TUSB216RWBT - 3-Channel 480Mbps USB 2.0 Redriver | Texas Instruments
MPN: TUSB216RWBT ✓ AktifTUSB216RWBT Ringkasan
A USB signal conditioner is an interface IC placed between a USB host or device and a cable or connector when transmission losses threaten signal integrity. It belongs to the hierarchy of USB interface IC, redriver, repeater, signal-conditioning IC, and semiconductor. The TUSB216 improves a degraded high-speed channel while leaving low-speed and full-speed signal characteristics unaltered, allowing original USB behavior to be retained.
The principal benefits are three-channel high-speed signal conditioning, support for USB 2.0 high-speed operation at 480 Mbps, USB On-The-Go compatibility, and integrated DCP and CDP controllers. The manufacturer states that the device can help a system pass USB 2.0 high-speed near-end eye compliance with a cable as long as 5 meters. The BC 1.2 controller can be enabled through a control pin, adding battery-charging negotiation to the same interface device.
The third-generation signal-conditioning architecture addresses both AC loss caused by capacitive loading and DC loss caused by resistive loading. This makes the device relevant to cable, connector, PCB-trace, and adapter channels where attenuation or impedance discontinuities can reduce eye opening. Its small package also supports compact peripheral, docking, and embedded USB designs.
Typical uses include USB 2.0 peripheral ports, long-cable connections, docking stations, charging-enabled USB ports, industrial equipment, and embedded systems that must extend USB high-speed reach without changing the host or device controller.
Place the redriver close to the connector or source of channel loss, provide the required bypass capacitance, and route the two USB data pairs as controlled-impedance differential pairs. Confirm connector, cable, and PCB compliance in the final system because signal-conditioning operation cannot correct unrelated protocol, power, or routing defects.
This page combines the device's USB interface characteristics, exact-package constraints, application guidance, and sourcing information. It also distinguishes verified engineering facts from parameters that require confirmation against the manufacturer datasheet before schematic release or production qualification.
Alternatif penggantian untuk TUSB216RWBT — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Tidak ada alternatif pengganti yang tersedia untuk produk ini.
Permintaan AlternatifTUSB216RWBT Spesifikasi
| Product Type | USB 2.0 high-speed signal conditioner with BC 1.2 controller |
| Number of Channels | 3 channels |
| Maximum USB High-Speed Data Rate | 480 Mbps |
| USB Interface Generation | USB 2.0 high speed |
| Supported USB Signal Speeds | Low Speed and Full Speed |
| Signal Conditioning | AC-loss and DC-loss compensation |
| Battery Charging Controller | BC 1.2 |
| Charging Port Modes | DCP and CDP |
| USB On-The-Go Compatibility | Compatible |
| Maximum Stated Cable Length | 5 m |
| Paket | 12-X2QFN |
| Package Dimensions | 1.6 mm x 1.6 mm |
| Tipe Mounting | Surface mount |
TUSB216RWBT 1.6 mm x 1.6 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk TUSB216RWBT (1.6 mm x 1.6 mm pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk TUSB216RWBT.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
TUSB216RWBT cocok untuk 6 aplikasis: USB 2.0 Docking Stations, Long USB Cable Adapters, BC 1.2 Charging Ports, Embedded USB Industrial Equipment, USB Peripheral Port Conditioning, USB-to-USB Signal Recovery.
USB 2.0 Docking Stations
The TUSB216RWBT fits docking stations where an internal USB controller connects through long traces, cable assemblies, connector transitions, or repeated interconnects that can reduce USB high-speed eye opening. Its three-channel architecture supports conditioning of multiple USB data paths, while compensation for AC loss caused by capacitive loading and DC loss caused by resistive loading targets the two principal channel-degradation mechanisms. The 480 Mbps capability preserves USB 2.0 high-speed operation, and the 1.6 mm by 1.6 mm 12-X2QFN package helps preserve compactness. Place the device near the affected channel section and verify compliance with the final cable, connector, and PCB stack-up rather than assuming a fixed maximum reach.
Direkomendasikan
Long USB Cable Adapters
The TUSB216RWBT is useful in USB 2.0 cable adapters and extenders where cable capacitance and resistance reduce high-speed signal integrity. The device can compensate for AC loss caused by capacitive loading and DC loss caused by resistive loading, helping restore the differential signal before it reaches the far endpoint. Texas Instruments states that the TUSB216 can help a system pass USB 2.0 high-speed near-end eye compliance with a cable as long as 5 meters. Actual performance depends on cable construction, connector transitions, impedance, and loading, so the complete channel should be tested for eye quality, compliance, and stable enumeration.
Direkomendasikan
BC 1.2 Charging Ports
The TUSB216RWBT supports product designs that require USB data conditioning and battery-charging-port behavior in one device. Its integrated BC 1.2 controller includes DCP and CDP operating modes and can be enabled through a control pin, reducing the number of discrete functions needed around a USB connector. The high-speed path still supports 480 Mbps signaling and channel-loss compensation, while low-speed and full-speed signal characteristics remain unaltered. Designers must coordinate the charging policy with host firmware, source-control logic, and the device power path because the signal-conditioner section and charging controller solve different parts of the port design.
Direkomendasikan
Embedded USB Industrial Equipment
The TUSB216RWBT can improve USB 2.0 connectivity in industrial equipment where internal cable assemblies, panel connectors, or long PCB routes separate a host controller from a peripheral. Its three-channel configuration and 480 Mbps high-speed support allow recovery of degraded USB data transmission without changing low-speed or full-speed behavior. The compact 12-X2QFN package is useful in control systems with limited board area. Industrial implementations should still account for surge, ESD, grounding, cable qualification, and operating-temperature requirements, and should follow the manufacturer layout guidance to prevent the redriver from adding signal-integrity problems of its own.
Direkomendasikan
USB Peripheral Port Conditioning
The TUSB216RWBT is appropriate for a USB 2.0 peripheral port that must operate reliably through a lossy internal channel or external adapter. It compensates intersymbol interference in high-speed traffic by addressing both AC and DC loss, while its patented low-speed and full-speed path does not alter those signal characteristics. This behavior supports broad USB device compatibility while keeping the host and device controllers architecturally unchanged. The small 12-X2QFN footprint is useful for compact peripherals, and the optional BC 1.2 function can serve designs that also expose a charging-capable port. Final qualification should include eye measurement and enumeration testing over the intended cable and connector combinations.
Direkomendasikan
USB-to-USB Signal Recovery
The TUSB216RWBT is suited to USB-to-USB adapters, cable assemblies, and intermediary boards that need to restore a high-speed differential pair after loss from connectors or extended routing. Its three-channel arrangement supports multiple signal paths, and the compensation functions target capacitive AC loss and resistive DC loss separately. At 480 Mbps, the device remains aligned with USB 2.0 high-speed requirements, while low-speed and full-speed behavior is intentionally left unaltered. Place the conditioner close to the point where degradation originates, preserve impedance-controlled routing, and test both near-end and far-end eye behavior. A conditioner cannot correct noncompliant connectors, incorrect device loads, or protocol-level faults.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk TUSB216RWBT — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Catatan Desain
Place the TUSB216RWBT close to the USB connector or the section where signal degradation begins, because the benefit of edge and DC compensation depends on correcting the channel before additional losses accumulate. Route each USB data pair as a controlled-impedance differential pair with consistent spacing, minimal stubs, and no unnecessary layer transitions. Follow the manufacturer pin-description table and recommended application circuit when assigning the 12-X2QFN connections.
Validate the complete USB channel with eye measurements rather than relying only on a nominal cable-length claim. The TUSB216 addresses AC loss from capacitive loading and DC loss from resistive loading, but it cannot correct a noncompliant source impedance, an incorrect connector, an overmated receptacle, or unstable device loading. Test near-end and far-end masks across the intended cable, connector, PCB, and power conditions before production release.
Use the manufacturer-recommended supply connection and decoupling arrangement, including placement of the input bypass capacitor directly beside the relevant device pins. Keep the high-speed return path continuous and avoid splitting ground-plane continuity beneath the redriver. Confirm the actual supply limits, current behavior, and capacitor selection from the official datasheet before schematic freeze because those values are not stated in the product summary.
Do not assume that every TUSB2xx device is a drop-in equivalent. The TUSB216 integrates a particular combination of USB 2.0 high-speed conditioning, low-speed and full-speed behavior, and BC 1.2 control. Other family members can differ in channel count, feature set, package dimensions, and pin assignment. Treat the TUSB216RWBR as a related ordering variant and verify its suffix-specific ordering information before using it as a procurement alternate.
Informasi Konformitas
The available product and distributor information does not explicitly state the requested compliance statuses. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations in the manufacturer product documentation before qualification.