TS941IDT - Micropower Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS941IDT ✓ AktifTS941IDT Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The amplifier belongs to the voltage-feedback operational-amplifier family within the broader linear-amplifier and signal-processing IC hierarchy. Rail-to-rail output operation allows the output to approach the supply rails more closely than a conventional fixed-headroom amplifier, which can simplify signal-range calculations in low-voltage systems.
Key characteristics of the TS941IDT include one amplifier circuit per package, micropower operation, rail-to-rail output behavior, and a gain-bandwidth product listed at 10 kHz. These attributes make the device applicable to sensor interfaces, low-level signal conditioning, portable instrumentation, and battery-powered products. Its 8-SOIC outline supports conventional surface-mount assembly while providing separate input, output, supply, and feedback connections.
The TS94x-device family is intended for general-purpose precision signal amplification rather than high-speed waveform processing. The 10 kHz gain-bandwidth characteristic favors static or slowly varying signals, including sensor outputs, reference voltages, and slow feedback-control loops. Rail-to-rail output capability improves usable output range, while the single-amplifier package reduces board area when each signal channel requires only one active device.
Typical uses include low-power sensor conditioning, portable measurement systems, analog control loops, and interface stages that operate from limited supply voltages. The device can also support low-current sensing and monitoring circuits where continued operation with low power consumption is valuable. Designers should confirm input common-mode range, output swing, supply limits, noise, offset, and stability requirements against the manufacturer datasheet before selecting it for a new signal chain.
PCB implementation requires care around the feedback network and supply connections. Place input and output decoupling capacitors close to the device, keep feedback-loop routing compact, and provide a low-impedance ground return. Because the TS941IDT is optimized for micropower applications, component tolerances and leakage currents can influence bias-point accuracy, especially when sensing signals close to the supply rails.
This page organizes the available TS941IDT technical information with an application-focused selection guide, drop-in replacement analysis, comparison data, and practical layout guidance. It is intended to help engineers determine whether the TS941IDT's package, bandwidth, rail-to-rail output behavior, and low-power orientation fit the target circuit before committing to a design.
Alternatif penggantian untuk TS941IDT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TS941IDT (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type, Package.
TS941BIDT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
TS941IDT Rating Maksimal & Karakteristik Listrik
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Architecture | Single operational amplifier |
| Tipe Output | Rail-to-rail |
| Power Class | Micropower |
| Gain-Bandwidth Product | 10 kHz |
| Paket | 8-SOIC |
| Tipe Mounting | Surface mount |
| Jumlah Pin | 8 pins |
TS941IDT 8-soic Diamant Konfigurasi Panduan
Konfigurasi pin untuk TS941IDT (8-soic pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk TS941IDT.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TS941IDT cocok untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Portable Measurement Systems, Low-Power Voltage Buffering, Industrial Slow-Control Loops, Low-Level Analog Interface, Precision Low-Frequency Signal Amplification.
Battery-Powered Sensor Conditioning
The TS941IDT fits low-energy sensor interfaces because it combines micropower operation, a single amplifier circuit, and rail-to-rail output voltage swing in an 8-SOIC package. The 10 kHz gain-bandwidth product is appropriate for temperature, pressure, and position sensors whose signals vary much more slowly than the amplifier bandwidth. Place the amplifier near the sensor connection, use a compact feedback network, and confirm that the selected output range covers the required sensor span. Rail-to-rail output behavior can improve utilization of a limited supply, but the exact input common-mode range, quiescent current, and output-swing limits must be checked before final battery-life and accuracy calculations.
Direkomendasikan
Portable Measurement Systems
The TS941IDT is suited to compact, portable measurement systems that amplify low-level analog conditions without requiring the bandwidth of a general-purpose high-speed amplifier. Its 1-circuit 8-SOIC configuration supports independent channels while preserving board area, and the 10 kHz gain-bandwidth product is suitable for slowly changing signals from resistive bridges and instrumentation transducers. Use short, guarded feedback routes to reduce coupling from adjacent circuits, and place the supply bypass capacitor close to the device. The design must account for input offset, bias current, and common-mode limitations when translating small sensor voltages into a useful output range.
Direkomendasikan
Low-Power Voltage Buffering
The TS941IDT can buffer a reference or sensor voltage when the source has insufficient drive capability, while its rail-to-rail output helps preserve signal span in low-voltage systems. The 10 kHz gain-bandwidth product supports static voltage buffering and low-frequency control applications rather than fast transient reproduction. A voltage follower or inverting configuration can be implemented using the conventional operational-amplifier feedback arrangement. Keep the feedback loop compact to reduce parasitic coupling, and verify the output settling requirements for the intended signal rate. Input offset and bias errors must be included in the accuracy budget for high-impedance sources.
Direkomendasikan
Industrial Slow-Control Loops
The TS941IDT is appropriate for slow industrial feedback loops where low power and a compact analog package are more important than wide bandwidth. Its 10 kHz gain-bandwidth product provides ample response for temperature, level, or actuator-position loops with moderate dynamics, while rail-to-rail output operation can increase control headroom. Place the amplifier close to the feedback divider and controller interface to minimize board-level noise pickup. The PCB should provide stable supply bypassing and a continuous ground return. Before deployment, verify that the loop crossover frequency remains comfortably below the device's small-signal bandwidth and that the output can reach the actuator's required operating range.
Direkomendasikan
Low-Level Analog Interface
The TS941IDT is useful as the first active stage between a low-level analog source and a downstream measurement or control circuit. Its 1-circuit 8-SOIC format simplifies per-channel placement, and its 10 kHz bandwidth is sufficient for many process-control and instrumentation signals. The rail-to-rail output characteristic can help retain signal amplitude when operating near a supply limit. Use a stable reference for gain-setting resistors, maintain short feedback paths, and avoid routing the input beside switching nodes. Exact input offset, bias-current, noise, and common-mode specifications should be reviewed to determine whether the source impedance requires a different amplifier architecture.
Direkomendasikan
Precision Low-Frequency Signal Amplification
The TS941IDT can amplify precision, low-frequency signals where 10 kHz gain-bandwidth product is adequate and micropower operation is advantageous. It is suitable for slowly varying instrumentation outputs and low-current sensing paths rather than waveform or communications signals. A useful implementation places the device near the source, uses a high-impedance reference leg to establish gain, and includes local supply bypass. Because gain error at low frequencies depends on open-loop gain and offset, the actual resistor values and measurement bandwidth should be calculated with the manufacturer performance curves. Rail-to-rail output operation provides additional signal margin, subject to load and supply conditions.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TS941IDT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TS941BIDT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
| Output Type | Rail-to-rail | Rail-to-rail |
| Power Class | Micropower | Micropower |
| Gain-Bandwidth Product | 10 kHz | 10 kHz |
| Mounting Type | Surface mount | Surface mount |
| Performance Comparison | Reference device | No measurable difference reported in principal technical parameters |
Diferensiator Kunci
- Directly documented drop-in equivalence (vsTS941BIDT)
- Micropower-oriented rail-to-rail output stage (vsTS941BIDT)
- No PCB footprint change for the documented replacement (vsTS941BIDT)
Catatan Desain
Place the input bypass capacitor, output bypass capacitor, and feedback components close to the TS941IDT pins. Keep the sensitive input node short and avoid routing it parallel to switching-current paths. The 8-SOIC package is easy to assemble, but poor grounding or long feedback loops can degrade a slow analog signal more than expected. Use a solid ground plane and route the output toward the load only after the precision feedback node has been established.
Design the supply network around the device's actual operating current rather than its output-load capability alone. Micropower operation makes TS941IDT attractive for battery systems, but leakage from the sensor, feedback resistors, protection devices, and board contamination can dominate the standby budget. Evaluate the complete bias current with the intended source impedance and supply voltage, and use high-value resistors only where offset, bias current, and thermal effects remain acceptable.
Do not treat rail-to-rail output as proof that the input accepts every signal near the supply rails. Confirm the input common-mode range, maximum supply voltage, output load capability, and input offset in the manufacturer datasheet. Also verify that the signal bandwidth is well below the 10 kHz gain-bandwidth product and that the feedback network is stable with the intended capacitive loading.
For a voltage follower, keep the output-to-inverting-input route very short and place any output isolation resistor close to the amplifier. This minimizes capacitance at the sensitive node and helps preserve stability. When driving longer cables or higher-capacitance loads, validate the transient response on the assembled board because parasitic loading can interact with the amplifier's compensation and the application's feedback network.
Informasi Konformitas
The available technical listings do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements from the manufacturer product documentation before regulatory use.