集積回路

LT1013CJG

LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments

The Texas Instruments LT1013CJG is a dual precision operational amplifier with 300 uV maximum input offset voltage, a 0.7 MHz gain-bandwidth product, and a hermetically sealed 8-pin ceramic DIP (CDIP-8) package with 0.300 inch lead pitch. Two amplifiers share one hermetic package, giving instrument-grade amplification in strain-gauge, thermocouple, and 4 mA to 20 mA current-loop signal chains. An operational amplifier (op amp) is a high-gain differential amplifier whose inverting and non-inverting inputs are compared, with feedback defining the closed-loop gain. A precision op amp is a variant optimised for low input offset voltage, low input bias current, and low drift so that small sensor signals are amplified without adding meaningful error. Within the component hierarchy, the LT1013CJG sits as a voltage-feedback amplifier in the family of amplifier ICs, inside the broader class of analog integrated circuits and power-management-adjacent signal-chain devices. Key specifications include a 300 uV maximum input offset voltage, 0.7 MHz gain-bandwidth product, and dual-amplifier configuration in a single hermetic ceramic DIP. The device operates from ±15 V supplies as well as from a single 5 V supply, and it exposes two offset-null pins so that input offset voltage can be trimmed in the circuit rather than accepted as a fixed error. Hermetic ceramic sealing protects the die from moisture and contaminants, which matters in high-reliability and legacy industrial equipment. Architecturally the LT1013CJG is a conventional bipolar voltage-feedback amplifier, which gives it wide supply-voltage swing, low input bias current, and predictable AC behaviour with a single compensation capacitor rather than the auto-zeroed architecture used in chopper-stabilised parts. The result is very low noise at low frequencies with continuous operation across the input range, at the cost of higher offsets than modern auto-zeroed amplifiers. Typical applications include bridge and strain-gauge signal conditioners, thermocouple amplifiers, precision instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multi-stage gain blocks in battery-powered precision instruments. When designing around this device, use the two offset-null pins for trimming and place the compensation capacitor close to the device. Keep the hermetic package away from thermal sources, because gradient across the ceramic can shift offset voltage, and avoid saturating the output near the supply rails in instrumentation front ends. This page combines manufacturer and distributor technical data, drop-in alternatives, comparison parameters, and practical design guidance that are not consolidated in the original datasheet.

見積もりお問い合わせ

LT1013CP

LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments

The Texas Instruments LT1013CP is a dual precision operational amplifier featuring high gain, low supply current, low noise, and a low offset-voltage temperature coefficient, supplied in an 8-pin PDIP (P) package. It operates from a single 4V to 44V supply (or dual ±2V to ±22V supplies), draws only 0.5 mA typical supply current per amplifier, and delivers 150 µV maximum input offset voltage at 25°C (LT1013A grade). The input common-mode range includes ground and the output swings to within a few millivolts of ground while sinking current, eliminating crossover distortion. A dual precision op amp is a two-channel integrated operational amplifier that combines matched transistor pairs and laser-trimmed thin-film resistors to achieve DC accuracy comparable to chopper-stabilized designs while consuming milliwatts of power. Within the broader component taxonomy, dual op amps sit under operational amplifiers -> amplifiers -> analog ICs -> semiconductor. The LT1013 was the first precision dual op amp in the 8-pin industry-standard pinout, upgrading legacy devices such as the MC1458/MC1558, LM158, and OP-221 with significantly lower noise and better DC stability. Key features include 150 µV max input offset voltage (LT1013A) with 2.5 µV/°C max offset voltage temperature coefficient, 0.5 mA typical supply current per amplifier, single-supply operation from 4V to 44V, ground-sensing input range, and output swing to within millivolts of ground. The NPN input stage delivers low input bias current and low voltage noise density suitable for transducer and instrumentation front-ends. Typical applications include battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, 4 mA to 20 mA current-loop transmitters, active filters, multiple limit threshold detection, and instrumentation amplifier building blocks. The wide supply range and ground-sensing inputs make it ideal for single-supply industrial and process-control systems. When designing with this part, observe the input common-mode limit: although the inputs include ground, the upper common-mode limit is approximately 1.5V below the positive rail. Place a 0.1 µF bypass capacitor close to the supply pin and add a 10 µF bulk capacitor on the supply rail to maintain low-impedance power across the LT1013's full bandwidth.

見積もりお問い合わせ

LT1013DD

LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments

The Texas Instruments LT1013DD is a low-power dual precision operational amplifier with a 5 V to 44 V wide supply range, two amplifier channels, and an 8-pin SOIC (D) package. The device is intended for instrumentation, signal-conditioning, filtering, and threshold-detection circuits that operate from low single-supply voltages through substantially higher industrial supply levels. Its precision-oriented design combines high gain, low supply current, low noise, and low offset-voltage temperature coefficient, while the extended supply range supports both single-supply and dual-supply implementations. An operational amplifier is an active analog signal-processing device that uses feedback to amplify the difference between its inverting and non-inverting inputs. The dual LT1013 provides two amplifiers in one package, allowing designers to implement two signal paths without using separate packages. In the broader semiconductor hierarchy, the LT1013DD is an analog integrated circuit, specifically a precision operational amplifier used within instrumentation and embedded signal-conditioning systems. The verified product information identifies the LT1013DD as a standard general-purpose dual amplifier with an 8-SOIC package and a 0 °C to 70 °C operating-temperature range. The TI product-page snippet describes the LT1013D as a low-power device with a 5 V to 44 V wide supply range. The wider LT1013 product page states a 4 V to 44 V supply range, so the exact minimum operating supply for the selected LT1013DD ordering option should be confirmed against the manufacturer datasheet before design release. The LT1013DD is suited to battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA-to-20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple gain blocks. Its dual-channel configuration is useful where two related signals must be conditioned consistently, such as sensor excitation and monitoring or differential and common-reference measurements. Designers should pay particular attention to the SOIC-8 pin mapping, supply bypass capacitors, input common-mode range, output swing, and the operating-temperature limits for this ordering code. The precision characteristics make the device useful for instrumentation, but they do not make it a universal rail-to-rail amplifier. Verify signal levels, noise requirements, load conditions, and stability requirements against the manufacturer datasheet rather than assuming that a substitute is electrically identical. This product page consolidates the verified manufacturer and distributor information, source-backed alternatives, package details, pricing fields, application guidance, and design notes. It is intended to support initial component selection and comparison rather than replace the complete LT1013D datasheet during sign-off.

見積もりお問い合わせ

LT1013DP

LT1013DP - Dual Precision Op Amp, 4-44V, 8-PDIP | TI

The Texas Instruments LT1013DP is a dual precision operational amplifier with a low-power, wide 4 V to 44 V supply range, supplied in an 8-pin PDIP package. The device provides two amplifier circuits in the standard dual-op-amp configuration and is designed for instrumentation and precision signal-conditioning applications. According to the TI product page, the LT1013 family is specified for ±15 V and single 5 V supply operation, while the LT1013D version supports single-supply operation with input voltage range extending to ground and output swing to ground while sinking current. What is a precision operational amplifier? A precision op amp is a voltage-feedback amplifier used to amplify small differential signals while controlling offset, bias current, drift, and output behavior. Within the signal-chain hierarchy, the LT1013DP is a dual amplifier IC that can serve as an instrumentation amplifier building block, a buffer, an active-filter element, or a precision gain stage. Its dual channel count allows two signal paths or a differential signal-conditioning structure in one package. Key verified features include a 4 V to 44 V supply range, dual precision operation, and the industry-standard 8-pin configuration identified by Analog Devices as the first precision dual op amp in that configuration. The LT1013DP is listed by DigiKey as a two-circuit, 8-PDIP amplifier. The Analog Devices product page specifically identifies battery-powered precision instrumentation, strain-gauge signal conditioners, thermocouple amplifiers, instrumentation amplifiers, 4 mA to 20 mA current-loop transmitters, multiple-limit threshold detection, active filters, and multiple-gain blocks as application areas. The LT1013DP is especially relevant where a low-power amplifier must operate across a broad supply range or support single-supply signal paths whose input and output approach ground. Compared with a conventional dual precision amplifier in a different package, its 8-PDIP format favors through-hole prototyping, educational platforms, legacy industrial equipment, and repair assemblies where pin compatibility and mechanical replacement matter. The product family is not limited to ±15 V operation; the verified product description confirms single 5 V operation as well. The principal design trade-off is that a PDIP package is larger and less suitable for high-density surface-mount assemblies than a modern small-outline package. Designers should still verify the exact ordering variant, pinout, common-mode limits, output swing, input bias current, offset voltage, drift, noise, and supply-current limits against the manufacturer datasheet before production release. The verified product family is described as low power, but the precise quiescent-current value is not supplied in the provided web data and should be treated as [DATA_NEEDED: quiescent current]. This page synthesizes the verified LT1013 family descriptions, distributor identification, package information, application references, and cross-reference search results. It distinguishes exact verified facts from parameters that require the full manufacturer datasheet, helping engineers evaluate the LT1013DP for precision instrumentation, bridge sensing, thermocouple signal conditioning, current-loop transmission, filtering, and legacy through-hole amplifier designs.

見積もりお問い合わせ

LT1013IP

LT1013IP - Dual Precision Low-Power Op Amp | Texas Instruments

The Texas Instruments LT1013IP is a dual precision low-power operational amplifier with two amplifier circuits, a bipolar input stage, and an 8-pin PDIP package. It operates from a 4 V to 44 V supply range and is intended for instrumentation, signal-conditioning, and low-power analog systems. The verified distributor data identifies a maximum offset voltage of 550 uV, single-supply input operation extending to ground, and output swing toward ground while sinking current. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The LT1013 belongs to the precision operational-amplifier hierarchy, where low offset voltage and low input bias currents support accurate signal conditioning rather than general switching or high-current drive. Its dual configuration provides two amplifiers in one package, reducing board area when a system needs matched gain stages, buffers, comparators, or active filters. The LT1013IP combines low-power operation with precision-oriented performance. Its wide 4 V to 44 V supply capability makes it useful in industrial instrumentation, battery-powered measurement systems, process-control equipment, and signal-chain modules that operate from elevated supply voltages. The ability to accept inputs near ground supports single-supply measurement circuits, while the ground-referenced output capability supports low-level sensor and current-loop interfaces. The device uses a bipolar input architecture. Compared with rail-to-rail-input amplifiers, the architecture emphasizes precision over operation immediately adjacent to the positive supply rail. Designers should therefore verify the common-mode input range, output swing, load capability, and supply limits against their particular feedback network. The 550 uV maximum offset value reported for the LT1013IP is relevant to sensor-amplifier designs because input offset voltage can become a meaningful error after substantial signal gain. Typical applications include strain-gauge signal conditioning, thermocouple amplification, instrumentation stages, 4 mA-to-20 mA current-loop transmitters, active filters, threshold detection, and multiple gain blocks. Battery-powered precision instrumentation is particularly suitable because the part is identified as a low-power dual operational amplifier while retaining a broad supply range for laboratory, industrial, and communications equipment. For stable operation, place the input and feedback components close to the device, use suitable bypassing at the supply pins, and verify operation across the complete input, output, load, and temperature ranges. Input common-mode and output swing limits must be checked at the lowest and highest expected supply voltages. Negative supply operation may also be available in specific configurations, but the exact operating conditions must be confirmed in the manufacturer datasheet. This page consolidates verified manufacturer and distributor information, pin-compatible alternatives, application guidance, and practical design considerations. It also separates confirmed LT1013IP attributes from electrical parameters that require datasheet verification, helping engineers make sourcing and design decisions without treating unverified values as product facts.

見積もりお問い合わせ

LT1014CJ

LT1014CJ - Quad Precision Op Amp, 50 uV Offset | Analog Devices

Analog Devices LT1014CJ is a four-channel precision operational amplifier with 50 uV input offset voltage, 0.3 uV/°C offset drift, 117 dB common-mode rejection, and 120 dB power-supply rejection, housed in a 14-pin CERDIP package. It operates from dual ±15 V or single 5 V supplies and supports input and output operation down to ground. A precision operational amplifier is a voltage-feedback amplifier designed to amplify small signals accurately while minimizing offset, drift, bias-current error, and power-supply coupling. The LT1014 belongs to the operational-amplifier hierarchy within analog and linear ICs, providing four amplifiers in one package for instrumentation, signal-conditioning, filtering, and threshold-detection circuits. Key features include 50 uV offset voltage, 0.3 uV/°C offset drift, 0.15 nA offset current, an open-loop gain of 8 million, and low supply current of 350 uA. Its 117 dB CMRR and 120 dB PSRR help preserve accuracy when the input signal is small relative to the supply rails. The input common-mode range extends to ground, while the output can swing to ground while sinking current. The LT1014 architecture provides precision performance in four independent amplifier channels. Unlike general-purpose quad amplifiers, its low offset and drift reduce calibration requirements in battery-powered instrumentation, strain-gauge conditioning, thermocouple amplification, current-loop transmitters, active filters, and multiple-limit threshold detection. The manufacturer identifies operation with both ±15 V and single 5 V supplies. The same 14-pin industry-standard configuration as the MC1458/LM348/OP-11/4156 families simplifies upgrades where precision specifications are required. The LT1014CJ is particularly relevant to low-level sensor interfaces where error from input offset or supply variation would otherwise dominate the measurement chain. Designers should verify common-mode and output-swing limits over the complete temperature range, provide suitable bypassing around the supply pins, and account for input-bias-current error when using high-impedance sensors. Exact temperature limits, noise density, slew rate, and package dimensions are not stated in the supplied web data and therefore require confirmation from the manufacturer datasheet. This page combines manufacturer specifications, verified distributor availability, package and pinout information, drop-in family alternatives, application guidance, and transparent data gaps. These engineering-oriented details help buyers assess replacement risk without treating a similar amplifier as automatically equivalent.

見積もりお問い合わせ

LT1014CN

LT1014CN - 4-Channel 5V-44V Precision Op Amp | Texas Instruments

The Texas Instruments LT1014CN is a four-channel precision operational amplifier with a 5 V to 44 V total supply range, 1 MHz gain-bandwidth product, and 14-pin PDIP package. It supports single 5 V operation and dual ±15 V operation, while its input common-mode range includes ground. The device is intended for low-power precision instrumentation, battery-powered measurement systems, strain-gauge amplifiers, thermocouple amplifiers, current-loop transmitters, threshold detectors, and active filters. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. When negative feedback is applied, the closed-loop circuit determines the gain and bandwidth. The LT1014 belongs to the precision operational-amplifier hierarchy, where low offset voltage, low temperature drift, low noise, and low supply current are important for preserving the integrity of small sensor signals. Four amplifiers are integrated into one 14-pin DIP, reducing board area compared with four separate single or dual packages. The LT1014CN provides an input offset voltage of 300 µV maximum at 25 °C and an input offset voltage temperature coefficient of 2.5 µV/°C maximum for the LT1014 family. Its 1 MHz gain-bandwidth product and 0.4 V/µs slew rate support general-purpose precision signal conditioning. Its low-power architecture and 5 V single-supply compatibility are useful when supply energy is constrained. The common-mode input range extends to ground, allowing the device to process signals close to the lower supply rail. The LT1014 uses an industry-standard 14-pin quad operational-amplifier configuration, with four complete amplifier sections and a no-connect position on pin 8. This arrangement supports straightforward printed-circuit-board layout in the familiar PDIP footprint. The device can be used without external compensation in ordinary closed-loop configurations, although gain, noise, output swing, load capability, and stability should be evaluated for each application. Its precision characteristics are more useful than a general-purpose amplifier when sensor outputs are small and drift matters over time. Typical applications include bridge-based strain and pressure measurement, thermocouple signal conditioning, precision current-loop receivers, low-level active filters, multiple-threshold detection, and battery-operated instrumentation. The four independent channels can process several related signals in one package, such as four transducer outputs or a mixed set of amplification, filtering, and comparison functions. The LT1014CN is also useful when both positive and negative supplies are available, because it can operate at dual ±15 V while retaining precision operation. Designers should verify input and output voltage limits, load current, common-mode range, noise, and stability against the worst-case supply voltage and temperature. Input and output decoupling should be placed close to the relevant supply pins, and unused amplifier sections should be configured according to the manufacturer recommendations rather than left floating. Because the package is a PDIP rather than a surface-mount package, it also requires adequate spacing for through-hole assembly and appropriate lead-bend clearance. This product record combines verified manufacturer and distributor information, same-footprint alternatives, pricing status, and practical selection guidance. It highlights the LT1014CN's 5 V to 44 V supply range, four precision channels, 1 MHz bandwidth, 300 µV offset limit, and 14-pin PDIP footprint to support faster engineering selection than a distributor listing alone.

見積もりお問い合わせ

LT1014DN

LT1014DN - Quad Precision Op Amp, 14-PDIP | Texas Instruments

The Texas Instruments LT1014DN is a quad precision operational amplifier in a 14-pin PDIP through-hole package, featuring low offset voltage of 50 µV, 0.3 µV/°C offset drift, and 8 million typical open-loop gain. The device operates from a 5V to 44V wide supply range and supports both dual ±15V and single 5V rails, making it one of the most flexible precision quads for instrumentation designs. An operational amplifier is a high-gain DC-coupled electronic voltage amplifier with differential inputs that produces an output potential relative to ground. Precision op amps such as the LT1014 family are characterized by very low input offset voltage, low bias current, low noise, and high common-mode rejection ratio (CMRR). Within the broader taxonomy, the LT1014 sits at the intersection of instrumentation amplifiers and general-purpose amplifiers, positioned above simple comparators but below specialized zero-drift or chopper-stabilized amplifiers. Its four channels per package make it a workhorse for multi-channel signal conditioning where matched channel-to-channel DC behavior is required. Key specifications include 50 µV maximum offset voltage, 0.3 µV/°C offset drift, 0.15 nA offset current, 117 dB CMRR, 120 dB power supply rejection ratio (PSRR), and a guaranteed 500 µA maximum supply current per amplifier. The output stage swings to within millivolts of both rails, and the common-mode input range includes the negative supply (ground in single-supply operation). Noise performance is 0.55 µV peak-to-peak from 0.1 Hz to 10 Hz, making the LT1014 well-suited for low-frequency precision applications. The LT1014 architecture uses bipolar junction transistor input stages with laser-trimmed thin-film resistors to achieve low offset without external nulling. Notably, no offset null terminals are provided in the quad configuration, which is why the factory-trimmed 50 µV maximum is critical. The combination of low supply current (350 µA typical per amplifier) and 5V minimum supply makes the LT1014 unusually capable for both line-powered instrumentation and battery-powered precision circuits. Typical applications include 4-20 mA current loop transmitters, strain gauge signal conditioners, thermocouple amplifiers, multiple limit threshold detection, active filters, and battery-powered precision instrumentation. The 14-pin PDIP package is favored for breadboard prototyping, laboratory instrumentation, and through-hole industrial designs where socket replacement is desirable. When designing with the LT1014DN, observe that no offset null pins are present, so system offset must be tolerated or corrected downstream. The 14-PDIP package has higher thermal resistance than surface-mount equivalents, so multi-amp loads at high supply voltages may require derating. For new designs where SMT is acceptable, consider the LT1014DSW or similar surface-mount variants. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in a single manufacturer datasheet, with cross-references curated for engineers evaluating multi-channel precision analog front ends.

見積もりお問い合わせ

LT1014IN

LT1014IN - Quad Precision Op Amp, 5V-44V | Texas Instruments

The Texas Instruments LT1014IN is a quad precision operational amplifier with four amplifiers in a 14-pin DIP package, operating from a 5 V to 44 V supply range. It is designed for precision instrumentation, signal conditioning, battery-powered measurement, active filtering, and current-loop interfaces. The device is specified for low offset voltage, low offset-voltage temperature coefficient, high open-loop gain, high common-mode rejection, high power-supply rejection, low supply current, and low noise. According to the Analog Devices data sheet, the LT1014 family provides 50 uV offset voltage, 0.3 uV/°C drift, 8 million gain, 117 dB CMRR, 120 dB PSRR, and approximately 350 uA supply current. The LT1014IN uses the industry-standard 14-pin quad operational-amplifier configuration, making it useful for designs requiring four precision amplifier sections without using four separate packages. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. A precision operational amplifier adds requirements for low input offset, low drift, accurate gain behavior, common-mode rejection, and power-supply rejection. The LT1014 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Its quad configuration provides four amplifiers while reducing package count, board area, and the number of external power connections compared with four single or dual amplifier packages. The principal LT1014 features are its low 300 uV maximum input offset voltage at 25 °C for the LT1014 grade, 2.5 uV/°C maximum offset-voltage temperature coefficient, 8 million open-loop gain, 117 dB common-mode rejection, and 120 dB power-supply rejection. These characteristics are valuable in bridge and strain-gauge amplifiers, thermocouple conditioning circuits, low-current instrumentation, precision filters, threshold detection, and 4 mA-to-20 mA current-loop transmitters. The low 350 uA supply current supports battery-powered instrumentation where every milliamp can affect operating time. The LT1014 can operate from single 5 V supplies as well as dual ±15 V supplies. Its input range extends to ground and its output can swing toward ground while sinking current, which supports single-supply sensing systems where the signal begins near 0 V. The 14-pin DIP package also supports breadboard prototyping, legacy industrial equipment, and through-hole production assemblies. Typical applications include precision sensor interfaces, low-level current measurement, active analog filters, thermocouple amplifiers, process-control instrumentation, and 4 mA-to-20 mA loop transmitters. The device is most appropriate when low offset and drift are more important than the lower cost or higher drive capability of a general-purpose quad amplifier such as an LM324. Designers should verify input common-mode range, output swing, load current, supply current, stability, and noise bandwidth for the intended configuration. Decoupling capacitors should be placed close to the supply pins, and precision resistor networks should use suitable tolerance and temperature-coefficient grades when gain accuracy matters. This page combines the verified LT1014IN manufacturer information, distributor listing, package details, sourced drop-in family alternatives, and practical engineering guidance to support faster component selection and PCB-level implementation.

見積もりお問い合わせ

LT1014MJ

LT1014MJ - 4-Channel 5V-44V Precision Op Amp | Texas Instruments

The Texas Instruments LT1014MJ is a low-power, four-channel precision operational amplifier with a 5 V to 44 V supply range, dual ±15 V operation, and a 14-pin ceramic DIP package. It supports single 5 V and dual ±15 V supplies, operates across -55°C to +125°C, and provides low offset-voltage temperature coefficient, high gain, low supply current, and low noise. The device contains four amplifiers in an industry-standard 14-pin configuration. A precision operational amplifier is a voltage-gain component that uses negative feedback to amplify small voltage differences while maintaining accuracy, stability, and common-mode performance. The LT1014MJ belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and general-purpose analog signal-conditioning ICs. Its common-mode input range includes ground, making it useful in systems where signals approach the lower supply rail. The principal benefits are its combination of precision, low noise, low supply current, and wide operating temperature range. Four independent amplifiers in one package reduce board area and simplify instrumentation systems requiring multiple closely related channels. Operation from a single 5 V supply supports portable and industrial equipment, while dual ±15 V operation accommodates higher-amplitude bipolar signals. The ceramic DIP package provides mechanical robustness for industrial, aerospace, and military-qualified systems operating from -55°C to +125°C. Internally, the LT1014MJ is designed around precision bipolar amplifier stages. The low offset-voltage temperature coefficient helps maintain calibration accuracy as ambient temperature changes, while low noise is valuable for resolving small sensor outputs. Its common-mode input range including ground permits direct sensing of low-level signals without a mid-supply reference, although exact offset voltage, input bias current, noise density, gain-bandwidth product, slew rate, and output-swing limits are not supplied in the verified data and must be checked in the manufacturer datasheet. Typical uses include strain-gauge and thermocouple signal conditioning, battery-powered precision instrumentation, 4 mA to 20 mA current-loop transmitters, active filters, gain blocks, and multiple-limit threshold detection. The four-amplifier organization is especially helpful when a system needs differential input stages, output drivers, or multiple filter sections while maintaining consistent device characteristics. When designing around the LT1014MJ, verify the complete input common-mode range, output swing, supply-current behavior, stability requirements, and offset behavior against the selected supply and load. Decoupling should follow the manufacturer guidance, and exposed inputs must be kept within their valid common-mode range. In low-level instrumentation, input bias-current and source-impedance errors may dominate even when the amplifier itself is precise. This product page consolidates verified manufacturer and distributor information, distinguishes the military-temperature 14-pin CDIP ordering code from related LT1014 variants, identifies packaging-specific drop-in candidates, and adds practical selection guidance. It also makes clear where verified pricing or detailed electrical limits were unavailable rather than substituting estimated values.

見積もりお問い合わせ

LT1016CH

LT1016CH - 10 ns Precision Comparator | Analog Devices

Analog Devices LT1016CH is an ultra-fast precision comparator with a 10 ns propagation delay, direct TTL/CMOS compatibility, and operation from either ±5 V or a single 5 V supply. It is offered in a 10-pin TO-5 package. The device supports complementary outputs, tight offset-voltage specifications, high gain, and an active drive stage capable of driving logic in both output directions. Its combination of speed, precision, and supply flexibility makes it useful in high-speed instrumentation, pulse and timing systems, threshold detection, and applications requiring predictable logic-level interfacing. A comparator is an analog-to-digital interface integrated circuit that compares two input voltages and produces a logic-level result indicating their relative state. In the product hierarchy, the LT1016CH is a comparator within the broader amplifier and interface IC family. Unlike an operational amplifier, a comparator is optimized for rapid binary decisions rather than linear signal amplification. The LT1016CH combines this decision function with low propagation delay and compatibility with common TTL and CMOS logic families. The primary feature of the LT1016CH is its 10 ns response time. This fast transition allows the comparator to resolve input differences with little delay, making it appropriate for pulse-width measurement, zero-cross detection, high-speed thresholding, and timing-reference circuits. The matched complementary outputs allow system designers to use true and inverted logic signals from one device. The manufacturer also specifies tight offset voltage and high gain, supporting precision comparison tasks where input offset can affect the decision point. The LT1016CH can operate from dual ±5 V rails or a single 5 V supply. This operating flexibility is valuable in legacy instrumentation, laboratory equipment, industrial control systems, and mixed-signal designs where negative input or output signal ranges may be required. Its negative-supply quiescent current is specified as 3 mA, and performance is not affected by variations in negative supply voltage. These characteristics simplify power planning in systems where the negative rail is generated from another supply through a resistive divider. Typical uses include high-speed edge detection, pulse-width monitoring, window comparison, oscillator timing, overvoltage detection, and threshold circuits feeding TTL or CMOS logic. The complementary outputs can reduce the need for an additional inverter, while the 10 ns delay supports higher event rates than general-purpose comparators. Care should still be taken to control input overdrive, ringing, output loading, and supply bypassing near the device. For reliable operation, place input and supply bypass capacitors close to the corresponding pins and route high-speed comparator signals over short, controlled-impedance traces. Avoid long unprotected routes between the comparator and receiving logic, and evaluate output behavior with the actual load and supply arrangement. Use the manufacturer pin description and connection diagrams when assigning PCB functions and latch-control logic. This page organizes the LT1016CH specifications, sourcing information, application guidance, and verified drop-in assessment into a practical engineering reference. It also highlights design constraints that matter beyond the headline 10 ns speed, including supply architecture, complementary-output use, latch control, and high-speed PCB implementation.

見積もりお問い合わせ

LT1016CN8

LT1016CN8 - 10ns UltraFast Precision Comparator | Analog Devices

The Analog Devices LT1016CN8 is an UltraFast 10ns precision comparator with matched complementary TTL/CMOS outputs, latch capability, and single 5V or ±5V supply operation, housed in an 8-pin PDIP (N8) through-hole package. A comparator is an analog building block within the voltage-comparator family of linear integrated circuits that compares two input voltages and drives its output to a digital high or low state depending on the input polarity. Comparators sit in the signal-chain hierarchy between operational amplifiers and logic devices, providing the level decision that interfaces continuous analog signals into digital logic such as TTL and CMOS. High-speed comparators like the LT1016 additionally act as timing and data-slicing elements in measurement and communication systems. Key features of the LT1016CN8 include an UltraFast 10ns typical propagation delay, direct TTL/CMOS logic interfacing while operating off ±5V or a single 5V supply, tight input offset voltage and high gain for precision applications, and matched complementary outputs that extend design versatility. The output stage provides active drive in both directions, eliminating the external pull-up required by open-collector comparators and improving edge symmetry. Technical advantages of the LT1016 architecture include no minimum input slew rate requirement, which allows slow-moving signals to be compared reliably, no power supply current spiking during output transitions, which reduces supply noise in sensitive circuits, and a LATCH pin that retains input data at the outputs when held high, enabling peak-detection and sampling functions. Quiescent negative supply current is only 3mA, allowing the negative supply pin to be driven from a resistive divider without affecting performance. Typical applications include fast sampling and sample-and-hold front ends, high-speed A/D converter input comparators, pulse and timing discriminators, and logic-level translation between analog front ends and TTL/CMOS systems. The 200ns acquisition time noted in the datasheet sample-and-hold application exceeds many monolithic sample-and-hold capabilities. A key design consideration is supply configuration: the LT1016 delivers full performance from ±5V or single 5V rails, but output logic levels must be verified against the connected logic family, and the latch pin should be tied appropriately when latching is not used. This page synthesizes verified datasheet parameters, pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

見積もりお問い合わせ

LT1016CN8#PBF

LT1016CN8#PBF - 10ns UltraFast Precision Comparator | Analog Devices

The Analog Devices LT1016CN8#PBF is an UltraFast 10 ns precision comparator that interfaces directly to TTL and CMOS logic while operating from either ±5V or a single 5V supply. Housed in an 8-pin PDIP (N8) through-hole package, the device features tight offset voltage specifications, high gain, matched complementary outputs, and a LATCH pin for retaining input data at the outputs. Quiescent negative supply current is only 3 mA, allowing the negative supply pin to be driven from virtually any voltage through a simple resistive divider without affecting performance. A precision comparator is an analog circuit that compares two input voltages and switches its output based on which is larger, with the speed and accuracy of this decision defining the part's usefulness in instrumentation, data acquisition, and timing applications. Within the broader taxonomy, the LT1016 sits in the linear IC family as a voltage comparator, a sibling category to operational amplifiers, references, and analog multipliers, all serving the analog signal-chain domain of mixed-signal systems. This background is essential when selecting among comparators, op-amps, and ADCs that include internal comparators. Key features of the LT1016CN8#PBF include a 10 ns propagation delay, complementary TTL/CMOS outputs that actively drive in both directions, an input offset voltage typically around 1 mV (max 3 mV at room temperature per the datasheet), and operation from ±5V to a single 5V rail. The unique output stage eliminates cross-conduction during transitions, which reduces dynamic current spikes and simplifies power-supply bypassing. Intern architecture uses a high-slew input stage followed by a regenerative latch and an output driver designed for 50 pF loads with minimal speed degradation. The LATCH pin allows the user to freeze the output state for asynchronous sampling in pipelined systems, and the part operates over the commercial 0°C to 70°C temperature range for the CN8 plastic DIP variant. Typical applications include high-speed A/D converter front-ends, line receivers and zero-crossing detectors, high-frequency triggers, pulse-width modulators, and crystal-oscillator squaring circuits. The matched complementary outputs make the part ideal for driving differential lines or for use as a window comparator when two LT1016s share a reference. Designers should choose low-ESR ceramic bypass capacitors placed within 5 mm of the supply pins to preserve the 10 ns specification; long supply traces add inductance that can cause ringing on the output edge. The negative supply pin may be left floating in single-supply operation, but bypassing is still recommended to keep digital switching currents out of the analog input stage. This page synthesizes distributor pricing, drop-in 8-PDIP alternatives, and practical design notes not found in the manufacturer datasheet alone, giving procurement and design engineers a single reference for sourcing, second-source selection, and board-level implementation of the LT1016CN8#PBF.

見積もりお問い合わせ

LT1016CP

LT1016CP - 10ns UltraFast Comparator | Analog Devices

The Analog Devices LT1016CP is an UltraFast precision comparator with a 10 ns response time, operating from ±5 V or a single 5 V supply in an 8-pin PDIP package. It provides a maximum offset voltage of 3.5 mV, direct TTL/CMOS logic interfacing, and matched complementary outputs for high-speed decision and pulse-width applications. An analog comparator is an integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. Within the broader semiconductor hierarchy, the LT1016 belongs to the comparator class of amplifier and signal-conditioning ICs. Its speed makes it useful wherever a digital system must react to an analog threshold event with minimal delay. Key features include a 10 ns propagation response, tight input-offset specifications, high gain, and active output drive in both logic directions. The device can operate with positive and negative supplies or with a single 5 V rail when the negative supply is generated externally. A latch input retains the comparison result, while matched complementary outputs support complementary clock, edge-detection, and pulse-shaping circuits. The LT1016 uses active bipolar circuitry designed for fast decision-making rather than precision amplification. Its positive and negative input nodes connect directly to the comparison element, and the output stage interfaces with TTL or CMOS logic. The manufacturer datasheet also identifies a quiescent negative-supply current of 3 mA, allowing the negative rail to be produced through a simple resistive divider when only a 5 V supply is available. Typical applications include high-speed threshold detection, zero-crossing detection, pulse-width generation, overvoltage and undervoltage signaling, window comparators, and propagation-delay measurement. The 10 ns response is particularly useful in instrumentation, industrial control, communications, and test systems where the digital output must follow an analog input transition with little delay. When laying out a circuit, keep the comparator inputs and output traces short, provide stable bypassing for the supply pins, and account for input overdrive and output loading. The relatively fast response can magnify noise near the decision threshold, so input filtering and careful grounding can be as important as device selection. This page combines the manufacturer's core operating information with practical placement guidance, application context, and a structured comparison framework. These engineering-focused details help shorten evaluation time while preserving the distinction between electrical equivalence and a true board-level drop-in replacement.

見積もりお問い合わせ

LT1017CH

LT1017CH - Micropower Dual Comparator | Analog Devices

Analog Devices LT1017CH is a micropower dual comparator optimized for low operating power, with two independent comparator channels and an 8-pin TO-5 package. According to the manufacturer datasheet, the LT1017 family can operate from a single 1.1 V cell up to 40 V, making it suitable for battery-powered instrumentation, precision measurement systems, and low-voltage control circuits. The comparator output stage uses a Class B pull-up current source, eliminating the need for an external resistive pull-up. A comparator is an analog semiconductor that compares two input voltages and produces a binary output indicating which input is higher. The LT1017 belongs to the comparator and analog IC hierarchy, where it provides low-power signal conditioning for sensors, thresholds, and control systems. Its micropower operating characteristics are particularly useful when battery energy must be conserved over long operating periods. The dual-channel configuration also allows two comparisons to be performed with one package. The LT1017 is specified for a maximum offset voltage of 1 mV, maximum bias current of 15 nA, typical output drive of 70 mA, and typical supply current of 110 uA for the LT1017. These characteristics support precision threshold detection and low-leakage sensing. The output can also drive loads above V+ with 30 uA of output current, which is useful when the load is connected to a supply rail rather than to ground. Typical applications include battery-powered sensor interfaces, window comparators for industrial controls, low-power monitoring circuits, portable medical equipment, and embedded threshold detection. The wide operating-voltage capability allows the same comparator family to be used with single-cell supplies and substantially higher industrial rails. Care should be taken to maintain adequate input common-mode range, supply sequencing, and output-load limits for the selected configuration. This product page combines the manufacturer datasheet, distributor references, package information, practical application guidance, and qualification boundaries for engineers comparing low-power dual comparators. It emphasizes the known LT1017CH electrical characteristics and identifies application-specific checks that should be completed against the latest datasheet before layout or production release.

見積もりお問い合わせ

LT1022MH

LT1022MH - 26V/us Precision JFET Op Amp | Analog Devices

Analog Devices LT1022MH is a high-speed, precision JFET-input operational amplifier with a 26 V/us typical slew rate, 8.5 MHz gain-bandwidth product, and typically 80 uV input offset voltage. The device is supplied in an 8-terminal, round TO-5 metal package and is identified by the verified distributor data as a military-temperature-grade JFET instrumentation amplifier. A JFET-input operational amplifier is a voltage-feedback amplifier whose input stage uses junction field-effect transistors. The JFET input provides very low input bias current while retaining the low-noise characteristics expected in instrumentation, buffering, and feedback-control circuits. In the product hierarchy, the LT1022MH is a precision operational amplifier, a low-noise amplifier IC, and a semiconductor used to amplify small voltage signals without introducing substantial input loading. The verified specifications highlight a guaranteed slew rate of at least 23 V/us, a maximum input offset voltage of 250 uV, and a maximum offset drift of 5 uV/C. Input bias current is guaranteed at 180 pA at 70 C and 4 nA at 125 C. These characteristics suit high-impedance transducers and precision feedback networks, where low current draw, small offset, and thermal stability are more important than the low cost or low power of a general-purpose amplifier. The 8.5 MHz gain-bandwidth product allows useful closed-loop bandwidth at moderate gains, while the 26 V/us typical slew rate improves large-signal response. The Analog Devices product information states that the output can deliver 20 mA without gain degradation. Together, these ratings make the amplifier useful in precision signal chains where both small-signal accuracy and dynamic range matter. Typical uses include low-level sensor amplification, laboratory instrumentation, photodiode and detector interfaces, active filters, and precision feedback loops. The very low 50 pA typical input bias current at 70 C is especially valuable for high-source-impedance sensors. The military-grade suffix and hermetic-style TO-5 construction are relevant to equipment specified for severe temperature or environmental requirements. The principal design consideration is supply compatibility: the verified excerpts do not state the operating supply-voltage range, so system-level rail selection must be confirmed in the manufacturer datasheet. Decoupling, input common-mode range, output swing, and noise performance must also be checked against the actual circuit rather than inferred solely from speed and offset ratings. This product record combines manufacturer specifications, distributor package information, application guidance, and a strict comparison of same-family drop-in candidates. It is designed to help engineers identify the LT1022MH quickly while preserving the distinction between verified electrical data and parameters that still require confirmation.

見積もりお問い合わせ

LT1028CP

LT1028CP - 75MHz Ultralow-Noise Precision Op Amp | Analog Devices

The Analog Devices LT1028CP is an ultralow-noise, precision, high-speed operational amplifier with a 75 MHz gain-bandwidth product, 10 µV input offset voltage, and 0.1 µV/°C input offset drift. The device is supplied in an 8-pin PDIP package, making it suitable for through-hole precision analog designs. The suffix CP denotes the plastic PDIP-8 ordering option. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1028 belongs to the precision op-amp category, combining high open-loop gain, low offset, low noise, and wide bandwidth. It is used where the measured signal is small and errors introduced by the amplifier must remain below the signal being measured. The LT1028's key features include a 75 MHz gain-bandwidth product, 30 million voltage gain, 10 µV offset voltage, and 0.1 µV/°C offset drift. Analog Devices describes these characteristics as combining ultralow noise with high-speed and precision performance. The result is useful in low-level sensor interfaces, precision filters, audio circuitry, infrared detectors, hydrophone amplifiers, and phase-locked-loop filters. Its speed makes the LT1028 more demanding than a general-purpose op amp. Short feedback paths, careful grounding, suitable bypass capacitors, and attention to capacitive loading help preserve the intended bandwidth and stability. Designers should also verify the power-supply requirements and compensation network against the manufacturer datasheet before applying it to a new board. Typical applications include high-end audio amplification, infrared-detector signal conditioning, hydrophone amplification, active filters, and precision measurement front ends. In these circuits, low noise reduces the circuit's input-referred error, while the 75 MHz bandwidth supports signal processing beyond the bandwidth of many precision amplifiers. The main design consideration is matching the amplifier's speed to the circuit. A high-bandwidth amplifier can amplify high-frequency noise and may require more careful layout than a slow precision op amp. Confirm the package pinout, common-mode range, supply voltage, output swing, and stability requirements against the LT1028 datasheet. This page consolidates the verified LT1028CP product information, application context, design guidance, and source links. It is intended to support preliminary part selection, while the manufacturer datasheet remains the controlling reference for final engineering and production decisions.

見積もりお問い合わせ

LT1030CD

LT1030CD - Quad RS-232 Line Driver 14-SOIC | Texas Instruments

The Texas Instruments LT1030CD is a quadruple low-power EIA/TIA-232-F line driver supplied in a 14-pin SOIC (D) package, with 4 drivers and 0 receivers in the channel count. It operates from a ±5V to ±15V dual supply and draws only 500 µA typical supply current, with the ability to shut down to zero supply current for power-sensitive applications. A line driver is a type of interface IC that converts internal logic-level signals (typically 0/5V TTL or 0/3.3V CMOS) into the higher-voltage levels required by transmission standards such as EIA/TIA-232-F (RS-232). Line drivers sit in the signal chain hierarchy between digital logic and physical connectors, and together with line receivers they form transceivers that enable robust serial communication across cables. The LT1030 is a driver-only device, so designers pair it with an external receiver (such as the SN75C189) to complete an RS-232 link. Key features include ±30V externally-applied voltage tolerance on outputs (with current limiting), 10 mA output drive capability, and outputs that swing within 200 mV of the positive supply and within 1 V of the negative supply to maximize headroom on low-voltage rails. The three-state (open when off) outputs allow several LT1030 devices to be connected in parallel on the same bus for higher drive strength or redundancy. The LT1030C variant is characterized for operation from 0°C to 70°C, in a plastic SOIC-14 (D) package with NiPdAu lead finish. The device also meets or exceeds the EIA/TIA-232-F specification, and can be used as a micropower interface or level translator in addition to its primary RS-232 driver role. Typical applications include portable or battery-powered RS-232 links, micro-power serial ports, level translation between logic families, and parallel-bus drivers that share multiple devices on a single bus. When designing, confirm the receiver side of the link is rated for the same ±25V common-mode range required by the standard.

見積もりお問い合わせ

LT1030CDR

LT1030CDR - Quad RS-232 Line Driver 14-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments LT1030CDR is a quadruple low-power EIA/TIA-232-F line driver supplied in a 14-pin SOIC (D) package, with 4 drivers and 0 receivers in the channel count. It operates from a ±5V to ±15V dual supply and draws only 500 µA typical supply current, with the ability to shut down to zero supply current for power-sensitive applications. A line driver is a type of interface IC that converts internal logic-level signals (typically 0/5V TTL or 0/3.3V CMOS) into the higher-voltage levels required by transmission standards such as EIA/TIA-232-F (RS-232). Line drivers sit in the signal chain hierarchy between digital logic and physical connectors, and together with line receivers they form transceivers that enable robust serial communication across cables. The LT1030 is a driver-only device, so designers pair it with an external receiver (such as the SN75C189) to complete an RS-232 link. Key features include ±30V externally-applied voltage tolerance on outputs (with current limiting), 10 mA output drive capability, and outputs that swing within 200 mV of the positive supply and within 1 V of the negative supply to maximize headroom on low-voltage rails. The three-state (open when off) outputs allow several LT1030 devices to be connected in parallel on the same bus for higher drive strength or redundancy. The LT1030C variant is characterized for operation from 0°C to 70°C, in a plastic SOIC-14 (D) package with NiPdAu lead finish. The device also meets or exceeds the EIA/TIA-232-F specification, and can be used as a micropower interface or level translator in addition to its primary RS-232 driver role. Typical applications include portable or battery-powered RS-232 links, micro-power serial ports, level translation between logic families, and parallel-bus drivers that share multiple devices on a single bus. When designing, confirm the receiver side of the link is rated for the same ±25V common-mode range required by the standard.

見積もりお問い合わせ

LT1030CN

LT1030CN - Quad RS-232 Line Driver, ±15V, 14-PDIP | TI

The Texas Instruments LT1030CN is a quadruple low-power RS-232 line driver supplied in a 14-pin PDIP (N) package, operating from ±5V to ±15V supplies with a typical quiescent supply current of 500 µA and a zero-power shutdown mode. Each of the four drivers delivers a minimum 10 mA output current and is fully protected against externally applied voltages of ±30 V through on-chip current limiting, while presenting a high-impedance 3-state output when shut down. The output swing reaches within 200 mV of the positive supply rail and within 1 V of the negative supply rail, maximizing dynamic range on low-voltage supplies. A line driver is a unidirectional buffer that translates low-voltage logic levels (such as 0/5 V CMOS or 0/3.3 V LVTTL) into the higher-voltage swings required by serial-interface standards. RS-232 is the most widely deployed single-ended asynchronous serial standard, historically using ±12 V signaling to provide noise immunity over cables up to ~15 m. The LT1030CN belongs to the EIA/TIA-232-F line-driver category within the broader interface-IC family, which sits above simple transceivers in the protocol-IC hierarchy because it provides drivers only (no receivers) and is intended to be paired with a separate receiver IC such as the LT1031C. Key features of the LT1030CN include: ±5 V to ±15 V supply range, 500 µA typical supply current, zero supply current in shutdown, ±30 V output overvoltage protection, 10 mA minimum output drive, parallelable outputs for higher drive, and compliance with ANSI EIA/TIA-232-F. The shutdown (SHDN) pin enables power-saving modes in battery-powered terminals, and the 3-state output behavior prevents back-driving when the device is off. The LT1030 architecture uses a charge-pump-free, low-power bipolar driver design that does not require external capacitors; the output stage is built with Darlington-style pull-down and active pull-up devices to achieve the wide ±15 V compliance. Designers should note that the bipolar front-end consumes more quiescent current than CMOS-only alternatives but provides robust ±30 V fault tolerance that is difficult to match with purely CMOS parts. Typical applications for the LT1030CN include: RS-232 driver-only channels where a separate receiver IC is already present, point-of-sale terminals, industrial serial-port modules, battery-powered portable instruments, and legacy peripheral interfaces requiring ±12 V signaling. The 14-PDIP through-hole package simplifies prototyping, rework, and breadboarding versus surface-mount alternatives. When designing with the LT1030CN, place a 0.1 µF bypass capacitor close to each supply pin (V+ and V-) and observe the 10 mA minimum-load requirement on the EIA/TIA-232-F receivers it drives. To shut down the device, pull the SHDN pin high; leaving it floating or grounded keeps the outputs active. Do not exceed ±30 V on any driver output, even though internal current limiting will protect the device.

見積もりお問い合わせ

LT1037CH

LT1037CH - 2.5nV/Hz Precision Low Noise Op Amp | Analog Devices

The Analog Devices (Linear Technology) LT1037CH is a decompensated low-noise, high-speed precision operational amplifier delivering 2.5 nV/sqrt(Hz) wideband input noise, 60 nVp-p 0.1 Hz to 10 Hz noise, and a 60 MHz gain bandwidth product in a hermetically sealed 8-lead TO-5 metal can package. An operational amplifier is an active semiconductor device that amplifies the difference between two input voltages. Precision low-noise op amps such as the LT1037 sit between general-purpose amplifiers and instrumentation-grade devices in the hierarchy: op amp -> voltage-feedback amplifier -> analog signal conditioning IC -> semiconductor. Within that class, the LT1037 family was designed to provide the lowest noise available in a monolithic amplifier, with wideband noise below that of a 400 ohm resistor and a 1/f corner frequency of only 2 Hz. Key differentiating specifications include 10 uV maximum input offset voltage, 0.2 uV/degree C input offset drift, and 130 dB common mode rejection and power supply rejection ratio. Because the LT1037 is a decompensated amplifier, it is only stable for closed-loop gains of 5 or greater, which allows the 60 MHz gain bandwidth product to be traded for very low noise at the input. It is unity-gain stable in a follower configuration only when a gain of 5 or more is used. Internally the LT1037 uses a low-noise bipolar input stage and a precision trim of the input offset voltage with two offset null terminals, pins 1 and 5. The generous supply range supports dual supply operation, and the hermetic TO-5 metal can gives consistent performance in laboratory and instrumentation environments where thermal stability and low drift over time matter more than board area. Typical applications include audio preamplifiers, low-level strain gauge and thermocouple signal conditioning, precision instrumentation amplifiers, seismic and geophone measurement front ends, low-level transducers, and reference buffer circuits for high-resolution data converters. A key design consideration is that the decompensated architecture requires a closed-loop gain of at least 5, so the feedback network values must be chosen carefully; a unity-gain buffer configuration will oscillate unless a gain-setting network is added. Offset null should be used only when trimming is genuinely required, since the internal trim can degrade noise and drift stability. This page consolidates manufacturer specifications, distributor pricing as of 2026-10-30, drop-in replacement options in the same TO-5 footprint, and practical design notes that are not found together in a single manufacturer document.

見積もりお問い合わせ

LT1037CL

LT1037CL - Low-Noise Precision Op Amp | Texas Instruments

The Texas Instruments LT1037CL is a single, low-noise, high-speed precision operational amplifier in an 8-lead TO-99 package. Verified source data identifies a 60 MHz gain-bandwidth product, 2.5 nV/√Hz wideband noise, a 2 Hz 1/f corner, 10 µV offset voltage, 0.2 µV/°C drift, and up to 130 dB common-mode and power-supply rejection. These characteristics position the LT1037CL for precision signal conditioning, low-level sensing, instrumentation, audio, and feedback-control circuits where both noise and DC accuracy matter. An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses high open-loop gain to amplify the difference between two input voltages. The larger product hierarchy is operational amplifier -> voltage-feedback amplifier -> analog signal-conditioning IC -> semiconductor. The LT1037 combines low-voltage noise, high bandwidth, and precision offset performance in one analog building block. It is particularly useful when a design must preserve small signals through a moderate-gain stage rather than merely provide basic amplification. The verified LT1037 family specifications emphasize unusually low wideband noise at 2.5 nV/√Hz, with less noise than a 400 ohm resistor according to the Analog Devices product page. The listed 1/f corner of 2 Hz helps low-frequency noise remain small, while the 60 MHz gain-bandwidth product supports faster closed-loop operation. The decompensated LT1037 is described as stable for closed-loop gains of 5 or greater, an important constraint when selecting feedback networks. Typical uses include low-level sensor interfaces, precision current-feedback and voltage-feedback stages, audio preamplification, laboratory instrumentation, and feedback loops requiring rapid response. The 8-lead TO-99 package supports through-hole insertion and is mechanically distinct from surface-mount equivalents. Designers should preserve the required gain condition and verify the complete pinout against the manufacturer datasheet before assembly. A key design consideration is that low noise alone does not guarantee low total error. Offset voltage, drift, input bias current, common-mode range, supply voltage, and stability must be evaluated together. The verified excerpts do not provide every operating limit or pin-level detail, so final circuit design should use the manufacturer datasheet rather than distributor summaries. This page combines verified product facts, source URLs, cross-reference limitations, and engineering-focused selection guidance. It is intended to help buyers distinguish the LT1037CL from generic precision op amps while avoiding unsupported alternative or compliance claims.

見積もりお問い合わせ

LT1037CP

LT1037CP - 60MHz Low-Noise Precision Op Amp | Analog Devices

The Texas Instruments LT1037CP is a low-noise, high-speed, precision operational amplifier specified for a 60 MHz gain-bandwidth product, 11 V/µs minimum slew rate, and input noise density as low as 2.5 nV/√Hz, supplied in an 8-pin PDIP package. The LT1037 family combines wideband speed with precision performance suitable for instrumentation, audio, and low-level signal-chain designs. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. In the broader hierarchy, this precision op amp belongs to the amplifier IC and linear-semiconductor categories. The LT1037CP is particularly useful when a circuit requires both low input noise and high closed-loop bandwidth rather than only rail-to-rail input/output operation. According to the manufacturer material supplied for the LT1037 family, low-noise performance reaches 2.5 nV/√Hz wideband noise, with a 2 Hz 1/f corner frequency and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. Precision specifications include 10 µV offset voltage, 0.2 µV/°C drift, and 130 dB common-mode and power-supply rejection. The LT1037 is a decompensated amplifier that is stable for closed-loop gains of 5 or greater. The LT1037CP is specified with an 11 V/µs minimum slew rate for the LT1037 and LT1037A, while the family data also describes a typical differential voltage gain of 20 V/µV at 25°C with a 2 kΩ load and ±12 V supplies. Its high speed makes feedback-component selection and PCB layout important: parasitic capacitance, excessive loop gain, and poor grounding can reduce practical stability. Typical applications include low-noise audio preamplification, precision measurement front ends, sensor signal conditioning, laboratory instrumentation, and high-speed analog filtering. The device is most suitable where closed-loop gain can be configured at 5 V/V or higher, because the decompensated architecture is not intended for unity-gain operation. When replacing or fitting this amplifier, verify the exact package, pinout, supply limits, gain stability, offset grade, and input bias-current requirements. The provided data confirms an 8-pin PDIP package and single-amplifier configuration, but complete production specifications and the package drawing should be checked against the manufacturer datasheet before layout release. This product page consolidates the verified LT1037 family specifications, package identity, pricing lead, and design considerations into an engineer-oriented reference while clearly separating confirmed values from parameters that require manufacturer-data confirmation.

見積もりお問い合わせ

LT1039CJ

LT1039CJ - Triple ±30V RS-232 Transceiver | Analog Devices

The Analog Devices LT1039CJ is a triple EIA-232 line transceiver with three drivers, three receivers, shutdown control, and a 18-pin DIP package. It accepts supply voltages up to ±15 V, provides receiver inputs rated to ±30 V, and allows driver outputs to be driven to ±30 V without damage. The receiver inputs use 0.4 V hysteresis and a nominal 30 kΩ input impedance for improved noise immunity. Its three-state outputs become high impedance during shutdown or power-off conditions, allowing shared data lines. An RS-232 transceiver is an interface IC that bridges TTL or CMOS logic and the bipolar voltage levels used by EIA-232 serial links. A driver converts logic signals into RS-232 output levels, while a receiver converts bipolar line signals back into logic-compatible levels. The LT1039CJ belongs to the line-driver and receiver hierarchy within interface ICs, combining three complete RS-232 channels plus power-state control in one device. Key features include operation from single or dual supplies up to ±15 V, overload-protected outputs, three-state shutdown behavior, and receiver inputs that can be driven beyond normal RS-232 levels. The shutdown architecture also includes a BIAS function that allows one receiver to remain active while the rest of the device is shut down. These features are useful when an interface must be disconnected safely from a bus without allowing an inactive driver to disturb the line. The bipolar implementation supports RS-232 voltage levels while maintaining compatibility with TTL and CMOS receiver outputs. Receiver pins are identified as pins 3, 5, and 7, while driver outputs are pins 4, 6, and 8. The exact pin names and supply connections must be verified against the manufacturer datasheet before PCB assembly or replacement. Typical applications include industrial serial ports, test equipment, data acquisition systems, legacy computer peripherals, and instrumentation requiring a three-channel RS-232 interface. The LT1039CJ is most appropriate when the design needs more than one RS-232 channel, controlled shutdown, or protection against externally applied high-voltage line transients. The principal design consideration is ensuring that receiver logic levels and supply sequencing suit the connected controller. RS-232 cable routing should be kept away from noisy power paths, and unused channels should be configured deliberately rather than left floating. The three-state shutdown feature can reduce bus contention, but it does not by itself guarantee compatibility with every RS-232 network. This page combines the verified LT1039CJ datasheet information, package identification, practical interface guidance, and sourced cross-reference limitations. It is intended to help engineers locate the datasheet, understand the transceiver’s electrical behavior, and assess whether a replacement is genuinely pin-compatible.

見積もりお問い合わせ

サブカテゴリ

製品 (39,000+)

LT1013CJG - Dual Precision Op Amp, 300uV Offset, CDIP-8 | Texas Instruments

LT1013CP - Dual Precision Op Amp, 4-44V | Texas Instruments

LT1013DD - Dual Precision 5V-44V Op Amp | Texas Instruments

LT1013DP - Dual Precision Op Amp, 4-44V, 8-PDIP | TI

LT1013IP - Dual Precision Low-Power Op Amp | Texas Instruments

LT1014CJ - Quad Precision Op Amp, 50 uV Offset | Analog Devices

LT1014CN - 4-Channel 5V-44V Precision Op Amp | Texas Instruments

LT1014DN - Quad Precision Op Amp, 14-PDIP | Texas Instruments

LT1014IN - Quad Precision Op Amp, 5V-44V | Texas Instruments

LT1014MJ - 4-Channel 5V-44V Precision Op Amp | Texas Instruments

LT1016CH - 10 ns Precision Comparator | Analog Devices

LT1016CN8 - 10ns UltraFast Precision Comparator | Analog Devices

LT1016CN8#PBF - 10ns UltraFast Precision Comparator | Analog Devices

LT1016CP - 10ns UltraFast Comparator | Analog Devices

LT1017CH - Micropower Dual Comparator | Analog Devices

LT1022MH - 26V/us Precision JFET Op Amp | Analog Devices

LT1028CP - 75MHz Ultralow-Noise Precision Op Amp | Analog Devices

LT1030CD - Quad RS-232 Line Driver 14-SOIC | Texas Instruments

LT1030CDR - Quad RS-232 Line Driver 14-SOIC | Texas Instruments (Tape & Reel)

LT1030CN - Quad RS-232 Line Driver, ±15V, 14-PDIP | TI

LT1037CH - 2.5nV/Hz Precision Low Noise Op Amp | Analog Devices

LT1037CL - Low-Noise Precision Op Amp | Texas Instruments

LT1037CP - 60MHz Low-Noise Precision Op Amp | Analog Devices

LT1039CJ - Triple ±30V RS-232 Transceiver | Analog Devices