TCA9509RVHR - 2-Bit I2C Level Translator | Texas Instruments
MPN: TCA9509RVHR ✓ AktifTCA9509RVHR Ringkasan
An I2C level translator is an interface IC that connects logic operating at different voltage levels on the same serial bus. Its position in the hierarchy is I2C repeater, level translator, interface IC, and ultimately semiconductor. This bidirectional separation helps prevent low-voltage devices from receiving signals that exceed their input limits and helps keep high-voltage devices from exposing low-voltage nodes to excessive voltage.
The principal features are two independently level-translated bus channels, operation up to 400 kHz, an internal 1 mA current source, and support for both I2C and SMBus signaling. The small X2QFN package supports compact PCB layouts where board area is constrained. Its buffer function can also isolate capacitive loading between bus segments and improve signal integrity in multi-board or multi-device systems.
The B-side drivers use SMBus-compatible I/O levels, while the A-side uses current sensing to identify LOW states and avoid bus lock-up. The A-side includes the internal 1 mA current source for pull-up support. This arrangement accommodates smaller LOW-state voltage swings while retaining bidirectional data transfer, which is important when connecting peripherals with different supply voltages.
Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus management interfaces, compact industrial modules, embedded instrumentation, and systems that divide a long I2C bus into shorter electrically isolated segments. The device is particularly useful when cables, connectors, or PCB routing introduce capacitance between bus nodes.
When laying out the circuit, treat the A-side and B-side pull-up networks as separate domains and confirm that the external pull-up strength works with the intended bus voltage and capacitance. Avoid adding unnecessary capacitance near the small package, and verify signal rise times at the maximum intended I2C clock rate. Bus timing and voltage margins remain the responsibility of the final board design.
This page combines the manufacturer product information, ordering data, documented cross-reference details, packaging characteristics, and practical design guidance in one engineering-focused view. It also distinguishes true pin-compatible interchange from merely similar I2C switching devices, helping designers make a replacement decision without assuming that equal functionality guarantees equal footprint or pin behavior.
Alternatif penggantian untuk TCA9509RVHR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TCA9509RVHR (sama faktor bentuk dan footprint).
TCA9509MRVHR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TCA9509RVHR Spesifikasi
| Product Type | 2-bit level-translating I2C/SMBus buffer and repeater |
| Number of Bus Channels | 2 bits |
| Maximum Bus Clock Frequency | 400 kHz |
| Internal Pull-Up Current Source | 1 mA |
| Supported Interfaces | I2C and SMBus |
| Maximum Supply Voltage | 5.5 V |
| A-Side Architecture | Current-sensing LOW detection with 1 mA pull-up current source |
| B-Side Driver Levels | SMBus-compatible I/O levels |
| Package Type | X2QFN-8 (RVH) |
| Package Dimensions | 1.6 mm x 1.6 mm |
| Jumlah Pin | 8 pins |
| Tipe Mounting | Surface mount |
TCA9509RVHR 1.6 mm x 1.6 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk TCA9509RVHR (1.6 mm x 1.6 mm pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk TCA9509RVHR.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TCA9509RVHR cocok untuk 6 aplikasis: Low-Voltage Sensor Level Translation, SMBus Management Interface, Embedded Instrumentation, Multi-Board I2C Isolation, Industrial Control Module, Low-Power Sensor Node.
Low-Voltage Sensor Level Translation
The TCA9509RVHR fits between a low-voltage sensor and a controller operating at a higher logic level because its bidirectional A-side and B-side paths support two independently translated bus bits. Texas Instruments identifies the device for I2C/SMBus communication up to 400 kHz and includes an internal 1 mA current source on the A-side. This arrangement helps protect lower-voltage devices from excessive input voltage while retaining standard two-wire addressing and data transfer. External pull-ups should be sized for each supply domain and checked against the bus capacitance before operating near the 400 kHz limit.
Direkomendasikan
SMBus Management Interface
The TCA9509RVHR is appropriate for an SMBus management segment because its B-side drivers use SMBus-compatible I/O levels and its A-side detects LOW states through current sensing. The two-bit repeater can connect management devices operating at different supply voltages without changing the host's bus protocol. Texas Instruments specifies operation up to 400 kHz, which supports standard I2C/SMBus management traffic while allowing separate pull-up networks for each voltage domain. Verify the available pull-up current, rise time, and bus capacitance in the final topology.
Direkomendasikan
Embedded Instrumentation
The TCA9509RVHR can isolate a compact measurement peripheral from a controller when their digital interfaces use different logic voltages. The 8-pin 1.6 mm by 1.6 mm X2QFN package preserves PCB area in dense instrumentation, while the two translated channels support bidirectional register reads and writes. Its 400 kHz maximum bus rate is sufficient for many control and configuration registers rather than high-volume streaming. Place the repeater near the voltage-domain boundary and keep the pull-up network close to the associated bus segment to maintain predictable signal behavior.
Direkomendasikan
Multi-Board I2C Isolation
The TCA9509RVHR is useful at a boundary between circuit boards or cable-connected modules that use different logic voltages. Repetition reduces the electrical loading presented by one bus segment to another while providing bidirectional level translation for both data and clock lines. With operation up to 400 kHz and a compact 8-pin X2QFN package, it can support conventional I2C management links without substantial board area. The resulting bus must still meet rise-time and capacitance limits, particularly when long cables or multiple pull-ups increase loading.
Direkomendasikan
Industrial Control Module
The TCA9509RVHR supports industrial control modules that combine low-voltage sensors with a higher-voltage controller or communications processor. The device translates two bidirectional I2C/SMBus lines while allowing the two sides to use their respective logic thresholds. Its 1 mA internal current source supports the A-side pull-up arrangement, and the 400 kHz capability covers typical configuration and command traffic. In a compact controller board, the 1.6 mm by 1.6 mm X2QFN package reduces routing congestion, although external pull-up selection remains essential for reliable LOW and rise-time behavior.
Direkomendasikan
Low-Power Sensor Node
The TCA9509RVHR fits between a low-power sensor node and a host running at another supply voltage when the interface must retain standard I2C behavior. Its bidirectional 2-bit architecture handles both clock and data lines, while the current-sensing A-side helps detect LOW without relying only on a fixed voltage threshold. The package occupies only 1.6 mm by 1.6 mm, which is valuable in wearable or space-constrained sensor designs. Confirm static current and voltage thresholds against the sensor's power budget, and use pull-ups that preserve acceptable rise time without adding excessive continuous current.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TCA9509RVHR — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TCA9509MRVHR |
|---|---|---|
| Package | X2QFN-8 (RVH), 1.6 mm x 1.6 mm | X2QFN-8 (RVH), 1.6 mm x 1.6 mm |
| Brand | Texas Instruments | Texas Instruments |
| Product Function | 2-bit level-translating I2C/SMBus buffer and repeater | 2-bit level-translating I2C/SMBus buffer and repeater |
| Maximum Bus Frequency | 400 kHz | 400 kHz |
| Internal Current Source | 1 mA | 1 mA |
| Maximum Supply Voltage | 5.5 V | 5.5 V |
| B-Side Driver Levels | SMBus-compatible I/O levels | SMBus-compatible I/O levels |
| Manufacturing Difference | NiPdAuAg or NiPdAu manufacturing-site finish | NiPdAuAg manufacturing-site finish; carrier orientation differs |
| Functional Equivalence | Reference device | Electrically identical and produced on the same manufacturing line |
Diferensiator Kunci
- Documented electrical equivalence with an available same-package substitute (vsTCA9509MRVHR)
- Integrated bidirectional level translation (vsPCA9509GM,125)
- Compact placement for space-constrained interface routing (vsLarger-package I2C switches)
Catatan Desain
Treat the A-side and B-side as separate voltage domains when assigning pull-up resistors and bypassing components. Place each pull-up network close to the devices that share its bus domain, and place local supply decoupling near the TCA9509RVHR power pins. Keep the routing between the repeater and the two bus segments short enough to control capacitance, especially when the design approaches the 400 kHz operating limit.
Do not assume that the internal 1 mA current source eliminates the need to validate pull-up strength. The external pull-up must establish the intended voltage-domain logic levels and provide an acceptable rising edge under the actual bus capacitance. Confirm both LOW-level voltage and rise time at the longest intended cable length; otherwise communication can fail intermittently even though each individual component passes a short bench test.
Use the exact RVH land pattern and exposed-pad requirements from the manufacturer package drawing. Avoid placing test points or unrelated copper structures beneath the device unless the package drawing permits it. Preserve short return paths for both logic domains, and avoid routing the sensitive A-side and B-side nets parallel to high-current switching paths. Controlled creepage and clearance also remain important if the two domains use widely separated voltages.
Informasi Konformitas
One manufacturing-site finish is identified as NiPdAuAg, but separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not present in the cited product information.