SP3232EUCT-L - 1 Mbps Dual RS-232 Transceiver | MaxLinear
MPN: SP3232EUCT-L ✓ AktifSP3232EUCT-L Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible levels. The SP3232E family integrates two line drivers, two line receivers, and a charge-pump supply, placing it within the hierarchy of interface ICs, communications transceivers, and RS-232 interface silicon.
The SP3232EUCT-L provides two transmit channels and two receive channels, allowing one RS-232 port to handle two data directions. Its single-supply operation supports both 3.3 V and 5 V system environments. The manufacturer's charge-pump design requires only 0.1 uF capacitors in 3.3 V operation, reducing external component count while preserving full RS-232 signal levels. Its 1000 kbps capability is suitable for moderate-speed serial links, including embedded control ports and industrial peripherals.
The integrated charge pump generates the positive and negative voltages needed by RS-232 drivers from the single supply. This architecture avoids a separate bipolar power source and allows the device to operate from a 3.0 V to 5.5 V source. Because the interface performs level translation at the physical layer, the connected host or target UART still handles data framing, baud-rate agreement, parity, flow control, and protocol behavior.
Typical uses include industrial control equipment, portable data-acquisition systems, service interfaces, POS terminals, and embedded debug or configuration ports. The 16-pin SOIC package supports conventional surface-mount assembly and remains practical for boards where component height is more constrained than the size of a dual-inline package.
Confirm the exact pin assignment, charge-pump capacitor values, and decoupling requirements in the manufacturer datasheet before PCB release. Preserve short, direct paths for the charge-pump nodes and place the required capacitors close to their associated pins to reduce switching noise and unstable driver behavior.
This product page combines the SP3232EUCT-L electrical characteristics, same-package replacement options, application guidance, and design notes to help engineers evaluate the transceiver quickly and implement a reliable RS-232 interface.
Alternatif penggantian untuk SP3232EUCT-L — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian SP3232EUCT-L (sama faktor bentuk dan footprint).
SP3232ECT-L/TR
✅ Drop-InKontak untuk harga
Lihat Datasheet →SP3232EUCT-L/TR
✅ Drop-InKontak untuk harga
Lihat Datasheet →SN65C3232DW
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SP3232EUCT-L Spesifikasi
| Transceiver Configuration | 2 drivers and 2 receivers |
| Interface Standard | RS-232 |
| Maximum Data Rate | 1000 kbps |
| Single Supply Voltage Range | 3.0 V to 5.5 V |
| Charge-Pump Capacitance | 0.1 uF in 3.3 V operation |
| Driver Count | 2 channels |
| Receiver Count | 2 channels |
| Package Pin Count | 16 pins |
| Package Type | SOIC-16 |
| Tipe Mounting | Surface mount |
| Supply Type | Single supply |
| Charge-Pump Supply | On-chip |
SP3232EUCT-L soic-16 Diamant Konfigurasi Panduan
Konfigurasi pin untuk SP3232EUCT-L (soic-16 pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk SP3232EUCT-L.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
SP3232EUCT-L cocok untuk 6 aplikasis: Industrial Control Interface, Portable Data-Acquisition Unit, Point-of-Sale Terminal, Embedded Debug and Configuration Port, Networking and Communication Module, Test and Measurement Equipment.
Industrial Control Interface
The SP3232EUCT-L suits an industrial controller that exposes an RS-232 configuration or service port because it combines two transmit channels, two receive channels, and a 1000 kbps maximum data rate. Its single 3.0 V to 5.5 V supply can share a rail with 3.3 V or 5 V control logic, while the integrated charge pump eliminates a separate bipolar supply. Place the required 0.1 uF capacitors close to the charge-pump pins and use a protection strategy appropriate for an externally accessible cable.
Direkomendasikan
Portable Data-Acquisition Unit
The SP3232EUCT-L is appropriate for a compact data-acquisition unit that needs to exchange commands and records with a host over RS-232. Its 16-pin SOIC footprint limits board area, while the 3.0 V to 5.5 V operating range supports both 3.3 V and 5 V systems. The 1000 kbps rate provides ample margin for many short command sequences and sampled-data packets. Ensure the UART baud rate, cable length, connector grounding, and protection network are engineered for the installation environment.
Direkomendasikan
Point-of-Sale Terminal
The SP3232EUCT-L can provide a wired service or peripheral interface in a point-of-sale terminal where dual RS-232 channels improve board utilization. Two drivers and two receivers support simultaneous transmit and receive functions, and the integrated charge pump operates from a single 3.0 V to 5.5 V rail. The surface-mount SOIC package is convenient for automated assembly. For retail deployments, add appropriate cable-side transient protection and verify the peripheral voltage levels, handshake method, and timing against the host UART.
Direkomendasikan
Embedded Debug and Configuration Port
The SP3232EUCT-L is useful for an embedded debug, programming, or configuration connector that must add a wired RS-232 interface without requiring a bipolar supply. Its 1000 kbps capability supports common service protocols and short firmware-loading sessions, while operation from 3.3 V simplifies integration with low-power processors. Keep the serial traces short, provide clean common grounding, and verify that the connector's logic side uses compatible levels. Production designs should also consider firmware-based recovery because a physical service port may not be available on every enclosure.
Direkomendasikan
Networking and Communication Module
The SP3232EUCT-L can bridge a low-voltage embedded controller to an external RS-232 management or diagnostic interface in a communication module. Its two-driver, two-receiver arrangement provides flexibility for separate command and status channels, and the single-supply charge pump supports space-constrained designs. At 1000 kbps, the interface can carry diagnostic traffic efficiently without imposing the power and space demands of a separate line-driver assembly. Validate protocol timing and add surge protection when the cable leaves the equipment enclosure.
Direkomendasikan
Test and Measurement Equipment
The SP3232EUCT-L is suitable for the control or remote-command interface of test and measurement equipment because it combines a 1 Mbps RS-232 channel set with a compact surface-mount package. The interface can connect a legacy controller, service computer, or automation fixture while receiving responses over the integrated receiver channels. Its broad single-supply range makes it practical across 3.3 V and 5 V instrument architectures. Use shielded cabling, reliable grounding, and connector-side protection where the equipment supports long external leads or frequent reconnections.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SP3232EUCT-L — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SP3232ECT-L/TR | SP3232EUCT-L/TR | SN65C3232DW |
|---|---|---|---|---|
| Brand | MaxLinear, Inc. | MaxLinear, Inc. | MaxLinear, Inc. | Texas Instruments |
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Transceiver Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 |
| Charge-Pump Supply | Integrated | Integrated | Integrated | Dual charge-pump circuit |
Diferensiator Kunci
- Two full-duplex RS-232 channels in one package (vsMAX3221IPWR)
- Single-supply operation across 3.3 V and 5 V systems (vsSN65C3232DW)
- High-speed RS-232 operation (vsSP3232ECT-L/TR)
Catatan Desain
Place the charge-pump capacitors and supply-decoupling capacitor as close as practical to their associated SP3232EUCT-L pins. The manufacturer specifies 0.1 uF charge-pump capacitors for 3.3 V operation. Short capacitor connections reduce the loop area of the switching charge pump and help limit conducted and radiated noise. Follow the manufacturer datasheet layout for the exact capacitor connections and exposed-pin treatment.
Route RS-232 driver and receiver traces away from clocks, switching supplies, and high-slew-rate digital signals. Although the maximum device data rate is 1000 kbps, connector transitions, cable loading, reflections, and ground differences can still cause errors on longer links. Keep the interface ground return close to the signal path, use controlled-impedance routing where appropriate, and validate the completed board with the intended cable and connector.
Do not select a replacement solely because both devices use a 16-pin SOIC. Verify the pin-to-pin assignments, enable polarity, driver and receiver thresholds, charge-pump capacitor network, operating-temperature grade, and ESD rating. SP3232ECT-L/TR is documented at 0 C to 70 C, while the SN65C3232DW description includes ±15 kV ESD protection. Those differences can affect production qualification even when the package outlines match.
The integrated charge pump switches internally to generate RS-232 voltage levels. Use the capacitor values and placement shown in the manufacturer datasheet, and avoid routing the charge-pump nets beneath long sensitive analog or communication paths. If radiated emissions approach the product's regulatory limits, examine the supply network, cable common mode, connector return path, and board grounding before changing the transceiver itself.
Informasi Konformitas
AEC-Q100 qualification is not applicable to this general-purpose RS-232 interface. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current material documentation.