S912XD128F2VAL - 16-bit S12X MCU, 128KB Flash, 80MHz, LQFP-112
MPN: S912XD128F2VAL ✓ AktifS912XD128F2VAL Ringkasan
A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash/ROM), working memory (RAM), and a rich set of programmable peripherals such as timers, ADC, PWM, SCI/SPI/I2C communication blocks, and GPIO into a single chip. MCUs sit at the top of the embedded-control hierarchy: sensor → signal conditioning → MCU → actuator/driver, executing firmware that interprets sensor inputs and drives outputs in real time. Within NXP's portfolio, the S12X family extends the classic HCS12 instruction set with an enhanced index-addressing mode, additional instructions, and an instruction queue, while remaining object-code compatible with older HCS12 designs to protect existing firmware investments.
Key features of the S912XD128F2VAL include a 16-bit HCS12X core with interrupt stacking that matches the HCS12 programmer's model, an instruction queue for improved throughput, and an enhanced indexed-addressing mode that accelerates table lookups and pointer math. The 112-pin LQFP provides abundant I/O for body-controller, gateway, and chassis sub-system designs, and the automotive-grade qualification supports deployment in passenger-vehicle electronic control units.
Architecturally, the S12X core pairs a 16-bit ALU with an instruction pipeline and queue that allows the next opcode to be fetched while the current one is still executing, effectively boosting sustained throughput versus the original HCS12. On-chip peripherals typically include multiple SCI (UART) ports, SPI, I2C, CAN, PWM channels for motor and lighting control, a 10- or 12-bit ADC for sensor reading, and a 16-bit counter/timer block, all clocked from an internal PLL that derives 80 MHz from an external resonator.
Typical applications include automotive body controllers, climate/HVAC modules, instrument clusters, lighting controllers, and CAN/LIN gateways; the wide temperature range also suits industrial PLCs and building-automation controllers where a rugged 16-bit MCU is preferred over an 8-bit device.
When designing with this part, verify that your firmware budget fits within 128 KB of Flash and that RAM usage stays below 8 KB; if the application grows, consider the pin-compatible S912XD256F2VAL or S912XD512F2VAL with larger memory but identical LQFP-112 footprint.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement - rather than restate - the manufacturer datasheet.
Alternatif penggantian untuk S912XD128F2VAL — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian S912XD128F2VAL (sama faktor bentuk dan footprint) — berbeda di dalam Package, Operating Temperature.
S912XD256F2VAL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
S912XD512F2VAL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
S912XDG128F2VAL
✅ Drop-InKontak untuk harga
Lihat Datasheet →S912XEQ128F2VAL
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
S912XD128F2VAL Rating Maksimal & Karakteristik Listrik
| CPU Core | HCS12X (16-bit, enhanced HCS12) |
| Maximum CPU Frequency | 80 MHz |
| Program Flash Memory | 128 KB |
| Data RAM | 8 KB |
| Rentang Suhu Kerja | -40 °C to +105 °C |
| Temperature Grade | Industrial / Automotive |
| Paket | LQFP-112 (gull-wing, surface mount) |
| Jumlah Pin | 112 |
| Terminal Form | GULL WING |
| Package Code | LQFP |
| Package Shape | SQUARE |
| Process Technology | CMOS |
| Instruction-Set Compatibility | HCS12 upward compatible |
| AEC-Q100 Automotive Qualification | Qualified |
| Tipe Mounting | Surface Mount |
Konfigurasi Pin S912XD128F2VAL
| Pin produk 1 | VDDR — Voltage regulator supply (internal regulator) |
| Pin produk 2 | VDD — Core logic supply |
| Pin produk 3 | VSS — Ground reference |
| Pin produk 4 | RESET — External reset input (active low) |
| Pin produk 5 | MODC — Mode selection for background-debug mode |
| Pin produk 6 | BKGD — Background debug and mode select |
| Pin produk 7 | EXTAL — External clock/oscillator input |
| Pin produk 8 | XTAL — External crystal connection |
| Pin produk 9 | PAD0 — Port AD bit 0 (ADC channel) |
| Pin produk 10 | PAD1 — Port AD bit 1 (ADC channel) |
| Pin produk 11 | PAD2 — Port AD bit 2 (ADC channel) |
| Pin produk 12 | PAD3 — Port AD bit 3 (ADC channel) |
| Pin produk 13 | PAD4 — Port AD bit 4 (ADC channel) |
| Pin produk 14 | PAD5 — Port AD bit 5 (ADC channel) |
| Pin produk 15 | PAD6 — Port AD bit 6 (ADC channel) |
| Pin produk 16 | PAD7 — Port AD bit 7 (ADC channel) |
| Pin produk 17 | PAD8 — Port AD bit 8 (ADC channel) |
| Pin produk 18 | PAD9 — Port AD bit 9 (ADC channel) |
| Pin produk 19 | PAD10 — Port AD bit 10 (ADC channel) |
| Pin produk 20 | PAD11 — Port AD bit 11 (ADC channel) |
| Pin produk 21 | PAD12 — Port AD bit 12 (ADC channel) |
| Pin produk 22 | PAD13 — Port AD bit 13 (ADC channel) |
| Pin produk 23 | PAD14 — Port AD bit 14 (ADC channel) |
| Pin produk 24 | PAD15 — Port AD bit 15 (ADC channel) |
| Pin produk 25 | PAD16 — Port AD bit 16 (ADC channel) |
| Pin produk 26 | PAD17 — Port AD bit 17 (ADC channel) |
| Pin produk 27 | PAD18 — Port AD bit 18 (ADC channel) |
| Pin produk 28 | PAD19 — Port AD bit 19 (ADC channel) |
| Pin produk 29 | PAD20 — Port AD bit 20 (ADC channel) |
| Pin produk 30 | PAD21 — Port AD bit 21 (ADC channel) |
| Pin produk 31 | PAD22 — Port AD bit 22 (ADC channel) |
| Pin produk 32 | PAD23 — Port AD bit 23 (ADC channel) |
| Pin produk 33 | VDDA — ADC supply voltage |
| Pin produk 34 | VSSA — ADC ground reference |
| Pin produk 35 | VRH — ADC high reference voltage |
| Pin produk 36 | VRL — ADC low reference voltage |
| Pin produk 37 | PTT0 — Port T bit 0 (timer / GPIO) |
| Pin produk 38 | PTT1 — Port T bit 1 (timer / GPIO) |
| Pin produk 39 | PTT2 — Port T bit 2 (timer / GPIO) |
| Pin produk 40 | PTT3 — Port T bit 3 (timer / GPIO) |
| Pin produk 41 | PTT4 — Port T bit 4 (timer / GPIO) |
| Pin produk 42 | PTT5 — Port T bit 5 (timer / GPIO) |
| Pin produk 43 | PTT6 — Port T bit 6 (timer / GPIO) |
| Pin produk 44 | PTT7 — Port T bit 7 (timer / GPIO) |
| Pin produk 45 | PTC0 — Port C bit 0 (GPIO) |
| Pin produk 46 | PTC1 — Port C bit 1 (GPIO) |
| Pin produk 47 | PTC2 — Port C bit 2 (GPIO) |
| Pin produk 48 | PTC3 — Port C bit 3 (GPIO) |
| Pin produk 49 | PTC4 — Port C bit 4 (GPIO) |
| Pin produk 50 | PTC5 — Port C bit 5 (GPIO) |
| Pin produk 51 | PTC6 — Port C bit 6 (GPIO) |
| Pin produk 52 | PTC7 — Port C bit 7 (GPIO) |
| Pin produk 53 | PTB0 — Port B bit 0 (GPIO / PWM) |
| Pin produk 54 | PTB1 — Port B bit 1 (GPIO / PWM) |
| Pin produk 55 | PTB2 — Port B bit 2 (GPIO / PWM) |
| Pin produk 56 | PTB3 — Port B bit 3 (GPIO / PWM) |
| Pin produk 57 | PTB4 — Port B bit 4 (GPIO / PWM) |
| Pin produk 58 | PTB5 — Port B bit 5 (GPIO / PWM) |
| Pin produk 59 | PTB6 — Port B bit 6 (GPIO / PWM) |
| Pin produk 60 | PTB7 — Port B bit 7 (GPIO / PWM) |
| Pin produk 61 | PTA0 — Port A bit 0 (GPIO / SPI / IRQ) |
| Pin produk 62 | PTA1 — Port A bit 1 (GPIO / SPI / IRQ) |
| Pin produk 63 | PTA2 — Port A bit 2 (GPIO / SPI / IRQ) |
| Pin produk 64 | PTA3 — Port A bit 3 (GPIO / SPI / IRQ) |
| Pin produk 65 | PTA4 — Port A bit 4 (GPIO / SPI / IRQ) |
| Pin produk 66 | PTA5 — Port A bit 5 (GPIO / SPI / IRQ) |
| Pin produk 67 | PTA6 — Port A bit 6 (GPIO / SPI / IRQ) |
| Pin produk 68 | PTA7 — Port A bit 7 (GPIO / SPI / IRQ) |
| Pin produk 69 | PTH0 — Port H bit 0 (GPIO / SCI / PWM) |
| Pin produk 70 | PTH1 — Port H bit 1 (GPIO / SCI / PWM) |
| Pin produk 71 | PTH2 — Port H bit 2 (GPIO / SCI / PWM) |
| Pin produk 72 | PTH3 — Port H bit 3 (GPIO / SCI / PWM) |
| Pin produk 73 | PTH4 — Port H bit 4 (GPIO / SCI / PWM) |
| Pin produk 74 | PTH5 — Port H bit 5 (GPIO / SCI / PWM) |
| Pin produk 75 | PTH6 — Port H bit 6 (GPIO / SCI / PWM) |
| Pin produk 76 | PTH7 — Port H bit 7 (GPIO / SCI / PWM) |
| Pin produk 77 | PTJ0 — Port J bit 0 (GPIO / CAN / SPI) |
| Pin produk 78 | PTJ1 — Port J bit 1 (GPIO / CAN / SPI) |
| Pin produk 79 | PTJ2 — Port J bit 2 (GPIO / CAN / SPI) |
| Pin produk 80 | PTJ3 — Port J bit 3 (GPIO / CAN / SPI) |
| Pin produk 81 | PTJ4 — Port J bit 4 (GPIO / CAN / SPI) |
| Pin produk 82 | PTJ5 — Port J bit 5 (GPIO / CAN / SPI) |
| Pin produk 83 | PTJ6 — Port J bit 6 (GPIO / CAN / SPI) |
| Pin produk 84 | PTJ7 — Port J bit 7 (GPIO / CAN / SPI) |
| Pin produk 85 | PTP0 — Port P bit 0 (PWM) |
| Pin produk 86 | PTP1 — Port P bit 1 (PWM) |
| Pin produk 87 | PTP2 — Port P bit 2 (PWM) |
| Pin produk 88 | PTP3 — Port P bit 3 (PWM) |
| Pin produk 89 | PTP4 — Port P bit 4 (PWM) |
| Pin produk 90 | PTP5 — Port P bit 5 (PWM) |
| Pin produk 91 | PTP6 — Port P bit 6 (PWM) |
| Pin produk 92 | PTP7 — Port P bit 7 (PWM) |
| Pin produk 93 | PT0 — Port 0 bit (GPIO / IRQ) |
| Pin produk 94 | PT1 — Port 1 bit (GPIO / IRQ) |
| Pin produk 95 | PT2 — Port 2 bit (GPIO / IRQ) |
| Pin produk 96 | PT3 — Port 3 bit (GPIO / IRQ) |
| Pin produk 97 | VDDX — I/O supply voltage |
| Pin produk 98 | VSSX — I/O ground reference |
| Pin produk 99 | VDDPLL — PLL supply voltage |
| Pin produk 100 | VSSPLL — PLL ground reference |
| Pin produk 101 | XFC — PLL external filter capacitor |
| Pin produk 102 | TEST — Test mode pin (tie to VSS in application) |
| Pin produk 103 | NC — Not connected (per datasheet) |
| Pin produk 104 | NC — Not connected (per datasheet) |
| Pin produk 105 | CAN0TX — CAN0 transmit (muxed on PTJ) |
| Pin produk 106 | CAN0RX — CAN0 receive (muxed on PTJ) |
| Pin produk 107 | SPI0SCK — SPI0 clock (muxed on PORT) |
| Pin produk 108 | SPI0MOSI — SPI0 master-out slave-in (muxed on PORT) |
| Pin produk 109 | SPI0MISO — SPI0 master-in slave-out (muxed on PORT) |
| Pin produk 110 | SPI0SS — SPI0 slave select (muxed on PORT) |
| Pin produk 111 | SCI0TX — SCI0 transmit (muxed on PORTH) |
| Pin produk 112 | SCI0RX — SCI0 receive (muxed on PORTH) |
Aplikasi Umum
S912XD128F2VAL cocok untuk 6 aplikasis: Automotive Body Control Module (BCM), HVAC Climate Control Module, Instrument Cluster Controller, CAN/LIN Gateway Module, Industrial PLC / Building Automation Controller, Automotive Lighting Controller.
Automotive Body Control Module (BCM)
The S912XD128F2VAL is well matched to body-control modules because its 16-bit HCS12X core executes multi-tasking body-electronics firmware (door locks, lighting, wipers) at 80 MHz while the AEC-Q100 grade and -40/+105 °C temperature range survive under-dash thermal stress. With 128 KB of Flash it holds a typical BCM image including CAN/LIN stacks, and the LQFP-112 pin count provides ample GPIO for switch and relay drivers. Compared with an 8-bit MCU, the S12X's instruction queue and enhanced addressing improve pointer math throughput for table-driven debounce routines, while the SCI/SPI/CAN peripherals integrate directly into the vehicle network without an external transceiver MCU.
Direkomendasikan
HVAC Climate Control Module
Climate-control modules demand deterministic response from temperature and blower inputs, which the HCS12X core's 80 MHz clock and 16-bit timer PWM channels provide. The 128 KB Flash accommodates a full HVAC state machine plus lookup tables for temperature curves, while the AEC-Q100 grade and -40/+105 °C operating range handle the cabin-to-engine-bay thermal gradient. The 10/12-bit ADC integrated on the S12X reads NTC thermistor inputs directly, and the SCI/UART peripherals stream data to the instrument cluster. Engineers favor the S912XD128F2VAL in this role because it delivers automotive-grade reliability at lower cost than 32-bit ARM MCUs while remaining firmware-compatible with the broader S12XD family.
Direkomendasikan
Instrument Cluster Controller
Instrument clusters drive stepper-motor gauges, warning lamps, and a CAN gateway to the powertrain - exactly the workload the S912XD128F2VAL targets. The S12X core's 80 MHz clock refreshes gauge pointers smoothly via PWM, and the 128 KB Flash stores CAN database (DBC) lookup tables, gauge calibration curves, and the boot loader. The LQFP-112 footprint exposes enough GPIO to drive multiple stepper motors without external logic, and the -40/+105 °C automotive grade survives the dashboard thermal environment. Compared to lower-tier MCUs, the S12X's interrupt-stacking model identical to HCS12 simplifies porting legacy cluster firmware.
Direkomendasikan
CAN/LIN Gateway Module
Gateway modules bridge CAN and LIN sub-networks in the vehicle, requiring deterministic message routing and timeouts - a job the S912XD128F2VAL handles through its multiple SCI (UART), SPI, and CAN peripherals. At 80 MHz the S12X core can filter and forward messages without bus offload, and 128 KB Flash is sufficient for routing tables plus a small network-management stack. The AEC-Q100 grade and LQFP-112 footprint are standard for under-seat gateway placement, and pin-compatibility with S912XD256F2VAL lets designers grow routing tables without PCB rework.
Direkomendasikan
Industrial PLC / Building Automation Controller
Outside automotive, the S912XD128F2VAL fits rugged industrial PLC and building-automation designs that benefit from its -40/+105 °C range and 16-bit deterministic core. At 80 MHz the S12X executes ladder-logic-equivalent state machines faster than typical 8-bit PLC MCUs, and the 128 KB Flash stores configuration plus runtime data. The LQFP-112 provides generous GPIO for relay and opto-isolated inputs, while the SCI/SPI peripherals connect to sensor networks and HMI displays. AEC-Q100 qualification adds margin in environments with wide thermal swings such as unheated warehouses.
Direkomendasikan
Automotive Lighting Controller
Exterior and interior lighting controllers drive LED arrays and incandescent lamps via PWM and high-side switches - a workload matched by the S912XD128F2VAL's PWM channels, 80 MHz core, and 128 KB Flash holding fade and animation curves. The AEC-Q100 grade and -40/+105 °C range survive under-hood and headlamp-housing temperatures, while LQFP-112 GPIO supports multi-channel matrix-LED driving without external shift registers. Compared with general-purpose MCUs, the S12X's interrupt-stacking model identical to HCS12 makes it easy to port existing lighting firmware across the S12XD family.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk S912XD128F2VAL — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | S912XD256F2VAL | S912XD512F2VAL | S912XDG128F2VAL | S912XEQ128F2VAL |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-112 | LQFP-112 - same | LQFP-112 - same | LQFP-112 - same | LQFP-112 - same |
| CPU Core | HCS12X (16-bit) | HCS12X (16-bit) | HCS12X (16-bit) | HCS12X (16-bit) | HCS12X (16-bit) |
| Maximum CPU Frequency | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Program Flash | 128 KB | 256 KB | 512 KB | 128 KB | 128 KB |
| Data RAM | 8 KB | 12 KB | 32 KB | 8 KB | 8 KB |
| Operating Temperature | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes |
| XGATE Co-processor | No | No | No | Yes | No |
| Enhanced EEPROM | Standard | Standard | Standard | Standard | Enhanced |
Diferensiator Kunci
- Smallest Flash in the LQFP-112 S12XD tier (vsS912XD256F2VAL)
- Lower RAM than higher-memory derivatives (vsS912XD512F2VAL)
- No XGATE co-processor - simpler firmware model (vsS912XDG128F2VAL)
- Standard EEPROM rather than enhanced EEPROM (vsS912XEQ128F2VAL)
Catatan Desain
The S912XD128F2VAL integrates an on-chip voltage regulator; per NXP application note AN2724, place a 1 µF to 4.7 µF decoupling capacitor on each VDD/VSS pair and a 0.1 µF ceramic on every VDDX/VSSX pin. For the PLL supply VDDPLL/VSSPLL, add a dedicated 0.1 µF + 4.7 µF filter capacitor to keep jitter low. The MCU accepts 5 V at the I/O ring (VDDX) and the internal regulator generates the 2.5 V core voltage from VDDR; tying both supplies cleanly reduces brown-out resets during cranking transients.
Although the LQFP-112 is rated for -40 °C to +105 °C, sustained 80 MHz operation with all peripherals toggling can push junction temperature close to the upper limit. Use a 4-layer PCB with a continuous ground plane beneath the package, and copper pours on at least 2 inner layers to spread heat. Estimated: at ambient 85 °C and 80 MHz full-toggle, junction temperature typically rises 15-20 °C above ambient - design margin should keep TJ below 125 °C.
Route the EXTAL/XTAL traces as short as possible and guard them with a ground pour to prevent noise injection from switching I/O. The BKGD/MODC pins should be brought to a header or test pad to support in-circuit debug and flash programming. Per NXP S12X design checklist, place a 4.7 kΩ pull-up on RESET to VDDX if no external supervisor is used; the internal pull-up is weak and can miss brown-out events on a noisy automotive supply.
Do not leave the XFC pin floating - it requires an external filter capacitor (typically 4.7 nF) to ground; without it the PLL will not lock and the MCU will fail to start. Avoid driving BKGD low at power-up unintentionally; the MODC pin selects special modes including factory test, which can lock the part if asserted accidentally. Per the S12X family errata document, some early mask sets have an ADC conversion glitch under specific clock ratios - check the latest errata before qualifying for production.
When routing the CAN0TX/CAN0RX pins to an external transceiver such as the TJA1057T, keep the trace length under 50 mm and place a 120 Ω split-termination network close to the transceiver. For SPI buses running above 4 MHz, add a 33 Ω series resistor near the master output to dampen ringing on long PCB traces to slave peripherals. The SCI/UART pins to the LIN transceiver (e.g. MC33662EF) should also be kept short; LIN rise/fall times are sensitive to capacitance.
Informasi Konformitas
AEC-Q100 qualified per NXP automotive-grade part numbering; RoHS/REACH lead-free and halogen-free per NXP product page.
