集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,800+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 650+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,100+ 製品 📁 インターフェースIC 3,100+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 450+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 14 製品

製品 (38,000+)

SY89468UHY - 2:20 1.5 GHz LVDS Clock Fanout | Microchip
SY89468UHY

SY89468UHY - 2:20 1.5 GHz LVDS Clock Fanout | Microchip

The Microchip Technology SY89468UHY is a 2:20 LVDS fanout buffer with a 2:1 differential input multiplexer, operating from a 2.5 V ±5% supply and supporting input clock frequencies up to 1.5 GHz. The device is packaged in a 64-pin TQFP with an exposed pad. It provides twenty LVDS-compatible clock outputs, accepts AC- or DC-coupled differential signals as small as 100 mV (200 mVPP), and guarantees output rise and fall times below 270 ps. A clock fanout buffer is a clock-management IC that distributes one or more source clocks to multiple destinations while preserving signal amplitude, edge timing, and clock polarity. The SY89468UHY belongs to the hierarchy of clock buffers and drivers, clock distribution ICs, timing-control devices, and broader semiconductor components. Its differential multiplexer allows a system to select between two clock inputs before distributing the selected clock across twenty outputs. The key features include a 2:1 differential input multiplexer, a 1:20 fanout ratio, LVDS-compatible outputs, and a maximum listed operating frequency of 1.5 GHz. The internal three-pin termination architecture allows small-amplitude differential inputs without an external termination resistor network in the signal path. Fail-Safe Input behavior is designed to prevent metastable output conditions when the selected differential input fails to a DC voltage. Internally, the part combines a selectable differential input stage, clock distribution circuitry, and twenty low-voltage differential outputs. The output stage is specified for rise and fall times below 270 ps, making it appropriate for high-speed clock-distribution networks. The 2.5 V ±5% supply requirement supports integration into compact, high-speed digital systems while the exposed pad provides a thermal path from the device to the PCB. Typical uses include telecommunications equipment, industrial control systems, data-conversion equipment, high-speed computing, network timing, and instrumentation. A single SY89468UHY can feed twenty clock destinations when one selected differential source is sufficient, while the multiplexer supports source redundancy or clock switching between two domains. Care is required to preserve LVDS signal integrity through controlled-impedance routing and correctly terminated differential clock networks. For PCB implementation, place the device close to the clock source, use matched routing for each differential pair, provide a continuous ground reference, and connect the exposed pad to the appropriate ground plane. Verify input amplitude, common-mode voltage, output termination, and downstream rise-time requirements before releasing the layout. This page combines the device function, verified timing and supply characteristics, sourcing guidance, and practical layout considerations to support clock-tree design. It also distinguishes the verified SY89468UHY ordering code from related manufacturer ordering and comparison candidates, helping engineers determine whether a proposed replacement preserves the required footprint and electrical behavior.

見積もり お問い合わせ
SY89826LHY - 1 GHz 22-LVDS Fanout Buffer | Microchip
SY89826LHY

SY89826LHY - 1 GHz 22-LVDS Fanout Buffer | Microchip

The Microchip Technology SY89826LHY is a 3.3 V precision 1:22 LVDS fanout buffer and translator with a 2:1 input multiplexer, operating up to 1 GHz in a 64-TQFP exposed-pad package. It provides 22 differential LVDS output pairs for distributing precisely aligned, low-skew clock signals across multiple destinations. A clock fanout buffer is a clock-management IC that receives one source clock and generates multiple buffered copies. Clock buffers and drivers belong to the clock and timing IC family, where they provide fanout, translation, isolation, and signal conditioning. The SY89826LHY combines this function with differential signal translation and input multiplexing for systems requiring flexible clock-source selection. The principal features are a 1 GHz operating frequency, 1:22 fanout ratio, 22 differential LVDS output pairs, 2:1 input multiplexing, and a 3.3 V supply. These functions allow one device to select between two input sources and distribute the selected clock to a large number of LVDS receivers while maintaining consistent edge relationships across the output network. The device is intended for low-voltage 3.3 V clock-distribution systems where many receivers require differential clock inputs. Its LVDS outputs suit point-to-point interconnects on circuit boards, backplanes, and rack-level systems. The exposed pad beneath the 64-TQFP package provides a thermal connection to the PCB, while the multiplexed inputs reduce the number of separate source-selection components required in a multi-clock architecture. Typical applications include synchronized computing and networking equipment, communication backplanes, test and measurement systems, industrial control electronics, server clock distribution, and high-speed instrumentation. In each case, the central design objective is to provide many low-skew differential clock outputs from one or two incoming sources. Layout is critical because 22 differential outputs magnify trace-length, impedance, return-path, and crosstalk sensitivity. Follow the pin-description table and recommended decoupling arrangement in the Microchip datasheet, preserve controlled-impedance routing for LVDS pairs, and connect the exposed pad to a low-impedance thermal plane. Validate output skew and signal integrity on the finished board because package and routing effects can influence system-level timing margins. This product page combines the manufacturer's functional description with package, sourcing, comparison, and layout guidance. It also distinguishes true drop-in options from ordering-code variants and documents which electrical details require confirmation from the complete manufacturer datasheet before a production release.

見積もり お問い合わせ
SY89828LHY - 1GHz Dual LVDS Fanout Buffer | Microchip
SY89828LHY

SY89828LHY - 1GHz Dual LVDS Fanout Buffer | Microchip

The Microchip Technology SY89828LHY is a 3.3 V precision LVDS clock fanout buffer and translator with a 1 GHz operating frequency, two 1:10 differential fanout channels, and twenty differential LVDS output pairs. It accepts two differential inputs through a 2:1 input multiplexer and is housed in a 64-pin TQFP package with an exposed pad. The device is intended for systems that require multiple precisely aligned, low-skew clock signals. A clock fanout buffer is a clock-management IC that reproduces one input signal across several outputs. The SY89828LHY belongs to the clock buffer and clock distribution hierarchy, where low-skew fanout helps preserve timing relationships among high-speed digital circuits. Its differential LVDS interface is designed for 3.3 V systems in which numerous destinations must receive coherent signals over controlled low-voltage differential connections. The principal feature is the combination of two 1:10 fanout paths and a 2:1 input multiplexer. According to the manufacturer product description, the part provides twenty differential LVDS output pairs, allowing a compact architecture to distribute clocks across as many as twenty receiver locations. A maximum operating frequency of 1 GHz supports demanding clock-routing requirements while the dual fanout structure reduces the number of separate clock-distribution devices required. The SY89828LHY also functions as an LVDS translator, allowing the buffered signals to be redistributed using the differential signaling format. This combination is useful when one source must feed multiple subsystems whose clocks must remain aligned. The exposed pad in the 64-pin TQFP package provides the primary thermal path for this high-output-count, 1 GHz device, making careful PCB thermal design important. Typical applications include communication equipment, parallel processing systems, test and measurement instrumentation, server or storage clock distribution, and high-speed backplane interfaces. It is particularly relevant where a single differential clock must reach many endpoints without introducing excessive skew between output pairs. System architects can select the active input through the multiplexer and distribute the selected clock across the available LVDS outputs. Layout should use controlled-impedance LVDS routing, symmetrical differential pairs, solid ground-plane continuity, and the exposed pad connected to a low-impedance thermal plane. Decoupling capacitors should be placed close to the supply and ground pins. Because this is a high-speed, high-output-count clock device, connector transitions, unequal pair lengths, and return-path discontinuities can degrade timing and signal integrity even when the nominal clock frequency remains below 1 GHz. This page combines the manufacturer’s device description, verified distributor identification, package details, application-oriented engineering guidance, and replacement availability analysis. It also distinguishes the core SY89828LHY function from the broader clock-buffer category and highlights design decisions that matter when distributing 1 GHz LVDS clocks across many destinations.

見積もり お問い合わせ
SY89829UHY - 2 GHz Dual LVPECL Clock Driver | Microchip
SY89829UHY

SY89829UHY - 2 GHz Dual LVPECL Clock Driver | Microchip

The Microchip Technology SY89829UHY is a 2.5 V or 3.3 V high-performance dual LVPECL clock driver with dual 1:10 fanout, internal input termination, and redundant input switchover in a 64-pin TQFP exposed-pad package. It provides 20 outputs and supports operation up to 2 GHz for distributing precisely aligned, low-skew clock signals across complex digital systems. A clock driver is a specialized digital IC within the clock and timing hierarchy. It receives a reference clock, provides the electrical drive required by transmission lines, and fans that clock across multiple receivers. LVPECL clock drivers use differential positive-referenced emitter-coupled logic to support high-speed point-to-point links. The SY89829UHY combines this differential clock distribution function with multiplexing, internal termination, and redundant switchover in one device. The device can operate as a dual 1:10 fanout buffer or translator or as a single 1:20 arrangement. It accepts LVPECL or LVDS inputs, and its differential architecture is intended for systems requiring aligned outputs and controlled skew. The manufacturer identifies a maximum pin-to-pin skew of 50 ps and maximum part-to-part skew of 200 ps. Internal termination reduces the need for separate input matching components when the associated board-level network requires it. Redundant switchover gives the system two input paths and allows clock-source redundancy without implementing the multiplexing and fanout functions in separate ICs. This architecture can simplify board partitioning in telecom, networking, test equipment, and data-processing platforms. Compared with discrete clock trees, one integrated driver reduces device count, keeps the clock distribution topology centralized, and makes skew control easier to characterize across the complete output network. Typical uses include line-card clock distribution, redundant clock switching in communication equipment, synchronized backplane systems, high-speed test and measurement platforms, and parallel processing systems. At 2 GHz maximum operating frequency, the device is suited to demanding systems, but signal integrity still depends on correct source termination, controlled-impedance routing, appropriate return paths, and compliance with the layout guidance in the manufacturer datasheet. A critical design consideration is the exposed-pad thermal and return-path arrangement. Place the exposed pad on a solid ground plane with short thermal vias and preserve the high-speed differential topology recommended for the package. Account for power-supply noise, input common-mode behavior, output loading, and receiver termination when establishing the system clock budget. This page combines the manufacturer specifications, package details, sourcing structure, design guidance, and documented replacement information for engineers evaluating the SY89829UHY as a high-output-count LVPECL clock-distribution solution.

見積もり お問い合わせ
SY89832UMG - 2.5V 1:4 LVDS Fanout Buffer | Microchip
SY89832UMG

SY89832UMG - 2.5V 1:4 LVDS Fanout Buffer | Microchip

Microchip Technology SY89832UMG is a 2.5 V, 1:4 differential LVDS fanout buffer/translator optimized for high-speed, low-skew clock distribution. The device provides greater than 2.0 GHz throughput, less than 570 ps input-to-output propagation delay, and guaranteed within-device skew below 20 ps across supply-voltage and temperature variation. It is packaged in a 16-VFQFN surface-mount package with an exposed pad and includes internal input termination. An LVDS fanout buffer is a clock-and-timing interface IC that receives one differential signal and reproduces it across four differential outputs. LVDS, or low-voltage differential signaling, supports high-speed data transfer through low-amplitude differential signaling and common-mode noise rejection. Within the broader semiconductor hierarchy, this device is a fanout buffer and translator, both of which fall under clock and timing ICs and support digital-interface clock distribution. The SY89832UMG is designed for applications in which predictable channel-to-channel timing is as important as high throughput. Its guaranteed within-device skew below 20 ps helps maintain alignment among the four outputs, while the less-than-570 ps input-to-Q propagation delay supports deterministic timing-budget analysis. The 2.5 V supply and 2 GHz-class performance suit communications, industrial control, test equipment, and high-speed digital backplane clock networks. Internal input termination reduces the external termination burden on AC-coupled or DC-coupled differential inputs. The device also includes a VREF-AC reference output for AC-coupled applications, as identified by Microchip for the SY89832U family. Because the outputs are generated internally with closely controlled skew, this buffer can reduce the need for external delay-line compensation when distributing a common differential clock. Typical applications include differential clock distribution for high-speed serializers, source-synchronous interface fanout, telecommunications backplanes, FPGA clock networks, and automated test equipment. In each case, system designers must preserve controlled trace geometry and provide a stable low-noise supply so the differential outputs retain their intended timing and signal-integrity behavior. PCB implementation should use symmetrical routing between each differential pair, maintain continuous reference planes, and place decoupling capacitors close to the supply pins. The exposed pad requires a thermal and return-path layout according to the manufacturer's package guidance. Differential input and output return paths should remain short, and test points should not introduce unequal loading across channels. This page combines the manufacturer's SY89832U technical information with application-oriented guidance for LVDS clock distribution, PCB implementation, timing-budget planning, and component selection. It highlights the SY89832UMG's 1:4 fanout, 2.5 V operation, 2 GHz-class throughput, internal termination, and less-than-20 ps within-device skew in a form useful to engineers evaluating high-speed clock architectures.

見積もり お問い合わせ
SY89837UMG - 2GHz 1:8 LVPECL Fanout Buffer | Microchip
SY89837UMG

SY89837UMG - 2GHz 1:8 LVPECL Fanout Buffer | Microchip

Microchip Technology SY89837UMG is a 2 GHz precision clock fanout buffer with a differential 2:1 input multiplexer and eight LVPECL outputs, supplied in a 32-VFQFN exposed-pad package. It accepts CML, LVDS, or PECL inputs, operates from 2.375 V to 3.6 V, and is specified over -40°C to +85°C. Its principal function is to distribute one selected differential clock to eight outputs while rejecting short runt pulses during input switching. A clock fanout buffer is a digital interface IC belonging to the clock and timing IC hierarchy. It provides multiple low-jitter copies of a clock rather than changing the clock frequency. Clock buffers and drivers are used to extend reach, isolate loads, reduce skew, and improve clock distribution in communications, industrial, server, and test systems. The SY89837UMG adds a redundant-input multiplexer intended for systems where a second clock source may take over when the primary source fails. The 1:8 fanout architecture provides eight outputs from one selected input pair. A maximum operating frequency of 2 GHz supports high-speed digital clocking, while the 2:1 differential multiplexer supports source redundancy. The runt pulse eliminator is the defining functional feature: unlike an ordinary input multiplexer, it is designed to prevent short cycles or runt pulses from appearing at the outputs during switchover. This makes the device relevant to clock systems where an incorrect narrow pulse could create a functional fault downstream. The outputs are 800 mV LVPECL-compatible and have guaranteed rise and fall times below 200 ps. LVPECL is a high-speed differential logic family commonly used where low voltage swing and controlled edge rates are useful. The input stage accepts CML, LVDS, and PECL signaling, allowing the device to operate in systems using different clock-source conventions. The 2.375 V to 3.6 V supply range covers both nominal 2.5 V and 3.3 V implementations, subject to the exact operating limits of each selected rail. Typical applications include redundant server and telecommunications clock trees, industrial control systems, high-speed test equipment, network-interface clock distribution, and FPGA or ASIC clocking. The differential multiplexer is particularly useful when two potential clock sources must be combined without exposing downstream logic to runt pulses. The eight outputs can reduce the number of separate fanout stages required in a multi-branch clock architecture. Designers should treat input selection, termination, differential routing, and output impedance as an integrated high-speed signal-integrity task. Keep the differential input and LVPECL output traces short, matched, and continuous over a suitable reference plane, and use the manufacturer pin-description table when assigning every terminal. Validate switchover timing in the complete system because the behavior of the selected clock source, receiver thresholds, and downstream logic affects the observable result. This product summary organizes the SY89837UMG's fanout, multiplexer, logic-level, supply, frequency, package, and environmental characteristics into an application-focused guide. It also distinguishes confirmed device parameters from information that requires confirmation from the manufacturer datasheet before layout, replacement, or production qualification.

見積もり お問い合わせ
SY89853UMG - 2:1 LVPECL Clock Multiplexer | Microchip
SY89853UMG

SY89853UMG - 2:1 LVPECL Clock Multiplexer | Microchip

Microchip Technology SY89853UMG is a precision, low-power dual 2:1 LVPECL clock multiplexer with a maximum operating frequency of 2.5 GHz, housed in a 32-pin VQFN exposed-pad package. It accepts CML, LVDS, or PECL inputs and provides LVPECL outputs, making it suitable for high-speed clock distribution, clock selection, and redundant clock routing systems. A clock multiplexer is an interface IC that selects one clock source from multiple inputs and forwards the selected signal to an output. Clock multiplexers belong to the broader clock and timing hierarchy, alongside clock buffers, clock generators, phase-locked loops, and clock-tree components. Their primary function is to route a stable high-speed clock while helping systems manage source redundancy, test modes, or multiple operating domains. The SY89853UMG combines two selectable 2:1 paths in one package. Its input circuitry supports CML, LVDS, and PECL formats, while its output uses LVPECL levels for compatible high-speed digital systems. The stated 2.5 GHz maximum frequency makes the device appropriate for communications equipment, network interfaces, clock-distribution fabrics, and test-and-measurement platforms operating with high-speed differential clock signals. Microchip describes the device as a precision, low-power dual 2:1 LVPECL multiplexer with internal termination. Differential clock signaling carries data as complementary signals, which helps reduce susceptibility to common-mode noise when the circuit is implemented with controlled impedance and correct termination. Internal termination is especially useful when it matches the transmission-line environment and avoids unnecessary external components. Typical applications include redundant-clock switching in telecommunications equipment, selectable synchronization for data converters, migration between functional blocks operating at different clock rates, and laboratory clock routing. The 32-pin VQFN exposed-pad package also supports compact layouts, although thermal management and via-in-pad construction should be evaluated against the manufacturer's recommended land pattern. When designing around the SY89853UMG, begin with the manufacturer's recommended differential trace geometry and termination arrangement. Confirm that the source amplitude, common-mode voltage, clock frequency, and selected logic standard are compatible with the inputs. Keep clock routing short and return the unused input to a defined state when the multiplexer configuration permits it. This product page combines the confirmed operating characteristics, package information, sourcing workflow, and application guidance for engineers evaluating the SY89853UMG. It also distinguishes the device from true pin-compatible alternatives and provides practical guidance for evaluating whether the mux, rather than a clock generator or buffer, is the correct architectural choice.

見積もり お問い合わせ
SY89873LMG - 2 GHz LVDS Clock Divider | Microchip
SY89873LMG

SY89873LMG - 2 GHz LVDS Clock Divider | Microchip

The Microchip Technology SY89873LMG is a 3.3 V precision programmable clock divider and three-output LVDS fanout buffer packaged in a 16-pin QFN with exposed pad. It operates up to 2.0 GHz output toggle frequency, accepts high-speed differential CML, LVPECL, HSTL, or LVDS clock inputs, and divides the input frequency to generate a frequency-locked lower-frequency clock. A clock divider is a timing IC that reduces an input clock frequency by a controlled ratio while preserving the relationship between the source clock and derived outputs. Clock dividers and fanout buffers belong to the clock and timing IC hierarchy, where they support clock generation, distribution, frequency translation, and programmable timing in communication, networking, and digital processing systems. The SY89873LMG combines division with three LVDS outputs to distribute one divided clock across multiple loads. Key features include support for AC- or DC-coupled differential inputs, a maximum output toggle frequency of 2.0 GHz, a maximum input frequency of 3.0 GHz, and internal input termination. The three-output architecture reduces the need for separate fanout stages, while the programmable divider allows a system clock to be translated to a lower frequency without introducing an unrelated free-running oscillator. Low-skew and low-jitter operation are central requirements for maintaining timing relationships across parallel LVDS clock domains. The device accepts CML, LVPECL, HSTL, and LVDS input standards, allowing it to operate near many high-speed differential clock sources. Its 3.3 V supply and LVDS output interface place it between the clock-generation and receiver stages of a high-speed system. The internal termination feature helps control impedance at the differential input, but the input network and PCB transmission lines still require careful implementation to minimize reflections and maintain signal integrity. Typical uses include clock division and fanout for communications equipment, network-interface subsystems, backplanes, and high-speed digital logic. It can also support clock-tree designs in industrial and test systems where a source clock must be divided before being distributed to multiple LVDS receivers. The device is particularly relevant where several destinations need a common divided clock and predictable relative timing. For PCB implementation, place the SY89873LMG close to the source clock and route the differential input and LVDS outputs as controlled-impedance pairs. Keep the exposed-pad layout consistent with the manufacturer’s recommended thermal and land-pattern guidance. Confirm the selected divider ratio, termination arrangement, and output timing budget during system validation. This product summary combines the manufacturer’s clock-function description with package, interface, frequency, and application context. It also provides selection guidance, design notes, and verified sourcing information to help engineers evaluate the SY89873LMG before integrating it into a precision LVDS clock tree.

見積もり お問い合わせ
SY89874UMG - 2.5 GHz 1:2 Clock Fanout Buffer | Microchip
SY89874UMG

SY89874UMG - 2.5 GHz 1:2 Clock Fanout Buffer | Microchip

Microchip Technology SY89874UMG is a programmable clock divider and fanout buffer that accepts a high-speed differential clock input and produces divided clock outputs for digital logic. The device operates from a 2.375 V to 3.63 V supply, supports input frequencies as high as 2.5 GHz, and is packaged as a 16-VFQFN with an exposed pad. According to Microchip documentation, it can accept CML, LVPECL, LVDS, or HSTL clock inputs and can create a frequency-locked, lower-speed version of the incoming signal. A clock buffer is a digital semiconductor device used to distribute one clock signal to multiple destinations while controlling impedance, edge rate, skew, and loading. Clock divider and fanout buffers belong to the broader clock and timing IC family, where they support clock generation, frequency translation, distribution, and sequencing functions in communications, industrial, and computing systems. This device combines those functions in one package rather than requiring separate divider and fanout stages. Key characteristics include a maximum clock frequency of 2.5 GHz, a programmable divide ratio, low-skew and low-jitter operation, and 2.5 V or 3.3 V LVPECL output capability. The 16-VFQFN exposed-pad package supports compact high-speed layouts while providing a thermal and ground connection beneath the device. Differential clock routing helps reduce susceptibility to common-mode noise, although correct termination and controlled impedance remain essential. The SY89874U family is associated with clock-tree designs that require a lower-speed derivative of a high-frequency source. Typical uses include communications clock distribution, processor and serializer clock conditioning, data-converter clocking, industrial control systems, and test-and-measurement equipment. The differential input can be driven from CML, LVPECL, LVDS, or HSTL-compatible sources when their voltage and termination requirements are satisfied. For layout, route the differential clock pair as a short, tightly coupled pair and place termination close to the receiving device. Keep the output return path continuous and observe the exposed-pad connection requirements in the manufacturer datasheet. Decoupling capacitors should be positioned near the supply and ground pins to minimize supply inductance and edge-rate distortion. This page combines the product identity, manufacturer family information, price-evidence checks, drop-in cross-reference results, and application-focused design guidance. It also distinguishes the verified SY89874UMG ordering code from the SY89874U family entry and identifies where additional datasheet parameters must be checked before release to production.

見積もり お問い合わせ
SY89875UMG - 2 GHz 1:2 LVDS Clock Buffer | Microchip
SY89875UMG

SY89875UMG - 2 GHz 1:2 LVDS Clock Buffer | Microchip

Microchip Technology SY89875UMG is a 2.5 V programmable clock divider and 1:2 fanout buffer designed for high-speed differential clock distribution. It supports any differential input, including CML, HSTL, LVDS, and LVPECL, and provides two LVDS outputs in a 16-VFQFN exposed-pad package. The device operates across a 2.375 V to 2.625 V core-supply range and a -40°C to +85°C temperature range. A clock buffer is a clock-and-timing IC that reproduces or redistributes a timing signal while preserving signal integrity, fanout capability, and controlled impedance. The SY89875UMG belongs to the clock-buffer and clock-driver hierarchy, where differential fanout devices support communication links, processor interfaces, test equipment, and other high-speed systems. Its combination of differential input flexibility and LVDS output makes it useful when a source must drive multiple destinations without introducing excessive skew or reflection. The SY89875UMG accepts differential inputs through a termination network exposed at the VT pin. This arrangement allows the circuit to accommodate CML, HSTL, LVDS, and LVPECL source logic. A VREF-AC reference supports AC-coupled applications, while the programmable divider function adds frequency division capability. Maximum operating frequency is 2 GHz, and the 1:2 topology provides two outputs from the differential input. The device is particularly useful when a board must fan a high-speed differential clock out to two receivers while maintaining low-voltage differential signaling. Because LVDS is a current-oriented interface, correct source termination, controlled-impedance routing, and receiver-end placement remain central to reliable signal propagation. The SY89875UMG is intended for 2.5 V systems, so its core supply and interface voltages must be checked against the connected transmitter and receiver specifications before layout release. Typical applications include LVDS clock distribution for high-speed serial communication, source-synchronous interfaces, telecommunications equipment, industrial control systems, and data-conversion platforms. The 2 GHz operating limit supports demanding clock trees, while the programmable divider provides flexibility when the downstream system requires a divided clock rather than a direct fanout. The exposed pad also requires attention to thermal and electrical layout practices. Place input, output, supply, and ground connections according to the manufacturer pin-description table. Keep differential traces tightly coupled, use the manufacturer-recommended termination approach, and provide low-impedance planes for return currents. Treat exposed-pad thermal performance as a function of copper area, via distribution, airflow, and adjacent heat sources rather than as a fixed device property. This page combines device specifications, source links, application guidance, and engineering design notes to support clock-tree architecture decisions. It also distinguishes documented functions from parameters that still require confirmation, helping engineers plan sourcing and schematic review without relying on unsupported assumptions.

見積もり お問い合わせ
Si2166-D60-GMR - DVB-S2X/S2/S Satellite TV Demodulator | Skyworks
Si2166-D60-GMR

Si2166-D60-GMR - DVB-S2X/S2/S Satellite TV Demodulator | Skyworks

The Skyworks Si2166-D60-GMR is a digital satellite TV demodulator IC supporting DVB-S, DVB-S2, and DVB-S2X standards in a single CMOS die, housed in a 48-pin QFN (7x7 mm) package. The part integrates a high-performance blind-scan algorithm for all three DVB-S standards and provides a programmable transport stream output interface compatible with all MPEG decoders and conditional access modules. The "D60" suffix denotes the firmware/die revision supporting DVB-S2X alongside legacy DVB-S/S2 reception. A digital TV demodulator is a baseband processor that recovers MPEG transport streams from a tuner-supplied IF signal. In a typical set-top box (STB) or iDTV front-end, a silicon tuner down-converts the RF satellite signal to a low-IF or zero-IF baseband signal, which the demodulator then decodes, error-corrects (LDPC/BCH for DVB-S2X), and outputs as a serial or parallel MPEG transport stream. The Si2166 family sits at the interface between the analog RF front-end and the digital MPEG decoder, and its standards compliance determines whether the end-product can receive next-generation ultra-HD satellite broadcasts. Key features include integrated blind scan for DVB-S/S2/S2X, on-chip blind-lock functionality, an adaptive equalizer for multi-path and weak-signal conditions, DiSEqC 2.x interface support for LNB control, and a flexible GPIO/I2C host control interface. The device operates from typical 1.2V/3.3V supplies and consumes modest power suitable for multi-tuner STB mainboards. Internal ADC and matched-filter blocks eliminate the need for external analog baseband components. Typical applications include DVB-S2X satellite set-top boxes (zapper, PVR, hybrid), integrated digital televisions (iDTVs), Free-to-Air (FTA) receivers, professional IRD (Integrated Receiver Decoder) equipment, and headend monitoring receivers. Designers pair the Si2166-D60-GMR with a companion wideband satellite tuner such as the Si2183 or Si2141 to form a complete RF-to-TS receive chain. When designing with this part, ensure the host processor supplies a stable 3.3V/1.2V rail with adequate decoupling near the supply pins, and route the IF input as a controlled-impedance 50 ohm microstrip. The host I2C bus runs at up to 400 kHz; verify pull-up sizing for the bus capacitance with the demodulator attached. Use the Skyworks Si2166-D60 firmware loader to update the embedded firmware in production, as the demodulator is firmware-defined. This page synthesizes distributor pricing, firmware variant notes, and drop-in alternatives (Si2166-D60-GM, Si2167-D60-GMR) not consolidated on the manufacturer product page. Engineers can use the comparison_table to evaluate same-package replacements and the design_notes for practical PCB layout and power-rail guidance.

見積もり お問い合わせ
Si5330B-B00205-GM - 1:4 LVDS Clock Buffer 710 MHz 24-QFN
Si5330B-B00205-GM

Si5330B-B00205-GM - 1:4 LVDS Clock Buffer 710 MHz 24-QFN

The Skyworks Solutions Si5330B-B00205-GM is a 1:4 LVDS low-jitter, low-skew clock fanout buffer and level translator operating up to 710 MHz, housed in a 24-pin QFN with exposed pad. It accepts one single-ended or differential input and produces four differential (or eight single-ended) low-jitter LVDS outputs, making it well suited for high-performance PCB clock distribution. A clock buffer is a fanout device that takes one reference clock and produces multiple, phase-aligned copies for routing across a printed circuit board. Within the broader clock-tree hierarchy, the Si5330B sits between an upstream PLL/oscillator (frequency generation) and downstream transceivers, ASICs, FPGAs, or ADCs (clock consumption). Unlike a PLL-based clock generator, a buffer preserves the input frequency exactly and only regenerates the edges, minimizing added jitter and avoiding frequency translation artifacts. Key features include 710 MHz maximum input/output frequency, LVDS output format, 1:4 fanout, integrated input level translation (1.8 V, 2.5 V, or 3.3 V core with separate output-bank supply), and minimal crosstalk with strong supply-noise rejection. The exposed-pad QFN-24 package provides a low thermal resistance path for noise-sensitive systems. The device uses a differential LVDS output stage with internal source-terminated architecture, yielding sub-picosecond additive jitter at typical reference frequencies. Independent VDD pins for the input core and the output bank allow level translation without external circuitry, simplifying mixed-voltage designs. Typical applications include high-speed ADC/DAC sampling clocks, FPGA logic clock distribution, telecom/datacom line-card reference clocks, and PCI Express or serializer/deserializer reference fanout. Its low jitter makes it ideal for any noise-sensitive clock domain that needs a clean, multi-drop copy of a single reference. When designing with the Si5330B, follow the datasheet recommended termination for both LVDS inputs and outputs (typically 100 ohm differential) and decouple each VDD pin with a 0.1 uF ceramic placed as close to the IC as possible. The exposed pad must be soldered to a continuous ground plane for both thermal dissipation and controlled impedance. The custom B00205 ordering code defines the factory-set input/output configuration, so verify the variant matches your board's required direction. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on any single distributor listing.

見積もり お問い合わせ
Si5330B-B00205-GMR - 1:4 LVDS Clock Buffer 710MHz | Skyworks
Si5330B-B00205-GMR

Si5330B-B00205-GMR - 1:4 LVDS Clock Buffer 710MHz | Skyworks

The Skyworks Solutions (formerly Silicon Labs) Si5330B-B00205-GMR is a 1:4 LVDS low-jitter, low-skew fanout clock buffer and level translator housed in a 24-pin QFN-EP (4x4 mm) package. It accepts a single input clock and produces four differential LVDS outputs (or eight single-ended outputs) at frequencies from 5 MHz to 710 MHz, with guaranteed low additive jitter, low skew, and low propagation delay variability. A clock fanout buffer (also called a clock driver or clock distributor) is a semiconductor device that receives one input clock reference and replicates it onto multiple low-skew output clocks. Clock buffers sit in the timing-distribution hierarchy between an upstream PLL/oscillator and downstream loads such as FPGAs, ASICs, ADCs, DACs, and SerDes transceivers. By regenerating edges locally, they isolate the source from load-induced jitter and provide the deterministic phase alignment that high-speed digital links require. Differentiating features of the Si5330B family include a glitchless switching mux for redundant clocking applications, minimal cross-talk between outputs, and superior supply noise rejection that simplifies low-jitter distribution in noisy PCB environments. The device uses advanced CMOS technology, supports independent core and output-bank supply pins for integrated level translation without external circuitry, and accepts CML, HCSL, LVDS, or LVPECL inputs while driving LVDS outputs. The integrated input terminations remove the need for external resistor networks. From an architectural perspective, the Si5330B employs a precision differential input receiver followed by a low-jitter PLL-free fanout tree. Because the device does not synthesize new frequencies (it simply distributes and level-translates), its additive jitter contribution is small enough to preserve overall system margins even at 710 MHz operation. The output drivers are LVDS-compatible, providing the 350 mV swing required by ANSI/TIA/EIA-644 receivers. Typical additive jitter is in the sub-picosecond RMS range. Typical applications include clock distribution in communications infrastructure, redundant clocking for high-availability servers and storage, level translation between PECL/LVDS domains, and PCB-level fanout for FPGA, ASIC, and processor clock inputs. The wide 5-710 MHz operating range covers virtually all common telecom, networking, and computing reference frequencies. When designing with the Si5330B, designers should size the output-bank and core supply decoupling per Skyworks' reference layout and observe the LVDS receiver termination requirements (typically 100 ohm differential). The exposed pad must be soldered to a low-impedance ground plane for thermal and electrical performance. This page synthesizes distributor pricing, drop-in alternatives from the same Skyworks Si5330 family, and practical PCB layout notes not consolidated in the manufacturer datasheet.

見積もり お問い合わせ
Si5341B-B04862-GM - 10-Output Ultra-Low Jitter Clock Generator | Skyworks
Si5341B-B04862-GM

Si5341B-B04862-GM - 10-Output Ultra-Low Jitter Clock Generator | Skyworks

The Skyworks Solutions Si5341B-B04862-GM is a pre-programmed, custom-configured variant of the Si5341B ultra-low jitter any-frequency clock generator family. The device delivers up to 10 differential or single-ended clock outputs at any frequency up to 750 MHz (with <350 MHz jitter-optimized outputs available), in a 64-pin QFN (9x9 mm) package with exposed pad for thermal dissipation. The on-board MultiSynth technology generates independent fractional-N synthesizers per output, allowing non-integer frequency relationships that cannot be realized by integer-N PLLs. A clock generator (also called a frequency synthesizer or PLL-based timing IC) is a mixed-signal integrated circuit that takes one or more low-jitter reference inputs (typically a crystal or LVDS/CMOS reference) and produces one or more precise output frequencies locked to that reference. Within the broader hierarchy it sits as: clock generator -> PLL/VCXO -> timing IC -> power management & signal chain. Unlike a simple clock buffer, a clock generator can translate frequency (e.g., 25 MHz in to 156.25 MHz out), translate format (LVCMOS to LVDS/LVPECL/HCSL/CML), and re-multiply reference, all while adding typically <100 fs RMS phase jitter to the signal. Key features of this Si5341B configuration include typical RMS phase jitter of 50 fs (12 kHz-20 MHz, per the Si5341/40 family datasheet), integrated LDOs that accept a single 1.8V/2.5V/3.3V supply, two differential reference inputs with automatic or manual switching, programmable output slew rate and amplitude, and per-output enable / glitchless start/stop. The device is configured via I2C/SPI and the Skyworks ClockBuilder Pro software. Architecturally the Si5341B combines a low-noise integer-N PLL locking to the reference, a MultiSynth fractional-N divider tree per output, and an output-driver block supporting LVCMOS, LVDS, LVPECL, HCSL, and CML. The MultiSynth architecture eliminates the need for bulky external VCXOs in most applications because any fractional multiplication ratio is supported without integer-boundary spurs. Typical applications include 10G/25G/100G Ethernet PHY clocking, OTN/WDM optical transport line cards, FPGA reference clock trees, broadcast video reference generation, JESD204B/C ADC and DAC sampling clocks, and PCIe Gen3/4/5 clock fan-out. Each output can be set independently so a single Si5341B-B04862-GM can replace multiple crystal oscillators on a high-density PCB. When designing with this part, follow the reference schematic in the Si5341/40 Family Reference Manual exactly. Place the 0.1 µF + 1 µF supply decoupling pair directly at the AVDD/VDD pins, route the reference input traces as 50 Ω controlled-impedance differential pairs, and provide a continuous ground plane beneath the exposed pad with at least 12 thermal vias to the internal layer. This page synthesizes Skyworks datasheet specifications, current distributor pricing as of 2026-10-10, drop-in replacement options within the Si5341/Si5340 family, and practical design notes that complement (but do not replace) the manufacturer documentation.

見積もり お問い合わせ
T1014NSN7MQPA - QorIQ 1.2GHz 64-bit Power Arch MPU | NXP
T1014NSN7MQPA

T1014NSN7MQPA - QorIQ 1.2GHz 64-bit Power Arch MPU | NXP

The NXP T1014NSN7MQPA is a single-core 64-bit Power Architecture communications processor from the QorIQ T1 family, running at 1.2 GHz and housed in a 780-pin FBG BGA (23x23 mm) package. It integrates a single e5500 core with Data Path Acceleration Architecture (DPAA) hardware acceleration, DDR3L/DDR4 memory controllers, PCIe, and 1G/10G Ethernet interfaces for high-performance networking and industrial applications. The 0 °C to 105 °C industrial temperature grade and deep-sleep power mode make it suitable for thermally constrained, always-on networking equipment. A microprocessor (MPU) is a single-chip CPU containing the arithmetic logic unit, control unit, registers, cache, and memory management logic needed to execute operating systems and application workloads. Within the SoC hierarchy, an MPU integrates processor cores with on-chip peripherals (memory controllers, bus fabrics, accelerators, networking MACs), distinguishing it from a microcontroller (MCU) which typically targets control loops with on-chip flash. The T1 series occupies the networking/communications tier of NXP's QorIQ lineup, sitting below the multi-core T2/T4 layerscale parts and above the entry P-series. Key features of the T1014NSN7MQPA include a single 64-bit Power Architecture e5500 core at 1.2 GHz, DPAA for packet parsing, classification, and crypto offload, integrated DDR3L/DDR4 controller with ECC, multiple PCIe Gen2 controllers, 1 Gbit Ethernet and 10 Gbit Ethernet MACs, and a deep-sleep low-power mode. Security is handled by the on-chip SEC engine, and the 780-FBGA package exposes the full T1 serial bus, including SerDes lanes for high-speed networking. The DPAA architecture offloads buffer management, queueing, and cryptographic operations from the e5500 core, allowing line-rate packet processing at lower clock frequencies than software-only designs. Compared with general-purpose SoCs, the T1014NSN7MQPA offers deterministic I/O latency and hardware-accelerated networking, which is essential for router, switch, and security appliance workloads. Typical applications include industrial routers, network switches, security gateways, factory automation controllers, and edge networking appliances. The 23x23 mm package footprint is shared across the T1 series, simplifying PCB layout reuse among T1013, T1014, T1023, and T1024 variants. When designing with the T1014NSN7MQPA, allocate adequate PCB area for the 780-ball FBG BGA, plan thermal management for full-power operation, and verify DDR3L/DDR4 routing and impedance per the NXP hardware design guide. For higher core count or throughput, step up to the dual-core T1024 in the same package.

見積もり お問い合わせ
T1020NSE7MQB - QorIQ T1 2-Core 1.4GHz e5500 SoC | NXP
T1020NSE7MQB

T1020NSE7MQB - QorIQ T1 2-Core 1.4GHz e5500 SoC | NXP

The NXP T1020NSE7MQB is a dual-core QorIQ T1 communications processor featuring two integrated 64-bit e5500 Power Architecture cores running up to 1.4 GHz, packaged in a 780-pin FCBGA (23x23 mm). The part integrates hardware-accelerated cryptography, an integrated Ethernet switch, DDR3L/DDR4 memory controllers, and the Data Path Acceleration Architecture (DPAA) for high-performance packet processing. What is a QorIQ communications processor? QorIQ is a NXP processor family targeting networking, telecom, and industrial infrastructure. The T1 series sits at the lower-power dual-core end of the QorIQ T lineup, positioned between the single-core T1014 and the quad-core T1040/T2080 tier. These SoCs combine general-purpose Power Architecture cores with hardware assist engines (SEC for crypto, DPAA for packet parsing/queueing, and integrated Ethernet MACs/switch), enabling line-rate L2-L4 processing without external lookup engines. They belong to the broader communications processor hierarchy: SoC -> microprocessor -> communications processor -> embedded processor. Key features of the T1020NSE7MQB include dual 64-bit e5500 cores with hardware hypervisor support, integrated 32-bit DDR3L/DDR4 memory controller with ECC, integrated 1G/2.5G Ethernet switch fabric, SEC 4.0 crypto accelerator, DPAA for parsing/classification/queueing, two PCIe Gen2 controllers, and four SerDes lanes for SGMII/XAUI. Operating temperature range is 0C to 105C, targeting industrial and extended-temperature networking equipment. The 780-FCBGA package supports the high-speed SerDes and memory interfaces required for multi-gigabit switching. Architecturally, the T1020 uses the e5500 core, a 64-bit superscalar Power Architecture implementation with out-of-order execution, integrated MMU, and hardware virtualization (hypervisor) extensions. The DPAA subsystem offloads frame parsing, classification, and queue management to dedicated engines, freeing the e5500 cores for control-plane and application-layer processing. SEC 4.0 accelerates AES, 3DES, SHA, RSA, and ECC, supporting IPSec, TLS/DTLS, and MACsec at line rate. The integrated Ethernet switch eliminates an external PHY/bridging device in small-port-count designs. Typical applications include industrial Ethernet switches (managed 8-24 port switches), factory automation gateways, IEC 61850-3 substation controllers, edge routers, and ruggedized industrial control platforms where 1-2 cores are sufficient for control-plane and protocol conversion but packet-plane needs hardware assist. The 0-105C temperature range allows deployment in outdoor enclosures and industrial cabinets. For design planning: plan the PCB for 23x23 mm FCBGA with microvia stack-up; provide at least 4 PCB layers with dedicated ground references for SerDes lanes; allocate thermal copper under the package to dissipate the typical 8-12W TDP at 1.4 GHz; and validate DDR3L/DDR4 topology against the NXP reference design guidelines for signal-integrity. This page synthesizes distributor pricing, drop-in QorIQ alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
T1023NSE7MQA - QorIQ 2xCPU 64-Bit 1.2GHz MPU | NXP | FCBGA-525
T1023NSE7MQA

T1023NSE7MQA - QorIQ 2xCPU 64-Bit 1.2GHz MPU | NXP | FCBGA-525

The NXP T1023NSE7MQA is a QorIQ communications microprocessor that integrates two 64-bit Power Architecture e5500 cores running at 1.2 GHz, packaged in a 525-ball FCBGA at a 19x19 mm body size. It is engineered for networking, telecommunications, and industrial networked applications that require hardware-accelerated packet processing with strong crypto throughput. A microprocessor (MPU) is a single-chip CPU with integrated peripherals and memory interfaces that executes an operating system and application workloads. The QorIQ family sits in NXP's communications processing hierarchy above general-purpose ARM Cortex-A MPUs and below dedicated network ASICs/NPUs; T1-series parts specifically target branch-office routers, industrial gateways, and single-board compute modules. T1023NSE7MQA inherits the Data Path Acceleration Architecture (DPAA) that offloads queue management, encryption, and pattern matching from the cores, freeing CPU cycles for control-plane software. Key features include dual e5500 cores at 1.2 GHz, hardware-accelerated SEC (Security Engine) for IPsec and SSL/TLS offload, integrated 1/10 GbE Ethernet MACs, multi-lane PCIe Gen2 controllers, DDR3L/DDR4 memory controller with ECC, and a 0 to 105 C operating temperature range suitable for industrial environments. The 525-FCBGA package uses a 0.8 mm ball pitch and provides the signal integrity required for 1.2 GHz core clocks and high-speed SerDes lanes. The SoC combines Power Architecture e5500 cores with DPAA accelerators and a high-bandwidth interconnect fabric, allowing deterministic packet throughput at line rates on multiple Gigabit Ethernet ports. DDR3L/DDR4 with ECC support enables reliable memory operation for routing tables and security associations, while SEC 5.x acceleration handles bulk cryptographic workloads. Typical applications include industrial IoT gateways, branch-office routers, industrial firewalls, single-board computers for automation, and protocol-converter appliances. The dual-core configuration supports simultaneous data-plane forwarding and control-plane management, eliminating the need for separate co-processors in compact designs. When designing with this device, allocate a 4-layer or better PCB with controlled-impedance routing for SerDes, DDR, and PCIe lanes; respect the 0.8 mm BGA pitch with microvia stackups. Validate thermal design against the 105 C upper limit because the 19x19 mm package concentrates dissipation under the die. This page synthesizes distributor pricing, drop-in same-family NXP variants, and practical design considerations not consolidated in the manufacturer datasheet.

見積もり お問い合わせ
T1024NSE7MQA - QorIQ Dual-Core 1.2GHz Power Arch SoC | NXP
T1024NSE7MQA

T1024NSE7MQA - QorIQ Dual-Core 1.2GHz Power Arch SoC | NXP

The NXP T1024NSE7MQA is a QorIQ T1 series dual-core communications processor that integrates two 64-bit Power Architecture e5500 cores running at 1.2 GHz, combined with hardware Data Path Acceleration Architecture (DPAA), a SEC crypto engine, DDR3L/DDR4 memory controller, PCIe, and 1/10 GbE networking interfaces, in a 780-pin HFBGA package on a 23x23 mm body with 0 to 105C industrial temperature grade. A communications SoC (System-on-Chip) is an integrated processor that combines CPU cores, memory controllers, hardware accelerators and peripheral interfaces on a single die. QorIQ T1 series SoCs sit within NXP's networking processor hierarchy: application-specific CPU -> embedded communications processor -> SoC -> power-managed networking platform. By integrating DPAA frame queues, SEC encryption, and SerDes for Ethernet and PCIe, the platform eliminates the discrete-asset controller ICs required in legacy designs. Key features include dual e5500 cores up to 1.2 GHz, 64-bit ISA with hypervisor support, an integrated SEC security engine accelerating AES, 3DES, Kasumi, SNOW and public-key algorithms, and built-in DDR3L/DDR4 SDRAM controller with ECC. The HFBGA-780 package exposes 4 SerDes lanes configurable for Aurora, XAUI, PCIe Gen2 and 10 Gigabit Ethernet. Hardware support for IEEE 1588 timestamps, packet parsing and queuing offloads CPU load at line rate. Architecturally the part relies on the Power Architecture e5500 dual-issue superscalar core with symmetric multiprocessing and hardware virtualization hooks. The DPAA engine uses a 16-work-element command queue per BMan/QMan complex for parallel packet dispatch. The integrated SEC block supports both Kasumi and SNOW 3G, suiting the part to LTE control-plane cryptography in addition to wireline IPSec tunnels. Typical applications include industrial control routers, LTE small-cell baseband, fan-less network-attached storage controllers, secure VPN gateways and intelligent IoT gateways. Routing platforms typically pair the T1024NSE7MQA with NXP SGMII PHYs, while control-plane applications use only the SEC block and a small NOR flash footprint. Designers should size decoupling for the HFBGA-780 substrate to keep the 1.2 GHz core within the 0 to 105C thermal envelope, and verify SerDes lane allocation when mapping XFI, PCIe and Aurora on the same SoC. PCB layout must strictly follow the NXP 23x23 mm escape rules for the BGA. This page synthesizes distributor pricing, drop-in alternatives drawn from the QorIQ T1 family, and practical design notes not aggregated on any single manufacturer page.

見積もり お問い合わせ
T1024NSN7PQA - QorIQ Dual-Core 1.4GHz PowerPC MPU | NXP
T1024NSN7PQA

T1024NSN7PQA - QorIQ Dual-Core 1.4GHz PowerPC MPU | NXP

The NXP T1024NSN7PQA is a QorIQ communications processor integrating dual 64-bit Power Architecture e5500 CPU cores running at up to 1.4 GHz, paired with a high-performance data path acceleration architecture (DPAA), in a 780-pin HFBGA 23x23 mm package. According to the verified manufacturer description, it supports DDR3L/DDR4 memory, PCI Express Gen2/Gen3 controllers, 1 GbE and 10 GbE interfaces, and targets commercial/industrial thermal grades (0C to 105C). A QorIQ communications processor is a system-on-chip (SoC) microprocessor built on the Power Architecture instruction set, designed for wired and wireless networking equipment. The T1024 belongs to the QorIQ T1 family, which sits in the broader NXP processor taxonomy as: PowerPC e5500 core -> QorIQ T1 communications SoC -> embedded networking MPU -> Power Architecture processor family. This hierarchy positions it between general-purpose microcontrollers (no integrated networking) and high-end multicore QorIQ T2/T4 processors. Key differentiating specifications include the dual e5500 cores (vs. single-core T1014/T1013), 1.4 GHz frequency, hardware-accelerated packet processing via DPAA, integrated SerDes lanes supporting multiple 1 GbE and 10 GbE ports, and a compact 23x23 mm package that maintains pin compatibility with the quad-core T1042 and even the eight-core T2081 for single-PCB scalability. The 780-ball HFBGA package supports the high I/O count needed for multiple Ethernet, PCIe, and DDR interfaces. Architecturally, the T1024NSN7PQA combines Power Architecture e5500 superscalar cores with NXP's Data Path Acceleration Architecture (DPAA), which offloads packet parsing, queue management, and buffer allocation from the cores. This hardware acceleration is critical for line-rate throughput in routers, switches, and network appliances where software-only packet processing cannot scale. Typical applications include industrial routers and switches, network interface cards (NICs), LTE/5G small cell base stations, industrial IoT gateways, and secure networked embedded appliances requiring deterministic packet throughput. The DDR3L/DDR4 controller supports low-power memory operation for thermally constrained designs. When designing with this processor, careful PCB layout is essential - the 780-ball BGA requires microvia or via-in-pad technology, length-matched DDR traces, and a solid ground/power plane stackup. The commercial/industrial temperature grade (0 to 105C) makes it suitable for indoor and outdoor sealed enclosures but not extended-temperature automotive deployments.

見積もり お問い合わせ
T1042NSE7MQPB - QorIQ 4x e5500 1.2GHz MPU w/ Crypto | NXP
T1042NSE7MQPB

T1042NSE7MQPB - QorIQ 4x e5500 1.2GHz MPU w/ Crypto | NXP

The NXP T1042NSE7MQPB is a QorIQ communications processor featuring four 64-bit e5500 Power Architecture cores running at up to 1200 MHz, integrated with the Data Path Acceleration Architecture (DPAA) and hardware cryptography acceleration, housed in a 780-pin FCBGA package. It supports DDR3L/DDR4 memory with a high-performance interconnect and a rich set of networking peripheral interfaces required for embedded networking and telecommunications systems. A microprocessor (MPU) is a single-chip processing unit that integrates one or more CPU cores, caches, memory controllers, and I/O peripherals onto one die, forming the central compute engine of an embedded system. The QorIQ T1 family sits within NXP's communications processor portfolio above simple microcontrollers and below high-end Layerscape SoCs, serving as a scalable platform for industrial control, printer/market controllers, and entry-level networking equipment where deterministic performance, hardware offload, and industrial temperature grades are required. Key features include four e5500 cores with double-precision floating point, DPAA for packet parsing, queueing, and crypto acceleration, hardware security engines supporting AES, DES, SHA, RSA, and Kasumi, integrated DDR3L/DDR4 controller, multiple Gigabit Ethernet MACs (SGMII/RGMII), PCIe Gen 2 controllers, SATA, USB, and SerDes interfaces, and an extended industrial operating temperature range of 0 to 105 degrees C with the 'PB' speed/grade suffix and the 'MQ' marking denoting 'No Switch' silicon revision. The architecture pairs high-frequency out-of-order execution cores with tightly-coupled DPAA engines, offloading packet classification, encryption, and queue management from the cores. The result is deterministic throughput on routing, IPSec, and deep packet inspection workloads while keeping the application cores free for control-plane tasks. The 780-pin FCBGA package exposes all DPAA ports and SerDes lanes, enabling single-chip designs for managed switches, routers, and industrial gateways without companion communication ASICs. Typical applications include industrial Ethernet switches, routers and gateways, secure network appliances, multi-function printers and imaging systems, factory automation controllers, and smart-grid / IEC 61850 substation equipment. The 0 to 105C operating range and long-life industrial grade make this part a fit for harsh-environment embedded systems requiring 10+ year product lifecycles. When designing with this device, allocate sufficient PCB real-estate for the 780-pin FCBGA and its associated DDR routing, provide adequate thermal relief for sustained 1.2 GHz operation, and follow NXP's reference design guidelines for power sequencing. The 'No Switch' ('N') suffix indicates the device ships without integrated Ethernet switch fabric, so multi-port designs require external PHY or switch companions. This page synthesizes authorized distributor stock, drop-in T1 family alternatives, and practical layout guidance not always visible in the manufacturer datasheet.

見積もり お問い合わせ
T1042NSE7PQPB - QorIQ 4x e5500 1.4GHz MPU | NXP
T1042NSE7PQPB

T1042NSE7PQPB - QorIQ 4x e5500 1.4GHz MPU | NXP

The NXP Semiconductors T1042NSE7PQPB is a QorIQ T1 family communications processor that integrates four 64-bit e5500 Power Architecture cores running at 1400 MHz, with hardware cryptography, DDR3L/DDR4 memory controller, and Data Path Acceleration Architecture (DPAA). It is housed in a 780-ball FC-PBGA (23x23) package and targets industrial temperature ranges (0C to 105C). The device is designed for networked printers and embedded communications applications. A communications processor is a specialized system-on-chip that combines general-purpose CPU cores with hardware offload engines for packet processing, security, and high-speed I/O. Within the broader taxonomy, the T1042 sits at the top of the tree: communications processor -> microprocessor (MPU) -> integrated circuit -> semiconductor. The QorIQ T1 family is a scalable, pin-compatible platform that allows migration down to the dual-core T1022 and up to higher-performance devices such as the T2081, simplifying platform design across product tiers. Key specifications of the T1042NSE7PQPB include four e5500 cores at 1.4 GHz, 32 KB I-cache and 32 KB D-cache per core with 256 KB shared L2 per cluster, integrated SEC cryptography engine, DDR3L/DDR4 memory controller with ECC support, three PCI Express Gen 2 controllers, two SATA 2.0 ports, two USB 2.0 controllers with PHY, two Gigabit Ethernet controllers, and an integrated security engine for IPsec, SSL/TLS, and bulk encryption. The device supports hardware virtualization and implements the DPAA for hardware-assisted queue and buffer management. The architecture combines out-of-order Power Architecture execution with hardware-accelerated data path processing. The e5500 cores implement hardware virtualization through logical partition support and extended interrupt prioritization. The DPAA provides a standardized infrastructure for parallel packet processing, including frame managers, queue managers, and buffer managers that offload packet handling from the cores. Hardware security acceleration includes AES, 3DES, Kasumi, SHA-1/SHA-256, public-key accelerator, and a true random number generator. Typical applications include industrial and networked printers, multi-function peripherals, industrial control and factory automation gateways, ruggedized networking equipment, secure routers and VPN concentrators, and small-form-factor industrial servers. The absence of an integrated Ethernet switch reduces BOM cost for applications that already provide external switching, while the integrated PHYs and SEC engine minimize external component count. When designing with this device, ensure the FC-PBGA-780 substrate has adequate microvia stack-up to route the DDR3L/DR4 byte lanes with matched impedance. The thermal design must account for the 1.4 GHz quad-core power envelope; a heatsink or thermal interface material is recommended at sustained workloads above 70 percent utilization across all four cores. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
T2080NSE8MQB - QorIQ T2 4-Core 1.2GHz e6500 MPU | NXP
T2080NSE8MQB

T2080NSE8MQB - QorIQ T2 4-Core 1.2GHz e6500 MPU | NXP

The NXP Semiconductors T2080NSE8MQB is a QorIQ T2 family communications microprocessor based on the 64-bit Power Architecture e6500 core, delivering four dual-threaded cores running up to 1.2 GHz (eight virtual threads) on a 28 nm process. The device is housed in a 896-ball FCBGA (FCPBGA) package measuring 25x25 mm and targets mid-range networking workloads including routers, switches, and security appliances. A microprocessor (MPU) is an integrated circuit that contains the central processing unit, cache hierarchy, memory controller, and a wide range of on-chip peripherals. Within the broader taxonomy, an MPU sits above a microcontroller (MCU) in computational capability and is below an application processor in feature integration; it belongs to the power management-adjacent silicon layer that bridges the network datapath and software-defined control plane. The T2080NSE8MQB is positioned between quad-core devices such as T1042 and the flagship T4240, offering P4080-comparable compute density at lower power and cost. Key features include four PowerPC e6500 cores with hardware-assisted virtualization and 64-bit addressing, a 1.6 GT/s DDR3/DDR3L memory controller with ECC support, and four 10 Gigabit Ethernet MACs (XFI/KR) plus eight 1 Gbit/s MACs (SGMII). Integrated security engines accelerate IPSec, SSL/TLS, and IEEE 1619 cryptography without host CPU intervention. The integrated SerDes lanes and hardware queue managers support line-rate packet processing while keeping the host core free for control-plane software. Architecturally, the T2080NSE8MQB pairs the e6500 core complex with shared L2 cache, a 256-bit CoreNet coherency fabric, and 20 lanes of SerDes that can be configured as PCI Express Gen 2/3, Serial RapidIO, or 10 GbE/KR. The 28 nm CMOS process keeps typical SoC power within range of conventional airflow cooling and operates across a 0 C to 105 C junction range suitable for industrial networking hardware. Typical applications include enterprise routers and security gateways, multi-service access nodes, network attached storage controllers, industrial firewalls, and LTE/Wi-Fi offload modules. It also serves as a drop-in upgrade for T1042 designs that need additional cores and 10 GbE interfaces, and as a value-engineering alternative to P4080 designs that need to reduce bill of materials. When designing with this device, follow NXP hardware design guides for FCBGA land pattern, SerDes reference clock jitter, and DDR3L fly-by topology. Decoupling must be placed adjacent to each power pin per the reference schematic, and thermal vias are mandatory under the lidless package top to meet the 105 C junction specification under worst-case network load. This page synthesizes distributor pricing, sibling MPN options, and practical board-level design guidance that is not duplicated in the NXP product brief, accelerating BOM decisions and PCB layout review.

見積もり お問い合わせ
T2080NXE8PTB - QorIQ 8x 1.5GHz 64-bit MPU, 4x10GE | NXP
T2080NXE8PTB

T2080NXE8PTB - QorIQ 8x 1.5GHz 64-bit MPU, 4x10GE | NXP

The NXP T2080NXE8PTB is a 28 nm QorIQ T2080 communications processor integrating four PowerPC e6500 dual-threaded cores running at up to 1.533 GHz with eight virtual threads, delivering 8x 1.5 GHz computational throughput for high-end networking and communications workloads. The device integrates four 10 Gigabit Ethernet controllers, an 1.87 GT/s DDR3/DDR3L memory controller with ECC support, hardware-accelerated cryptography, and SerDes lanes supporting multiple interconnect standards. It is packaged in a 25x25 mm 896-ball FCBGA (FC-PBGA) suitable for thermally demanding carrier-grade designs. A communications processor (CP) is a specialized microprocessor that combines general-purpose CPU cores with tightly integrated networking, security, and memory subsystems, occupying a tier between application processors and standalone network ASICs. Within the embedded taxonomy, the T2080 belongs to the QorIQ T2 series, which itself descends from Power Architecture-based communications platforms spanning L2/L3 switches, base stations, and edge routers. The e6500 core brings the architectural lineage of the T4240 flagship into a more power- and pin-efficient package. Key differentiating specifications include the e6500 dual-threaded core (eight hardware threads across four physical cores), 1.87 GT/s DDR3/DDR3L with ECC, four integrated 10 GbE MACs plus additional lower-speed Ethernet, hardware crypto acceleration, and -40C to +105C industrial temperature range support. The combination of 10 GbE MACs with hardware crypto acceleration in a single 28 nm die enables line-rate secure processing without off-chip coprocessors. The T2080 architecture implements the Book-E enhanced Power ISA with hypervisor-aware virtualization, a coherent fabric interconnecting cores and I/O, and queue manager acceleration for buffer descriptors. The integrated security engine supports symmetric ciphers, public-key algorithms, and true random number generation, offloading what would otherwise consume CPU cycles. Dynamic power management scales per-core frequency and voltage independently, allowing designers to trade throughput against thermals in thermally constrained SFP-router and MEC platforms. Typical applications for the T2080NXE8PTB include enterprise routers, multi-service switches, network-attached storage controllers, industrial gateways, LTE/5G small-cell base stations, and network security appliances. The integrated 4x10G plus multi-port 1G/2.5G Ethernet and hardware crypto make it especially suited for IPsec/SSL VPN gateways and line-rate deep-packet inspection systems. A key design consideration is PCB layout for the 896-ball FCBGA - a multilayer PCB with a continuous ground plane beneath the package is required for signal integrity of the multi-GHz SerDes lanes. Designers must also provide robust heatsinking because at 1.533 GHz the T2080 dissipates substantial power; airflow of at least 200 LFM is typically required for full-speed industrial operation. This page synthesizes distributor pricing, drop-in alternatives, design notes, and comparison tables that go beyond the manufacturer datasheet, helping procurement and design teams make informed decisions for next-generation networking platforms.

見積もり お問い合わせ
T2081NSE8PTB - QorIQ T2 4C 1.5GHz 896-FCPBGA | NXP Semiconductors
T2081NSE8PTB

T2081NSE8PTB - QorIQ T2 4C 1.5GHz 896-FCPBGA | NXP Semiconductors

The NXP Semiconductors T2081NSE8PTB is a QorIQ T2 family communications processor built on the 64-bit Power Architecture e6500 core, integrating 4 physical cores that present 8 hardware threads (dual-threaded SMT) at up to 1.533 GHz core frequency. The SoC pairs the CPU complex with a high-bandwidth DDR3/DDR3L memory controller rated at 1.87 GT/s and dual 10 Gigabit Ethernet MACs, plus integrated cryptographic acceleration, all housed in a 896-ball FCPBGA (25x25 mm) package. Operating temperature range is 0C to +105C (extended industrial/communications grade). A QorIQ communications processor is a system-on-chip designed for high-throughput packet processing, line-rate forwarding, and control-plane workloads in networking infrastructure. Within the broader taxonomy it sits as: communications processor -> multicore SoC -> embedded MPU -> microprocessor -> IC. The T series spans the T1 (T1040/T1042, quad-core entry), T2 (T2080/T2081, mid-range octal-thread), and T4 (T4240 flagship) tiers; T2081 is positioned as the smaller-footprint, lower-cost variant of the T2080. Key features include four e6500 dual-threaded cores delivering up to 1.5 GHz / 1.8 GHz core frequency with hardware virtualization (hypervisor) support, a 64-bit DDR3/3L controller with ECC supporting up to 1.87 GT/s, two 10 Gigabit Ethernet ports plus additional 1G/2.5G interfaces, integrated SEC crypto acceleration (SEC 5.x), DPAA packet-processing engines, SerDes for multiple protocol modes, and Trust Architecture 2.x secure boot. The e6500 core implements a 7-stage out-of-order pipeline with hardware threads, allowing eight logical contexts across four cores for parallel packet handling. Manufacturing on 28 nm CMOS process keeps power consumption in a band suitable for fan-cooled line cards while retaining T4240-class architectural features at lower cost. Typical applications include enterprise routers and switches, multi-service gateways, control-plane processing in service-provider equipment, network-attached security appliances, industrial networking, and value-engineering upgrades from P4080 or T1042 designs where pin compatibility enables drop-in scalability. When designing with T2081, the 896-FCPBGA requires careful PCB stack-up with microvia technology, matched-length SerDes routing for the 10GbE lanes, and dedicated DDR3/DDR3L impedance-controlled memory layout; thermal management must account for the 25x25 mm top-side dissipation area. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the QorIQ T series, and practical design notes covering PCB stack-up, SerDes routing, and thermal dissipation that go beyond the manufacturer datasheet alone.

見積もり お問い合わせ