TLV27L1ID - 16V 160kHz RRO Op Amp | TI | Signal Conditioning
MPN: TLV27L1ID ✗ Akhir HidupTLV27L1ID Ringkasan
An operational amplifier is a voltage-controlled differential amplifier that amplifies the difference between two inputs while providing high input impedance and low output impedance. The TLV27L1 belongs to the operational-amplifier hierarchy of analog and mixed-signal ICs. Its rail-to-rail output stage allows the output voltage to approach both supply rails, improving signal range in battery-powered and low-voltage instrumentation.
The 160-kHz gain-bandwidth product supports moderate-frequency gain and filtering tasks, while the 11-uA nominal channel current suits low-power designs. The family operates from a minimum supply of 2.7 V and supports supplies up to 16 V. Rail-to-rail output capability is especially useful for sensor interfaces, current measurements, and control loops whose signals can occupy much of the available supply-voltage range.
According to the Texas Instruments TLV27L1 family datasheet, the TLV27Lx devices are micropower rail-to-rail output amplifiers intended as upgrades for TLC27Lx-family applications where additional bandwidth can be obtained at lower quiescent current. The architecture combines a single amplifier channel with rail-to-rail output swing in a compact surface-mount package.
Typical applications include low-cost sensor interfaces, portable measurement systems, industrial control inputs, battery-powered instrumentation, and small-signal conditioning stages. The 8-SOIC package also supports conventional surface-mount assembly and manual inspection. The operating range should be checked against the specific temperature grade and supply conditions used in the finished product.
Decoupling should be placed close to the supply pins, and the input network should avoid excessive capacitance because this micropower amplifier is optimized for low-power operation rather than high capacitive-load drive. Confirm output settling, noise, offset, and stability in the target feedback configuration using the manufacturer’s recommended compensation and test circuits.
This product page combines the family-level electrical characteristics, package information, lifecycle status, pin assignment, drop-in ordering-code analysis, and practical guidance for portable sensing, industrial instrumentation, and low-voltage analog signal-conditioning designs.
Alternatif penggantian untuk TLV27L1ID — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TLV27L1ID (sama faktor bentuk dan footprint).
TLV27L1CD
✅ Drop-InKontak untuk harga
Lihat Datasheet →TLV27L1ID Rating Maksimal & Karakteristik Listrik
| Number of Channels | 1 channel |
| Maximum Supply Voltage | 16 V |
| Minimum Operating Supply Voltage | 2.7 V |
| Gain-Bandwidth Product | 160 kHz |
| Nominal Channel Current | 11 uA per channel |
| Output Swing | Rail-to-rail |
| Paket | 8-pin SOIC |
| Tipe Mounting | Surface mount |
| Product Classification | Standard general-purpose amplifier |
Konfigurasi Pin TLV27L1ID
| Pin produk 1 | NC — Not connected |
| Pin produk 2 | IN− — Inverting input |
| Pin produk 3 | IN+ — Noninverting input |
| Pin produk 4 | V− — Negative supply connection |
| Pin produk 5 | NC — Not connected |
| Pin produk 6 | OUT — Output |
| Pin produk 7 | V+ — Positive supply connection |
| Pin produk 8 | NC — Not connected |
Aplikasi Umum
TLV27L1ID cocok untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Portable Industrial Instrumentation, Low-Voltage Control Loop, Current-Sense Amplification, Precision Data Acquisition Front End, Portable Audio and Interface Level Conditioning.
Battery-Powered Sensor Conditioning
TLV27L1ID fits low-power sensor interfaces because it operates from a minimum supply voltage of 2.7 V and draws 11 uA nominal channel current. Place it in a noninverting or transimpedance configuration when the sensor output is close to ground, using the rail-to-rail output stage to preserve much of the available signal range. The 160-kHz gain-bandwidth product is appropriate for sensors with modest bandwidth rather than fast pulse acquisition. Verify source-impedance limits, input bias current, offset behavior, and stability with the actual sensor resistance before releasing the design.
Direkomendasikan
Portable Industrial Instrumentation
The TLV27L1ID is useful for compact industrial measurement equipment requiring a 2.7-V to 16-V operating supply and modest signal bandwidth. Its single-amplifier 8-SOIC construction simplifies board allocation while rail-to-rail output swing helps represent bipolar or unipolar sensor signals near the supply limits. At 11-uA nominal channel current, it favors portable and distributed instrumentation designs. Check the exact temperature grade, input offset, common-mode limits, and stability with the sensor network because the 160-kHz bandwidth is optimized for general-purpose rather than high-speed precision work.
Direkomendasikan
Low-Voltage Control Loop
TLV27L1ID can amplify error signals in a low-voltage industrial or embedded control loop where 2.7-V operation, low channel current, and rail-to-rail output are useful. The 160-kHz gain-bandwidth product provides useful closed-loop bandwidth for moderate-speed loops, while the output stage can drive an external actuator driver rather than a load directly. Use local supply bypassing and keep feedback components close to the device. Verify gain error, phase margin, output loading, and startup behavior in the final compensation network rather than assuming a generic amplifier configuration will remain stable.
Direkomendasikan
Current-Sense Amplification
TLV27L1ID is suitable for a low-side or high-side current-sense amplifier when the required signal bandwidth remains below its 160-kHz gain-bandwidth product. The rail-to-rail output allows a small shunt-derived voltage to be amplified near either supply limit, and the 11-uA nominal channel current reduces the impact on low-power systems. Confirm whether the shunt common-mode voltage remains within the amplifier’s input limits. Validate gain error, offset, noise, and output settling at the intended shunt resistance and current range.
Direkomendasikan
Precision Data Acquisition Front End
TLV27L1ID can condition inputs to a data-conversion system when low channel current and rail-to-rail output are more important than wide bandwidth. A gain stage followed by an ADC can use the amplifier’s 2.7-V minimum supply and 16-V maximum capability. The 160-kHz bandwidth supports slow sensor and instrumentation signals but is not intended for high-speed sampling front ends. Pay particular attention to input bias current, offset, resistor-generated noise, and settling time. Place the amplifier and its feedback network near the ADC input to minimize sensitive-node capacitance and interference pickup.
Direkomendasikan
Portable Audio and Interface Level Conditioning
TLV27L1ID can serve as a low-power level-conditioning amplifier for portable audio, microphone, or general interface signals when the signal bandwidth is below 160 kHz. Rail-to-rail output swing is useful with 2.7-V class supplies because it increases the usable output range, while 11-uA nominal channel current favors battery-operated equipment. The device is a general-purpose amplifier rather than a low-noise audio part, so noise and distortion must be checked against the target signal. Use short, guarded input paths and verify the chosen feedback network for stability with source capacitance.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TLV27L1ID — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TLV27L1CD |
|---|---|---|
| Manufacturer | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC |
| Number of Channels | 1 channel | 1 channel |
| Maximum Supply Voltage | 16 V | 16 V |
| Minimum Operating Supply Voltage | 2.7 V | 2.7 V |
| Gain-Bandwidth Product | 160 kHz | 160 kHz |
| Nominal Channel Current | 11 uA per channel | 11 uA per channel |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Product Classification | Standard general-purpose amplifier | Standard general-purpose amplifier |
Diferensiator Kunci
- Combines a 160-kHz bandwidth with 11-uA nominal channel current (vsTLV27L1CD)
- Rail-to-rail output supports efficient low-voltage signal range (vsTLV27L1CD)
- Supports operation from 2.7 V to 16 V (vsTLV27L1CD)
Catatan Desain
Place the supply bypass capacitor immediately adjacent to the V+ and V− pins, and route the return current through the same ground region used by the amplifier. Keep the noninverting and inverting input traces short, particularly when sensing low-level signals. A 100-nF ceramic bypass capacitor is a common starting point, subject to the stability and transient-response recommendations in the manufacturer datasheet.
Do not assume rail-to-rail output means the input common-mode range also reaches both rails. Check input voltage limits against the actual 2.7-V to 16-V supply range and the chosen feedback topology. Likewise, the 160-kHz gain-bandwidth product is a small-signal characteristic, not a guaranteed large-signal output-swing rate. Validate both linear range and stability in the final circuit.
Account for input-bias-current error across high-value feedback resistors and sensor source impedances. Lower resistance values can reduce offset caused by bias current but increase current consumption. Keep sensitive input nodes away from switching nodes and provide a quiet ground reference. Validate noise and offset with the actual source impedance because sensor resistance and resistor Johnson noise can dominate the amplifier contribution.
Budget the amplifier’s supply current together with sensor, ADC, and interface loads. The 11-uA nominal channel current is a per-channel figure, so total system current can be materially higher after adding conversion and communication stages. Use the maximum supply current and temperature limits from the manufacturer datasheet for worst-case power budgeting rather than relying only on the nominal channel-current value.
Informasi Konformitas
No explicit compliance declaration for TLV27L1ID was identified in the cited product pages. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with the manufacturer before release.