TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP
MPN: TJA1041AT/N ✗ Akhir HidupTJA1041AT/N Ringkasan
A CAN transceiver, also called a CAN physical-layer interface, converts logic-level signals from a CAN controller into differential bus signals and converts the received bus state back into a logic signal. Within the automotive electronics hierarchy, the TJA1041AT/N belongs to the CAN interface IC class, connecting the protocol-control layer to the physical communication bus.
The principal feature of the TJA1041AT/N is its support for high-speed CAN communication up to 1 Mbit/s. Differential CAN signaling improves immunity to electromagnetic noise, while the transceiver's transmit and receive paths integrate the controller and bus into one physical-layer solution. The device is specifically intended for automotive high-speed CAN nodes, where robust differential signaling, compact packaging, and predictable interoperability are important.
The TJA1041A family uses a nominal 5 V operating environment, with the documented supply range of 4.75 V to 5.25 V. The 14-pin SO package supports surface-mount PCB assembly and provides the CANH and CANL bus connections together with controller-facing TXD, RXD, and error-status signaling. Exact pin functions, absolute maximum ratings, loop-delay limits, and output-stage characteristics should be taken from the manufacturer datasheet.
Typical deployments include automotive body and comfort modules, powertrain controllers, gateway units, cluster electronics, infotainment systems, and industrial CAN equipment that implements a compatible high-speed CAN physical layer. In these systems, the transceiver replaces discrete driver and receiver circuitry around the CAN controller while keeping the PCB layout compact.
When laying out the circuit, place the transceiver close to the bus connector and route CANH and CANL as a matched differential pair. Keep the connection from CANH and CANL through the connector as short as practical, follow the datasheet recommendations for termination, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. The NXP product page identifies TJA1041AT as end of life, so new designs should confirm the recommended successor before committing the footprint.
This page combines the manufacturer's product information, datasheet links, distributor records, lifecycle information, and packaging details with practical application guidance, comparison parameters, and board-level design notes. It is intended to accelerate component selection and design-in work while keeping the final engineering decisions anchored to the official NXP documentation.
Alternatif penggantian untuk TJA1041AT/N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
TJA1041AT/CM,118
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TJA1041AT/N,112
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TJA1041AT/N,118
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TJA1041AT/V,518
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TJA1041AT/H/V,518
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TJA1041T/C
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TJA1041AT/N Spesifikasi
| Product Type | High-speed CAN transceiver |
| Maximum CAN Data Rate | 1 Mbit/s |
| Nominal Supply Voltage | 5 V |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Bus Interface | Differential CANH and CANL |
| Controller Interface | Differential transmit and receive capability |
| Paket | 14-pin SO package |
| Package Type | SOIC-14 |
| Tipe Mounting | Surface mount |
| Jumlah Pin | 14 pins |
| Primary Application | Automotive high-speed CAN nodes |
| Transmit Output Type | Differential |
| Receive Output Type | Differential receive |
| Protocol Compatibility | Controller Area Network (CAN) |
| Status Lingkungan Hidup | End of Life |
| Manufacturer | NXP Semiconductors |
TJA1041AT/N soic-14 Diamant Konfigurasi Panduan
Konfigurasi pin untuk TJA1041AT/N (soic-14 pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk TJA1041AT/N.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TJA1041AT/N cocok untuk 6 aplikasis: Automotive Body Control Module, Powertrain CAN Gateway, Vehicle Infotainment CAN Interface, Industrial CAN Control Equipment, Diagnostic and Service Gateway, CAN-Based Sensor Network.
Automotive Body Control Module
The TJA1041AT/N fits an automotive body controller that exchanges switch, lighting, and door-state data over a high-speed CAN bus. Its 1 Mbit/s capability matches the TJA1041A family's documented automotive focus, while the 4.75 V to 5.25 V supply range supports conventional 5 V CAN nodes. Place it beside the CAN controller, connect CANH and CANL to the routed bus pair, and verify that the selected ordering code satisfies the vehicle program's qualification requirements.
Direkomendasikan
Powertrain CAN Gateway
A gateway between automotive CAN domains can use the TJA1041AT/N as the physical-layer device on a high-speed CAN segment. Its differential transmit and receive functions isolate the controller from the bus and support communication up to 1 Mbit/s. The 14-pin SOIC footprint also permits a conventional surface-mount layout with short bus routes to the connector. Confirm transceiver timing, fault handling, and the end-of-life replacement plan against the system requirements.
Direkomendasikan
Vehicle Infotainment CAN Interface
The TJA1041AT/N can provide the physical bus interface for infotainment head units, instrument clusters, or display controllers that participate in a high-speed CAN network. At up to 1 Mbit/s, the device addresses the classic CAN network used for vehicle status and control information. Its compact 14-pin SOIC package leaves board area for display and processing circuitry, while CANH and CANL should be routed as a controlled differential pair away from switching nodes.
Direkomendasikan
Industrial CAN Control Equipment
The TJA1041AT/N is also applicable to industrial equipment that uses a 5 V high-speed CAN physical layer, including sensor controllers, machine interfaces, and remote monitoring units. The documented 4.75 V to 5.25 V operating range suits regulated 5 V designs, and the 1 Mbit/s rate covers many controller-area-network applications. Designers should confirm bus topology, termination strategy, fault handling, and qualification expectations before adapting an automotive-origin transceiver to industrial service.
Direkomendasikan
Diagnostic and Service Gateway
A diagnostic gateway can use the TJA1041AT/N as the high-speed CAN physical-layer interface when forwarding requests and responses between a service tool, a vehicle network, and other embedded controllers. The differential bus interface supports communication up to 1 Mbit/s, while TXD and RXD connect directly to the CAN controller functions. Route the bus pair toward the diagnostic connector with minimal stubs, and validate the complete termination network under worst-case bus faults.
Direkomendasikan
CAN-Based Sensor Network
Distributed sensors, actuators, and acquisition nodes can use the TJA1041AT/N where a wired CAN bus is preferred for noise-tolerant, multi-node communication. The device's differential signaling and 1 Mbit/s data-rate capability suit moderate-speed control and monitoring networks. Its nominal 5 V supply range allows integration with conventional embedded controllers, but the system designer must provide correct bus termination, common-mode behavior, and grounding consistent with the manufacturer's reference layout.
Direkomendasikan
Data referensi engineering untuk TJA1041AT/N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Use the TJA1041AT/CM,118 when standby and sleep-mode options are explicitly required and the exact ordering code meets the product specification. The TJA1041AT/N,112, TJA1041AT/N,118, TJA1041AT/V,518, and TJA1041AT/H/V,518 provide same-family ordering choices that preserve the 14-pin footprint, but their suffixes must be checked for packing, delivery, environmental, and power-management distinctions. Consider the TJA1041T/C only after confirming that its low-power behavior and qualification match the target design. For every substitution, verify the pin configuration, supply range, timing limits, bus-fault behavior, and lifecycle status rather than relying on the package name alone.
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TJA1041AT/CM,118 | TJA1041AT/N,112 | TJA1041AT/N,118 | TJA1041AT/V,518 | TJA1041AT/H/V,518 | TJA1041T/C |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SOIC-14 | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver |
| Maximum Data Rate | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Bus Interface | Differential CANH/CANL | Differential CANH/CANL | Differential CANH/CANL | Differential CANH/CANL | Differential CANH/CANL | Differential CANH/CANL | Differential CANH/CANL |
| Low-Power Feature | TJA1041AT/N ordering options | Standby and sleep mode documented | Confirm exact ordering suffix | Confirm exact ordering suffix | Confirm exact ordering suffix | Confirm exact ordering suffix | TJA1041T family low-power options |
| Lifecycle Status | End of Life | Verify current NXP lifecycle status | Verify current NXP lifecycle status | Verify current NXP lifecycle status | Verify current NXP lifecycle status | Verify current NXP lifecycle status | Verify current NXP lifecycle status |
Diferensiator Kunci
- Documented low-power feature set in the ordering variant (vsTJA1041AT/CM,118)
- Direct family continuity with the same 14-pin footprint (vsTJA1041AT/N,118)
- Established automotive high-speed CAN positioning (vsTJA1041T/C)
Catatan Desain
Route CANH and CANL as a closely coupled differential pair from the transceiver to the bus connector. Avoid routing the pair over split ground planes or across high-current switching paths. Keep the bus connection short, minimize stubs, and follow the pin-configuration and application-layout guidance in the NXP datasheet. Maintain a continuous return path beneath the pair so differential currents encounter a substantially lower loop area.
Do not assume that ordering codes ending in N, CM, V, H/V, 112, or 118 are electrically identical. Confirm the exact standby, sleep, qualification, lead-free, packing, and delivery options against the NXP ordering table before substitution. A shared 14-pin footprint is necessary for PCB reuse, but low-power behavior and environmental qualification must also match the system requirements.
Provide a clean 4.75 V to 5.25 V supply to the transceiver and place its required bypass capacitors close to the supply pins with short ground returns. Avoid sharing noisy supply paths with actuators or switching regulators. Review the datasheet's supply-current and power-up specifications, then include the device's quiescent and operating current when sizing the regulator and the thermal budget of the module.
Termination placement must follow the physical CAN network topology rather than a fixed rule applied to every node. A 120-ohm termination is normally effective only at the two ends of the bus. Check the bus configuration, node count, cable length, and fault behavior during validation, and use the manufacturer's guidance when measuring recessive and dominant voltage levels.
Informasi Konformitas
The NXP product page identifies TJA1041AT as End of Life. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was present in the referenced listings, so these fields remain unknown.