISC (flash) |
| Program Memory | 32 KB OTP | 48 KB Flash | 32 KB Flash | 32 KB OTP | 48 KB Flash | 64 KB Flash |
| Maximum Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 48 MHz |
| Operating Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 3.3 V (PIC18F46J50 is 3.3V-only) |
| In-System Programmable | No (OTP) | Yes (Flash) | Yes (Flash) | No (OTP) | Yes (Flash) | Yes (Flash) |
| CAN Module | Yes (CAN 2.0B) | Yes (CAN 2.0B, enhanced) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B) | Yes (CAN 2.0B + USB 2.0) |
| Operating Temperature | -40C to +125C | -40C to +85C (I) / -40C to +125C (E) | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
| Lifecycle Status | Obsolete | Active | Active | Obsolete | Active | Active |
주요 차별점
- Integrated CAN 2.0B module eliminates external CAN controller (vs PIC18F4585-I/PT (similar flash MCU))
- Extended -40C to +125C temperature grade as standard (vs PIC18F46J50-I/PT (industrial 85C))
- Obsolete legacy status with clear modern replacement path (vs Active PIC18F6585-I/PT)
설계 노트
The PIC18C658-E/PT uses OTP (One-Time Programmable) memory, which cannot be erased or reprogrammed. Every firmware revision in development requires a new physical part, which is costly and slow. For new designs, Microchip recommends the flash-based PIC18F6585-I/PT drop-in replacement - it uses the same TQFP-64 (10x10) footprint but supports in-system programming via ICSP, allowing rapid iteration and field firmware updates. Estimate: switching to PIC18F6585 typically saves 30-50% on development cost for products with multiple firmware revisions.
The PIC18C658-E/PT operates from a single 5V supply and requires proper decoupling for reliable CAN communication. Place a 100 nF ceramic decoupling capacitor as close as possible to each VDD pin, plus a 10 uF bulk capacitor near the IC. The AVdd and AVss pins power the ADC; isolate them with a ferrite bead or small inductor from the digital VDD rail, and add a 100 nF + 10 uF capacitor pair at the AVdd pin for low-noise ADC reference operation. Without proper decoupling, the CAN module may experience bit errors at high bus loads.
At 40 MHz operation the PIC18C658-E/PT dissipates approximately 50-75 mW depending on I/O loading and peripheral activity. The TQFP-64 (10x10) package has a thermal resistance (theta_JA) of approximately 50 C/W on a standard 4-layer JEDEC test board, giving a junction temperature rise of 3-4 C above ambient - well within the -40C to +125C operating range. No heatsink is required for normal operation. However, in enclosed enclosures without airflow, ensure ambient temperature stays below +120C to maintain the 5 C margin to maximum junction temperature.
For reliable CAN bus communication, route the CANTX and CANRX signals as a short differential pair to the CAN transceiver (such as MCP2551), keeping traces under 50 mm to minimize EMI susceptibility. Place the transceiver close to the bus connector with a common-mode choke and ESD protection diodes. The MCU's crystal oscillator (OSC1/OSC2) traces should be short and symmetric, with the crystal placed within 10 mm of the MCU and guard ground traces around them to reduce radiated emissions. Place all decoupling capacitors on the same PCB layer as the MCU, with vias direct to the ground plane.
규정 준수 정보
RoHS compliance per distributor data. AEC-Q100 not qualified - the E suffix indicates Extended temperature grade, not automotive qualification. For AEC-Q100 qualified alternatives, consider PIC18F6585-I/PT automotive variants.
