S912XD128F2VAL - 16-bit S12X MCU, 128KB Flash, 80MHz, LQFP-112
MPN: S912XD128F2VAL ✓ Hoạt độngS912XD128F2VAL Tóm tắt
A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash/ROM), working memory (RAM), and a rich set of programmable peripherals such as timers, ADC, PWM, SCI/SPI/I2C communication blocks, and GPIO into a single chip. MCUs sit at the top of the embedded-control hierarchy: sensor → signal conditioning → MCU → actuator/driver, executing firmware that interprets sensor inputs and drives outputs in real time. Within NXP's portfolio, the S12X family extends the classic HCS12 instruction set with an enhanced index-addressing mode, additional instructions, and an instruction queue, while remaining object-code compatible with older HCS12 designs to protect existing firmware investments.
Key features of the S912XD128F2VAL include a 16-bit HCS12X core with interrupt stacking that matches the HCS12 programmer's model, an instruction queue for improved throughput, and an enhanced indexed-addressing mode that accelerates table lookups and pointer math. The 112-pin LQFP provides abundant I/O for body-controller, gateway, and chassis sub-system designs, and the automotive-grade qualification supports deployment in passenger-vehicle electronic control units.
Architecturally, the S12X core pairs a 16-bit ALU with an instruction pipeline and queue that allows the next opcode to be fetched while the current one is still executing, effectively boosting sustained throughput versus the original HCS12. On-chip peripherals typically include multiple SCI (UART) ports, SPI, I2C, CAN, PWM channels for motor and lighting control, a 10- or 12-bit ADC for sensor reading, and a 16-bit counter/timer block, all clocked from an internal PLL that derives 80 MHz from an external resonator.
Typical applications include automotive body controllers, climate/HVAC modules, instrument clusters, lighting controllers, and CAN/LIN gateways; the wide temperature range also suits industrial PLCs and building-automation controllers where a rugged 16-bit MCU is preferred over an 8-bit device.
When designing with this part, verify that your firmware budget fits within 128 KB of Flash and that RAM usage stays below 8 KB; if the application grows, consider the pin-compatible S912XD256F2VAL or S912XD512F2VAL with larger memory but identical LQFP-112 footprint.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement - rather than restate - the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho S912XD128F2VAL — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với S912XD128F2VAL (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature.
S912XD256F2VAL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
S912XD512F2VAL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
S912XDG128F2VAL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S912XEQ128F2VAL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
S912XD128F2VAL Tỷ lệ tối đa & tính chất điện
| CPU Core | HCS12X (16-bit, enhanced HCS12) |
| Maximum CPU Frequency | 80 MHz |
| Program Flash Memory | 128 KB |
| Data RAM | 8 KB |
| Khoảng nhiệt độ hoạt động | -40 °C to +105 °C |
| Temperature Grade | Industrial / Automotive |
| Hộp | LQFP-112 (gull-wing, surface mount) |
| Số chân | 112 |
| Terminal Form | GULL WING |
| Package Code | LQFP |
| Package Shape | SQUARE |
| Process Technology | CMOS |
| Instruction-Set Compatibility | HCS12 upward compatible |
| AEC-Q100 Automotive Qualification | Qualified |
| Kiểu lắp đặt | Surface Mount |
Cấu hình chân S912XD128F2VAL
| Chân 1 | VDDR — Voltage regulator supply (internal regulator) |
| Chân 2 | VDD — Core logic supply |
| Chân 3 | VSS — Ground reference |
| Chân 4 | RESET — External reset input (active low) |
| Chân 5 | MODC — Mode selection for background-debug mode |
| Chân 6 | BKGD — Background debug and mode select |
| Chân 7 | EXTAL — External clock/oscillator input |
| Chân 8 | XTAL — External crystal connection |
| Chân 9 | PAD0 — Port AD bit 0 (ADC channel) |
| Chân 10 | PAD1 — Port AD bit 1 (ADC channel) |
| Chân 11 | PAD2 — Port AD bit 2 (ADC channel) |
| Chân 12 | PAD3 — Port AD bit 3 (ADC channel) |
| Chân 13 | PAD4 — Port AD bit 4 (ADC channel) |
| Chân 14 | PAD5 — Port AD bit 5 (ADC channel) |
| Chân 15 | PAD6 — Port AD bit 6 (ADC channel) |
| Chân 16 | PAD7 — Port AD bit 7 (ADC channel) |
| Chân 17 | PAD8 — Port AD bit 8 (ADC channel) |
| Chân 18 | PAD9 — Port AD bit 9 (ADC channel) |
| Chân 19 | PAD10 — Port AD bit 10 (ADC channel) |
| Chân 20 | PAD11 — Port AD bit 11 (ADC channel) |
| Chân 21 | PAD12 — Port AD bit 12 (ADC channel) |
| Chân 22 | PAD13 — Port AD bit 13 (ADC channel) |
| Chân 23 | PAD14 — Port AD bit 14 (ADC channel) |
| Chân 24 | PAD15 — Port AD bit 15 (ADC channel) |
| Chân 25 | PAD16 — Port AD bit 16 (ADC channel) |
| Chân 26 | PAD17 — Port AD bit 17 (ADC channel) |
| Chân 27 | PAD18 — Port AD bit 18 (ADC channel) |
| Chân 28 | PAD19 — Port AD bit 19 (ADC channel) |
| Chân 29 | PAD20 — Port AD bit 20 (ADC channel) |
| Chân 30 | PAD21 — Port AD bit 21 (ADC channel) |
| Chân 31 | PAD22 — Port AD bit 22 (ADC channel) |
| Chân 32 | PAD23 — Port AD bit 23 (ADC channel) |
| Chân 33 | VDDA — ADC supply voltage |
| Chân 34 | VSSA — ADC ground reference |
| Chân 35 | VRH — ADC high reference voltage |
| Chân 36 | VRL — ADC low reference voltage |
| Chân 37 | PTT0 — Port T bit 0 (timer / GPIO) |
| Chân 38 | PTT1 — Port T bit 1 (timer / GPIO) |
| Chân 39 | PTT2 — Port T bit 2 (timer / GPIO) |
| Chân 40 | PTT3 — Port T bit 3 (timer / GPIO) |
| Chân 41 | PTT4 — Port T bit 4 (timer / GPIO) |
| Chân 42 | PTT5 — Port T bit 5 (timer / GPIO) |
| Chân 43 | PTT6 — Port T bit 6 (timer / GPIO) |
| Chân 44 | PTT7 — Port T bit 7 (timer / GPIO) |
| Chân 45 | PTC0 — Port C bit 0 (GPIO) |
| Chân 46 | PTC1 — Port C bit 1 (GPIO) |
| Chân 47 | PTC2 — Port C bit 2 (GPIO) |
| Chân 48 | PTC3 — Port C bit 3 (GPIO) |
| Chân 49 | PTC4 — Port C bit 4 (GPIO) |
| Chân 50 | PTC5 — Port C bit 5 (GPIO) |
| Chân 51 | PTC6 — Port C bit 6 (GPIO) |
| Chân 52 | PTC7 — Port C bit 7 (GPIO) |
| Chân 53 | PTB0 — Port B bit 0 (GPIO / PWM) |
| Chân 54 | PTB1 — Port B bit 1 (GPIO / PWM) |
| Chân 55 | PTB2 — Port B bit 2 (GPIO / PWM) |
| Chân 56 | PTB3 — Port B bit 3 (GPIO / PWM) |
| Chân 57 | PTB4 — Port B bit 4 (GPIO / PWM) |
| Chân 58 | PTB5 — Port B bit 5 (GPIO / PWM) |
| Chân 59 | PTB6 — Port B bit 6 (GPIO / PWM) |
| Chân 60 | PTB7 — Port B bit 7 (GPIO / PWM) |
| Chân 61 | PTA0 — Port A bit 0 (GPIO / SPI / IRQ) |
| Chân 62 | PTA1 — Port A bit 1 (GPIO / SPI / IRQ) |
| Chân 63 | PTA2 — Port A bit 2 (GPIO / SPI / IRQ) |
| Chân 64 | PTA3 — Port A bit 3 (GPIO / SPI / IRQ) |
| Chân 65 | PTA4 — Port A bit 4 (GPIO / SPI / IRQ) |
| Chân 66 | PTA5 — Port A bit 5 (GPIO / SPI / IRQ) |
| Chân 67 | PTA6 — Port A bit 6 (GPIO / SPI / IRQ) |
| Chân 68 | PTA7 — Port A bit 7 (GPIO / SPI / IRQ) |
| Chân 69 | PTH0 — Port H bit 0 (GPIO / SCI / PWM) |
| Chân 70 | PTH1 — Port H bit 1 (GPIO / SCI / PWM) |
| Chân 71 | PTH2 — Port H bit 2 (GPIO / SCI / PWM) |
| Chân 72 | PTH3 — Port H bit 3 (GPIO / SCI / PWM) |
| Chân 73 | PTH4 — Port H bit 4 (GPIO / SCI / PWM) |
| Chân 74 | PTH5 — Port H bit 5 (GPIO / SCI / PWM) |
| Chân 75 | PTH6 — Port H bit 6 (GPIO / SCI / PWM) |
| Chân 76 | PTH7 — Port H bit 7 (GPIO / SCI / PWM) |
| Chân 77 | PTJ0 — Port J bit 0 (GPIO / CAN / SPI) |
| Chân 78 | PTJ1 — Port J bit 1 (GPIO / CAN / SPI) |
| Chân 79 | PTJ2 — Port J bit 2 (GPIO / CAN / SPI) |
| Chân 80 | PTJ3 — Port J bit 3 (GPIO / CAN / SPI) |
| Chân 81 | PTJ4 — Port J bit 4 (GPIO / CAN / SPI) |
| Chân 82 | PTJ5 — Port J bit 5 (GPIO / CAN / SPI) |
| Chân 83 | PTJ6 — Port J bit 6 (GPIO / CAN / SPI) |
| Chân 84 | PTJ7 — Port J bit 7 (GPIO / CAN / SPI) |
| Chân 85 | PTP0 — Port P bit 0 (PWM) |
| Chân 86 | PTP1 — Port P bit 1 (PWM) |
| Chân 87 | PTP2 — Port P bit 2 (PWM) |
| Chân 88 | PTP3 — Port P bit 3 (PWM) |
| Chân 89 | PTP4 — Port P bit 4 (PWM) |
| Chân 90 | PTP5 — Port P bit 5 (PWM) |
| Chân 91 | PTP6 — Port P bit 6 (PWM) |
| Chân 92 | PTP7 — Port P bit 7 (PWM) |
| Chân 93 | PT0 — Port 0 bit (GPIO / IRQ) |
| Chân 94 | PT1 — Port 1 bit (GPIO / IRQ) |
| Chân 95 | PT2 — Port 2 bit (GPIO / IRQ) |
| Chân 96 | PT3 — Port 3 bit (GPIO / IRQ) |
| Chân 97 | VDDX — I/O supply voltage |
| Chân 98 | VSSX — I/O ground reference |
| Chân 99 | VDDPLL — PLL supply voltage |
| Chân 100 | VSSPLL — PLL ground reference |
| Chân 101 | XFC — PLL external filter capacitor |
| Chân 102 | TEST — Test mode pin (tie to VSS in application) |
| Chân 103 | NC — Not connected (per datasheet) |
| Chân 104 | NC — Not connected (per datasheet) |
| Chân 105 | CAN0TX — CAN0 transmit (muxed on PTJ) |
| Chân 106 | CAN0RX — CAN0 receive (muxed on PTJ) |
| Chân 107 | SPI0SCK — SPI0 clock (muxed on PORT) |
| Chân 108 | SPI0MOSI — SPI0 master-out slave-in (muxed on PORT) |
| Chân 109 | SPI0MISO — SPI0 master-in slave-out (muxed on PORT) |
| Chân 110 | SPI0SS — SPI0 slave select (muxed on PORT) |
| Chân 111 | SCI0TX — SCI0 transmit (muxed on PORTH) |
| Chân 112 | SCI0RX — SCI0 receive (muxed on PORTH) |
Ứng dụng tiêu biểu
S912XD128F2VAL phù hợp cho 6 Áp dụngs: Automotive Body Control Module (BCM), HVAC Climate Control Module, Instrument Cluster Controller, CAN/LIN Gateway Module, Industrial PLC / Building Automation Controller, Automotive Lighting Controller.
Automotive Body Control Module (BCM)
The S912XD128F2VAL is well matched to body-control modules because its 16-bit HCS12X core executes multi-tasking body-electronics firmware (door locks, lighting, wipers) at 80 MHz while the AEC-Q100 grade and -40/+105 °C temperature range survive under-dash thermal stress. With 128 KB of Flash it holds a typical BCM image including CAN/LIN stacks, and the LQFP-112 pin count provides ample GPIO for switch and relay drivers. Compared with an 8-bit MCU, the S12X's instruction queue and enhanced addressing improve pointer math throughput for table-driven debounce routines, while the SCI/SPI/CAN peripherals integrate directly into the vehicle network without an external transceiver MCU.
Được đề xuất
HVAC Climate Control Module
Climate-control modules demand deterministic response from temperature and blower inputs, which the HCS12X core's 80 MHz clock and 16-bit timer PWM channels provide. The 128 KB Flash accommodates a full HVAC state machine plus lookup tables for temperature curves, while the AEC-Q100 grade and -40/+105 °C operating range handle the cabin-to-engine-bay thermal gradient. The 10/12-bit ADC integrated on the S12X reads NTC thermistor inputs directly, and the SCI/UART peripherals stream data to the instrument cluster. Engineers favor the S912XD128F2VAL in this role because it delivers automotive-grade reliability at lower cost than 32-bit ARM MCUs while remaining firmware-compatible with the broader S12XD family.
Được đề xuất
Instrument Cluster Controller
Instrument clusters drive stepper-motor gauges, warning lamps, and a CAN gateway to the powertrain - exactly the workload the S912XD128F2VAL targets. The S12X core's 80 MHz clock refreshes gauge pointers smoothly via PWM, and the 128 KB Flash stores CAN database (DBC) lookup tables, gauge calibration curves, and the boot loader. The LQFP-112 footprint exposes enough GPIO to drive multiple stepper motors without external logic, and the -40/+105 °C automotive grade survives the dashboard thermal environment. Compared to lower-tier MCUs, the S12X's interrupt-stacking model identical to HCS12 simplifies porting legacy cluster firmware.
Được đề xuất
CAN/LIN Gateway Module
Gateway modules bridge CAN and LIN sub-networks in the vehicle, requiring deterministic message routing and timeouts - a job the S912XD128F2VAL handles through its multiple SCI (UART), SPI, and CAN peripherals. At 80 MHz the S12X core can filter and forward messages without bus offload, and 128 KB Flash is sufficient for routing tables plus a small network-management stack. The AEC-Q100 grade and LQFP-112 footprint are standard for under-seat gateway placement, and pin-compatibility with S912XD256F2VAL lets designers grow routing tables without PCB rework.
Được đề xuất
Industrial PLC / Building Automation Controller
Outside automotive, the S912XD128F2VAL fits rugged industrial PLC and building-automation designs that benefit from its -40/+105 °C range and 16-bit deterministic core. At 80 MHz the S12X executes ladder-logic-equivalent state machines faster than typical 8-bit PLC MCUs, and the 128 KB Flash stores configuration plus runtime data. The LQFP-112 provides generous GPIO for relay and opto-isolated inputs, while the SCI/SPI peripherals connect to sensor networks and HMI displays. AEC-Q100 qualification adds margin in environments with wide thermal swings such as unheated warehouses.
Được đề xuất
Automotive Lighting Controller
Exterior and interior lighting controllers drive LED arrays and incandescent lamps via PWM and high-side switches - a workload matched by the S912XD128F2VAL's PWM channels, 80 MHz core, and 128 KB Flash holding fade and animation curves. The AEC-Q100 grade and -40/+105 °C range survive under-hood and headlamp-housing temperatures, while LQFP-112 GPIO supports multi-channel matrix-LED driving without external shift registers. Compared with general-purpose MCUs, the S12X's interrupt-stacking model identical to HCS12 makes it easy to port existing lighting firmware across the S12XD family.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho S912XD128F2VAL — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | S912XD256F2VAL | S912XD512F2VAL | S912XDG128F2VAL | S912XEQ128F2VAL |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-112 | LQFP-112 - same | LQFP-112 - same | LQFP-112 - same | LQFP-112 - same |
| CPU Core | HCS12X (16-bit) | HCS12X (16-bit) | HCS12X (16-bit) | HCS12X (16-bit) | HCS12X (16-bit) |
| Maximum CPU Frequency | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Program Flash | 128 KB | 256 KB | 512 KB | 128 KB | 128 KB |
| Data RAM | 8 KB | 12 KB | 32 KB | 8 KB | 8 KB |
| Operating Temperature | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes |
| XGATE Co-processor | No | No | No | Yes | No |
| Enhanced EEPROM | Standard | Standard | Standard | Standard | Enhanced |
Bảo phân biệt quan trọng
- Smallest Flash in the LQFP-112 S12XD tier (vsS912XD256F2VAL)
- Lower RAM than higher-memory derivatives (vsS912XD512F2VAL)
- No XGATE co-processor - simpler firmware model (vsS912XDG128F2VAL)
- Standard EEPROM rather than enhanced EEPROM (vsS912XEQ128F2VAL)
Ghi chú thiết kế
The S912XD128F2VAL integrates an on-chip voltage regulator; per NXP application note AN2724, place a 1 µF to 4.7 µF decoupling capacitor on each VDD/VSS pair and a 0.1 µF ceramic on every VDDX/VSSX pin. For the PLL supply VDDPLL/VSSPLL, add a dedicated 0.1 µF + 4.7 µF filter capacitor to keep jitter low. The MCU accepts 5 V at the I/O ring (VDDX) and the internal regulator generates the 2.5 V core voltage from VDDR; tying both supplies cleanly reduces brown-out resets during cranking transients.
Although the LQFP-112 is rated for -40 °C to +105 °C, sustained 80 MHz operation with all peripherals toggling can push junction temperature close to the upper limit. Use a 4-layer PCB with a continuous ground plane beneath the package, and copper pours on at least 2 inner layers to spread heat. Estimated: at ambient 85 °C and 80 MHz full-toggle, junction temperature typically rises 15-20 °C above ambient - design margin should keep TJ below 125 °C.
Route the EXTAL/XTAL traces as short as possible and guard them with a ground pour to prevent noise injection from switching I/O. The BKGD/MODC pins should be brought to a header or test pad to support in-circuit debug and flash programming. Per NXP S12X design checklist, place a 4.7 kΩ pull-up on RESET to VDDX if no external supervisor is used; the internal pull-up is weak and can miss brown-out events on a noisy automotive supply.
Do not leave the XFC pin floating - it requires an external filter capacitor (typically 4.7 nF) to ground; without it the PLL will not lock and the MCU will fail to start. Avoid driving BKGD low at power-up unintentionally; the MODC pin selects special modes including factory test, which can lock the part if asserted accidentally. Per the S12X family errata document, some early mask sets have an ADC conversion glitch under specific clock ratios - check the latest errata before qualifying for production.
When routing the CAN0TX/CAN0RX pins to an external transceiver such as the TJA1057T, keep the trace length under 50 mm and place a 120 Ω split-termination network close to the transceiver. For SPI buses running above 4 MHz, add a 33 Ω series resistor near the master output to dampen ringing on long PCB traces to slave peripherals. The SCI/UART pins to the LIN transceiver (e.g. MC33662EF) should also be kept short; LIN rise/fall times are sensitive to capacitance.
Thông tin tuân thủ
AEC-Q100 qualified per NXP automotive-grade part numbering; RoHS/REACH lead-free and halogen-free per NXP product page.
