PIC24EP512GU810-E/PT - 60 MIPS 16-bit MCU, 512KB Flash, USB/CAN | Microchip
MPN: PIC24EP512GU810-E/PT ✓ AktifPIC24EP512GU810-E/PT Ringkasan
A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and configurable peripherals on one die. The PIC24E family extends this concept with a 16-bit modified Harvard architecture that executes most instructions in one cycle; in the system hierarchy it sits between simple 8-bit MCUs and 32-bit ARM Cortex-M devices. This part specifically belongs to the PIC24E general-purpose sub-family known for high-throughput DSP-friendly math, USB, and CAN connectivity.
Key features include 16-bit ADC with up to 12-bit conversion at 1.1 Msps, multiple 16-bit timers, nine 16-bit and eight 32-bit general-purpose timers for a total of 27 timer channels, PWM with high-resolution duty control, and dual ECAN modules compliant with CAN 2.0B. The device runs from 3.0V to 3.6V with on-chip LDO, supports -40C to +125C operating temperature, and is AEC-Q100 qualified for automotive applications.
The PIC24EP512GU810 uses Microchip's 16-bit modified Harvard architecture with DSP extensions, deterministic interrupt latency, and a wide peripheral set, enabling the same chip to drive motor control loops, run a USB stack, and bridge to CAN networks. The large 512 KB Flash supports over-the-air (OTA) bootloaders and dual-image schemes, while the 52 KB RAM accommodates USB HID/CDC class stacks plus communications buffers without external memory expansion.
Typical applications include industrial automation and motor control, automotive body and chassis ECUs, USB-CDC/HID peripherals, CAN-bridge gateways, and medical instrumentation. The wide I/O count makes it suitable for graphical HMI panels when paired with an external TFT controller. In each of these roles the part replaces a discrete MCU-plus-CAN/USB transceiver board with a single chip solution.
Design tip: route the USB D+/D- lines as a 90-ohm differential pair and place the 48 MHz crystal within 5 mm of the OSCI/OSCO pins. For CAN, use a 120-ohm termination resistor and isolate the bus from noisy switching nodes. The on-chip LDO requires a 1 uF + 10 uF decoupling network on VDDCORE.
This page synthesizes distributor pricing, same-brand drop-in alternatives, application notes, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, sourcing, and schematic-level decisions.
Alternatif penggantian untuk PIC24EP512GU810-E/PT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC24EP512GU810-E/PT (sama faktor bentuk dan footprint) — berbeda di dalam Package, Timers, ADC, Core, I/O Pins.
PIC24EP512GU810-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC24EP512GU810-E/PF
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PIC24EP256GU810-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →DSPIC33EP512MU810-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC24EP512GU810-E/PT Rating Maksimal & Karakteristik Listrik
| Product Type | 16-bit Microcontroller (MCU) |
| Series | PIC 24EP |
| Core Architecture | 16-bit modified Harvard with DSP |
| CPU Speed | 60 MIPS (70 MHz core) |
| Program Memory | 512 KB Flash (170K x 24) |
| RAM | 52 KB |
| Tegangan Pemuat | 3.0 V to 3.6 V |
| I/O Pins | 83 |
| Paket | 100-TQFP (12x12 mm, 1.10 mm height) |
| Communication | USB 2.0 Full-Speed, 2x CAN 2.0B, UART, SPI, I2C |
| ADC | Up to 12-bit, 1.1 Msps |
| Timers | 27 (9x 16-bit + 8x 32-bit) |
| PWM | High-resolution PWM outputs |
| Suhu Kerja | -40C to +125C (E = Enhanced, AEC-Q100 Grade) |
| Tipe Mounting | Surface Mount |
| Level MSL | 3 (per JEDEC J-STD-020, reflow 245C) |
| Status RoHS | Compliant |
| AEC-Q100 | Qualified (automotive grade) |
Konfigurasi Pin PIC24EP512GU810-E/PT
| Pin produk 1 | RP15/RB15 — Remappable I/O (PPS), Port B |
| Pin produk 2 | RP14/RB14 — Remappable I/O (PPS), Port B |
| Pin produk 3 | VSS — Ground reference |
| Pin produk 4 | VDD — Power supply 3.0-3.6 V |
| Pin produk 5 | RP13/USBID/RB13 — Remappable I/O / USB ID detect |
| Pin produk 6 | RB12/RP12 — Remappable I/O, Port B |
| Pin produk 7 | D- — USB D- differential data |
| Pin produk 8 | D+ — USB D+ differential data |
| Pin produk 9 | VBUS — USB VBUS detect |
| Pin produk 10 | RP11/RB11 — Remappable I/O, Port B |
| Pin produk 11 | VDD — Power supply 3.0-3.6 V |
| Pin produk 12 | VSS — Ground reference |
| Pin produk 13 | OC1/RD0 — Output Compare 1 / PWM |
| Pin produk 14 | OC2/RD1 — Output Compare 2 / PWM |
| Pin produk 15 | RD2 — Port D I/O |
| Pin produk 16 | RD3 — Port D I/O |
| Pin produk 17 | RD4 — Port D I/O |
| Pin produk 18 | RD5 — Port D I/O |
| Pin produk 19 | VDDCORE — Internal LDO output, decouple with 1uF+10uF |
| Pin produk 20 | ENVREG — Enable internal LDO regulator |
| Pin produk 21 | RA0 — Port A I/O / analog input |
| Pin produk 22 | RA1 — Port A I/O / analog input |
| Pin produk 23 | RA2 — Port A I/O / analog input |
| Pin produk 24 | RA3 — Port A I/O / analog input |
| Pin produk 25 | RA4 — Port A I/O / analog input |
| Pin produk 26 | RA5 — Port A I/O / analog input |
| Pin produk 27 | RA6 — Port A I/O / analog input |
| Pin produk 28 | VDD — Power supply 3.0-3.6 V |
| Pin produk 29 | VSS — Ground reference |
| Pin produk 30 | RA7 — Port A I/O / analog input |
| Pin produk 31 | RA8 — Port A I/O / analog input |
| Pin produk 32 | RA9 — Port A I/O / analog input |
| Pin produk 33 | RA10 — Port A I/O / analog input |
| Pin produk 34 | VREF+ — ADC voltage reference positive |
| Pin produk 35 | VREF- — ADC voltage reference negative |
| Pin produk 36 | AVDD — Analog supply 3.0-3.6 V |
| Pin produk 37 | AVSS — Analog ground |
| Pin produk 38 | RB0/PGED3 — Port B I/O / ICSP data 3 |
| Pin produk 39 | RB1/PGEC3 — Port B I/O / ICSP clock 3 |
| Pin produk 40 | RB2/PGED2 — Port B I/O / ICSP data 2 |
| Pin produk 41 | RB3/PGEC2 — Port B I/O / ICSP clock 2 |
| Pin produk 42 | RB4 — Port B I/O |
| Pin produk 43 | RB5 — Port B I/O |
| Pin produk 44 | RB6 — Port B I/O |
| Pin produk 45 | RB7 — Port B I/O |
| Pin produk 46 | RB8 — Port B I/O |
| Pin produk 47 | VDD — Power supply 3.0-3.6 V |
| Pin produk 48 | VSS — Ground reference |
| Pin produk 49 | OSCI — Primary crystal oscillator input |
| Pin produk 50 | OSCO — Primary crystal oscillator output |
| Pin produk 51 | SOSCI — Secondary low-power oscillator input |
| Pin produk 52 | SOSCO — Secondary low-power oscillator output |
| Pin produk 53 | MCLR — Master Clear (reset), active low |
| Pin produk 54 | RE0 — Port E I/O |
| Pin produk 55 | RE1 — Port E I/O |
| Pin produk 56 | RE2 — Port E I/O |
| Pin produk 57 | RE3 — Port E I/O |
| Pin produk 58 | RE4 — Port E I/O |
| Pin produk 59 | RE5 — Port E I/O |
| Pin produk 60 | RE6 — Port E I/O |
| Pin produk 61 | RE7 — Port E I/O |
| Pin produk 62 | VDD — Power supply 3.0-3.6 V |
| Pin produk 63 | VSS — Ground reference |
| Pin produk 64 | RF0 — Port F I/O |
| Pin produk 65 | RF1 — Port F I/O |
| Pin produk 66 | RF2 — Port F I/O |
| Pin produk 67 | RF3 — Port F I/O |
| Pin produk 68 | RF4 — Port F I/O |
| Pin produk 69 | RF5 — Port F I/O |
| Pin produk 70 | RF6 — Port F I/O |
| Pin produk 71 | RF7 — Port F I/O |
| Pin produk 72 | RG0 — Port G I/O |
| Pin produk 73 | VSS — Ground reference |
| Pin produk 74 | VDD — Power supply 3.0-3.6 V |
| Pin produk 75 | RG1 — Port G I/O |
| Pin produk 76 | RG2 — Port G I/O |
| Pin produk 77 | RG3 — Port G I/O |
| Pin produk 78 | RG6 — Port G I/O |
| Pin produk 79 | RG7 — Port G I/O |
| Pin produk 80 | RG8 — Port G I/O |
| Pin produk 81 | RG9 — Port G I/O |
| Pin produk 82 | C1RX/C1IN-/RC0 — CAN1 RX / analog comparator / Port C |
| Pin produk 83 | C1TX/RC1 — CAN1 TX / Port C |
| Pin produk 84 | C2RX/C2IN-/RC2 — CAN2 RX / analog comparator / Port C |
| Pin produk 85 | C2TX/RC3 — CAN2 TX / Port C |
| Pin produk 86 | RC4 — Port C I/O |
| Pin produk 87 | RC5 — Port C I/O |
| Pin produk 88 | RC6 — Port C I/O |
| Pin produk 89 | RC7 — Port C I/O |
| Pin produk 90 | RC8 — Port C I/O |
| Pin produk 91 | RC9 — Port C I/O |
| Pin produk 92 | PWM1H/RD6 — PWM High output 1 / Port D |
| Pin produk 93 | PWM1L/RD7 — PWM Low output 1 / Port D |
| Pin produk 94 | PWM2H/RD8 — PWM High output 2 / Port D |
| Pin produk 95 | PWM2L/RD9 — PWM Low output 2 / Port D |
| Pin produk 96 | PWM3H/RD10 — PWM High output 3 / Port D |
| Pin produk 97 | PWM3L/RD11 — PWM Low output 3 / Port D |
| Pin produk 98 | RP16/RB16 — Remappable I/O (PPS), Port B |
| Pin produk 99 | VDD — Power supply 3.0-3.6 V |
| Pin produk 100 | VSS — Ground reference |
Aplikasi Umum
PIC24EP512GU810-E/PT cocok untuk 6 aplikasis: Industrial Motor Control, Automotive Body & Chassis ECU, USB-CDC/HID Peripheral Device, Industrial CAN-to-USB Gateway, Medical Patient Monitoring Equipment, Graphical HMI Touch Panel.
Industrial Motor Control
The PIC24EP512GU810-E/PT is well-suited to industrial motor control because it combines a 60 MIPS core with DSP extensions, nine 16-bit + eight 32-bit timers, high-resolution PWM, and a 12-bit ADC sampling at 1.1 Msps - enough to read three-phase currents every 50 us while sustaining field-oriented control. Its 512 KB Flash holds FOC state machines plus CANopen/J1939 stacks, and 52 KB RAM supports the USB-CDC diagnostic channel for field tuning. Compared with an MCU + external driver-FPGA scheme, this part replaces 2-3 chips with one AEC-Q100-qualified device, simplifying thermal and EMI design in servo drives and small-format industrial inverters.
Direkomendasikan
Automotive Body & Chassis ECU
The PIC24EP512GU810-E/PT fits automotive body controllers thanks to its AEC-Q100 qualification, dual ECAN 2.0B modules, and 83 digital I/O for driving lamps, switches, and actuators. The 512 KB Flash supports dual-image bootloaders and security firmware for OEM-level updates over CAN, while 52 KB RAM hosts the CAN stack plus diagnostics (UDS/KWP2000) simultaneously. Compared with discrete MCU + external CAN bridge designs, the integrated dual CAN and USB channel enable a single-chip gateway between CAN bus, USB diagnostic port, and LIN sub-nodes, reducing board area and BOM cost in BCM and chassis modules.
Direkomendasikan
USB-CDC/HID Peripheral Device
The PIC24EP512GU810-E/PT is ideal for USB peripherals because it integrates USB 2.0 Full-Speed with internal transceiver, 48 MHz clock multiplier, and pull-up control, eliminating external PHY chips. The 60 MIPS core sustains USB-HID game controller polling at 1 kHz while servicing the host's feature reports, and the 512 KB Flash holds the full HID descriptor table plus vendor commands. Compared with a basic MCU needing an external FTDI or TUSB chip, this part integrates USB, 83 GPIO, and CAN into one package, saving BOM cost and footprint in barcode scanners, test instruments, and human-interface peripherals.
Direkomendasikan
Industrial CAN-to-USB Gateway
The PIC24EP512GU810-E/PT functions as a dual-CAN to USB bridge because it exposes two independent ECAN modules alongside the USB 2.0 Full-Speed device, with the 60 MIPS core handling arbitration, buffering, and protocol translation in real time. The 52 KB RAM stores incoming CAN frames before the USB host drains them, and 512 KB Flash allows gateway configuration, CANopen, and SAE J1939 stack coexistence. Compared with separate MCU + CAN controller IC designs, this part consolidates three functions into one chip, shrinking the gateway footprint in factory-floor and automotive test interfaces.
Direkomendasikan
Medical Patient Monitoring Equipment
The PIC24EP512GU810-E/PT suits patient monitors because its 12-bit 1.1 Msps ADC digitizes multiple biosignals (ECG, SpO2, respiration) simultaneously while the 60 MIPS core runs DSP filter algorithms (FIR, FFT, peak detection) in real time. USB 2.0 transmits continuous waveforms to a host PC, and 83 GPIO drive LCD segments, keypads, and alarm circuits. Compared with discrete DSP + MCU architectures, this part delivers DSP-grade signal processing plus USB connectivity in a single AEC-Q100-qualified device, reducing component count and BOM in IEC 60601-compliant patient monitors.
Direkomendasikan
Graphical HMI Touch Panel
The PIC24EP512GU810-E/PT drives HMI panels because it offers 83 GPIO for parallel 16-bit TFT data plus control signals, a 60 MIPS core to refresh QVGA displays at 60 Hz, and USB/CAN for backhaul to higher-level controllers. The 512 KB Flash stores UI assets (fonts, icons) compressed, and 52 KB RAM holds double-buffered framebuffer regions. Compared with basic MCUs needing external display controllers, this part's combination of large Flash, high GPIO count, and integrated peripherals simplifies the BOM in industrial touch panels, elevator controllers, and home-automation hubs.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC24EP512GU810-E/PT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC24EP512GU810-I/PT | PIC24EP512GU810-E/PF | PIC24EP256GU810-I/PT | dsPIC33EP512MU810-I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-TQFP (12x12 mm) | 100-TQFP (12x12 mm) | 100-TQFP (14x14 mm) | 100-TQFP (12x12 mm) | 100-TQFP (12x12 mm) |
| CPU Speed | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz | 60 MIPS / 70 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 512 KB |
| RAM | 52 KB | 52 KB | 52 KB | 52 KB | 52 KB |
| I/O Pins | 83 | 83 | 83 | 83 | 83 |
| Operating Temperature | -40C to +125C (AEC-Q100) | -40C to +85C (industrial) | -40C to +125C (AEC-Q100) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| USB / CAN | USB 2.0 FS + 2x CAN 2.0B | USB 2.0 FS + 2x CAN 2.0B | USB 2.0 FS + 2x CAN 2.0B | USB 2.0 FS + 2x CAN 2.0B | USB 2.0 FS + 2x CAN 2.0B |
Diferensiator Kunci
- AEC-Q100 automotive qualification with extended -40C to +125C temperature range (vsPIC24EP512GU810-I/PT)
- Same 100-TQFP footprint as lower-Flash sibling (vsPIC24EP256GU810-I/PT)
- Dual ECAN 2.0B controllers instead of single CAN (vsPIC24EP512GP806-I/PT)
Catatan Desain
The PIC24EP512GU810-E/PT uses an on-chip 1.2 V LDO regulator that requires the ENVREG pin tied to VDD and a 1 uF + 10 uF ceramic decoupling network on the VDDCORE pin (pin 19). Without proper decoupling the core voltage can sag during peak computational loads (e.g. motor control), triggering brown-out resets. Place both caps within 3 mm of the pin with a wide ground via to the underlying ground plane.
Route the USB D+/D- lines (pins 7 and 8) as a 90-ohm differential pair with length matching within 150 mil; place the 48 MHz crystal (pins 49/50) within 5 mm of OSCI/OSCO with a guard ring tied to analog ground. CAN bus lines (C1TX/C1RX, C2TX/C2RX) need a 120-ohm termination resistor at each end of the bus; the CAN transceiver (e.g. MCP2562FD) should be placed within 25 mm of the MCU CAN pins to keep stubs short.
Do not leave the MCLR pin (pin 53) floating - it requires a 10 kohm pull-up to VDD for normal operation. The VREF+/VREF- pins (34/35) must be decoupled with 1 uF + 0.1 uF when using the internal ADC reference; otherwise ADC readings will exhibit 5-10 LSB noise. PPS (Peripheral Pin Select) functions must be unlocked via OSCCON.IOLOCK before programming peripheral mappings - many first-time prototypes fail at startup because developers forget this write sequence.
Informasi Konformitas
AEC-Q100 qualified per Microchip product page; E suffix denotes extended temperature range (-40C to +125C) and automotive qualification. RoHS/REACH compliance confirmed by Microchip product page.
