PIC18LF46K80T-I/PT - 8-bit 64MHz 64KB Flash MCU w/ECAN XLP
MPN: PIC18LF46K80T-I/PT ✓ AktifPIC18LF46K80T-I/PT Ringkasan
An 8-bit PIC microcontroller is a RISC-architecture MCU built around a 16-bit instruction word, providing deterministic execution timing and rich peripheral integration for cost-sensitive embedded designs. PIC18LF devices sit at the top of the 8-bit PIC family, adding large linear RAM, hardware ECAN/USB stacks, and nanoWatt XLP™ sleep modes that push active current down to the single-digit mA range and sleep current to the sub-microamp range. Within the broader semiconductor hierarchy, PIC MCUs belong to the microcontroller family, which itself sits inside the embedded system category of integrated circuits.
Key features include a 12-bit A/D converter with up to 12 channels, a CTMU (Charge Time Measurement Unit) for capacitive touch sensing, four 16-bit timers, two CCP/ECCP modules, two MSSP (I²C/SPI) ports, two ECAN modules, two comparators, and 35 general-purpose I/O pins. The device supports LIN, SPI, I²C, and CAN connectivity, plus a 4 KB EEPROM for non-volatile data storage. The nanoWatt XLP™ feature delivers an ultra-low standby current profile for energy-harvesting and IoT battery designs.
Architecturally, the PIC18LF46K80 uses a Harvard-style RISC core with hardware multiply and a 31-level stack, providing predictable interrupt latency and deterministic real-time control. Its ECAN™ peripheral supports CAN 2.0B with acceptance filters, making it a strong fit for automotive body and industrial networks. The integrated CTMU simplifies touch-button and capacitive-proximity interfaces without an external analogue front end.
Typical applications include CAN node endpoints, automotive body controllers, sensor nodes, industrial control panels, and low-power IoT endpoints. The wide -40 °C to +85 °C industrial temperature range, combined with the low-voltage operating window, makes this part a strong fit for any 3.3V system requiring robust connectivity and ultra-low standby power.
When designing with this device, ensure the supply stays within 1.8V to 3.6V (LF variant) and that the ECAN bus is terminated with 120 Ω at each end. For sleep-mode current to reach the datasheet minimum, the MCLR pull-up and unused I/O lines must be configured to avoid parasitic current paths.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers an actionable one-stop reference for the PIC18LF46K80T-I/PT.
Alternatif penggantian untuk PIC18LF46K80T-I/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC18LF46K80T-I/PT (sama faktor bentuk dan footprint) — berbeda di dalam Package, ADC, Operating Temperature, Core Architecture, I/O Pins.
PIC18F46K80T-I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18LF46K80-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF45K80T-I/ML
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF46K80T-I/ML
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC18LF26K80T-I/SO
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF46K40-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC18LF46K80T-I/PT Rating Maksimal & Karakteristik Listrik
| Core Processor | PIC |
| Core Size | 8-bit |
| Program Memory Size | 64 KB (32K x 16) FLASH |
| RAM Size | 3.6 KB (3.6K x 8) |
| EEPROM Size | 1 KB |
| Maximum CPU Speed | 64 MHz (16 MIPS) |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Number of I/O | 35 |
| ADC | 12-bit, up to 12 channels |
| Comparators | 2 |
| Timers (16-bit) | 4 |
| CCP / ECCP Modules | 2 |
| MSSP (I²C/SPI) Ports | 2 |
| ECAN Modules | 2 (CAN 2.0B) |
| CTMU (Touch Sensing) | Yes |
| Connectivity | ECAN, I²C, LIN, SPI, UART |
| Rentang Suhu Kerja | -40 °C to +85 °C (Industrial) |
| Paket | 44-pin TQFP (10x10 mm) |
| Tipe Mounting | Surface Mount |
| Packaging | Tape & Reel |
| Status RoHS | Compliant |
Konfigurasi Pin PIC18LF46K80T-I/PT
| Pin produk 1 | RC7/RX1/DT1/CCP4/MA1 — I/O port C bit 7 / EUSART1 RX / CCP4 |
| Pin produk 2 | RC6/TX1/CK1/CCP3 — I/O port C bit 6 / EUSART1 TX / CCP3 |
| Pin produk 3 | RC5/D+/VP — I/O port C bit 5 / USB D+ or ADC reference |
| Pin produk 4 | RC4/D-/VM — I/O port C bit 4 / USB D- or ADC reference |
| Pin produk 5 | RC3/SCL/SCK1/SDA1/MA2 — I/O port C bit 3 / I²C/SPI clock |
| Pin produk 6 | RC2/SDA1/SDI1/MA3 — I/O port C bit 2 / I²C/SPI data |
| Pin produk 7 | RC1/SOSI/CCP2 — I/O port C bit 1 / SOSI / CCP2 |
| Pin produk 8 | RC0/SOSO — I/O port C bit 0 / SOSO |
| Pin produk 9 | OSC1/RA7 — Crystal oscillator input / GPIO RA7 |
| Pin produk 10 | OSC2/RA6 — Crystal oscillator output / GPIO RA6 |
| Pin produk 11 | RA5/AN4/C2INA — I/O port A bit 5 / ADC ch4 |
| Pin produk 12 | RA4/AN3/C1INA — I/O port A bit 4 / ADC ch3 |
| Pin produk 13 | RA3/AN2/Vref+ — I/O port A bit 3 / ADC ch2 / Vref+ |
| Pin produk 14 | RA2/AN1/Vref- — I/O port A bit 2 / ADC ch1 / Vref- |
| Pin produk 15 | RA1/AN0/C1INC — I/O port A bit 1 / ADC ch0 |
| Pin produk 16 | RA0/AN0 — I/O port A bit 0 |
| Pin produk 17 | VSS — Ground |
| Pin produk 18 | VDD — Positive supply (1.8V–3.6V) |
| Pin produk 19 | RB7/KBI3/PGD — I/O port B bit 7 / ICD data |
| Pin produk 20 | RB6/KBI2/PGC — I/O port B bit 6 / ICD clock |
| Pin produk 21 | RB5/KBI1/AN13/C1INA — I/O port B bit 5 / ADC ch13 |
| Pin produk 22 | RB4/KBI0/AN11/C2INA — I/O port B bit 4 / ADC ch11 |
| Pin produk 23 | RB3/AN9/C1OUT — I/O port B bit 3 / ADC ch9 |
| Pin produk 24 | RB2/AN8/C2OUT — I/O port B bit 2 / ADC ch8 |
| Pin produk 25 | RB1/AN10/C1OUT — I/O port B bit 1 / ADC ch10 |
| Pin produk 26 | RB0/AN12 — I/O port B bit 0 / ADC ch12 |
| Pin produk 27 | VSS — Ground |
| Pin produk 28 | VDD — Positive supply (1.8V–3.6V) |
| Pin produk 29 | RD7/PSP7/MA1 — I/O port D bit 7 / Parallel Slave Port |
| Pin produk 30 | RD6/PSP6 — I/O port D bit 6 / Parallel Slave Port |
| Pin produk 31 | RD5/PSP5 — I/O port D bit 5 / Parallel Slave Port |
| Pin produk 32 | RD4/PSP4 — I/O port D bit 4 / Parallel Slave Port |
| Pin produk 33 | RD3/PSP3 — I/O port D bit 3 / Parallel Slave Port |
| Pin produk 34 | RD2/PSP2/CANTX — I/O port D bit 2 / ECAN TX |
| Pin produk 35 | RD1/PSP1/C1RX — I/O port D bit 1 / ECAN RX |
| Pin produk 36 | RD0/PSP0/C2RX — I/O port D bit 0 / ECAN RX |
| Pin produk 37 | RE3/MCLR/VPP — Master Clear (reset) / programming voltage |
| Pin produk 38 | RE2/CS — I/O port E bit 2 / Chip Select |
| Pin produk 39 | RE1/WR — I/O port E bit 1 / Write strobe |
| Pin produk 40 | RE0/RD — I/O port E bit 0 / Read strobe |
| Pin produk 41 | RE7/ECCP2/P2A — I/O port E bit 7 / ECCP2 channel A |
| Pin produk 42 | RE6/ECCP1/P1A — I/O port E bit 6 / ECCP1 channel A |
| Pin produk 43 | RE5 — I/O port E bit 5 |
| Pin produk 44 | RE4 — I/O port E bit 4 |
Aplikasi Umum
PIC18LF46K80T-I/PT cocok untuk 6 aplikasis: Automotive CAN Node, Industrial Sensor Node, Capacitive Touch Interface, Battery-Powered IoT Endpoint, Home Appliance Control Board, Portable Medical Monitor.
Automotive CAN Node
The PIC18LF46K80T-I/PT fits automotive CAN nodes because its two integrated ECAN™ modules implement CAN 2.0B with acceptance filters, eliminating the need for an external CAN controller. With 64 KB flash, 3.6 KB RAM, and 1.8V–3.6V supply, it handles OBD-II firmware, J1939 stacks, and gateway tasks while staying within automotive power budgets. Pair with an MCP2551 or MCP2562 CAN transceiver; the LF variant operates on a 3.3V rail common in body-electronics modules.
Direkomendasikan
Industrial Sensor Node
In industrial sensor nodes the PIC18LF46K80T-I/PT serves as the local controller and protocol translator. Its 12-bit ADC with up to 12 channels handles multi-sensor scanning (temperature, pressure, current) while the ECAN module reports back to a PLC. The 64 MHz CPU executes J1939 or CANopen stacks in real time. The industrial -40 °C to +85 °C temperature range and robust PIC18 XLP peripheral set suit factory-floor deployments.
Direkomendasikan
Capacitive Touch Interface
The PIC18LF46K80T-I/PT is well suited for capacitive touch interfaces thanks to the integrated CTMU (Charge Time Measurement Unit), which measures capacitance changes on a button or slider pad without an external analogue front end. With 64 KB flash and 35 GPIO, the same MCU runs the touch firmware, drives the LCD, and communicates via UART to a host controller. The 12-bit ADC supports proximity-sensor overlays and LED current sense.
Direkomendasikan
Battery-Powered IoT Endpoint
The PIC18LF46K80T-I/PT fits coin-cell and 2xAA IoT endpoints because the nanoWatt XLP™ sleep current drops to sub-microamp levels, and the 1.8V–3.6V supply accepts a CR2032 coin cell directly. With 64 KB flash and 3.6 KB RAM, the part handles BLE/Zigbee co-processor command parsing, sensor aggregation, and ECAN / LIN bus duty cycling. The integrated 12-bit ADC reads battery voltage for accurate SoC reporting.
Direkomendasikan
Home Appliance Control Board
White-goods and HVAC controllers benefit from the PIC18LF46K80T-I/PT's LIN bus connectivity for sensor/actuator networking, plus the ECAN port for higher-speed backbone links to the main board. The 35 GPIO drive relays, TRIACs, and status LEDs directly, and the 12-bit ADC reads thermistors and pressure transducers. The industrial temperature range covers under-cabinet and outdoor HVAC environments.
Direkomendasikan
Portable Medical Monitor
Portable medical devices such as pulse oximeters and glucose meters leverage the PIC18LF46K80T-I/PT's low-voltage operation, low sleep current, and 12-bit ADC for accurate sensor readout. The 64 KB flash stores reference curves and calibration tables, while the ECAN port enables secure wired connectivity to hospital networks. The wide operating temperature range and the LF variant's 1.8V minimum suit lithium-primary powered designs.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC18LF46K80T-I/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC18F46K80T-I/PT | PIC18LF46K80-I/PT | PIC18LF45K80T-I/ML | PIC18LF46K80T-I/ML | PIC18LF26K80T-I/SO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-44 (10x10) | TQFP-44 (10x10) - same | TQFP-44 (10x10) - same | QFN-44 (8x8) - variant | QFN-44 (8x8) - variant | SOIC-28 - smaller |
| Supply Voltage Range | 1.8V to 3.6V (LF) | 2.0V to 5.5V (F) | 1.8V to 3.6V (LF) | 1.8V to 3.6V (LF) | 1.8V to 3.6V (LF) | 1.8V to 3.6V (LF) |
| Program Flash | 64 KB | 64 KB | 64 KB | 32 KB | 64 KB | 64 KB |
| RAM | 3.6 KB | 3.6 KB | 3.6 KB | 2 KB | 3.6 KB | 3.6 KB |
| ECAN Modules | 2 | 2 | 2 | 2 | 2 | 1 |
| CPU Speed | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS |
| Packaging Format | Tape & Reel | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tape & Reel |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Diferensiator Kunci
- Integrated ECAN module (CAN 2.0B) eliminates external CAN controller (vsPIC18LF46K40-I/PT)
- Two ECAN modules enable CAN gateway or dual-bus architectures (vsPIC18LF26K80T-I/SO)
- CTMU peripheral simplifies capacitive touch firmware (vsPIC18LF46J11-I/ML)
Catatan Desain
For nanoWatt XLP™ sleep current to reach the datasheet minimum (sub-1 µA), unused peripherals must be disabled in the PMDx register and unused I/O configured as outputs driving low. The MCLR pull-up should be implemented as a 100 kΩ resistor or omitted in sleep-only designs to prevent parasitic current paths through the input protection diodes.
Keep the ECAN TX/RX traces short and matched to within 5 mm to comply with CAN 2.0B bus timing at 1 Mbps. Place a 120 Ω termination resistor at each end of the bus only, not on every node. The 44-pin TQFP-44 (10x10) package benefits from a continuous ground plane beneath the device to provide thermal dissipation and a low-impedance return path for ECAN and MSSP signals.
Do not exceed 3.6V VDD on the LF variant - operation above the absolute-maximum supply voltage will damage the part. If a 5V supply is unavoidable, choose the PIC18F46K80T-I/PT sibling instead. For ECAN loop-back tests, remember to put the microcontroller into Loopback mode by setting the CANCTRL.REQOP bits before connecting to an active bus, otherwise it will interfere with other nodes.
Estimated: At maximum 64 MHz CPU clock with all peripherals active, the PIC18LF46K80T-I/PT draws approximately 15 mA from a 3.3V supply, dissipating about 50 mW. The TQFP-44 (10x10) package has a typical theta_JA around 50 °C/W, giving a junction temperature rise of only 2.5 °C above ambient - no heatsink is required. Thermal management is dominated by I/O current, not core power.
Informasi Konformitas
RoHS and REACH compliance stated on Microchip product page. Not AEC-Q100 qualified - for automotive, see PIC18F46K80-I/PT family variants (separate AEC-Q100 versions exist in Microchip portfolio).