TLV2455CN - 220 kHz Quad Rail-to-Rail Op Amp | Texas Instruments
MPN: TLV2455CN ✓ AktifTLV2455CN Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The rail-to-rail input stage accepts signals close to the positive and negative supply rails, while the rail-to-rail output stage can swing close to those limits under suitable load conditions. Within the broader hierarchy, an operational amplifier is a linear amplifier and analog IC used for buffering, amplification, filtering, comparisons, feedback control, and signal conditioning.
The TLV2455CN provides four rail-to-rail amplifiers, 220 kHz gain-bandwidth product, and approximately 23 uA typical quiescent current. These characteristics make it appropriate for general-purpose low-power designs that do not require the bandwidth of a high-speed amplifier. A shutdown function allows the circuit to reduce power consumption when the analog section is inactive. Its PDIP package also supports conventional through-hole assembly, prototyping, and manual inspection.
Each amplifier is designed for conventional closed-loop operation using external feedback components. The combination of low quiescent current and rail-to-rail signal handling allows the device to operate close to its supply limits, reducing the required headroom in portable systems. Configuration resistors and compensation networks should be selected for the intended closed-loop gain because the bandwidth available for stable operation depends on that gain.
Typical uses include low-frequency sensor conditioning, microphone preamplification, current-to-voltage conversion, active filtering, and four-channel buffering. The four independent channels can also implement common analog functions such as two differential amplifiers, two comparators with suitable output saturation limits, or instrumentation-style signal conditioning. The shutdown pin is useful when battery life is more important than maintaining an active analog state.
For PCB design, keep input, feedback, output, and decoupling paths short, and place the power-supply bypass capacitor close to the device. Check input and output swing limits against the actual load and supply voltage. Because each channel is independent, unused amplifiers should be configured in a stable state rather than left with floating inputs.
This product data combines the manufacturer-family characteristics, package information, sourcing metadata, and engineering design guidance to support amplifier selection, PCB implementation, and replacement planning for the TLV2455CN.
Alternatif penggantian untuk TLV2455CN — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TLV2455CN (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type.
TLV2455IN
✅ Drop-InKontak untuk harga
Lihat Datasheet →TLV2455CN Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Circuits | 4 circuits |
| Rail-to-Rail Input | Rail-to-rail |
| Rail-to-Rail Output | Rail-to-rail |
| Gain-Bandwidth Product | 220 kHz |
| Arus Memerintah | 23 uA typical per amplifier |
| Shutdown Function | Yes |
| Package Type | 16-pin PDIP |
| Gaya Mounting | Through-hole |
| Product Category | General-purpose amplifier |
| Number of Inputs | 8 input pins for 4 differential amplifiers |
| Jumlah Output | 4 output pins |
Konfigurasi Pin TLV2455CN
| Pin produk 1 | OUTA — Output of amplifier A |
| Pin produk 2 | -INA — Inverting input of amplifier A |
| Pin produk 3 | +INA — Non-inverting input of amplifier A |
| Pin produk 4 | V- — Negative supply connection |
| Pin produk 5 | +INB — Non-inverting input of amplifier B |
| Pin produk 6 | -INB — Inverting input of amplifier B |
| Pin produk 7 | OUTB — Output of amplifier B |
| Pin produk 8 | OUTC — Output of amplifier C |
| Pin produk 9 | -INC — Inverting input of amplifier C |
| Pin produk 10 | +INC — Non-inverting input of amplifier C |
| Pin produk 11 | V+ — Positive supply connection |
| Pin produk 12 | +IND — Non-inverting input of amplifier D |
| Pin produk 13 | -IND — Inverting input of amplifier D |
| Pin produk 14 | OUTD — Output of amplifier D |
| Pin produk 15 | SHDN — Shutdown control input |
| Pin produk 16 | NC — Not connected |
Aplikasi Umum
TLV2455CN cocok untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Portable Audio Signal Conditioning, Industrial Current-to-Voltage Conversion, Active Filtering and Signal Shaping, Medical Monitoring Interfaces, Automotive Low-Power Control Circuits.
Battery-Powered Sensor Conditioning
The TLV2455CN suits low-power sensor interfaces because each of its four amplifiers has approximately 23 uA typical quiescent current and accepts inputs that approach the supply rails. Place the active channels close to the sensor and use the shutdown control to disable the amplifier section when measurements are not required. Rail-to-rail input operation preserves signal range in compact systems, while the 220 kHz gain-bandwidth product supports low-frequency sensor signals rather than wideband waveform processing.
Direkomendasikan
Portable Audio Signal Conditioning
The TLV2455CN can provide low-frequency microphone preamplification, buffering, and gain stages in portable audio equipment. Its rail-to-rail output capability is useful when the available headroom is limited, and the 220 kHz gain-bandwidth product is appropriate for many voice-band and control-signal paths. Four channels allow shared functions such as input amplification, active filtering, output buffering, and a second gain stage within one 16-pin PDIP package.
Direkomendasikan
Industrial Current-to-Voltage Conversion
The TLV2455CN is well suited to current-to-voltage conversion in industrial instrumentation when the sensor output is small and the measurement bandwidth is limited to the low-frequency range. Its rail-to-rail input stage accommodates transduccer signals near the ends of the supply range, while approximately 23 uA typical quiescent current per channel helps limit power demand. The shutdown pin can deactivate the conversion path between measurement cycles.
Direkomendasikan
Active Filtering and Signal Shaping
The four TLV2455CN channels can implement cascaded active filters, gain stages, and buffers for low-frequency analog signals. A 220 kHz gain-bandwidth product gives design margin above many control, sensor, and audio-band applications, although closed-loop gain and stability requirements must be checked for each topology. Rail-to-rail output operation helps preserve dynamic range, and the shutdown function can reduce consumption when the filter is inactive.
Direkomendasikan
Medical Monitoring Interfaces
The TLV2455CN can support low-frequency front-end stages in medical monitoring equipment, including sensor buffering, gain amplification, and active filtering. Its rail-to-rail input capability is useful for compact systems where the measured signal may occupy much of the available supply range. The approximately 23 uA typical quiescent current supports power-constrained designs, while the shutdown function permits the analog front end to remain inactive between acquisition intervals.
Direkomendasikan
Automotive Low-Power Control Circuits
The TLV2455CN can be evaluated for low-speed automotive control, actuator-driver, and sensor-interface blocks where four low-power amplifier channels are advantageous. Its 220 kHz gain-bandwidth product fits many control-loop and conditioning tasks, and the shutdown control can reduce demand during inactive periods. Automotive qualification is not established by the commercial suffix, so environmental, temperature, lifetime, and AEC-Q100 requirements must be verified before use in a safety-relevant vehicle design.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TLV2455CN — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TLV2455IN |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-pin PDIP | 16-pin PDIP - same package |
| Number of Amplifiers | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 220 kHz | 220 kHz |
| Quiescent Current | 23 uA typical per amplifier | 23 uA typical per amplifier |
| Input Architecture | Rail-to-rail | Rail-to-rail |
| Output Architecture | Rail-to-rail | Rail-to-rail |
| Shutdown Function | Yes | Yes |
| Operating Temperature Grade | CN grade; exact limits not stated | IN grade; exact limits not stated |
Diferensiator Kunci
- Four amplifiers integrated in one package (vsTLV2455IN)
- Low quiescent current for a rail-to-rail quad amplifier (vsTLV2455IN)
- Integrated shutdown control (vsTLV2455IN)
Catatan Desain
Estimate total quiescent current as four times the approximately 23 uA per-amplifier figure when all channels are active, giving about 92 uA before shutdown and load-current effects. This is an arithmetic estimate using the published per-channel value. Actual board demand also includes bias current, feedback-network current, output current, and leakage paths, so measure the completed design across its intended supply-voltage range.
Place the supply bypass capacitor immediately between the V+ and V- pins, with the shortest possible ground return. Route each amplifier's non-inverting input and feedback components away from adjacent high-impedance input nodes to reduce capacitive coupling. Because all four channels share the same package, separation between sensitive input traces and output or digital traces is especially important when the device handles low-level sensor signals.
Do not leave unused amplifier inputs floating. Tie an unused non-inverting input to a defined potential within the input common-mode range and connect its inverting input to the output, creating a stable unity-gain configuration. Also check the shutdown polarity and startup behavior in the manufacturer pin and electrical-characteristics tables before using SHDN as a system-level power-state control.
For gain or filtering stages, keep feedback resistors and compensation components close to their associated amplifier pins. The 220 kHz gain-bandwidth product is sufficient for many low-frequency stages, but higher closed-loop gains reduce bandwidth and can alter stability. Verify the intended gain, phase margin, capacitive loading, and output-swing requirement in simulation before releasing the PCB layout.
Informasi Konformitas
No specific compliance declarations were identified for the exact TLV2455CN ordering code. Check the current manufacturer product documentation and material declarations before using the device in regulated production.