マイクロコントローラ

製品 (18727)

ATSAM4SD32CA-ANR - 120MHz Cortex-M4 MCU 2MB Flash | Microchip
ATSAM4SD32CA-ANR

ATSAM4SD32CA-ANR - 120MHz Cortex-M4 MCU 2MB Flash | Microchip

The Microchip Technology ATSAM4SD32CA-ANR is a 32-bit ARM Cortex-M4 microcontroller in the SAM4S family, running at up to 120 MHz with 2 MB of embedded Flash and 160 KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package. It integrates a Floating Point Unit (FPU), a high-speed Multi-port SRAM, and a flexible bus matrix, providing deterministic real-time performance for industrial and consumer embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The Cortex-M4 core is a 32-bit processor widely adopted across industrial, IoT, and motor-control applications because it combines Thumb-2 instruction efficiency with DSP extensions and an optional single-precision FPU. The SAM4S series, built around this core, sits within Microchip's portfolio of mainstream ARM Cortex-M microcontrollers and is typically chosen when deterministic interrupt latency, large on-chip Flash (>= 1 MB), and a rich peripheral set (USB FS, CAN, Ethernet MAC, HS SDIO/MMC, multiple UART/SPI/TWI, ADC, PWM) are required in one device. Key features of the ATSAM4SD32CA-ANR include a maximum core clock of 120 MHz, 2 MB (2M x 8) Flash program memory, 160 KB SRAM, a full-speed USB 2.0 device/host controller, a 10/100 Ethernet MAC, a CAN controller, a high-speed SDIO/MMC interface, up to 47 user I/O lines, and multiple 16-bit timers plus a 12-bit ADC. The integrated FPU accelerates single-precision floating-point math, while the on-chip voltage regulator and Power-on Reset reduce external BOM. A 64-pin LQFP package offers an easy-to-assemble, hand-solderable footprint suitable for prototypes and mid-volume production. Architecturally, the SAM4S uses a multi-layer AHB bus matrix that allows simultaneous accesses to Flash, SRAM, and peripherals without contention. The Flash controller incorporates a 128-bit-wide prefetch buffer and a write buffer, allowing the Cortex-M4 to execute code from Flash with zero-wait-state performance at up to 120 MHz under specified conditions. Peripherals are connected via separate peripheral bridges so that DMA activity does not stall CPU code fetches. Typical applications include industrial automation controllers (PLC modules, sensor hubs, smart gateways), human-machine interface (HMI) panels, USB peripherals (data loggers, mass-storage devices, CDC + HID bridges), CAN node interfaces in vehicles or factory equipment, and motor-control boards that benefit from the FPU for field-oriented control (FOC) loops. The integrated Ethernet MAC also makes the part a fit for low-cost networked embedded nodes. When designing with the ATSAM4SD32CA-ANR, pay attention to decoupling: place a 100 nF X7R ceramic plus a 4.7 uF bulk capacitor close to each VDDCORE and VDDBU supply pin. The 64-pin LQFP has a thermal pad-free design, so the die dissipates heat mainly through the package leads; however, at industrial temperatures (-40 C to +85 C) and 120 MHz operation, modest copper pour is sufficient. This page synthesizes distributor stock, drop-in pin-compatible alternatives, and practical PCB/thermal design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
ATSAM4SD32CA-AUR - 120MHz Cortex-M4 MCU 2MB Flash | Microchip
ATSAM4SD32CA-AUR

ATSAM4SD32CA-AUR - 120MHz Cortex-M4 MCU 2MB Flash | Microchip

The Microchip ATSAM4SD32CA-AUR is a high-performance 32-bit ARM Cortex-M4 microcontroller based on the SAM4S core, delivering 120 MHz CPU clock speed with 2 MB of embedded Flash and 160 KB of SRAM in a 100-pin LQFP (14x14 mm) package supplied on Tape and Reel. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one die. The Cortex-M4 core specifically adds a single-precision FPU, DSP extensions, and a Memory Protection Unit (MPU), positioning it in the 32-bit embedded hierarchy above Cortex-M0/M0+ and below Cortex-M7. The SAM4S family sits in Microchip's mid-range MCU lineup, between the lower-pin-count SAM D20/D21 and the higher-performance SAME70/SAMS70 lines. Microcontrollers in this class are typically used as the central processing element in industrial control, IoT edge nodes, and human-machine interface (HMI) products. Key features of the ATSAM4SD32CA-AUR include 2 MB Flash with 16 KB user signature page, 160 KB SRAM organized across Tightly Coupled Memory (TCM) and system bus regions, a Multi-layer Bus Matrix with separate peripheral and DMA channels, and up to 24 DMA channels. Communication peripherals include high-speed USB 2.0 Full-Speed with on-chip transceiver, up to three USARTs, two UARTs, two TWI (I2C) controllers, two SPI controllers, and an I2S interface. Analog peripherals include a 12-bit ADC with up to 16 channels and a 12-bit DAC. The device operates from 1.62 V to 3.6 V. Typical applications for the ATSAM4SD32CA-AUR include industrial automation controllers, building automation gateways, smart energy meters, point-of-sale terminals, and connected HMI panels. The high Flash density and USB Full-Speed make it particularly attractive for products that require firmware over-the-air (FOTA) staging or local diagnostic logging, while the 12-bit ADC supports sensor aggregation. Design consideration: the on-chip voltage regulator requires a stable 3.3 V supply; add 100 nF + 4.7 µF decoupling near VDDCORE and 100 nF on every VDDIO pin. The 100-pin LQFP footprint is shared with most ATSAM4S/4SD family members, simplifying board reuse across variants.

見積もり お問い合わせ
ATSAM4SD32CA-CFU - 120MHz Cortex-M4 MCU, 2MB Flash | Microchip
ATSAM4SD32CA-CFU

ATSAM4SD32CA-CFU - 120MHz Cortex-M4 MCU, 2MB Flash | Microchip

The Microchip (formerly Atmel) ATSAM4SD32CA-CFU is a high-performance 32-bit ARM Cortex-M4 microcontroller from the SAM4S family, featuring 2MB of Flash and 160KB of SRAM, operating at up to 120 MHz core clock, and housed in a 100-pin VFBGA package (7x7 mm). It integrates a high-speed USB 2.0 Full-Speed interface, dual CAN controllers, up to 5 UART/USART, 3 TWI (I2C-compatible), an external bus interface, and a 12-bit ADC, making it a single-chip solution for connected embedded systems. A Cortex-M4 microcontroller is a 32-bit processor core based on the ARMv7-M architecture that combines deterministic interrupt response with DSP extensions (single-cycle MAC) and an optional single-precision FPU. Within the broader taxonomy, this places the SAM4S family under the MCU > microcontroller > embedded processor > semiconductor hierarchy. The Cortex-M4 lineage was introduced by ARM in 2010 to target mixed signal control and DSP workloads, and Microchip's SAM4S implementation layers a rich peripheral set and low-power modes around the core for industrial, consumer, and IoT applications. Key features include a 1.25 DMIPS/MHz core with hardware multiplier and single-cycle MAC, dual-bank Flash with security bit and 128-bit unique ID, multi-layer AHB bus matrix, and the SAM4S Peripheral Event System for low-latency hardware-triggered tasks. The device supports 1.62V to 3.6V operation with an integrated voltage regulator, and offers Sleep, Wait, and Backup modes with fast wake-up for power-constrained designs. The 12-bit ADC reaches up to 1 Msps and pairs well with the chip's hardware-triggered timers. Typical applications include industrial automation and PLC I/O, USB peripherals, CAN-based automotive body and automotive clusters, smart energy metering (smart meters), consumer audio and human-machine interface panels, and home automation gateways. The wide memory configuration (2MB Flash + 160KB SRAM) also fits well into embedded Linux-adjacent workloads such as gateway firmware, secure boot, and OTA upgrade handlers. When designing with this part, ensure PCB layout routes the VFBGA 0.65 mm pitch on inner layers with appropriate microvia stackups and provides a solid GND plane under the exposed die pad for thermal dissipation. The integrated voltage regulator requires a 10 uF bulk capacitor on VDDOUT, and decoupling must follow Microchip's SAM4S hardware design guide.

見積もり お問い合わせ
ATSAM4SD32CA-CFUR - 120MHz Cortex-M4 2MB Flash MCU | Microchip
ATSAM4SD32CA-CFUR

ATSAM4SD32CA-CFUR - 120MHz Cortex-M4 2MB Flash MCU | Microchip

The Microchip (formerly Atmel) ATSAM4SD32CA-CFUR is a high-performance 32-bit ARM Cortex-M4 microcontroller running at up to 120 MHz, with 2 MB of Flash and 160 KB of SRAM, packaged in a 100-ball VFBGA (7x7 mm). It belongs to the SAM4S family and integrates a multi-layer bus matrix, a multi-channel DMA controller, and distributed memory architecture to sustain high data-rate peripheral I/O. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (timers, communication interfaces, ADCs). Cortex-M4 cores add single-cycle DSP and a single-precision FPU, allowing cost-effective signal-processing workloads. The SAM4S series sits in Microchip's mid-performance MCU tier above Cortex-M0+ parts and below Cortex-M7 high-end families, targeting industrial control, smart energy, and connected sensor applications. Key features of the ATSAM4SD32CA-CFUR include 2 MB on-chip Flash (organized as 2M x 8), 160 KB SRAM, a 16-bit External Bus Interface (EBI) for SRAM/NOR/NAND expansion, a high-speed USB 2.0 Full-Speed (12 Mbps) Device with on-chip PHY, and a 10/100 Ethernet MAC with MII/RMII interface. The part operates from 1.2 V core / 3.3 V I/O rails, and integrates advanced touch sensing (QTouch), a 12-bit ADC, and a hardware cryptographic engine for AES and secure boot. Designed for industrial-grade reliability, the device supports an ambient temperature range of -40 C to +85 C and is RoHS-compliant. The VFBGA-100 7x7 mm package is footprint-compatible with other SAM4S VFBGA variants, enabling PCB reuse when scaling flash or peripheral mix. Pin-to-pin and software compatibility with the SAM3S Cortex-M3 family provides a smooth upgrade path for performance gains without firmware redesign. Typical applications include industrial automation controllers, smart grid and metering endpoints, point-of-sale terminals, HVAC controls, and USB/Ethernet-connected sensor hubs. Its DSP instructions and FPU also suit audio front-end processing and motor-control loops using PWM plus ADC triggering. When designing with this part, allocate careful PCB layout for the VFBGA-100 footprint: 0.5 mm ball pitch requires microvia HDI stack-up and X-ray or rework-station assembly. Decouple every VDD18/VDD33 pin pair with 100 nF ceramic plus bulk 4.7 uF, and provide a low-impedance ground plane under the BGA for thermal dissipation (theta_JA around 25 C/W on a 4-layer JEDEC test board). This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design guidance for the ATSAM4SD32CA-CFUR, sourced from Microchip's SAM4S datasheet and live distributor inventories.

見積もり お問い合わせ
ATSAM4SD32CA-CU - 120MHz Cortex-M4 MCU 2MB Flash 100-TFBGA | Microchip
ATSAM4SD32CA-CU

ATSAM4SD32CA-CU - 120MHz Cortex-M4 MCU 2MB Flash 100-TFBGA | Microchip

The Microchip ATSAM4SD32CA-CU is a 32-bit ARM Cortex-M4 microcontroller running up to 120 MHz with 2 MB of embedded Flash and 160 KB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package with industrial temperature grade. It belongs to the SAM4S family and integrates a 2 KB instruction cache, Memory Protection Unit (MPU), single-precision hardware Floating Point Unit (FPU), DSP instruction extensions, and a Thumb-2 instruction set that preserves code density while sustaining high code-throughput performance. A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a rich set of on-chip peripherals (timers, communication controllers, ADCs, etc.) into one package. The Cortex-M4 lineage places the SAM4S as a deterministic real-time MCU that targets signal-processing and connectivity-rich embedded systems. Within the broader taxonomy, the SAM4S sits in the hierarchy: Cortex-M4 -> ARM Cortex-M family -> 32-bit MCU -> microcontroller -> embedded IC -> semiconductor device. Key features include 2 MB of dual-bank Flash supporting read-while-write operation, 160 KB SRAM with flexible bus matrix, multi-channel DMA, full-speed USB 2.0 device/host/OTG, two CAN controllers, three USARTs, two UARTs, two TWIs, two SPIs, one 10-bit ADC (up to 16 channels and 1 MSps), an SD/MMC interface, a 16-bit timer/counter block, and a real-time clock with calendar. The device is pin-to-pin compatible with SAM3N, SAM3S, and SAM7S legacy 64/100-pin versions, allowing an easy drop-in upgrade path. Operating voltage spans 1.62 V to 3.6 V, suiting single-cell Li-ion or 3.3 V regulated rails. Typical applications include industrial control boards, smart energy metering, motor drive front-ends, building automation gateways, USB peripherals, and consumer devices requiring DSP-class DSP-ready signal processing. The combination of Cortex-M4 DSP extensions and the integrated FPU enables audio decoding, sensor-fusion DSP routines, and modest DSP workloads without a separate DSP chip. A key design consideration is bus-matrix bandwidth at high peripheral activity - place time-critical ISRs in SRAM and avoid blocking DMA paths when running high-throughput USB or Ethernet stacks. To preserve regulator headroom, design with a 3.3 V LDO that has at least 100 mA of burst capacity for ADC + USB peaks. This page synthesizes the verified distributor pricing, drop-in alternatives, and practical design notes that are not assembled in any single manufacturer datasheet.

見積もり お問い合わせ
ATSAM4SD32CA-CUR - 120MHz Cortex-M4 MCU 2MB Flash | Microchip
ATSAM4SD32CA-CUR

ATSAM4SD32CA-CUR - 120MHz Cortex-M4 MCU 2MB Flash | Microchip

The Microchip Technology ATSAM4SD32CA-CUR is a 32-bit ARM Cortex-M4 microcontroller in the SAM4S family, operating at up to 120 MHz with 2 MB of embedded Flash and 160 KB of SRAM, housed in a 100-ball 9x9 mm TFBGA package supplied on Tape & Reel. It integrates a single-precision Floating Point Unit, a high-speed 16-bit ADC, USB 2.0 Full-Speed with on-chip PHY, multiple UART/SPI/TWI/I2S interfaces, and an External Bus Interface for memory expansion, making it a complete system-on-chip for connected embedded designs. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and I/O on a single silicon die. ARM Cortex-M4 cores implement the Thumb-2 instruction set with hardware single-cycle multiply and optional single-precision FPU, fitting between Cortex-M0+ (lowest power) and Cortex-M7 (highest performance) in the Cortex-M hierarchy. Within power-management IC taxonomy, MCUs belong to the broader category of embedded processors / microcontrollers, sitting alongside DSPs, FPGAs, and application processors. Key features of the ATSAM4SD32CA-CUR include its 120 MHz maximum CPU clock, single-cycle DSP MAC instructions, 2 MB Flash with security and secure boot, 160 KB SRAM (plus 2 KB backup SRAM), and 1.2 V internal core voltage supplied by an on-chip voltage regulator from a single 1.62-3.6 V external supply. The device provides up to 79 GPIO, up to 25 communication channels (USART, SPI, TWI), and a 10/100 Ethernet MAC with MII/RMII interface. The architecture uses a multi-layer AHB bus matrix with separate bridges for code and data, eliminating contention between CPU and DMA. A peripheral DMA controller (PDC) with up to 24 channels enables zero-CPU-overhead data movement between peripherals and memory. The on-chip Flash is mapped at 0x00400000 and supports in-application programming via the SAM-BA bootloader. Typical applications include industrial control (PLC, motor drives, HMI), consumer audio (USB speakers, headphones, audio docks), smart energy metering, building automation gateways, and connected IoT edge nodes requiring USB connectivity. The combination of 2 MB code space and high-speed ADC also suits data-acquisition loggers and portable instrumentation. Design consideration: the 100-ball TFBGA requires a 4-layer PCB minimum with matched-length impedance control on USB/Ethernet differential pairs; place decoupling capacitors (100 nF + 4.7 µF) within 2 mm of every VDD pin to meet IEC 61967 EMI margins. This page synthesizes XAIPART distributor pricing, drop-in same-package alternatives from the SAM4S and SAM4S16A families, and design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
ATSAM4SD32CB-AN - 2MB Flash Cortex-M4 MCU 100-LQFP | Microchip
ATSAM4SD32CB-AN

ATSAM4SD32CB-AN - 2MB Flash Cortex-M4 MCU 100-LQFP | Microchip

The Microchip Technology ATSAM4SD32CB-AN is a 32-bit ARM Cortex-M4 RISC microcontroller featuring 2MB of embedded Flash, 160KB of SRAM, and a maximum CPU clock of 120 MHz, housed in a 100-pin LQFP (14x14 mm) package. It integrates a full-speed USB Device port with embedded transceiver, a 10/100 Ethernet MAC (GMAC), and a rich set of peripherals including up to five USARTs, five UARTs, two TWIs, three SPIs, an 8-channel 10-bit ADC, a 16-bit PWM, and a 16-bit timer/counter block. An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core designed by Arm that includes a single-precision IEEE 754 floating-point unit (FPU), a Memory Protection Unit (MPU), and DSP extensions. Within Microchip's broader hierarchy it sits under the SAM family -> SAM4S sub-family -> ARM Cortex-M4 series, occupying a position aimed at high-performance industrial and consumer embedded designs where deterministic control and connectivity coexist. Key features of the ATSAM4SD32CB-AN include dual-bank Flash for in-application reprogramming, a unique 128-bit serial number, a true random number generator (TRNG), and Cryptography accelerators (AES, TDES). The part is rated for the extended industrial temperature range up to +105C, and uses a 1.2V core supply. It is pin-compatible with the rest of the SAM4S family (SAM4S2/4/8/16/32) in the same 100-LQFP outline, allowing design scalability. Architecturally, the SAM4SD32 pairs the Cortex-M4 core with a multi-layer bus matrix that gives the CPU, DMAC, and peripherals simultaneous access to Flash and SRAM, eliminating contention. The dual-bank Flash and the peripheral event system enable deterministic interrupt latency and zero-latency interrupt responses, which are critical for motor control, power conversion, and real-time communications. Typical applications include industrial control and HMI, USB peripherals and HID devices, smart energy metering, point-of-sale terminals, barcode scanners, and machine-to-machine (M2M) gateways. The combination of USB, Ethernet, and Cortex-M4 DSP capability also makes it attractive for audio processing nodes and low-cost PLCs. When designing with this device, ensure that the 1.2V core rail is decoupled close to the VDD pins and that the external reset circuit meets the datasheet's minimum reset pulse width. The flash dual-bank layout also requires that bootloader and application boundaries are planned early. This page synthesizes distributor pricing, pin-to-pin compatible SAM4S family alternatives, and practical design notes not consolidated on the manufacturer product page.

見積もり お問い合わせ
ATSAM4SD32CB-CFN - 120MHz Cortex-M4 MCU 2MB Flash | Microchip
ATSAM4SD32CB-CFN

ATSAM4SD32CB-CFN - 120MHz Cortex-M4 MCU 2MB Flash | Microchip

The Microchip Technology ATSAM4SD32CB-CFN is a 32-bit ARM Cortex-M4 microcontroller from the SAM4S family, delivering up to 120 MHz core performance with 2 MB of embedded Flash and 160 KB of SRAM, packaged in a 100-ball 7x7 mm VFBGA. The device integrates a single-precision Floating Point Unit (FPU), a Memory Protection Unit (MPU), and up to 4 Kbytes of cache, providing a balanced combination of computational density and deterministic real-time response. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a rich set of peripherals (timers, communication controllers, ADCs, GPIOs). The ARM Cortex-M4 is a 32-bit RISC core with DSP extensions and an optional FPU, purpose-built for embedded deterministic control in cost- and power-sensitive applications. The SAM4S family extends this core with Microchip-specific peripherals (HS USB, EMAC, CAN, SSC) and aims at industrial, consumer, and connectivity-enabled embedded designs. Key features of the ATSAM4SD32CB-CFN include 2 MB dual-bank Flash, 160 KB SRAM, full-speed USB Device port with on-chip transceiver, up to 16 peripheral DMA channels, 12-bit ADC, two 16-bit timers, and up to five USART, three SPI, and two TWI (I2C-compatible) interfaces. An integrated 32-bit real-time timer and a 128-bit unique device ID are also provided. The Cortex-M4 core with FPU executes Thumb-2 instructions and DSP blocks at up to 1.25 DMIPS/MHz, allowing digital signal processing workloads to share the same MCU that performs supervisory control. The architecture uses a multi-layer bus matrix connecting the Cortex-M4 core, Flash controller, SRAM, and peripheral bridges, minimising contention under concurrent DMA transfers. The 100-ball VFBGA (7x7 mm, 0.65 mm pitch) supports compact layouts for space-constrained designs and provides ample GPIO for parallel buses and high-pin-count peripherals. The 1.2 V internal core is regulated from a single 1.62 V to 3.6 V external supply, simplifying power-tree design. Typical applications include industrial control and Human-Machine Interface (HMI) panels, smart energy metering, USB peripherals (data loggers, HID devices), point-of-sale terminals, building automation gateways, and consumer audio/connectivity hubs. The combination of Cortex-M4 DSP, USB, and large Flash suits firmware-upgradable field devices with on-device signal conditioning. When migrating existing SAM4S designs, verify revision status: the manufacturer datasheet recommends Revision B silicon for new prototypes and production. Footprint-compatible lower-density SAM4S variants (SAM4SD16, SAM4SA16, SAM4S16, SAM4S8, SAM4S4) share the same 100-ball VFBGA pad map and pinout, simplifying capacity scaling without PCB rework. This page synthesises distributor pricing, drop-in compatible SAM4S variants, and practical design notes that supplement the manufacturer datasheet with sourcing and replacement context.

見積もり お問い合わせ
ATSAM4SD32CB-CN - SAM4S ARM Cortex-M4 MCU 120MHz 2MB Flash | Microchip
ATSAM4SD32CB-CN

ATSAM4SD32CB-CN - SAM4S ARM Cortex-M4 MCU 120MHz 2MB Flash | Microchip

The Microchip Technology ATSAM4SD32CB-CN is an ARM Cortex-M4 SAM4S microcontroller integrating 2MB of Flash and 160KB of SRAM, operating at up to 120 MHz core clock, and housed in a 100-ball TFBGA (9x9 mm) package. The device is the production revision B of the SAM4SD32 family and is rated for the extended industrial temperature range (-40C to +85C). A 32-bit MCU (microcontroller) is a single-chip computer that integrates a processor core, program memory (Flash), data memory (SRAM), and a rich set of peripherals on one die. Microcontrollers sit within the broader taxonomy of microprocessors -> embedded processors -> microcontrollers -> ARM Cortex-M microcontrollers. The Cortex-M4 core additionally provides a single-precision FPU and DSP extensions, making the SAM4S suitable for signal-processing tasks in addition to conventional control. Key features of the ATSAM4SD32CB-CN include a full-speed USB Device port with embedded transceiver, up to two HS USB hosts/device/OTG capable ports in the family, a 16-bit static memory controller for external NAND Flash / NOR / SDRAM, dual 16-bit ADC and a 12-bit DAC, multiple UART/USART, TWI (I2C), SPI, SSC, and an on-chip temperature sensor. The dual-bank Flash with cache memory accelerates code execution from on-chip storage, while the integrated voltage regulator supports single-supply operation from a 1.62V to 3.6V source (with separate I/O and core domains). Architecturally the SAM4S combines an M-class core with a Multi-layer Bus Matrix and dedicated peripheral DMA channels that enable parallel data movement between peripherals, SRAM, and Flash without CPU intervention. Revision B (the -CB- suffix) fixes silicon errata and is Microchip's recommended variant for new designs over revision A. Typical applications include industrial control and HMI panels, USB-connected peripherals such as data loggers and POS terminals, smart energy metering, building automation gateways, and motor-control front-ends. The dual ADC channels and DSP extensions make it well suited to closed-loop feedback control where firmware implements PID or field-oriented motor control algorithms. When designing with this device, pay close attention to the decoupling network: place a 100 nF X7R 0402 next to every VDD/VDDIO ball pair, add a bulk 4.7 uF tantalum or ceramic at the regulator output, and keep the 32.768 kHz crystal traces short with a guarded ground plane to avoid RTC drift.

見積もり お問い合わせ
ATSAMA5D21A-CU - ARM Cortex-A5 MPU 500MHz 196-TFBGA | Microchip
ATSAMA5D21A-CU

ATSAMA5D21A-CU - ARM Cortex-A5 MPU 500MHz 196-TFBGA | Microchip

The Microchip Technology ATSAMA5D21A-CU is a high-performance, low-power ARM Cortex-A5 embedded microprocessor (MPU) running up to 500 MHz, packaged in a 196-ball TFBGA (CSBGA) at 0.75 mm pitch. According to the Microchip SAMA5D2 product page, the device integrates 128 KB of internal SRAM and supports multiple external memories including DDR2, DDR3L, LPDDR2, LPDDR3, QSPI Flash, and e.MMC Flash, providing flexible boot and storage options for embedded Linux designs. An ARM Cortex-A5 microprocessor is a 32-bit RISC application processor core built on the ARMv7-A architecture that executes operating systems such as Linux via a memory management unit (MMU). It sits hierarchically above microcontrollers in compute capability, offering application-processor-class performance with on-chip FPU, NEON media engine, and rich peripheral integration for HMI, edge connectivity, and industrial gateways. Key features include the 500 MHz Cortex-A5 core with ARM NEON and FPU, hardware cryptography acceleration (AES, SHA, TRNG), dual CAN-FD controllers, dual Ethernet GMAC with 1588 PTP, USB 2.0 high-speed host and device, and a 12-bit ADC. The SAMA5D21A-CU variant is rated for industrial temperature range (-40C to +85C), distinguishing it from the commercial-temperature -CN suffix. It supports 24-bit display output via LCD controller and camera input through the CSI interface, making it well-suited for HMI panels. Architecturally, the SAMA5D2 family uses a single-core Cortex-A5 implementation with 32 KB instruction and 32 KB data caches plus a 128 KB system SRAM that can be used as a tightly coupled memory for deterministic interrupt latency. The advanced interrupt controller (AIC) and low-power modes (Idle, Ultra-Low-power, Backup, and Shutdown) with RTC retention allow deep-sleep operation under 5 µA. Typical applications include industrial IoT gateways, HMI panels with capacitive touch, building automation controllers, smart energy concentrators, and Linux-based edge appliances. The wide memory interface and dual CAN-FD make it equally appropriate for automotive telematics, fleet management, and point-of-sale terminals. When designing with this device, ensure proper DDR signal routing with matched lengths and reference the Microchip ATSAMA5D2 Xplained Ultra board design files for validated power, decoupling, and QSPI boot layouts. The 0.75 mm pitch TFBGA requires PCB fabrication with laser-drilled microvias or 0.1 mm trace/space rules.

見積もり お問い合わせ
ATSAMA5D21A-CUR - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip
ATSAMA5D21A-CUR

ATSAMA5D21A-CUR - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip

The Microchip Technology ATSAMA5D21A-CUR is a high-performance, ultra-low-power Arm Cortex-A5 microprocessor (MPU) running up to 500 MHz, integrating 128 KB SRAM, a floating-point unit (FPU), and external memory controllers for DDR2/DDR3L/LPDDR2/LPDDR3 and QSPI/e.MMC flash in a 196-ball TFBGA package with industrial temperature range. An Arm Cortex-A5 MPU is a microprocessor unit based on the ARMv7-A architecture that integrates a CPU core, memory controllers, and rich peripherals into a single package. In the embedded hierarchy it sits above microcontrollers (MCUs) and is used when applications need a full operating system such as Linux, high-throughput peripherals like Gigabit Ethernet, or large DDR memories. The SAMA5D2 family specifically targets low-power connected IoT gateways, HMI panels, and industrial control. Key features include the 500 MHz Cortex-A5 core with 32 KB each of L1 instruction and data cache plus 128 KB L2 SRAM, single-precision FPU, hardware video decoder/encoder accelerators, a 12-bit ADC, and a comprehensive peripheral set including Gigabit Ethernet, two CAN-FD controllers, USB host/device, and multiple UART/SPI/I2C interfaces. The 196-ball TFBGA package is a fine-pitch surface-mount BGA with thermal pad suitable for industrial PCB designs. Architecturally, the device uses ARM's Cortex-A5 core paired with a multi-layer AHB/APB bus matrix and dedicated DMA engines. It supports secure boot via on-chip OTP and hardware crypto accelerators (AES, SHA, TRNG), enabling tamper-resistant firmware deployment. The integration of analog and digital peripherals reduces external component count in industrial designs. Typical applications include industrial IoT gateways, building automation controllers, human-machine interface (HMI) panels, smart energy concentrators, and connected medical devices. The wide industrial temperature range makes it suitable for outdoor or factory-floor deployments. When designing with this MPU, pay close attention to power-rail sequencing and decoupling. Place at least eight 100 nF decoupling capacitors near the BGA balls and provide a 4-layer PCB with continuous ground plane for DDR signal integrity. Validate boot configuration against the SAMA5D2 hardware design checklist. This page synthesizes distributor stock levels, TFBGA-196 same-family alternatives, and practical PCB design notes beyond the manufacturer datasheet to accelerate your engineering decisions.

見積もり お問い合わせ
ATSAMA5D21B-CU - ARM Cortex-A5 500MHz MPU, 196-TFBGA | Microchip
ATSAMA5D21B-CU

ATSAMA5D21B-CU - ARM Cortex-A5 500MHz MPU, 196-TFBGA | Microchip

The Microchip ATSAMA5D21B-CU is a high-performance, low-power ARM Cortex-A5 32-bit microprocessor (MPU) running up to 500 MHz, integrated in a 196-TFBGA (11x11) package with 0.8 mm ball pitch. The single-core Cortex-A5 includes a NEON and FPU co-processor and integrates powerful peripherals for connected, secure industrial and IoT embedded systems. An MPU (Microprocessor Unit) is a processor-class device that requires external memory and is intended to run a full operating system such as Linux, in contrast to a microcontroller (MCU) which integrates Flash/RAM and runs bare-metal or RTOS. Within the Microchip portfolio, the SAMA5D2 series occupies the low-power, Cortex-A5 MPU tier above Cortex-M microcontrollers and below higher-end Cortex-A7/A53 application processors. The ATSAMA5D21B-CU supports DDR2/DDR3L/LPDDR2/LPDDR3 external SDRAM, plus QSPI and e.MMC flash interfaces, allowing flexible memory architectures for cost-sensitive designs. Key differentiating features include 5 µA backup-mode current for battery-backed applications, an embedded audio subsystem with Class-D amplifier support, hardware crypto accelerators (AES, SHA, TRNG), secure boot, and tamper detection. The 196-TFBGA package reduces PCB routing complexity versus larger BGA options while still exposing the full peripheral set including dual Ethernet GMAC, dual CAN-FD, USB host/device, and TFT LCD controller. The architecture is built on a low-power process with extensive clock gating, targeting extended battery life in always-connected edge nodes. The integrated Cortex-A5 core with NEON/FPU accelerates multimedia workloads such as image processing, audio codecs, and HMI rendering, while the deeply integrated peripherals eliminate the need for external components. Typical applications include industrial HMI panels, smart energy gateways, building automation controllers, IoT edge nodes, low-power Linux gateways, and secure connected devices. The wide memory and peripheral support makes the ATSAMA5D21B-CU a versatile platform for industrial-grade Linux deployments. When designing with this MPU, ensure the 0.8 mm-pitch BGA is manufactured with via-in-pad or dog-bone fan-out, and that the DDR routing meets JEDEC signal-integrity requirements for the selected SDRAM type. Plan power-rail sequencing per the SAMA5D2 hardware design guide. This page synthesizes distributor pricing, drop-in SAMA5D2 alternatives, and practical hardware design notes not collected in a single location by the manufacturer datasheet.

見積もり お問い合わせ
ATSAMA5D21B-CUR - 500MHz Cortex-A5 MPU | Microchip
ATSAMA5D21B-CUR

ATSAMA5D21B-CUR - 500MHz Cortex-A5 MPU | Microchip

The Microchip Technology ATSAMA5D21B-CUR is a 32-bit ARM Cortex-A5 embedded microprocessor running at up to 500 MHz, integrating 128 KB of internal SRAM and housed in a 196-ball TFBGA (11x11 mm) package with 0.8 mm ball pitch. It is a single-core member of the SAMA5D2 series, designed for low-power industrial and IoT applications requiring high integration and a simple power management scheme. An embedded microprocessor unit (MPU) is a general-purpose processor core intended to run a full operating system such as Linux, as distinct from a microcontroller (MCU) that typically runs bare-metal or RTOS firmware. Within the product hierarchy, the SAMA5D2 is an application-class MPU built on the ARM Cortex-A5 architecture, which itself belongs to the ARMv7-A family of 32-bit application processors. The Cortex-A5 delivers roughly 1.57 DMIPS/MHz with an optional NEON SIMD unit, positioning it between the low-end Cortex-M class and the higher-performance Cortex-A7/A9 cores. Key features of the ATSAMA5D21B-CUR include a 500 MHz maximum core clock, 128 KB internal SRAM, a 16-bit DDR2/DDR3L/LPDDR2/LPDDR3 external memory controller, and support for QSPI and e.MMC flash. The device integrates an embedded audio subsystem with a fractional PLL, a 12-bit ADC, and a comprehensive security block including secure boot, TRNG, and tamper detection. Its ultra-low-power architecture reaches 5 uA in backup mode, making it suitable for battery-backed designs. The SAMA5D2 architecture uses a 32-bit ARMv7-A core with 32 KB instruction and 32 KB data L1 caches, a 128 KB L2 cache, and a multi-layer AHB bus matrix. The 0.8 mm ball pitch TFBGA package reduces PCB design complexity compared with finer-pitch alternatives, allowing lower-cost fabrication and simpler routing for 4- to 6-layer boards. Typical applications include industrial HMI panels, IoT gateways, point-of-sale terminals, building automation controllers, and portable medical devices. The combination of 500 MHz performance, integrated audio, and 5 uA backup current fits designs that must wake quickly from sleep while maintaining long battery life. When designing with this MPU, pay close attention to the DDR memory routing and the power sequencing of the 1.2 V core, 1.8 V/3.3 V I/O, and 1.8 V DDR rails. The SAMA5D2 reference design and the SAMA5D2 Xplained Ultra evaluation kit provide validated schematics and layout guidance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and integration decisions.

見積もり お問い合わせ
ATSAMA5D21C-CU - 500MHz Cortex-A5 MPU | Microchip 196-TFBGA
ATSAMA5D21C-CU

ATSAMA5D21C-CU - 500MHz Cortex-A5 MPU | Microchip 196-TFBGA

The Microchip Technology ATSAMA5D21C-CU is an ARM Cortex-A5 based embedded microprocessor unit (MPU) running at up to 500 MHz, housed in a 196-ball TFBGA (11x11 mm, 0.8 mm pitch) package. It integrates 32 KB L1 instruction cache, 32 KB L1 data cache, and 128 KB L2 cache, and is the production-grade member of the SAMA5D2 family targeting industrial HMI, IoT gateways, and connected peripherals. An MPU (microprocessor unit) is a class of integrated circuit that integrates a CPU core, memory controllers, and a rich set of peripherals into a single System-in-Package (SiP). Unlike microcontrollers (MCUs), MPUs typically lack on-chip non-volatile memory and instead boot from external QSPI, eMMC, or SD flash, while running Linux or other high-level operating systems. The SAMA5D2 family sits within Microchip's portfolio of low-power Cortex-A5 application processors, between the lower-cost SAM9 series (ARM926) and the higher-end SAMA7 (Cortex-A7). Key features include a 32-bit single-core ARM Cortex-A5 with NEON and FPU, hardware cryptography accelerators (AES, SHA, TRNG), advanced connectivity (Gigabit Ethernet with 1588 PTP, USB HS, CAN-FD, two SD/SDIO/MMC), 12-bit ADC, and a Class D audio amplifier. The SAMA5D2 integrates a sophisticated power management IC that enables backup mode consuming only 5 uA, dramatically extending battery life in always-aware edge devices. The architecture combines Cortex-A5 efficiency with a hardware crypto subsystem supporting secure boot, secure storage, and tamper detection, making it suitable for payment terminals, access control, and IoT security applications. The SiP integrates up to 1 Gbit DDR2 or 2 Gbit LPDDR2 SDRAM directly in the package, simplifying PCB design and reducing BOM cost. Typical applications include industrial HMI panels, smart energy gateways, barcode scanners, IoT edge nodes, point-of-sale terminals, building automation controllers, and connected medical devices. Its low-power backup mode and high peripheral integration make it ideal for battery-backed industrial sensors and remote IoT nodes. When designing with this MPU, plan for an external boot memory (QSPI NOR or eMMC), provide a 3.3V main supply and 1.35V or 1.55V core supply, and ensure the DDR2/LPDDR2 routing follows the JEDEC layout guidelines. Designers should also evaluate the SAMA5D2 software ecosystem, which includes Linux mainline support, Yocto BSP, and AT91Bootstrap, accelerating time to production. This page synthesizes distributor pricing, drop-in alternatives within the SAMA5D2 family, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate the ATSAMA5D21C-CU for industrial IoT and HMI designs.

見積もり お問い合わせ
ATSAMA5D21C-CUR - ARM Cortex-A5 MPU 500MHz 196-TFBGA | Microchip
ATSAMA5D21C-CUR

ATSAMA5D21C-CUR - ARM Cortex-A5 MPU 500MHz 196-TFBGA | Microchip

The Microchip ATSAMA5D21C-CUR is a high-performance, low-power ARM Cortex-A5 32-bit microprocessor (MPU) running up to 500 MHz, housed in a 196-ball TFBGA (11x11 mm, 0.8 mm pitch) package. It belongs to the SAMA5D2 series and integrates 160 KB ROM, an embedded audio subsystem, advanced security features, and support for DDR2/DDR3L/LPDDR2/LPDDR3 external memories plus QSPI and e.MMC Flash interfaces. An MPU (Microprocessor Unit) is an integrated circuit that contains a full central processing unit, memory management, and a rich set of on-chip peripherals. Within the broader semiconductor taxonomy, an MPU is a sub-category of microprocessor -> processor -> integrated circuit -> semiconductor. Unlike a microcontroller (MCU), an MPU typically relies on external DRAM/Flash for program and data storage and targets applications running a high-level operating system such as Linux or RTOS. Key features of the ATSAMA5D21C-CUR include: ARM Cortex-A5 core with NEON and floating-point extensions, hardware cryptographic accelerators (AES, SHA, TRNG), 5 µA backup mode current for battery-backed designs, 10/100 Mbps Ethernet MAC, USB 2.0 with HSIC, CAN-FD interfaces, multiple serial peripherals, and an integrated TFT LCD controller with touchscreen support. The 0.8 mm pitch BGA package reduces PCB routing complexity. Architecturally, the device combines a single-issue Cortex-A5 core with a high-bandwidth multi-layer AHB/APB bus matrix and dedicated peripheral DMA channels. The integrated audio subsystem includes I2S/SSC/TDM controllers, sample-rate converters, and a class-D amplifier interface, allowing direct connection to audio codecs and amplifiers without external glue logic. Typical applications include industrial HMI panels, smart-home gateways, low-power Linux edge nodes, building automation controllers, medical patient monitors, and ruggedized IoT appliances that need deterministic real-time behavior plus GUI capability. The 5 µA backup current also makes it attractive for battery-backed telemetry units. When designing with this MPU, ensure schematic-level decoupling of all VDD rails per the SAMA5D2 hardware design guide and provide a stable external 12–24 MHz crystal for the PLL. The industrial-grade temperature range allows operation in -40 °C to +85 °C environments. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the SAMA5D2 family, application companion parts, and practical design notes not aggregated on a single manufacturer page.

見積もり お問い合わせ
ATSAMA5D225C-D1M-CU - 500MHz Cortex-A5 MPU w/ 128Mb DDR2 SiP | Microchip
ATSAMA5D225C-D1M-CU

ATSAMA5D225C-D1M-CU - 500MHz Cortex-A5 MPU w/ 128Mb DDR2 SiP | Microchip

The Microchip ATSAMA5D225C-D1M-CU is a high-performance, low-power Arm Cortex-A5 microprocessor (MPU) running up to 500 MHz, integrating 128 Mbit of DDR2 SDRAM in a System-in-Package (SiP) configuration. Housed in a 196-ball TFBGA (11x11 mm, 0.8 mm pitch) package, the device combines the application processor and DRAM into a single footprint, reducing PCB complexity and BOM cost for embedded designs. An MPU (Microprocessor Unit) is a processor class above microcontrollers (MCUs): it integrates a CPU core complex, memory management unit (MMU), and rich peripherals but relies on external (or in this case, packaged) DRAM and storage for program/data. Within the power-management/embedded hierarchy the Cortex-A5 MPU sits between Cortex-M MCUs (deterministic, lower power) and Cortex-A application processors (higher performance, MMU-capable, Linux-capable). The SAMA5D2 family targets industrial HMI, IoT gateways, and low-power connected devices. Key features include Arm TrustZone for Cortex-A5, secure boot, tamper detection, secure data storage, a peripheral touch controller (PTC), an embedded audio subsystem (I2S/Class-D), and hardware crypto accelerators (AES, SHA, TRNG). Connectivity peripherals cover Ethernet GMAC, CAN-FD, USB HSIC and USB HS host/device, FLEXCOM (USART/SPI/TWI), QSPI, and e.MMC/SD interfaces. The integrated 128 Mbit DDR2 eliminates the PCB-level memory design challenge. Architecturally the device uses a single-issue, in-order Cortex-A5 core with NEON media engine, achieving ~1.58 DMIPS/MHz while keeping typical active power in the low hundreds of mW range. Multi-mode power management (ULP, backup, deep-sleep) allows battery-powered designs to idle at single-digit mW. Display support up to WXGA (1366x768) via 24-bit RGB LCD controller suits industrial panel integration. Typical applications include industrial HMI panels, smart-home and IoT gateways, building automation controllers, medical patient monitors, point-of-sale terminals, and ruggedized portable instrumentation where low BOM cost and a compact SiP footprint outweigh the need for application-grade DRAM capacity. Design consideration: because the DDR2 is internal, route the SiP signal breakout on inner layers to maintain signal integrity; follow the 0.8 mm BGA escape pattern in the datasheet and provide adequate decoupling (1 uF + 100 nF per supply rail cluster). This page synthesizes Microchip and distributor specifications, drop-in alternatives within the SAMA5D2 family, and practical SiP layout notes not consolidated in a single vendor datasheet.

見積もり お問い合わせ
ATSAMA5D225C-D1M-CUR - ARM Cortex-A5 MPU 500MHz 128Mbit DDR2 | Microchip
ATSAMA5D225C-D1M-CUR

ATSAMA5D225C-D1M-CUR - ARM Cortex-A5 MPU 500MHz 128Mbit DDR2 | Microchip

The Microchip Technology ATSAMA5D225C-D1M-CUR is an ARM Cortex-A5 based embedded microprocessor (MPU) running up to 500 MHz, integrating 128 Mbit of DDR2 SDRAM in a 196-ball TFBGA (11x11 mm, 0.8 mm pitch) System-in-Package (SiP). Designed for the SAMA5D2 family, this low-power MPU combines an Arm Cortex-A5 core with rich connectivity and advanced security features including Arm TrustZone, tamper detection, secure boot, and secure data storage. The 32-bit single-core architecture targets industrial-grade applications where deterministic performance and low system cost are equally critical. A microprocessor (MPU) is a fully integrated CPU subsystem - core, caches, memory controller, peripherals, and external memory bus - packaged as a single IC. Unlike microcontrollers (MCUs) that embed Flash and run bare-metal or RTOS code, MPUs require external boot media (QSPI NOR, NAND, eMMC, SD card) and typically run a full operating system (Linux, Yocto, Buildroot, Android). The SAMA5D2 series occupies the upper end of industrial-grade MPUs, balancing high-level OS capability with deep-sleep current suitable for always-on battery-backed systems. Key features include the 500 MHz Cortex-A5 with NEON media engine, integrated 128 Mbit DDR2 (16-bit data bus), peripheral touch controller, embedded audio subsystem with sample-rate converters, 0.8 mm ball pitch to simplify PCB layout, hardware cryptography (AES, SHA, TRNG), and a simple power-management scheme that supports retention and ultra-low-power modes. The device exposes multiple connectivity options including 10/100 Ethernet MAC, USB HS host/device, CAN-FD, multiple SPI/I2C/UART instances, and LCD TFT controller. The SiP integration eliminates the DDR2 routing challenge between MPU and discrete DRAM, reducing 4-layer PCB complexity and improving signal integrity for industrial-grade EMC compliance. The 196-ball TFBGA footprint, 0.8 mm pitch, and 11x11 mm body make the part suitable for compact HMI, gateway, and edge-compute designs. Typical applications include industrial HMI panels, IoT gateways with secure boot, smart-home controllers with touch UI, building-automation bridges, point-of-sale terminals, low-power premium consumer devices, and secure connected embedded peripherals with Yocto or Buildroot Linux. When designing with the ATSAMA5D225C-D1M-CUR, plan a 4-layer PCB with continuous ground stitching under the BGA, follow the Microchip SAMA5D2 hardware design checklist for DDR2 termination, and ensure boot configuration straps (BMS, JTAG select) are correctly pulled for the selected boot media. This page synthesizes distributor stock and pricing, drop-in same-package SAMA5D2 family alternatives, and practical design notes not aggregated in any single manufacturer datasheet or distributor catalog page.

見積もり お問い合わせ
ATSAMA5D22A-CN - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip
ATSAMA5D22A-CN

ATSAMA5D22A-CN - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip

The Microchip ATSAMA5D22A-CN is a high-performance 32-bit ARM Cortex-A5 microprocessor unit (MPU) running up to 500 MHz, housed in a 196-ball TFBGA package with external memory support. The part integrates 128 KB of SRAM, an LCD controller, a 10/100 Mbps Ethernet MAC, USB 2.0 with HSIC, CAN-FD controllers, hardware AES and secure boot features, plus extended-temperature (105 °C) industrial qualification. It targets connected embedded applications requiring rich graphics and robust security. An ARM Cortex-A5 microprocessor is a 32-bit RISC application processor designed for industrial and IoT endpoints. MPU products of this class sit above microcontrollers in capability, running full operating systems (typically Linux) while providing external DDR memory, multiple high-speed peripherals, and advanced graphics. The SAMA5D2 family specifically emphasizes low power, hardware cryptography (AES, secure boot, OTP), and human-machine interface (HMI) features such as LCD, touch, and image-sensor interfaces. Positioned in the broader ARM ecosystem, Cortex-A5 MPs offer higher compute density than Cortex-M MCUs while remaining more power-efficient than Cortex-A7/A53 application processors. Key features include ARM Cortex-A5 core at up to 500 MHz with NEON and FPU options, 16-bit DDR3/DDR3L/LPDDR2/LPDDR3 external memory interface, 2D graphics accelerator (GC320), integrated LCD controller up to WXGA resolution, dual CAN-FD, three HS USB 2.0 ports, 10/100 Ethernet MAC with 1588 support, hardware AES/SHA/TRNG secure boot, image-sensor interface, and a wide operating temperature range of -40 °C to +105 °C. The 196-ball TFBGA (10x10 mm) package supports industrial-grade reflow profiles. Typical applications span industrial IoT gateways, building automation controllers, smart-home hubs, medical patient-monitoring terminals, point-of-sale systems, and ruggedized HMI panels. The on-chip AES and secure boot make it suitable for connected devices requiring tamper-resistant firmware, while the LCD controller and 2D accelerator enable graphical UIs without an external GPU. When designing with the ATSAMA5D22A-CN, ensure the DDR3/LPDDR2 routing follows the SAMA5D2 hardware design guide for impedance-controlled length-matched traces, and provide the minimum 1.0 V core and 1.2/1.8 V DDR rails with proper decoupling. The device boots from QSPI or SD-card and supports seamless Linux mainline distribution. This page synthesizes distributor pricing, drop-in alternatives from the same SAMA5D2 family, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
ATSAMA5D22A-CNR - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip
ATSAMA5D22A-CNR

ATSAMA5D22A-CNR - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip

The Microchip ATSAMA5D22A-CNR is a high-performance ARM Cortex-A5 32-bit microprocessor (MPU) from the SAMA5D2 family, operating at up to 500 MHz and packaged in a 196-ball TFBGA (11x11 mm) with 0.75 mm pitch. The -CNR suffix denotes the industrial temperature grade, tape-and-reel packaging, and the BGA GREEN / MRLA configuration with hardware cryptography (AES, Secure Boot, TRNG) and HSIC + CAN-FD peripherals enabled. The SAMA5D2 family targets secure, low-power connected embedded designs with an Arm TrustZone-aware architecture and a rich peripheral set. A microprocessor (MPU) is an integrated circuit containing a full CPU core with external memory bus, designed to run an operating system such as Linux or RTOS. Microprocessors sit at the top of the embedded compute hierarchy above microcontrollers (MCU); while an MCU integrates Flash and RAM on-die, an MPU requires external DDR memory and boots from QSPI/SD/eMMC. The SAMA5D2 series is built around the Cortex-A5 application-class core, with NEON absent and a single-precision FPU, balanced for deterministic real-time workloads at modest power. Key features include a 32-bit DDR2/DDR3/DDR3L/LPDDR1/LPDDR2/LPDDR3 memory controller with 16-bit data bus, hardware AES/SHA/TRNG crypto accelerators, dual Ethernet (10/100 + 10/100/1000) MAC, three USB 2.0 ports plus HSIC, three CAN-FD controllers, two SD/SDIO/MMC interfaces, TFT LCD controller up to 1024x768, 12-bit ADC, and a Class D audio amplifier interface. Peripherals are multiplexed through a flexible PIO controller to 196 balls. The SAMA5D22 variant (versus 500 MHz) also integrates 128 KB SRAM and 160 KB ROM alongside the cache subsystem. Typical applications include industrial HMI panels, building automation gateways, smart-energy concentrators, medical patient-monitoring terminals, point-of-sale terminals, and connected IoT edge nodes running Linux. The Cortex-A5 core delivers adequate headroom for Qt-based UIs, lightweight web servers, and TLS-secured MQTT while the crypto block accelerates TLS handshakes and secure-boot verification. Operating at 1.2 V core / 1.8 V DDR / 3.3 V I/O, the device balances performance against a power budget well suited to fanless enclosures. When designing with the ATSAMA5D22A-CNR, allocate a 4-layer PCB with continuous ground pour beneath the 11x11 mm TFBGA, route DDR traces with length-matched impedance (40 ohm SE / 80 ohm diff), and place at least one 10 uF + 1 uF + 100 nF decoupling group per power rail. Use Microchip's Linux4SAM BSP and the SAMA5D2 Xplained board as a validated starting point. This page combines distributor pricing, drop-in alternative MPNs, and design notes curated from Microchip application notes and reference designs - information not found in any single datasheet or distributor listing.

見積もり お問い合わせ
ATSAMA5D22A-CU - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip
ATSAMA5D22A-CU

ATSAMA5D22A-CU - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip

The Microchip Technology ATSAMA5D22A-CU is a 32-bit ARM Cortex-A5 embedded microprocessor (MPU) from the SAMA5D2 series, operating at up to 500 MHz in a 196-ball TFBGA (11x11 mm, 0.8 mm pitch) package. It integrates an ARM NEON SIMD engine for multimedia acceleration, 128 KB of on-chip SRAM, and a peripheral touch controller for HMI designs. A microprocessor (MPU) is an integrated circuit that contains a full CPU core plus caches, memory management, and a rich peripheral set, intended to run a high-level operating system such as Linux. MPUs sit above microcontrollers (MCUs) in the embedded hierarchy: they require external DDR memory, deliver much higher compute throughput, and are typically deployed where an OS, complex GUI, networking stack, or multimedia processing is needed. The Cortex-A5 is ARM's smallest, lowest-power applications-class core, designed for cost-sensitive, power-constrained embedded products. Key features of the ATSAMA5D22A-CU include support for LPDDR1/LPDDR2/LPDDR3, DDR2, DDR3, DDR3L, and QSPI memories, hardware graphics acceleration, an embedded audio subsystem, and a 10/100 Mbps Ethernet MAC. The integrated peripheral touch controller (PTC) supports moisture-tolerant capacitive touch sensing directly, reducing BOM cost. A simple power management scheme and 5 uA backup-mode current enable long battery life across industrial and IoT endpoints. The device architecture combines the Cortex-A5 core with NEON SIMD, floating-point hardware, and a multi-layer bus matrix feeding the advanced interrupt controller, DMA, and peripherals. Hardware graphics acceleration offloads 2D composition, while the LCD controller supports displays up to WXGA. Cryptographic accelerators (AES, SHA, TRNG) are integrated for secure-boot and TLS workloads. The 196-ball TFBGA package uses a 0.8 mm ball pitch to simplify PCB routing on low-cost 4-layer stack-ups. Typical applications include industrial HMI panels with capacitive touch, building automation gateways, smart energy meters, point-of-sale terminals, medical patient-monitoring displays, and connected IoT edge nodes running Linux. The wide memory-controller compatibility also suits brownfield designs migrating from older ARM9 or Cortex-A8 platforms. When designing with this MPU, allocate at least a 4-layer PCB with a continuous ground plane beneath the BGA, follow the SAMA5D2 hardware design checklist for DDR3L length-matching, and provide a clean 3.3 V I/O plus 1.2/1.8/3.3 V rail scheme per the reference schematic. Boot configuration, OTP fuse, and secure-boot flow should be finalized early, as they constrain later firmware decisions. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the SAMA5D2 family, and practical hardware design notes that go beyond the manufacturer datasheet to help engineers shorten their bring-up cycle.

見積もり お問い合わせ
ATSAMA5D22A-CUR - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip
ATSAMA5D22A-CUR

ATSAMA5D22A-CUR - 500MHz Cortex-A5 MPU, 196-TFBGA | Microchip

The Microchip Technology ATSAMA5D22A-CUR is a high-performance, ultra-low-power 32-bit ARM Cortex-A5 microprocessor unit (MPU) from the SAMA5D2 series, running up to 500 MHz with single-core processing in a 196-ball TFBGA (11x11 mm) package on tape and reel. It integrates a NEON MPE co-processor for multimedia acceleration and a dedicated graphics accelerator, supports DDR2/DDR3L/LPDDR2/LPDDR3 external memories plus QSPI and e.MMC Flash, and is qualified for industrial temperatures up to 105 C. An MPU (microprocessor unit) is a system-on-chip category that integrates a CPU core, memory controller, peripherals, and optional accelerators onto a single die. Within the broader taxonomy, the ATSAMA5D22A-CUR sits under ARM Cortex-A application processors -> microprocessor unit -> integrated circuit. MPUs typically run Linux or other high-level operating systems, distinguishing them from microcontrollers (MCUs) which run bare-metal or RTOS firmware. The Cortex-A5 core implements the ARMv7-A architecture with TrustZone security extensions and a Memory Management Unit (MMU) for full virtual-memory operating systems such as Linux. Key features include a Peripheral Touch Controller (PTC), embedded audio subsystem with I2S and Class D amplifier support, dual EMAC Ethernet, two HSIC USB ports, three HS/FS USB ports, two CAN-FD controllers, hardware AES-OTF (on-the-fly) encryption engine, 0.8 mm ball-pitch BGA package that simplifies PCB layout, and a simple power-management scheme. The SAMA5D2 architecture achieves ultra-low standby power of approximately 5 uA in backup mode with retention, enabling battery-backed designs that must survive months on a single cell. Typical applications include HMI (human-machine interface) panels, IoT edge gateways, smart-home controllers, building-automation bridges, industrial-control HMIs, and connected medical devices. The on-chip graphics accelerator plus LCD controller supports up to WXGA (1280x768) displays without external graphics silicon, while the AES engine and secure-boot ROM simplify connected-product security. When designing with this MPN, ensure the PCB uses 0.8 mm-pitch micro-via BGA fan-out routing and that the DDR interface is length-matched within the JEDEC JESD79 DDR specification. The 11x11 mm TFBGA has 196 balls on 0.8 mm pitch, so blind or buried vias are typically required for escape routing on a 4-layer board. Linux BSP support is available through the mainline kernel and Microchip's at91bootstrap bootloader, with mainline Device Tree bindings for all on-chip peripherals.

見積もり お問い合わせ
ATSAMA5D22B-CN - Cortex-A5 500MHz MPU 196-TFBGA | Microchip
ATSAMA5D22B-CN

ATSAMA5D22B-CN - Cortex-A5 500MHz MPU 196-TFBGA | Microchip

The Microchip ATSAMA5D22B-CN is a high-integration ARM Cortex-A5 microprocessor from the SAMA5D2 series, operating at up to 500 MHz with a single 32-bit core, housed in a 196-ball TFBGA (11x11 mm, 0.8 mm pitch) package. The device integrates 128 KB of internal SRAM and targets cost-sensitive, low-power embedded applications that require rich multimedia and connectivity peripherals. The ATSAMA5D22B variant is the latest silicon revision B of the SAMA5D22 family, offering improved security and peripheral enhancements over revision A. An ARM Cortex-A5 microprocessor is a 32-bit application-class processor core designed for embedded Linux, RTOS, and bare-metal workloads. It sits in the application-processor tier of the microcontroller hierarchy (MCU -> Cortex-M -> Cortex-A5 -> Cortex-A7/A9/A53) and pairs with external DDR memory via an integrated controller, unlike Cortex-M parts that rely on embedded flash. The SAMA5D2 family extends Cortex-A5 with hardware cryptography (AES/SHA), a peripherals touch controller (PTC), an embedded audio subsystem, and a graphics LCD controller, eliminating the need for several companion ICs on the bill of materials. Key features include an external memory bus supporting LPDDR1/LPDDR2/LPDDR3/DDR2/DDR3/DDR3L, dual QSPI interfaces for high-speed flash, hardware AES-256 and SHA engines, a 720p LCD controller with overlay, an embedded audio PLL and 24-bit stereo codec-class I2S block, USB 2.0 with HSIC, and a 10/100 Ethernet MAC. Peripherals include CAN-FD, up to three SD/SDIO/MMC controllers, 12-bit ADC, and up to seven UARTS. Power consumption drops to approximately 5 uA in backup mode with retention SRAM. The architecture combines an ARMv7-A Cortex-A5 core with NEON single-precision SIMD and a 32 KB instruction / 32 KB data L1 cache. The memory controller supports up to 1 GB of addressable DDR-class RAM, and the system runs Linux, Android, or any ARMv7 RTOS out of the box. On-chip security includes secure boot, OTP, tamper pins, and OTFAES for DDR bulk encryption at run-time. Typical applications include HMI panels and industrial gateways, smart-home control panels with capacitive touch, IoT edge nodes with secure boot, smart energy meters with LCD, and rugged portable medical or test instruments. Designers frequently pair the part with a PMIC such as the MIC2800 or an LDO bank supplying 1.2 V core, 1.8 V DDR, and 3.3 V I/O rails. When designing the PCB, allocate at least four PCB layers for the DDR routing with controlled-impedance traces and matched length on the clock pair. Keep the 32.768 kHz crystal traces short and surrounded by a guard ground. The 0.8 mm ball pitch BGA demands precise land pattern, via-in-pad with resin fill, and a PCB fabricator capable of laser-drilled microvias. This page synthesizes distributor stock, drop-in SAMA5D2 alternatives, and design guidance specific to the ATSAMA5D22B-CN revision B silicon, complementing the manufacturer datasheet with parametric context that engineer and sourcing teams can use to qualify second-source parts.

見積もり お問い合わせ
ATSAMA5D22B-CNR - 500MHz Cortex-A5 MPU 196-TFBGA | Microchip
ATSAMA5D22B-CNR

ATSAMA5D22B-CNR - 500MHz Cortex-A5 MPU 196-TFBGA | Microchip

The Microchip Technology ATSAMA5D22B-CNR is a 32-bit ARM Cortex-A5 microprocessor from the SAMA5D2 series, operating at up to 500 MHz in a 196-ball TFBGA (11x11x1.2 mm) package with a 0.8 mm ball pitch. It integrates a single Cortex-A5 core with the ARMv7-A architecture, including ARM TrustZone, a NEON Media Processing Engine for multimedia, and a floating-point unit. The device operates from a 1.2 V core supply and targets industrial and IoT embedded applications. A microprocessor (MPU) is a system-on-chip integrating a CPU core, memory controllers, peripherals, and interconnect fabrics onto a single die. The SAMA5D2 family sits within Microchip's MPU portfolio between the lower-end SAMA5D4 and higher-performance SAMA7G series. It is designed to balance deterministic real-time performance, low power consumption, and rich peripheral integration for human-machine interface (HMI), connectivity, and graphical IoT edge nodes. Key features include 32 KB L1 data cache, 32 KB L1 instruction cache, and a 128 KB L2 cache that is configurable as internal SRAM. The chip embeds a Peripheral Touch Controller (PTC), an audio subsystem supporting I2S/TDM, hardware cryptography accelerators (AES, SHA, TRNG), and a graphics LCD controller up to WXGA (1280x800). The 0.8 mm ball pitch simplifies PCB routing and reduces layer count compared to finer-pitch BGA designs. The architecture combines the Cortex-A5 application processor subsystem with an extensive peripheral set including dual Ethernet GMAC, dual CAN-FD, USB 2.0 with HSIC, up to three SD/SDIO/MMC controllers, and a 12-bit ADC. The SAMA5D2 implements TrustZone for secure boot and secure key storage, plus secure boot ROM and tamper detection pins for industrial-grade protection. Typical applications include industrial HMI panels, IoT gateways, smart-home control units, point-of-sale terminals, building automation controllers, and low-cost connected appliances. It also fits low-power vision devices, barcode scanners, and printer control boards where Linux or RTOS support and Cortex-A class performance are required. When designing with this device, allocate at least a 4-layer PCB with controlled-impedance routing for the DDR2/LPDDR/LPDDR2/LPDDR3 interface. Decouple the 1.2 V core rail with bulk ceramic capacitors placed close to the BGA balls, and follow Microchip's SAMA5D2 hardware design checklist for power sequencing, boot mode configuration, and JTAG debug access. This page synthesizes distributor pricing, drop-in pin-compatible same-package variants, and practical design considerations not consolidated in any single source. All specifications trace to the manufacturer datasheet and authorized distributors.

見積もり お問い合わせ
ATSAMA5D22B-CU - 500MHz ARM Cortex-A5 MPU, 196-TFBGA | Microchip
ATSAMA5D22B-CU

ATSAMA5D22B-CU - 500MHz ARM Cortex-A5 MPU, 196-TFBGA | Microchip

The Microchip ATSAMA5D22B-CU is a 32-bit ARM Cortex-A5 embedded microprocessor (MPU) running up to 500 MHz on a single core, housed in a 196-ball TFBGA (11x11) package with 0.8 mm pitch. It belongs to the SAMA5D2 family, integrates ARM Neon media processing and ARM TrustZone security, and ships with 128 Kbytes of L2 cache configurable as SRAM and 32 Kbytes each of L1 instruction and data caches. What is an embedded MPU? An MPU (Microprocessor Unit) integrates a CPU core, memory controller, and a wide range of system peripherals on a single chip, replacing the CPU plus Northbridge/Southbridge of older x86 designs. The SAMA5D2 lineage sits in the Linux-capable MPU tier above microcontroller units (MCUs), competing with NXP i.MX6ULL and TI AM335x in human-machine interface, IoT gateways, and industrial control boards where the workload demands a full operating system rather than bare-metal firmware. The Cortex-A5 core implements the ARMv7-A architecture, which supports virtual memory, symmetric multiprocessing, and the full ARM exception model required by Linux distributions. Key features of the ATSAMA5D22B-CU include an MMU for full Linux/Android support, ETM/ETB debug tracing, a 16-bit DDR memory controller for LPDDR1/2/3 and DDR2/3/3L, dual QSPI and e.MMC flash interfaces, hardware AES/SHA accelerators, and an integrated LCD controller supporting up to XGA at 60 fps. Peripherals include USB 2.0 high-speed host and device, two HSIC ports, two 10/100 Ethernet MACs with 1588 PTP hardware timestamps, two CAN-FD controllers, and a 12-bit 1 MSPS ADC. Typical applications cover industrial IoT gateways, smart energy concentrators, building automation panels, medical point-of-care terminals, and human-machine interface panels where the MPU runs Linux and renders LVDS/RGB LCDs. The wide memory compatibility (LPDDR1/2/3 and DDR2/3/3L) gives designers latitude in BOM selection between low-cost DDR3L and high-bandwidth LPDDR3. When laying out the PCB, allocate a 4-layer minimum stackup with the inner layers as ground and a 3.3 V power plane, follow the package escape guidelines for 0.8 mm pitch BGA, and provide a dedicated 25 MHz crystal with a load capacitor matched to the oscillator stage. Use only RoHS-compliant SAC305 solder and a JEDEC J-STD-020 profile with a peak reflow below 250 C to avoid internal package delamination.

見積もり お問い合わせ