Texas Instruments

TUSB216RWBT - 3-Channel 480Mbps USB 2.0 Redriver | Texas Instruments

MPN: TUSB216RWBT ✓ Active
12-X2QFN Package 480 Mbps Speed
MOQ: 1 |

TUSB216RWBT Overview

The Texas Instruments TUSB216RWBT is a three-channel USB 2.0 high-speed signal conditioner and redriver that operates up to 480 Mbps in a 12-X2QFN package measuring 1.6 mm by 1.6 mm. Designed to compensate for intersymbol interference caused by channel loss, it includes AC-loss compensation, DC-loss compensation, and a configurable USB Battery Charging 1.2 controller.

A USB signal conditioner is an interface IC placed between a USB host or device and a cable or connector when transmission losses threaten signal integrity. It belongs to the hierarchy of USB interface IC, redriver, repeater, signal-conditioning IC, and semiconductor. The TUSB216 improves a degraded high-speed channel while leaving low-speed and full-speed signal characteristics unaltered, allowing original USB behavior to be retained.

The principal benefits are three-channel high-speed signal conditioning, support for USB 2.0 high-speed operation at 480 Mbps, USB On-The-Go compatibility, and integrated DCP and CDP controllers. The manufacturer states that the device can help a system pass USB 2.0 high-speed near-end eye compliance with a cable as long as 5 meters. The BC 1.2 controller can be enabled through a control pin, adding battery-charging negotiation to the same interface device.

The third-generation signal-conditioning architecture addresses both AC loss caused by capacitive loading and DC loss caused by resistive loading. This makes the device relevant to cable, connector, PCB-trace, and adapter channels where attenuation or impedance discontinuities can reduce eye opening. Its small package also supports compact peripheral, docking, and embedded USB designs.

Typical uses include USB 2.0 peripheral ports, long-cable connections, docking stations, charging-enabled USB ports, industrial equipment, and embedded systems that must extend USB high-speed reach without changing the host or device controller.

Place the redriver close to the connector or source of channel loss, provide the required bypass capacitance, and route the two USB data pairs as controlled-impedance differential pairs. Confirm connector, cable, and PCB compliance in the final system because signal-conditioning operation cannot correct unrelated protocol, power, or routing defects.

This page combines the device's USB interface characteristics, exact-package constraints, application guidance, and sourcing information. It also distinguishes verified engineering facts from parameters that require confirmation against the manufacturer datasheet before schematic release or production qualification.

Drop-in alternatives for TUSB216RWBT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

No drop-in alternatives available for this product.

Request Alternatives

TUSB216RWBT Specifications

Product Type USB 2.0 high-speed signal conditioner with BC 1.2 controller
Number of Channels 3 channels
Maximum USB High-Speed Data Rate 480 Mbps
USB Interface Generation USB 2.0 high speed
Supported USB Signal Speeds Low Speed and Full Speed
Signal Conditioning AC-loss and DC-loss compensation
Battery Charging Controller BC 1.2
Charging Port Modes DCP and CDP
USB On-The-Go Compatibility Compatible
Maximum Stated Cable Length 5 m
Package 12-X2QFN
Package Dimensions 1.6 mm x 1.6 mm
Mounting Type Surface mount

TUSB216RWBT 1.6 mm x 1.6 mm Pin Configuration Guide

Pin configuration for TUSB216RWBT (1.6 mm x 1.6 mm package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

1.6 mm x 1.6 mm package pinout diagram for TUSB216RWBT

No detailed pinout data available for TUSB216RWBT.

Refer to the datasheet for full pin configuration.

Typical Applications

TUSB216RWBT is suitable for 6 applications: USB 2.0 Docking Stations, Long USB Cable Adapters, BC 1.2 Charging Ports, Embedded USB Industrial Equipment, USB Peripheral Port Conditioning, USB-to-USB Signal Recovery.

🌐

USB 2.0 Docking Stations

The TUSB216RWBT fits docking stations where an internal USB controller connects through long traces, cable assemblies, connector transitions, or repeated interconnects that can reduce USB high-speed eye opening. Its three-channel architecture supports conditioning of multiple USB data paths, while compensation for AC loss caused by capacitive loading and DC loss caused by resistive loading targets the two principal channel-degradation mechanisms. The 480 Mbps capability preserves USB 2.0 high-speed operation, and the 1.6 mm by 1.6 mm 12-X2QFN package helps preserve compactness. Place the device near the affected channel section and verify compliance with the final cable, connector, and PCB stack-up rather than assuming a fixed maximum reach.

🔧

Long USB Cable Adapters

The TUSB216RWBT is useful in USB 2.0 cable adapters and extenders where cable capacitance and resistance reduce high-speed signal integrity. The device can compensate for AC loss caused by capacitive loading and DC loss caused by resistive loading, helping restore the differential signal before it reaches the far endpoint. Texas Instruments states that the TUSB216 can help a system pass USB 2.0 high-speed near-end eye compliance with a cable as long as 5 meters. Actual performance depends on cable construction, connector transitions, impedance, and loading, so the complete channel should be tested for eye quality, compliance, and stable enumeration.

⚡

BC 1.2 Charging Ports

The TUSB216RWBT supports product designs that require USB data conditioning and battery-charging-port behavior in one device. Its integrated BC 1.2 controller includes DCP and CDP operating modes and can be enabled through a control pin, reducing the number of discrete functions needed around a USB connector. The high-speed path still supports 480 Mbps signaling and channel-loss compensation, while low-speed and full-speed signal characteristics remain unaltered. Designers must coordinate the charging policy with host firmware, source-control logic, and the device power path because the signal-conditioner section and charging controller solve different parts of the port design.

🏭

Embedded USB Industrial Equipment

The TUSB216RWBT can improve USB 2.0 connectivity in industrial equipment where internal cable assemblies, panel connectors, or long PCB routes separate a host controller from a peripheral. Its three-channel configuration and 480 Mbps high-speed support allow recovery of degraded USB data transmission without changing low-speed or full-speed behavior. The compact 12-X2QFN package is useful in control systems with limited board area. Industrial implementations should still account for surge, ESD, grounding, cable qualification, and operating-temperature requirements, and should follow the manufacturer layout guidance to prevent the redriver from adding signal-integrity problems of its own.

📱

USB Peripheral Port Conditioning

The TUSB216RWBT is appropriate for a USB 2.0 peripheral port that must operate reliably through a lossy internal channel or external adapter. It compensates intersymbol interference in high-speed traffic by addressing both AC and DC loss, while its patented low-speed and full-speed path does not alter those signal characteristics. This behavior supports broad USB device compatibility while keeping the host and device controllers architecturally unchanged. The small 12-X2QFN footprint is useful for compact peripherals, and the optional BC 1.2 function can serve designs that also expose a charging-capable port. Final qualification should include eye measurement and enumeration testing over the intended cable and connector combinations.

🖥️

USB-to-USB Signal Recovery

The TUSB216RWBT is suited to USB-to-USB adapters, cable assemblies, and intermediary boards that need to restore a high-speed differential pair after loss from connectors or extended routing. Its three-channel arrangement supports multiple signal paths, and the compensation functions target capacitive AC loss and resistive DC loss separately. At 480 Mbps, the device remains aligned with USB 2.0 high-speed requirements, while low-speed and full-speed behavior is intentionally left unaltered. Place the conditioner close to the point where degradation originates, preserve impedance-controlled routing, and test both near-end and far-end eye behavior. A conditioner cannot correct noncompliant connectors, incorrect device loads, or protocol-level faults.

What is the TUSB216RWBT?
The TUSB216RWBT is a Texas Instruments three-channel USB 2.0 high-speed signal conditioner with integrated BC 1.2 charging-port control. According to the manufacturer product page, it compensates for intersymbol-interference signal loss in a transmission channel and can support USB 2.0 high-speed operation up to 480 Mbps. It is packaged in a compact 12-X2QFN measuring 1.6 mm by 1.6 mm.
What are the key specifications of TUSB216RWBT that engineers should know?
The TUSB216RWBT supports three USB data channels, USB 2.0 high-speed signaling at 480 Mbps, AC-loss compensation, and DC-loss compensation. The manufacturer also identifies compatibility with USB On-The-Go and BC 1.2 specifications, including DCP and CDP controllers. Its 12-X2QFN package measures 1.6 mm by 1.6 mm, making the device suitable for compact USB interfaces, adapters, and docking equipment.
What does the TUSB216RWBT signal conditioner correct?
The TUSB216RWBT compensates for both AC loss caused by capacitive loading and DC loss caused by resistive loading in a USB transmission channel. According to Texas Instruments, the high-speed circuitry compensates intersymbol interference while the patented low-speed and full-speed implementation does not alter those signal characteristics. This makes it useful where cable, connector, or PCB loading degrades USB eye quality.
Where can I download the TUSB216RWBT datasheet PDF?
The official TUSB216 datasheet is available from the Texas Instruments literature link at https://www.ti.com/lit/gpn/tusb216. The manufacturer product page at https://www.ti.com/product/TUSB216 provides the device description, ordering information, quality information, and additional support resources. Use the official datasheet for the complete pin description, electrical limits, recommended application circuit, and package drawings.
Where can I find the TUSB216RWBT pinout?
Use the pin-configuration section and package drawing in the official Texas Instruments TUSB216 datasheet to determine the TUSB216RWBT pinout. The public product listing identifies a 12-X2QFN package with 12 positions, but the complete signal, power, ground, and configuration assignments are not reproduced on this page. Confirm every connection against the manufacturer datasheet before laying out the PCB or assembling the device.
Can the TUSB216RWBT help with a long USB cable?
Yes, the TUSB216RWBT is intended to restore signal integrity in lossy USB channels, including long cable paths. According to the manufacturer product page, it can help a system pass USB 2.0 high-speed near-end eye compliance with a cable as long as 5 meters. Actual reach depends on the complete channel, including cable type, connector geometry, PCB routing, impedance, and device loading.
Does the TUSB216RWBT support USB Battery Charging 1.2?
Yes, the TUSB216RWBT includes a configurable BC 1.2 controller with DCP and CDP capability. The manufacturer states that the charging controller can be enabled through a control pin. This allows a USB port to include charging-port behavior in addition to high-speed signal conditioning, although the host-side firmware and system power path must also support the intended charging policy.
What is the difference between the TUSB216RWBT and TUSB216RWBR?
The TUSB216RWBT and TUSB216RWBR identify ordering variants associated with the same TUSB216 device family, with the trailing letter distinguishing the shipment format. Their exact electrical and pin-level equivalence must be confirmed from the manufacturer ordering information before substitution. Because a shipment-format change does not add distinct engineering capability, it should not be selected merely as a second replacement candidate.
What is the best drop-in replacement for TUSB216RWBT?
No independently verified drop-in replacement can be recommended from the available information. A valid replacement must use the same 12-X2QFN footprint, preserve pin-to-pin connectivity, match the three-channel USB 2.0 high-speed function, and provide equivalent AC- and DC-loss compensation. The TUSB216RWBR shipment-format variant is identified, but no second part with documented package, pinout, and functional equivalence has been established.
Can a TUSB216-family device replace the TUSB216RWBT without PCB changes?
A TUSB216-family device can be considered only after its ordering suffix and package drawing are checked against the TUSB216RWBT. The available listing confirms a 12-X2QFN package for TUSB216RWBT, while the related RWBR variant is associated with the same device family. Do not assume that a similarly named TUSB212, TUSB213, TUSB214, or TUSB215 device is pin-compatible because those devices have different feature sets and packages.
When should I choose the TUSB216RWBT instead of another USB redriver?
Choose the TUSB216RWBT when a USB 2.0 channel needs three-channel high-speed conditioning together with an integrated, controllable BC 1.2 charging-port function. Its AC- and DC-loss compensation addresses both capacitive and resistive channel degradation. Select another redriver instead when only edge-rate shaping is required, when low-speed behavior must be actively modified, or when the required protocol, package, and pinout differ.
Is the TUSB216RWBT suitable for docking stations and USB adapters?
The TUSB216RWBT is suitable for docking stations and USB adapters that need extended USB 2.0 reach or recovery from a lossy interconnect. Its three-channel architecture, 480 Mbps high-speed support, 1.6 mm by 1.6 mm package, and compact footprint support space-constrained designs. The BC 1.2 controller can also simplify the addition of charging-port behavior, subject to correct host firmware and power-path design.
Where can I buy TUSB216RWBT and check its current lead time?
Current commercial availability and lead time should be requested through the Request a Quote form on this page. The manufacturer product page provides ordering information, while the verified distributor listing identifies TUSB216RWBT as an orderable 3-channel, 480 Mbps, 12-X2QFN device. Quote requests allow the current channel, quantity, shipment format, and expected delivery requirement to be confirmed for the intended build.
What is the price of TUSB216RWBT?
The current TUSB216RWBT price depends on order quantity, shipment format, and market conditions. Submit the required quantity and target package configuration through the Request a Quote form on this page. The form provides the appropriate commercial channel for a current quotation without inserting a potentially stale price into the technical description or comparing it against an unqualified substitute.
Is TUSB216RWBT in stock?
Inventory status must be confirmed for the exact TUSB216RWBT ordering suffix and requested shipment quantity. Use the Request a Quote form on this page to request current stock confirmation and delivery timing. The manufacturer product page and verified distributor listing establish product availability channels, but they should not be interpreted as a guaranteed warehouse balance for every quantity.
What layout practices are important for the TUSB216RWBT?
Place the TUSB216RWBT close to the USB connector or the section where channel loss becomes significant, and route each USB data pair as a controlled-impedance differential pair with matched spacing and minimal stubs. Keep the data-path return connections short, follow the manufacturer recommended bypass and termination network, and avoid introducing unnecessary layer changes or test pads that disturb differential symmetry.

Engineering reference data for TUSB216RWBT — comparison, design guidance, and compliance information.

Selection Guide

Choose the TUSB216RWBT when a USB 2.0 system needs both three-channel high-speed signal conditioning and an integrated BC 1.2 charging-port controller. Its 480 Mbps capability and AC- and DC-loss compensation make it appropriate for long cables, lossy connectors, dock interconnects, and compact adapters. The 12-X2QFN package helps when board area is limited. Consider another TI TUSB2xx device when the design does not require the TUSB216 combination of high-speed compensation and configurable BC 1.2 control, but verify that candidate separately for channel count, protocol behavior, package, and pinout. No drop-in substitute should be selected without a documented pin-to-pin and electrical comparison. For the exact TUSB216RWBT shipment configuration, use the Request a Quote form to confirm current commercial availability and delivery timing.

Design Notes

Place the TUSB216RWBT close to the USB connector or the section where signal degradation begins, because the benefit of edge and DC compensation depends on correcting the channel before additional losses accumulate. Route each USB data pair as a controlled-impedance differential pair with consistent spacing, minimal stubs, and no unnecessary layer transitions. Follow the manufacturer pin-description table and recommended application circuit when assigning the 12-X2QFN connections.

Validate the complete USB channel with eye measurements rather than relying only on a nominal cable-length claim. The TUSB216 addresses AC loss from capacitive loading and DC loss from resistive loading, but it cannot correct a noncompliant source impedance, an incorrect connector, an overmated receptacle, or unstable device loading. Test near-end and far-end masks across the intended cable, connector, PCB, and power conditions before production release.

Use the manufacturer-recommended supply connection and decoupling arrangement, including placement of the input bypass capacitor directly beside the relevant device pins. Keep the high-speed return path continuous and avoid splitting ground-plane continuity beneath the redriver. Confirm the actual supply limits, current behavior, and capacitor selection from the official datasheet before schematic freeze because those values are not stated in the product summary.

Do not assume that every TUSB2xx device is a drop-in equivalent. The TUSB216 integrates a particular combination of USB 2.0 high-speed conditioning, low-speed and full-speed behavior, and BC 1.2 control. Other family members can differ in channel count, feature set, package dimensions, and pin assignment. Treat the TUSB216RWBR as a related ordering variant and verify its suffix-specific ordering information before using it as a procurement alternate.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The available product and distributor information does not explicitly state the requested compliance statuses. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations in the manufacturer product documentation before qualification.

Related Searches

TUSB216RWBT datasheet TUSB216RWBT datasheet pdf TUSB216RWBT pinout TUSB216RWBT equivalent TUSB216RWBT replacement TUSB216RWBT cross reference TUSB216RWBT price TUSB216RWBT stock Texas Instruments TUSB216RWBT TUSB216 480Mbps USB signal conditioner TUSB216 12-X2QFN pinout TUSB216RWBT USB docking station TUSB216RWBT BC 1.2 controller TUSB216RWBT vs TUSB216RWBR what is the TUSB216RWBT

Related Components & Terms

Texas Instruments TUSB216RWBT TUSB216 USB 2.0 USB high-speed 480 Mbps USB interface IC USB redriver signal conditioner USB repeater USB On-The-Go Battery Charging 1.2 BC 1.2 DCP CDP intersymbol interference AC loss DC loss 12-X2QFN QFN family surface mount semiconductor USB docking station USB cable adapter near-end eye compliance
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details