TLE8458GUV33XUMA1 - LIN Transceiver with 5V Regulator | Infineon
MPN: TLE8458GUV33XUMA1 ✓ AktifTLE8458GUV33XUMA1 Ringkasan
A LIN transceiver is a physical-layer interface IC that connects a microcontroller or other host controller to a single-wire LIN network. LIN, or Local Interconnect Network, is a low-cost automotive communication bus used for distributed body, comfort, sensor, and actuator electronics. The TLE8458 family integrates the communications interface with a regulator so a compact module can obtain its local supply and communicate over the same board without a separate discrete transceiver and regulator.
The key application parameters are the integrated 5 V regulator, 10.4 kBd LIN data rate, 1/1 transceiver configuration, and 8-pin DSO-8-16 package. The package is also described in component listings as an 8-SOIC package, with a gull-wing surface-mount form factor. This combination makes the device appropriate for compact LIN nodes where board area, wiring simplicity, and local power regulation are important.
The Infineon TLE8458GUV33XUMA1 is positioned for 5 V LIN nodes in automotive electronics, vehicle body modules, seat and door controls, climate-control peripherals, sensor interfaces, and compact industrial LIN networks. The integrated regulator reduces the number of external power components and can simplify the local power architecture, while the transceiver handles the physical communication interface.
When laying out a board, keep the LIN connection and regulator return paths short, provide the required decoupling close to the device, and follow the manufacturer’s recommended external components. Verify the exact pin assignments, electrical limits, output tolerance, and thermal conditions against the Infineon TLE8458 datasheet before production release.
This page consolidates the manufacturer-family description, distributor identification, packaging details, application context, and practical engineering considerations for engineers evaluating the TLE8458GUV33XUMA1 in LIN-based electronic systems.
Alternatif penggantian untuk TLE8458GUV33XUMA1 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
TLE8458GUV33XUMA2
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLE8458GUV33XA
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
TLE8458GUV33XUMA1
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →TLE8458GUV33XUMA1 Rating Maksimal & Karakteristik Listrik
| Product Type | LIN transceiver with integrated voltage regulator |
| LIN Bus Data Rate | 10.4 kBd |
| Transceiver Configuration | 1/1 transceiver |
| Integrated Regulator Output | 5 V |
| Output Voltage Tolerance | Maximum 2 % |
| Minimum Output Voltage | 3.234 V |
| Paket | PG-DSO-8-16, 8 pins |
| Package Family | 8-SOIC / DSO-8 surface-mount package |
| Terminal Count | 8 terminals |
| Terminal Form | Gull wing |
| Tipe Mounting | Surface mount |
TLE8458GUV33XUMA1 8-soic / dso-8 surface-mount package Diamant Konfigurasi Panduan
Konfigurasi pin untuk TLE8458GUV33XUMA1 (8-soic / dso-8 surface-mount package pakai pakai). Alat kuasa ini memiliki terminal gate, drain, dan sumber. Untuk pakai pakai yang tak polar, lihat datasheet produsen untuk orientasi dan detil footprint pin 1 yang pasti. Aplikasi umum termasuk desain penolong daya, menggerakkan motor, dan mengalihkan muatan.
Tidak ada data diatribut pin yang tersedia untuk TLE8458GUV33XUMA1.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TLE8458GUV33XUMA1 cocok untuk 6 aplikasis: Automotive Door Control Module, Vehicle Seat Control Electronics, Automotive Climate-Control Peripheral, Distributed Automotive Sensor Interface, LIN-Connected Actuator Controller, Industrial LIN Sensor Network.
Automotive Door Control Module
The TLE8458GUV33XUMA1 fits compact door-control electronics that need both a LIN bus connection and a local regulated supply. Its 1/1 LIN interface operates at 10.4 kBd, matching the communication rate used by distributed vehicle body networks, while the integrated 5 V regulator provides power for the module’s local logic or sensor circuitry. Combining these functions can reduce board partitioning and wiring. The 8-pin PG-DSO-8-16 package also supports automated surface-mount assembly in space-constrained electronic control units. Use the manufacturer’s recommended LIN bus protection and bypass components around the device, and confirm the full automotive temperature and qualification requirements before production use.
Direkomendasikan
Vehicle Seat Control Electronics
Seat control modules commonly combine position sensing, motor control, and a low-speed network connection. The TLE8458GUV33XUMA1 can provide the physical LIN interface at 10.4 kBd and a 5 V local supply for associated control electronics. This integration is useful when the ECU must communicate with a central body controller over a single-wire LIN network without allocating separate board area for a discrete regulator and physical-layer transceiver. The package’s eight gull-wing terminals are practical for compact automotive PCBs, but designers should maintain the recommended trace geometry and protection components around the external LIN connection.
Direkomendasikan
Automotive Climate-Control Peripheral
A climate-control peripheral can use the TLE8458GUV33XUMA1 as its LIN node interface when it must exchange commands and sensor status with a central controller. The device’s 10.4 kBd LIN capability is appropriate for slow supervisory communication rather than high-bandwidth payloads. Its integrated 5 V regulator helps power nearby low-voltage circuitry, simplifying the power partition inside the peripheral. The design should still include adequate decoupling and a controlled return path, especially if motors, heaters, or fan drivers share the same enclosure. Verify electromagnetic compatibility, ambient temperature, and load-current requirements against the Infineon TLE8458 documentation before releasing the module.
Direkomendasikan
Distributed Automotive Sensor Interface
The TLE8458GUV33XUMA1 is suitable for a compact LIN-connected sensor node that reports measurements to a vehicle controller. Its 1/1 transceiver arrangement supports communication over a single-wire LIN bus, while the integrated 5 V regulator provides a local supply for sensing and signal-conditioning electronics. The 8-pin DSO-8-16 package helps limit PCB footprint in dense wiring harnesses. For reliable operation, place the bypass network near the regulator pins, keep the LIN route compact, and apply the manufacturer’s recommended protection arrangement. Confirm the sensor’s electrical load and the vehicle network’s fault-management requirements before integration.
Direkomendasikan
LIN-Connected Actuator Controller
The TLE8458GUV33XUMA1 can serve as the communication interface for a LIN-connected actuator controller. A host controller uses the LIN physical layer to receive commands, while the actuator’s driver circuitry operates from a local supply. Integrating the 5 V regulator with the transceiver simplifies the low-power side of the design and can reduce component count. The 10.4 kBd rate is suitable for command and status traffic rather than closed-loop motion data. Designers should account for switching transients from the actuator driver, separate sensitive transceiver returns where appropriate, and validate the final network against the manufacturer’s reference recommendations.
Direkomendasikan
Industrial LIN Sensor Network
The TLE8458GUV33XUMA1 can support compact distributed sensor modules in an industrial LIN network that uses the same low-speed single-wire communication concept as automotive LIN. Its 10.4 kBd interface handles supervisory data exchange, and the integrated 5 V regulator supplies local sensing circuitry. The 8-pin surface-mount package is useful in space-constrained instrument housings. Industrial deployment requires review of the device’s specified operating voltage and temperature limits, as well as EMC and network fault tolerance. Add the application-appropriate transient protection and bypass components and confirm them against the manufacturer datasheet before production.
Direkomendasikan
Data referensi engineering untuk TLE8458GUV33XUMA1 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TLE8458GUV33XUMA2 | TLE8458GUV33XA | TLE8458GUV33XUMA1 |
|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-DSO-8-16, 8 pins | PG-DSO-8-16, 8 pins | PG-DSO-8-16, 8 pins | PG-DSO-8-16, 8 pins |
| Product Type | LIN transceiver with integrated voltage regulator | LIN transceiver with integrated voltage regulator | LIN transceiver with integrated voltage regulator | LIN transceiver with integrated voltage regulator |
| LIN Bus Data Rate | 10.4 kBd | 10.4 kBd | 10.4 kBd | 10.4 kBd |
| Transceiver Configuration | 1/1 | 1/1 | 1/1 | 1/1 |
| Integrated Regulator Output | 5 V | 5 V | 5 V | 5 V |
| Terminal Count | 8 terminals | 8 terminals | 8 terminals | 8 terminals |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
Diferensiator Kunci
- Combines the LIN interface and local regulator in one device (vsDiscrete 5 V regulator plus LIN transceiver implementation)
- Matches the standard 10.4 kBd LIN physical-layer rate (vsTLE8458GUV33XUMA2)
- Uses a compact 8-pin surface-mount package (vsTLE8458GUV33XA)
Catatan Desain
Use the Infineon TLE8458 datasheet to select the input supply, output load, and external capacitors for the integrated 5 V regulator. Place the required bypass components directly beside the corresponding pins and use a short, low-impedance ground connection. Verify that the local load remains within the regulator’s specified output-current and thermal limits; these limits are not stated in the component listing.
Keep the LIN bus trace short and route it away from high-current switching nodes and sensitive analog signals. Follow the manufacturer’s recommended external protection arrangement, including the appropriate transceiver and bus components. A compact layout is useful in vehicle modules, but excessive trace length can increase coupling and susceptibility to transient events on the single-wire network.
Do not treat identical package dimensions as proof of drop-in equivalence. The final ordering suffix can change temperature grade, qualification, or delivery information, so compare the complete ordering table, pin descriptions, electrical limits, and package drawing before replacing the TLE8458GUV33XUMA1. Also distinguish this physical-layer transceiver from a LIN controller; a host microcontroller or dedicated protocol device is still required.
Informasi Konformitas
Compliance and qualification attributes are not stated in the manufacturer-family description or distributor records. Confirm them from the exact ordering code in Infineon’s product documentation before release.