SN75LVDS84ADGGR - 21:3 FlatLink LVDS Transmitter 48-TSSOP | TI
MPN: SN75LVDS84ADGGR ✓ AktifSN75LVDS84ADGGR Ringkasan
A FlatLink transmitter is a parallel-to-serial LVDS serializer designed to reduce cable and connector pin count while maintaining high-speed signaling. Within the device, three 7-bit parallel-load serial-out shift registers, a 7× clock synthesizer, and four LVDS line drivers serialize and convert single-ended LVTTL data on the controller side to differential LVDS pairs on the display side, yielding very low EMI compared to wide parallel TTL buses.
Key features include 21:3 data compression, throughput up to 196 MBps, 3 data channels plus clock in LVDS, single-ended LVTTL inputs with on-chip 110-ohm termination, low EMI generation, and compatibility with paired receivers such as the SN75LVDS82 and SN65LVDS86. The 'A' revision improves ESD protection and offers the automotive-qualified SN65LVDS84AQ pin-compatible counterpart for AEC-Q100 designs.
Typical applications span LCD monitor/TV controller-to-panel interconnects, SVGA/XGA/SXGA flat-panel displays, notebook/embedded display modules, projector engines, industrial HMI panels, and digital signage controllers where low-EMI high-speed links are required. It is commonly paired with the SN75LVDS82 receiver on the TCON side.
Design considerations include providing a stable parallel clock and ensuring the receiver end meets the LVDS TIA/EIA-644 standard; 100-ohm differential termination is required at the receiver input. PCB layout must enforce 50-ohm controlled-impedance traces for each LVDS pair and length matching within the pair to preserve duty cycle.
This page combines distributor pricing, AEC-Q100 pin-compatible variants, application pairing with the SN75LVDS82 receiver, and PCB layout notes not found in the manufacturer datasheet alone.
Alternatif penggantian untuk SN75LVDS84ADGGR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian SN75LVDS84ADGGR (sama faktor bentuk dan footprint) — berbeda di dalam Data Rate, Function.
SN75LVDS84ADGG
✅ Drop-InKontak untuk harga
Lihat Datasheet →SN65LVDS84AQDGG
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN75LVDS84DGG
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN75LVDS84ADGGR Spesifikasi
| Fungsi | LVDS FlatLink 21-bit transmitter (Serializer) |
| Number of Drivers | 4 (3 data + 1 clock) |
| Laju Data | Up to 196 MBps (megabytes per second) |
| Rentang Tegangan Masukan | 3 V to 3.6 V (LVTTL single-ended) |
| LVDS Output Swing | Typical 350 mV differential |
| Number of Input Channels | 21 LVTTL data + 1 clock |
| Number of Output Channels | 3 LVDS data pairs + 1 LVDS clock pair |
| Common-Mode Range | 0 V to 2.4 V |
| Propagation Delay | Typical 2.5 ns |
| Rentang Suhu Kerja | 0 C to +70 C |
| Package Type | 48-TSSOP (DGG) |
| Tipe Mounting | Surface Mount |
| Level MSL | 2 (1 year floor life) |
| Status RoHS | Compliant |
| Lead-Free | Yes |
| Family | FlatLink |
| AEC-Q100 Qualified | No (use SN65LVDS84AQDGG for automotive) |
Konfigurasi Pin SN75LVDS84ADGGR
| Pin produk 1 | VCC — Power supply, 3.3V |
| Pin produk 2 | D0 — LVTTL data input bit 0 |
| Pin produk 3 | D1 — LVTTL data input bit 1 |
| Pin produk 4 | D2 — LVTTL data input bit 2 |
| Pin produk 5 | D3 — LVTTL data input bit 3 |
| Pin produk 6 | D4 — LVTTL data input bit 4 |
| Pin produk 7 | D5 — LVTTL data input bit 5 |
| Pin produk 8 | D6 — LVTTL data input bit 6 |
| Pin produk 9 | GND — Ground |
| Pin produk 10 | D7 — LVTTL data input bit 7 |
| Pin produk 11 | D8 — LVTTL data input bit 8 |
| Pin produk 12 | D9 — LVTTL data input bit 9 |
| Pin produk 13 | D10 — LVTTL data input bit 10 |
| Pin produk 14 | D11 — LVTTL data input bit 11 |
| Pin produk 15 | D12 — LVTTL data input bit 12 |
| Pin produk 16 | D13 — LVTTL data input bit 13 |
| Pin produk 17 | D14 — LVTTL data input bit 14 |
| Pin produk 18 | D15 — LVTTL data input bit 15 |
| Pin produk 19 | GND — Ground |
| Pin produk 20 | D16 — LVTTL data input bit 16 |
| Pin produk 21 | D17 — LVTTL data input bit 17 |
| Pin produk 22 | D18 — LVTTL data input bit 18 |
| Pin produk 23 | D19 — LVTTL data input bit 19 |
| Pin produk 24 | D20 — LVTTL data input bit 20 |
| Pin produk 25 | GND — Ground |
| Pin produk 26 | NC — Not connected |
| Pin produk 27 | CLKIN — LVTTL pixel clock input |
| Pin produk 28 | VCC — Power supply, 3.3V |
| Pin produk 29 | VCC — Power supply, 3.3V |
| Pin produk 30 | NC — Not connected |
| Pin produk 31 | Y0M — LVDS data output 0 negative |
| Pin produk 32 | Y0P — LVDS data output 0 positive |
| Pin produk 33 | Y1M — LVDS data output 1 negative |
| Pin produk 34 | Y1P — LVDS data output 1 positive |
| Pin produk 35 | GND — Ground |
| Pin produk 36 | Y2M — LVDS data output 2 negative |
| Pin produk 37 | Y2P — LVDS data output 2 positive |
| Pin produk 38 | GND — Ground |
| Pin produk 39 | CLKOUTM — LVDS clock output negative |
| Pin produk 40 | CLKOUTP — LVDS clock output positive |
| Pin produk 41 | GND — Ground |
| Pin produk 42 | NC — Not connected |
| Pin produk 43 | NC — Not connected |
| Pin produk 44 | VCC — Power supply, 3.3V |
| Pin produk 45 | NC — Not connected |
| Pin produk 46 | NC — Not connected |
| Pin produk 47 | VCC — Power supply, 3.3V |
| Pin produk 48 | VCC — Power supply, 3.3V |
Aplikasi Umum
SN75LVDS84ADGGR cocok untuk 6 aplikasis: LCD Monitor Flat-Panel Interconnect (SVGA/XGA/SXGA), Embedded Display Modules (Industrial HMI Panels), Notebook LCD Display Interconnect, Digital Signage and Large-Format Displays, Automotive Infotainment Displays (via SN65LVDS84AQ Pin-Compatible Variant), Projector Engines and Projection Displays.
LCD Monitor Flat-Panel Interconnect (SVGA/XGA/SXGA)
The SN75LVDS84ADGGR is purpose-built for the controller-to-panel link in SVGA (800x600), XGA (1024x768), and SXGA (1280x1024) flat-panel LCD monitors. With 21 LVTTL input bits plus clock, it serializes one full pixel per pixel clock into three LVDS data pairs plus one LVDS clock pair, supporting throughput up to 196 MBps per TI FlatLink documentation. The differential LVDS signaling provides low EMI and tolerates long PCB or flex-cable runs between the graphics controller and the panel TCON. Most SVGA/XGA/SXGA panels from major LCD manufacturers accept this FlatLink signaling natively, making the SN75LVDS84ADGGR the de facto serializer for these resolutions.
Direkomendasikan
Embedded Display Modules (Industrial HMI Panels)
Industrial human-machine interface (HMI) panels using XGA or SXGA LCDs benefit from the SN75LVDS84ADGGR's low-EMI differential LVDS link that rejects common-mode noise in factory environments. Per the TI FlatLink datasheet, the 21:3 compression reduces 21 single-ended TTL signals plus clock to 4 differential pairs (3 data + 1 clock), dramatically reducing cable pin count and improving EMC compliance. The 3.3V LVTTL inputs interface directly to common graphics controllers, ARM SoCs, or FPGA-based display pipelines. Industrial HMI designers value the long cable reach enabled by LVDS, simplifying chassis layout where the controller board and display are separated by an enclosure wall.
Direkomendasikan
Notebook LCD Display Interconnect
The SN75LVDS84ADGGR was originally designed for notebook LCD panels and remains in use for XGA/SXGA notebook display upgrades. Per TI FlatLink datasheet, the 48-TSSOP is footprint-compatible with the wiring harnesses used in legacy notebook designs, and the low EMI signature helps meet FCC Class B radiated emission limits. The 21 LVTTL data bits correspond to 18-bit color RGB plus HSync/VSync/EN, suitable for the 18-bit-per-pixel color depth typical of XGA notebook LCDs. The throughput of 196 MBps supports up to SXGA 60 Hz refresh at the 65 MHz pixel clock commonly used in mid-2000s notebook displays.
Direkomendasikan
Digital Signage and Large-Format Displays
Digital signage systems using large-format XGA/SXGA LCD panels use the SN75LVDS84ADGGR to drive long-distance LVDS links between the media player and the panel. According to TI FlatLink documentation, the LVDS signaling tolerates several meters of twisted-pair or controlled-impedance flex cable without signal integrity issues, supporting wall-mounted display installations. The low-EMI differential signaling allows system integrators to pass CE/FCC radiated emission tests without extensive shielding. Pairing the SN75LVDS84ADGGR with the SN75LVDS82 or SN65LVDS86AQDGG on the panel TCON completes a robust FlatLink link suitable for 24/7 commercial signage.
Direkomendasikan
Automotive Infotainment Displays (via SN65LVDS84AQ Pin-Compatible Variant)
While the SN75LVDS84ADGGR itself is commercial-grade (0 C to +70 C), the pin-compatible AEC-Q100 SN65LVDS84AQDGG variant supports the same FlatLink protocol in automotive infotainment displays, instrument clusters, and rear-seat entertainment. Per TI automotive datasheets, this variant operates from -40 C to +85 C and meets automotive EMC requirements, allowing direct PCB reuse for both commercial and automotive designs. Designers building automotive XGA/SXGA LCD clusters can swap the SN65LVDS84AQDGG onto the same 48-TSSOP footprint without software or layout changes, accelerating platform design across consumer and automotive variants.
Direkomendasikan
Projector Engines and Projection Displays
Projector engines and front-projection display systems frequently use the SN75LVDS84ADGGR to serialize LVTTL data from the video processor to the DMD/LCD imager board. Per TI FlatLink datasheet, the 196 MBps throughput supports XGA and SXGA pixel rates, while the small 48-TSSOP footprint fits inside the compact projector engine housing. Differential LVDS transmission through a flex cable isolates the noisy digital video processor from the sensitive analog imager circuits, improving display image quality by reducing noise coupling. This application is common in conference room projectors, pico-projectors, and rear-projection TVs of the mid-2000s generation.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SN75LVDS84ADGGR — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SN75LVDS84ADGG | SN65LVDS84AQDGG | SN75LVDS84DGG |
|---|---|---|---|---|
| Package | 48-TSSOP (DGG) | 48-TSSOP (DGG) - same | 48-TSSOP (DGG) - same | 48-TSSOP (DGG) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | Transmitter (Serializer) | Transmitter | Transmitter | Transmitter |
| Operating Temperature | 0 C to +70 C | 0 C to +70 C | -40 C to +85 C | 0 C to +70 C |
| AEC-Q100 Qualified | No | No | Yes | No |
| Data Throughput | Up to 196 MBps | Up to 196 MBps | Up to 196 MBps | Up to 196 MBps |
| LVTTL Data Inputs | 21 bits + clock | 21 bits + clock | 21 bits + clock | 21 bits + clock |
| Packaging Media | Tape & Reel | Tray | Tape & Reel | Tray |
| Silicon Revision | 'A' revision | 'A' revision | 'A' revision automotive | Pre-A revision |
Diferensiator Kunci
- Pin-compatible AEC-Q100 automotive variant available for drop-in platform reuse (vsSN65LVDS84AQDGG)
- Silicon 'A' revision with improved ESD protection over earlier die (vsSN75LVDS84DGG)
- Tape-and-reel packaging for high-volume SMT assembly (vsSN75LVDS84ADGG (tray variant))
Catatan Desain
Route each LVDS differential pair with 100-ohm differential impedance and keep intra-pair trace length matching within 50 mils to preserve duty cycle. Use 3.3V power and ground planes under the TSSOP-48 with bypass capacitors of 0.1 uF and 10 uF placed within 5 mm of each VCC pin. Avoid routing LVTTL data signals parallel to LVDS outputs to minimize crosstalk, per TI FlatLink application note SLDA004A.
Do not place the 100-ohm LVDS termination at the SN75LVDS84ADGGR transmitter outputs - the LVDS driver is current-steered and expects the 100-ohm load only at the receiver end. Per TIA/EIA-644, the parallel 100-ohm resistor must be at the SN75LVDS82 receiver input. Putting termination at the transmitter will double-terminate the link and load down the driver, causing signal integrity failure.
Use controlled-impedance flex or twisted-pair cable between the SN75LVDS84ADGGR transmitter and the receiver. Per TI FlatLink datasheet, LVDS links tolerate cable skew up to one bit period, but excessive skew will corrupt pixel data. For SXGA panels running 65 MHz pixel clock, target intra-pair skew below 50 ps and inter-pair skew below one UI (15 ns at 65 MHz).
The SN75LVDS84ADGGR requires a clean 3.3V supply with low ripple for stable LVDS swing. Place a ferrite bead on the VCC supply rail near the IC and keep analog/digital grounds separated if integrating with analog video circuits. Estimated: at full throughput, the LVDS drivers draw approximately 50 mA total, so a low-noise LDO feeding the transmitter VCC improves display noise performance.
Informasi Konformitas
RoHS and REACH compliant per TI product page. Not AEC-Q100 qualified - use SN65LVDS84AQDGG for automotive. Halogen-free per TI Materials Declaration. Conflict-mineral statement published by TI.
