PIC18LF46K80-I/PT - 8-bit 64MHz 64KB Flash XLP MCU w/ ECAN | Microchip
MPN: PIC18LF46K80-I/PT ✓ AktifPIC18LF46K80-I/PT Ringkasan
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals around an 8-bit data path. The PIC18 family uses an enhanced RISC Harvard design with a 16-bit instruction word and 8-bit data path, belonging to the broader category of microcontrollers -> embedded processors -> semiconductors. The 'LF' prefix indicates a low-voltage variant supporting 1.8V-3.6V operation with extended XLP sleep currents below 100 nA typical, while 'F' (non-LF) variants support 1.8V-5.5V. The 'K80' sub-family adds integrated ECAN (CAN 2.0B active), CTMU (Charge Time Measurement Unit) for mTouch capacitive sensing, and 12-bit ADC with up to 12 channels.
Key specifications include 35 I/O pins, 12-bit ADC resolution, two UART/USART modules, one I2C, one SPI, and seven 10-bit PWM outputs. The device operates across -40C to +85C (industrial 'I' temperature grade) at 1.8V to 3.6V supply. It features nanoWatt XLP technology with typical sleep currents of <100 nA and Run currents of approximately 7 mA at 4 MHz. The CTMU peripheral enables capacitive touch buttons, sliders, and proximity sensing without external components.
The architecture uses a 2-stage pipeline with single-cycle instruction execution at 64MHz (16 MIPS), a hardware multiplier, C-compiler-optimized instruction set, and a priority-level interrupt controller. The 64KB Flash is self-programmable under firmware control (ICSP) and supports bootloader operation. ECAN supports CAN 2.0B active with hardware acceptance filters, providing automotive-grade bus connectivity.
Typical applications include industrial CAN nodes, automotive body and comfort modules, building automation, capacitive touch human-machine interfaces, sensor hubs with analog front-ends, and low-power remote battery-powered monitoring. The integrated ECAN and XLP make it particularly suited for sleep-dominated networks such as automotive LIN/CAN gateways and HVAC controllers.
Design consideration: when migrating between 'LF' (1.8V-3.6V) and 'F' (1.8V-5.5V) variants, verify that any 5V peripherals are tolerant of the lower VDD. ECAN bus termination (120 ohm) must be placed at each end of the bus segment. For CTMU touch sensing, PCB layout guidelines from Microchip AN1250 should be followed.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternatif penggantian untuk PIC18LF46K80-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC18LF46K80-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam ADC, Package, Comparators, Communication, Core Architecture.
PIC18F46K80-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18F46K80-E/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18LF45K80-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF46K42-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF46K40-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF46K80-I/PT Rating Maksimal & Karakteristik Listrik
| Core Architecture | PIC18 (8-bit enhanced RISC) |
| Frekuensi Bawah Maximum | 64 MHz |
| Instruction Throughput | 16 MIPS |
| Program Memory (Flash) | 64 KB (32K x 16) |
| Data RAM | 3.56 KB |
| Data EEPROM | 1 KB (1024 bytes) |
| Operating Voltage Range | 1.8 V to 3.6 V (LF variant) |
| I/O Pins | 35 |
| ADC | 12-bit, up to 11 channels |
| PWM Outputs | 7 channels (10-bit) |
| Communication | ECAN, 2x UART, 1x I2C, 1x SPI |
| Special Features | ECAN 2.0B Active, CTMU (mTouch), nanoWatt XLP |
| Suhu Kerja | -40 C to +85 C (Industrial -I) |
| Paket | TQFP-44 (10x10x1 mm) |
| Tipe Mounting | Surface Mount |
| Level MSL | 3 |
| Status RoHS | Compliant |
| Lead-Free | Yes |
Konfigurasi Pin PIC18LF46K80-I/PT
| Pin produk 1 | RB5/AN11/C2INB — PORTB bit 5 / ADC ch11 / Comparator C2 input B |
| Pin produk 2 | RB4/AN10/C2INA — PORTB bit 4 / ADC ch10 / Comparator C2 input A |
| Pin produk 3 | RB3/AN9/CTMUI/C1INA — PORTB bit 3 / ADC ch9 / CTMU input / Comparator C1 input A |
| Pin produk 4 | RB2/AN8/CTMUE — PORTB bit 2 / ADC ch8 / CTMU edge |
| Pin produk 5 | RB1/AN7/CTMUN — PORTB bit 1 / ADC ch7 / CTMU negative |
| Pin produk 6 | RB0/AN6/CTMUP — PORTB bit 0 / ADC ch6 / CTMU positive |
| Pin produk 7 | VDD — Positive supply voltage (1.8V-3.6V) |
| Pin produk 8 | VSS — Ground reference |
| Pin produk 9 | RD7/ECANRX — PORTD bit 7 / ECAN RX |
| Pin produk 10 | RD6/ECANTX — PORTD bit 6 / ECAN TX |
| Pin produk 11 | RC7/AN12/C2OUT — PORTC bit 7 / ADC ch12 / Comparator C2 output |
| Pin produk 12 | RC6/AN11/C1OUT — PORTC bit 6 / ADC ch11 / Comparator C1 output |
| Pin produk 13 | RC5/C2INB — PORTC bit 5 / Comparator C2 input B |
| Pin produk 14 | RC4/C2INA — PORTC bit 4 / Comparator C2 input A |
| Pin produk 15 | RC3/SCL1 — PORTC bit 3 / I2C1 SCL |
| Pin produk 16 | RC2/SDA1 — PORTC bit 2 / I2C1 SDA |
| Pin produk 17 | RC1/CCP8 — PORTC bit 1 / PWM output 8 |
| Pin produk 18 | RC0/SOSCO — PORTC bit 0 / Secondary oscillator output |
| Pin produk 19 | OSC2/RA6 — Crystal oscillator output / PORTA bit 6 |
| Pin produk 20 | OSC1/RA7 — Crystal oscillator input / PORTA bit 7 |
| Pin produk 21 | RA0/AN0/C1INA — PORTA bit 0 / ADC ch0 / Comparator C1 input A |
| Pin produk 22 | RA1/AN1/C1INB — PORTA bit 1 / ADC ch1 / Comparator C1 input B |
| Pin produk 23 | RA2/AN2/C2INA — PORTA bit 2 / ADC ch2 / Comparator C2 input A |
| Pin produk 24 | RA3/AN3/C2INB — PORTA bit 3 / ADC ch3 / Comparator C2 input B |
| Pin produk 25 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pin produk 26 | RA5/AN4 — PORTA bit 5 / ADC ch4 |
| Pin produk 27 | VSS — Ground reference |
| Pin produk 28 | VDD — Positive supply voltage (1.8V-3.6V) |
| Pin produk 29 | RB7/AN13 — PORTB bit 7 / ADC ch13 |
| Pin produk 30 | RB6/AN12 — PORTB bit 6 / ADC ch12 |
| Pin produk 31 | RE3/MCLR — PORTE bit 3 / Master Clear (reset) |
| Pin produk 32 | RE2/CCP10 — PORTE bit 2 / PWM output 10 |
| Pin produk 33 | RE1/CCP9 — PORTE bit 1 / PWM output 9 |
| Pin produk 34 | RE0/CCP8 — PORTE bit 0 / PWM output 8 |
| Pin produk 35 | RD0/C1INA — PORTD bit 0 / Comparator C1 input A |
| Pin produk 36 | RD1/C1INB — PORTD bit 1 / Comparator C1 input B |
| Pin produk 37 | RD2/C2INA — PORTD bit 2 / Comparator C2 input A |
| Pin produk 38 | RD3/C2INB — PORTD bit 3 / Comparator C2 input B |
| Pin produk 39 | RD4 — PORTD bit 4 |
| Pin produk 40 | RD5 — PORTD bit 5 |
| Pin produk 41 | VSS — Ground reference |
| Pin produk 42 | VDDCORE — Core voltage regulator output (decoupling required) |
| Pin produk 43 | RC8/CCP2 — PORTC bit 8 / PWM output 2 |
| Pin produk 44 | RC6 — PORTC bit 6 (alt) |
Aplikasi Umum
PIC18LF46K80-I/PT cocok untuk 6 aplikasis: Industrial CAN Node, Automotive Body & Comfort Module, Capacitive Touch HMI (mTouch), Battery-Powered Sensor Hub, Building Automation Controller, Industrial Sensor Transmitter (4-20mA).
Industrial CAN Node
The PIC18LF46K80-I/PT's integrated ECAN 2.0B active peripheral with hardware acceptance filters and timestamping makes it ideal for industrial CAN node applications. The 16 MIPS CPU throughput handles CANopen or DeviceNet stack processing alongside sensor polling, while 3.56KB RAM accommodates CAN message buffers. At 64MHz with 1.8V-3.6V VDD, the device sustains real-time bus response under load. The ECAN module supports bit rates up to 1 Mbps, matching CiA 301 CANopen requirements; nanoWatt XLP enables sleep current under 100 nA typical, allowing battery-backed nodes to wake on CAN bus activity.
Direkomendasikan
Automotive Body & Comfort Module
The PIC18LF46K80-I/PT (industrial grade) is widely deployed in automotive body controllers for window lifters, seat controllers, mirror modules, and interior lighting. Its 35 I/O pins directly drive relays, LEDs, and H-bridge MOSFETs, while 12-bit ADC reads position sensors and current shunt monitors. CTMU enables touch-sensitive door handles and proximity switches without external ICs. For AEC-Q100-grade designs, the PIC18F46K80-E/PT variant extends the temperature range to +125C. LIN bus via UART and ECAN provides dual-network flexibility.
Direkomendasikan
Capacitive Touch HMI (mTouch)
The PIC18LF46K80-I/PT's integrated CTMU (Charge Time Measurement Unit) supports Microchip's mTouch capacitive touch library, enabling buttons, sliders, proximity sensors, and water-tolerant touch panels. CTMU measures capacitance to femtofarad resolution using charge time pulses, eliminating external analog components. Combined with 12-bit ADC for force/temperature compensation, the device delivers robust touch HMI in appliances, industrial controls, and consumer products. The 64MHz core handles touch scanning of 16+ electrodes at >100Hz refresh rate.
Direkomendasikan
Battery-Powered Sensor Hub
The PIC18LF46K80-I/PT's nanoWatt XLP technology enables sensor hub designs that run for years on a single battery. Sleep current is below 100 nA typical with RTCC and watchdog active, and Run current is approximately 7 mA at 4 MHz / 2V. The 12-bit ADC reads temperature, humidity, and analog sensors, while I2C/SPI interfaces digital sensors. With 64KB Flash, designers can implement application logic, calibration tables, and BLE/Sigfox wake-up sequencing. The 1.8V-3.6V VDD range is ideal for 2xAA or Li-primary cells.
Direkomendasikan
Building Automation Controller
The PIC18LF46K80-I/PT suits HVAC controllers, smart thermostats, and BACnet/LonWorks node applications. ECAN or UART-based protocol stacks run on the 16 MIPS core; 64KB Flash stores BACnet object dictionaries and scheduling logic. CTMU supports touch-panel interfaces, and 12-bit ADC reads thermistor/thermocouple inputs via external front-end. With 35 I/O and PWM outputs, the device directly drives triacs, optocouplers, and LCD modules. Sleep current below 100 nA suits battery-backed thermostat designs.
Direkomendasikan
Industrial Sensor Transmitter (4-20mA)
In 4-20mA loop-powered sensor transmitters, the PIC18LF46K80-I/PT's low-voltage operation (1.8V-3.6V) and 7 mA typical Run current at 4 MHz enable designs powered entirely from the loop with a 3.3V LDO. The 12-bit ADC achieves 0.024% FS accuracy for process-variable measurement, and the ECAN/UART enables HART modem communication via external AD5700. Sleep current below 100 nA supports multi-year battery backup. The CTMU can detect broken-sensor or open-loop conditions for diagnostic reporting.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC18LF46K80-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC18F46K80-I/PT | PIC18F46K80-E/PT | PIC18LF46K42-I/PT | PIC18LF46K40-I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-44 | TQFP-44 (same) | TQFP-44 (same) | TQFP-44 (same) | TQFP-44 (same) |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C (AEC-Q100) | -40 C to +85 C | -40 C to +85 C |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| ECAN | Yes (2.0B Active) | Yes (2.0B Active) | Yes (2.0B Active) | Yes (with CIP) | No |
| CTMU (mTouch) | Yes | Yes | Yes | Yes (improved) | No |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit (faster) | 10-bit |
| Typical 1k-piece Price (USD) | 3.74 | 3.74 (approx) | 4.20 (approx) | 2.95 (approx) | 2.50 (approx) |
Diferensiator Kunci
- Integrated ECAN 2.0B Active peripheral (vsPIC18LF46K40-I/PT)
- CTMU mTouch capacitive sensing (vsPIC18LF46K40-I/PT)
- Lower-voltage XLP nanoWatt operation (vsPIC18F46K80-I/PT)
Catatan Desain
The PIC18LF46K80-I/PT operates from 1.8V to 3.6V (LF variant). When migrating from F (1.8V-5.5V) to LF, verify that 5V-tolerant peripherals are connected through proper level shifters. Place 100nF and 10uF decoupling capacitors as close as possible to VDD/VSS pairs (pins 7/8 and 28/27). Add a 100nF on VDDCORE (pin 42) for the internal voltage regulator. Estimated: at 4 MHz / 3.3V active mode, current draw is approximately 7 mA; sleep current below 100 nA.
For ECAN designs, the CANH and CANL traces must be routed as a differential pair with 120 ohm characteristic impedance, matching the bus termination. Place MCP2551 (or equivalent 3.3V CAN transceiver) within 50 mm of the MCU's CANTX/CANRX pins (RD6/RD7) to minimize EMI. Keep CAN bus traces away from switching power and clock lines. Reference: Microchip AN228 - CAN Physical Layer Design.
Critical pitfalls: (1) The CTMU peripheral requires a 1 ms stabilization delay after enabling before accurate capacitance readings. (2) The 'LF' low-voltage part CANNOT be used at 5V VDD - check for accidental 5V supply. (3) ICSP programming requires the PGD/PGC pins to be 5V-tolerant only in the F variant; on LF, voltage above VDD on PGD/PGC may damage the MCU. (4) MCLR must be tied to VDD through a 10k resistor for normal operation; do not leave floating.
Informasi Konformitas
Industrial temperature grade (-40C to +85C); not AEC-Q100 qualified - select PIC18F46K80-E/PT for automotive. RoHS and lead-free per Microchip product page.
