マイクロコントローラ

製品 (18735)

ATSAMD10D13A-MUT - ARM Cortex-M0+ MCU, 48MHz, 8KB Flash | Microchip
ATSAMD10D13A-MUT

ATSAMD10D13A-MUT - ARM Cortex-M0+ MCU, 48MHz, 8KB Flash | Microchip

The Microchip Technology ATSAMD10D13A-MUT is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D10D family, integrating 8KB of Flash and 4KB of SRAM in a 24-pin QFN (4x4 mm) package. It runs at a maximum clock frequency of 48MHz and reaches 2.46 CoreMark/MHz, delivering a balanced combination of processing throughput and ultra-low power consumption for cost-sensitive embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, ADCs, and GPIO. The ATSAMD10D13A sits inside the Cortex-M0+ ecosystem, the smallest and most energy-efficient member of the ARM Cortex-M family, optimized for deterministic real-time control and low active/standby power. Within Microchip's portfolio it belongs to the broader hierarchy of 32-bit MCU -> ARM Cortex-M0+ MCU -> SAM D microcontroller -> SAM D10D sub-family -> power management and industrial control IC family. Key features of the ATSAMD10D13A-MUT include a 32-bit Cortex-M0+ core with single-cycle I/O access, 8KB Flash with read-while-write support, 4KB SRAM, an integrated 12-bit ADC, multiple SERCOM (serial communication) interfaces configurable as UART/SPI/I2C, a 16-bit timer/counter, and a full-speed USB 2.0 device interface on selected package pins. The device operates from a 1.62V to 3.63V supply and offers multiple low-power sleep modes (IDLE, STANDBY, BACKUP) that drop current consumption to a few microamps, enabling battery-powered and energy-harvesting designs. Technically, the ATSAMD10D13A uses Microchip's proprietary event system and Peripheral Touch Controller (PTC) supporting capacitive touch sensing via hardware-accelerated acquisition. The single-cycle I/O port provides deterministic GPIO access for time-critical control loops, while the SERCOM peripherals are highly flexible and remappable. Built-in hardware CRC, true random number generator, and secure boot features strengthen firmware integrity for connected applications. Typical applications include home automation nodes, smart lighting, IoT sensor endpoints, consumer HMI, low-cost industrial metering, capacitive touch keypads, and USB HID peripherals. The combination of small QFN-24 footprint and 8KB Flash makes it ideal for size-constrained, low-cost 32-bit designs migrating from 8-bit PIC or AVR architectures. When designing with this device, ensure decoupling capacitors are placed within 3mm of the VDD pins, and reserve PA24/PA25 for SWD if in-circuit debugging is required.

見積もり お問い合わせ
ATSAMD10D13A-SSUT - ARM Cortex-M0+ MCU, 48MHz, 8KB Flash | Microchip
ATSAMD10D13A-SSUT

ATSAMD10D13A-SSUT - ARM Cortex-M0+ MCU, 48MHz, 8KB Flash | Microchip

The Microchip Technology ATSAMD10D13A-SSUT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D10D family, operating at up to 48 MHz and delivering 2.46 CoreMark/MHz. It integrates 8 KB of Flash and 4 KB of SRAM, all housed in a 20-pin SOIC (300-mil) package. The device operates from 1.62 V to 3.63 V and supports both industrial (–40 °C to +85 °C) temperature grades. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for low-power embedded designs; it sits at the entry level of the Cortex-M family (M0/M0+ → M3 → M4 → M7), which itself is part of the broader 32-bit embedded processor hierarchy. Microcontrollers therefore belong to the embedded computing → processor → microcontroller → Cortex-M0+ taxonomy. Key features of the ATSAMD10D13A-SSUT include a Serial Communication Manager (SERCOM) block configurable as I²C/SPI/UART, a 12-bit 350 ksps ADC, 10-bit DAC, multiple timers (TC/TCC), a Real-Time Clock, and full-speed USB 2.0 device support. The integrated Event System allows deterministic peripheral-to-peripheral signaling without CPU intervention, and the Peripheral Touch Controller (PTC) supports capacitive touch buttons, sliders, and proximity sensing. Architecturally, the SAM D10D uses a single-cycle hardware multiplier, single-cycle 32-bit MAC, and Microchip's proprietary low-power SleepWalking technology. Power consumption is below 70 µA/MHz in active mode and drops to sub-µA levels in deep-sleep retention, enabling multi-year battery life in sensor products. Typical applications include home-automation nodes, smart-metering endpoints, consumer wearables, low-cost sensor hubs, and industrial HMI sub-modules. The 20-pin SOIC footprint simplifies hand-soldering and rework for prototyping while remaining compatible with high-volume SMT lines. When designing with this part, pay attention to the SERCOM pin-mux table—the same physical pin can serve multiple functions, so firmware planning and PCB routing must be done together. Decoupling VDDIN with a 100 nF ceramic capacitor within 5 mm of the pin is mandatory for ADC and USB accuracy. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes that go beyond what is found in the standalone manufacturer datasheet, helping engineers select, source, and qualify the part faster.

見積もり お問い合わせ
ATSAMD10D14A-MNT - 48MHz Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD10D14A-MNT

ATSAMD10D14A-MNT - 48MHz Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip Technology ATSAMD10D14A-MNT is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D10 family, delivering up to 48 MHz core performance with 16 KB of Flash and 4 KB of SRAM in a compact 24-pin 4x4 mm QFN package. Operating from 1.6 V to 3.6 V across the industrial temperature range (-40C to +105C), this device achieves 2.46 CoreMark/MHz efficiency, making it one of the most power-conscious Cortex-M0+ parts in its class. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by ARM Holdings as the smallest, lowest-power member of the Cortex-M family. It uses the Thumb-2 instruction set subset, includes a single-cycle 32x32 hardware multiplier, and targets cost-sensitive embedded applications that benefit from modern 32-bit performance, deterministic interrupt handling via the Nested Vectored Interrupt Controller (NVIC), and broad ecosystem support. Within the broader system hierarchy it belongs to microcontrollers (MCU), then to embedded processors, and ultimately to the integrated circuit (IC) taxonomy; in power terms it occupies the ultra-low-power tier favored by battery-operated IoT endpoints. Key features include the Cortex-M0+ core with single-cycle I/O access, an integrated high-speed 48 MHz internal RC oscillator (with on-the-fly re-calibration), a 32 kHz low-power oscillator option for RTC use, multiple SERCOM serial interfaces, a 12-bit ADC, 10-bit DAC, and configurable PWM timers. The device supports up to 22 GPIO pins, hardware CRC, a frequency meter, and a touch-friendly peripheral mix that suits capacitive sensing front-ends. Microchip's SAM D10 family is also notable for integrating a peripheral touch controller (PTC) for button/slider/proximity surfaces. Architecturally the part combines a von-Neumann bus with tightly-coupled Flash and SRAM, zero-wait-state execution from Flash up to 48 MHz, and a sophisticated SleepWalking peripheral system that wakes only the peripherals needed for an event. The brown-out detector (BOD), power-on reset (POR), and window watchdog timer (WDT) together provide a robust embedded safety net, while the 6-channel event system and DMA-free interrupt-driven SERCOM mapping reduce CPU load in typical sensor-fusion designs. Typical applications include home-automation sensor nodes, low-end consumer wearables, smart metering endpoints, industrial control sub-modules, and human-machine interface (HMI) accessories such as capacitive touch buttons. The combination of small QFN-24 footprint and low active current also makes it attractive as a co-processor or housekeeping MCU in larger systems. When designing with this part, allocate the SERCOM and TC peripherals carefully against GPIO count, and remember the QFN-24 (4x4 mm) requires careful PCB land pattern work and an exposed thermal pad that should be soldered for best thermal and electrical performance. This page consolidates distributor pricing, drop-in alternatives in the same 24-QFN footprint, and design notes compiled from the manufacturer datasheet and typical applications, going beyond what any single source provides.

見積もり お問い合わせ
ATSAMD10D14A-SSNT - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD10D14A-SSNT

ATSAMD10D14A-SSNT - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip ATSAMD10D14A-SSNT is an ARM Cortex-M0+ based 32-bit flash microcontroller running at up to 48 MHz, with 16 KB of flash memory and 4 KB of SRAM, housed in a 20-pin SOIC (300 mil) package. It operates from 1.6 V to 3.6 V, includes the SAM D10D feature set, and is qualified for the -40C to +105C industrial temperature range. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory, data RAM, and peripherals. The Cortex-M0+ is ARM's smallest, most energy-efficient application processor, designed for deterministic embedded control in cost- and power-sensitive products. Within the broader product taxonomy, the ATSAMD10D14A sits in the hierarchy: ARM Cortex-M0+ MCU -> 32-bit microcontroller -> embedded processor -> semiconductor IC. SAM D10D devices reach 2.46 CoreMark/MHz, enabling responsive control loops at very low active current. Key features include the Cortex-M0+ core with single-cycle I/O access, 16 KB flash and 4 KB SRAM, a 12-channel 350 kSps 12-bit SAR ADC, two I2C and two SPI (SERCOM) peripherals, up to six UART-capable SERCOM channels, full-speed USB device support on related variants, and an Event System for inter-peripheral signalling without CPU wake-ups. The 20-pin SOIC package exposes 14 general-purpose I/O pins and supports capacitive touch via the Peripheral Touch Controller (PTC). The ATSAMD10D14A integrates Microchip's proprietary SERCOM architecture, where each of six SERCOM slots can be independently configured as I2C, SPI, or UART, allowing designers to map the exact peripheral mix their application needs. The 12-bit ADC delivers up to 350 kSps with hardware averaging and oversampling, while the integrated voltage regulator, brown-out detector, and PLL provide a stable 48 MHz system clock from the internal 8 MHz oscillator. Typical applications include home automation endpoints, low-cost consumer electronics, smart metering nodes, industrial sensor transmitters, and battery-powered IoT devices where the small 20-pin SOIC and wide 1.6 V to 3.6 V supply range enable direct lithium-cell or 3.3 V system-bus operation. Designers should pay particular attention to the decoupling network - Microchip recommends at least one 100 nF X7R ceramic on each VDD pin and a bulk 4.7 uF on the main rail - and should plan the SWD footprint even in production boards to keep firmware updates possible. This page consolidates current distributor pricing, pin-compatible drop-in alternatives in the SOIC-20 footprint, and design notes not always present on the manufacturer product page.

見積もり お問い合わせ
ATSAMD11C14A-SSNT - 48MHz Cortex-M0+ MCU, 16KB Flash, USB | Microchip
ATSAMD11C14A-SSNT

ATSAMD11C14A-SSNT - 48MHz Cortex-M0+ MCU, 16KB Flash, USB | Microchip

The Microchip ATSAMD11C14A-SSNT is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D11C family, featuring 16KB of flash memory, 4KB of SRAM, and an integrated full-speed USB 2.0 device controller. It runs at up to 48MHz and is housed in a 14-pin SOIC (150-mil / 3.90 mm) package operating from 1.6V to 3.6V. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ MCU is the smallest and most energy-efficient core in the Cortex-M family, designed for deeply embedded, cost-sensitive applications where low active current, deterministic interrupt latency, and small code footprint matter most. It belongs to the broader category of 32-bit microcontrollers -> RISC microcontrollers -> embedded processors -> integrated circuits -> semiconductors. The SAM D11C family is positioned at the entry level of Microchip's Atmel SMART SAM D lineup, optimized for simple migration with hex-compatible code across all peripheral modules. Key differentiating features include: 2.46 CoreMark/MHz efficiency, integrated USB 2.0 full-speed device, 6 SERCOM channels (configurable as UART/SPI/I2C), a 10-channel 350 kS/s 12-bit ADC, and an on-chip temperature sensor. The part supports SleepWalking peripherals that wake the CPU on a threshold event, drastically lowering average current in IoT battery-powered designs. The ATSAMD11C14A uses a single-wire SERCOM-debug programming interface, eliminating the need for a dedicated SWD header and saving board area. The 14-SOIC package exposes PA, PB, and additional I/O through the SERCOM multiplexing scheme, allowing designers to remap UART, I2C, or SPI on almost any pin. Typical applications include USB HID peripherals, sensor hubs, smart home nodes, consumer wearables, low-cost touch-button controllers, and industrial metering end-points. In USB human-interface-device designs the integrated transceiver removes the external 1.5 kohm pull-up, and the 2.46 CoreMark/MHz headroom leaves enough cycles for protocol stacks. When designing with this part, ensure the VDD decoupling follows Microchip's recommended 100 nF + 1 uF + bulk layout, and leave pin PA24 (USB DP) accessible. The 14-SOIC variant is best suited for hand-soldered prototypes and through-hole-feel-friendly assemblies; for high-density designs, the QFN/SSOP variants are available within the SAM D11 family. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
ATSAMD11C14A-SSUT - 32-bit ARM Cortex-M0+ MCU 48MHz 16KB Flash | Microchip
ATSAMD11C14A-SSUT

ATSAMD11C14A-SSUT - 32-bit ARM Cortex-M0+ MCU 48MHz 16KB Flash | Microchip

The Microchip Technology ATSAMD11C14A-SSUT is a 32-bit ARM Cortex-M0+ flash microcontroller (MCU) from the SAM D11C family, operating at up to 48 MHz with 16 KB of flash and 4 KB of SRAM in a 14-pin SOIC package. The part integrates a full Cortex-M0+ core with single-cycle multiplier, 6-channel SERCOM configurable serial communication, 10-channel 12-bit ADC, 10-bit DAC, and a full-speed USB 2.0 device controller, all in a small-outline industrial footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (flash), data memory (SRAM), and a rich set of peripheral interfaces. The Cortex-M0+ is the smallest, most energy-efficient ARM core designed for embedded applications, sitting at the bottom of the Cortex-M hierarchy (Cortex-M0/M0+ -> Cortex-M3 -> Cortex-M4 -> Cortex-M7). The SAM D11C series specifically adds native USB 2.0 full-speed and an integrated 48 MHz digital frequency-locked loop (DFLL) on-chip oscillator, which removes the need for an external crystal in USB applications. Key differentiating features include 16 KB flash with read-while-write support, 4 KB SRAM, up to 12 SERCOM pads that can each be configured as USART, I2C, or SPI, a 12-bit 350 ksps ADC with up to 10 channels, a 10-bit 350 ksps DAC, two analog comparators, two I2S interfaces, and a real-time clock. The device operates from 1.62 V to 3.63 V and is qualified for -40 C to +85 C industrial temperature range. The ATSAMD11C14A-SSUT's architecture uses a two-bus AHB-Lite matrix with a separate APB bridge, allowing DMA-driven SERCOM, ADC, and DAC operations to occur in parallel with CPU execution. The on-chip DFLL48M locks to the 32.768 kHz crystal reference to derive the 48 MHz USB clock, eliminating the BOM cost of a high-frequency external crystal. The peripheral event system and 6-channel DMA controller further reduce CPU overhead in real-time applications. Typical applications include USB HID peripherals (keyboards, mice, custom input devices), home automation sensor nodes, low-power wireless gateways with USB charging interfaces, consumer toys and wearables with USB-C connectivity, industrial meter reading equipment, and small motor-control daughterboards. The combination of native USB, small footprint, and Cortex-M0+ ecosystem support makes it well suited to volume-cost-sensitive designs that still need modern connectivity. When designing with this part, plan the PCB layout to keep the USB DP/DM traces length-matched within 4 mm and the 32.768 kHz crystal traces short and guarded. Decouple VDD with at least one 100 nF X7R capacitor placed within 2 mm of the pin, and add a 4.7 uF bulk capacitor for the USB VBUS rail. Program the DFLL before USB enumeration to meet USB 2.0 full-speed jitter specifications. This page consolidates distributor stock, AEC-Q100 sibling variants, and practical design notes not found in the manufacturer datasheet to accelerate your component selection and PCB bring-up.

見積もり お問い合わせ
ATSAMD11D14A-MNT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip
ATSAMD11D14A-MNT

ATSAMD11D14A-MNT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip

The Microchip ATSAMD11D14A-MNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D11D family, delivering up to 48 MHz CPU clock speed with 16 KB of Flash and 4 KB of SRAM, housed in a compact 24-pin QFN (4x4 mm) package with exposed thermal pad. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is an ultra-low-power 32-bit processor core designed by ARM Holdings and licensed to silicon vendors like Microchip. It belongs to the Cortex-M family of microcontrollers -> microcontrollers -> embedded processors -> integrated circuits. The M0+ core targets energy-efficient applications with a stripped-down instruction set, deterministic interrupt handling, and optional single-cycle I/O access, making it a popular entry point for cost-sensitive ARM designs. The ATSAMD11D14A-MNT integrates a full-speed USB 2.0 device controller, a six-channel DMA controller, a 32-bit RTC, two 16-bit Timer/Counters, and one 24-bit Timer/Counter for Control (TCC), up to 22 programmable I/O pins, and a 12-bit ADC with up to 350 ksps sampling rate. Its Serial Communication Interface (SERCOM) block provides up to six configurable channels for I2C, SPI, or UART, enabling flexible peripheral expansion without dedicated silicon. The device operates from 1.6 V to 3.6 V supply voltage and supports industrial temperature ranges. The integrated USB transceiver and on-chip PHY eliminate the need for external USB components, simplifying hardware design for HID, CDC, or vendor-class USB devices. The 24-QFN package provides excellent thermal performance for a small-footprint MCU. Typical applications include USB human-interface devices (HID), USB-to-serial converter dongles, low-power sensor hubs, home automation controllers, consumer electronics with USB connectivity, and industrial metering peripherals. When designing with this device, ensure proper USB impedance matching and bypass capacitor placement near VDD pins. The Cortex-M0+ core supports Thumb-2 subset instructions; firmware development is streamlined through Microchip's MPLAB X IDE and Atmel START toolchain.

見積もり お問い合わせ
ATSAMD11D14A-SSNT - 48MHz Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD11D14A-SSNT

ATSAMD11D14A-SSNT - 48MHz Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip ATSAMD11D14A-SSNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D11D family, offering 48 MHz CPU performance, 16 KB of Flash, and 4 KB of SRAM in a 20-pin SOIC package. It operates from 1.6 V to 3.6 V and integrates a full-speed USB 2.0 device interface, making it suitable for connected embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one silicon die. The Cortex-M0+ core is an ultra-low-power ARM processor designed for energy-efficient embedded applications; in the broader taxonomy it sits below Cortex-M3/M4 parts and above 8-bit microcontrollers in performance. The SAM D11D series specifically targets designs that need modern 32-bit performance with USB connectivity in compact packages. Key features of the ATSAMD11D14A-SSNT include the 48 MHz Cortex-M0+ core reaching 2.46 CoreMark/MHz, 16 KB of in-system programmable Flash, 4 KB SRAM, and an integrated USB 2.0 Full-Speed device controller with on-chip transceiver. The device also includes a SERCOM (serial communication) interface count of up to six, a 12-bit ADC, 10-bit DAC, and multiple timers. The 20-pin SOIC footprint keeps the solution footprint minimal while exposing enough I/O for typical sensor, motor, and human-interface nodes. The SAM D11D architecture uses a single-cycle hardware multiplier, tightly-coupled memory bus, and Microchip's proprietary peripheral event system that lets peripherals trigger each other without CPU intervention. SleepWalking I/O and multiple low-power modes (IDLE, STANDBY, BACKUP) reduce active current to well below 1 mA in deep sleep, allowing battery-powered designs to extend operating life. The integrated USB transceiver removes the need for an external PHY or precision resistors, simplifying USB device certification. Typical applications include USB HID peripherals, home automation nodes, consumer electronics such as remote controls and gaming accessories, metering endpoints, industrial sensor hubs, and low-cost IoT bridges. The combination of USB, ADC, and rich serial peripherals covers most connected-sensor use cases in a single chip. When designing with this part, note the 20-pin SOIC package shares the SAM D11D family footprint, enabling drop-in migration between pin-compatible family members. Use the Atmel/Microchip START code-configurator to generate initialization code and verify the USB peripheral against the latest USB device class stack for certification. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
ATSAMD11D14A-UUT - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD11D14A-UUT

ATSAMD11D14A-UUT - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip Technology ATSAMD11D14A-UUT is a 32-bit ARM Cortex-M0+ flash microcontroller operating at up to 48 MHz, with 16 KB of Flash and 4 KB of SRAM, housed in a 20-ball WLCSP package. It integrates a USB 2.0 Full-Speed device controller, a 6-channel SERCOM (serial communication) peripheral set, a 12-bit ADC, a 10-bit DAC, and a full-speed Host/Device USB transceiver on-chip, making it suitable for compact connected-embedded designs. What is a Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and peripherals. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M family, optimized for low-power embedded applications. Microcontrollers sit in the broader hierarchy of microprocessors -> ARM Cortex-M -> Cortex-M0+ -> microcontroller unit -> semiconductor, and SAM D11 devices target low-power, deterministic control with code-density advantages over 8-bit MCUs. Key features of the ATSAMD11D14A-UUT include up to six SERCOM channels configurable as I2C, SPI, or UART, six 16-bit Timer/Counters (TC), a Real-Time Counter (RTC), a 12-channel 350 kbps 12-bit ADC, a 10-bit 350 kbps DAC, and an on-chip Full-Speed USB 2.0 transceiver. The device also features a 32-bit Event System for inter-peripheral signalling without CPU intervention, a Peripheral Touch Controller (PTC) for capacitive sensing, and a 32.768 kHz RTC with calendar mode. Architecturally, the SAM D11 family uses a single-cycle I/O bus, a single-cycle multiplier, and a tightly-coupled SRAM implementation that yields 2.46 CoreMark/MHz performance. An integrated low-power voltage regulator and multiple sleep modes (IDLE, STANDBY, BACKUP) enable typical active currents around 3 mA at 48 MHz and deep-sleep currents below 1 uA, depending on configuration. Typical applications include USB HID peripherals, smart-home sensor nodes, consumer wearables, low-cost home-automation hubs, capacitive-touch user interfaces, and industrial metering. The 20-ball WLCSP footprint suits space-constrained designs such as PC accessories, USB dongles, and small IoT sensor pods. Operating temperature spans -40C to +85C. A key design consideration is the WLCSP assembly: PCB land-pattern design must follow Microchip IPC-7351 WLCSP guidelines to ensure reliable reflow. The 20-ball WLCSP shares a footprint with the SAM D10D family, allowing upward/downward migration with identical peripheral IP. This page synthesizes Microchip datasheet data, distributor pricing, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.

見積もり お問い合わせ
ATSAMD20E14A-AN - SAM D20 ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip
ATSAMD20E14A-AN

ATSAMD20E14A-AN - SAM D20 ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip

The Microchip Technology ATSAMD20E14A-AN is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20 family, delivering up to 48 MHz core performance with 16 KB of Flash and 2 KB of SRAM in a 32-pin TQFP (7x7 mm) package. It operates from 1.62V to 3.63V and integrates a 12-bit ADC, 10-bit DAC, and up to 6 SERCOM serial communication interfaces, making it a versatile mixed-signal MCU for embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripherals such as ADCs, timers, and communication controllers into one package. Within the semiconductor hierarchy, an MCU belongs to the broader class of integrated circuits (ICs) and is a key member of the embedded systems domain alongside microprocessors, DSPs, and FPGAs. The ATSAMD20E14A-AN specifically targets the low-power, deterministic end of the Cortex-M0+ market, balancing processing headroom with energy efficiency for always-on battery-powered products. Key features of the ATSAMD20E14A-AN include the ARM Cortex-M0+ core with single-cycle I/O access, the Peripheral Touch Controller (PTC) supporting capacitive touch buttons and sliders, a full-speed USB 2.0 device interface (when paired with an external 48 MHz source), and Microchip's SERCOM modules that can be configured as UART, SPI, or I2C. The device also includes a Real-Time Clock (RTC), event system for inter-peripheral signalling without CPU intervention, and a SleepWalking mechanism that allows peripherals to wake the CPU only when meaningful events occur. The architecture uses a 2-layer AHB bus matrix with separate bridges for ICODE/DCODE and the peripheral bridge, minimizing latency for deterministic interrupt response. The integrated voltage regulator supports a wide 1.62V to 3.63V supply range and can deliver the full 48 MHz across the entire range, simplifying battery and USB-powered designs. Typical applications include home automation control panels, smart metering nodes, capacitive-touch user interfaces, low-power wireless sensor hubs, consumer electronics peripherals, and industrial control modules. Its low-power Sleep modes (down to a few microamperes) make it especially well-suited to battery-operated devices where idle current dominates the energy budget. When designing with this part, place a 100 nF decoupling capacitor close to each VDD pin and a 4.7 µF bulk capacitor at the regulator output. Configure unused pins as inputs with internal pull-up to minimise quiescent current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for SAM D20 selection.

見積もり お問い合わせ
ATSAMD20E14A-AUT - Cortex-M0+ MCU 48MHz 16KB FLASH TQFP-32
ATSAMD20E14A-AUT

ATSAMD20E14A-AUT - Cortex-M0+ MCU 48MHz 16KB FLASH TQFP-32

The Microchip Technology ATSAMD20E14A-AUT is an ARM Cortex-M0+ based 32-bit flash microcontroller operating at up to 48 MHz, integrating 16 KB of Flash and 2 KB of SRAM, and packaged in a 32-pin TQFP (7x7 mm) for surface-mount assembly. An ARM Cortex-M0+ microcontroller is a low-power, energy-efficient 32-bit processor core widely used in embedded systems. It belongs to the Cortex-M family (Cortex-M0, M0+, M3, M4, M7) — a hierarchy of ARM cores targeted at microcontrollers rather than application processors. Cortex-M0+ sits at the low-power/low-cost end, offering Thumb-2 instruction set efficiency, single-cycle I/O access, and an optional Micro Trace Buffer. This positions the ATSAMD20E14A-AUT as a bridge between traditional 8-bit MCUs and higher-end Cortex-M3/M4 devices. The ATSAMD20E14A-AUT features the SAM D20 peripheral set including a 12-channel SERCOM (configurable as I2C/SPI/USART), a 12-bit ADC with up to 10 channels, a 10-bit DAC, two analog comparators, and a 16-bit timer/counter. Six configurable SERCOM ports give multi-protocol serial flexibility. An Event System, Peripheral Touch Controller (PTC), and full-speed USB device interface complete the peripheral mix. The device supports 1.62 V to 3.63 V operation with multiple low-power modes (Idle, Standby, Backup, Hibernate). The architecture combines a deterministic Cortex-M0+ core with Microchip's proprietary low-power techniques, achieving Active current below 70 µA/MHz and full-Stop mode retention below 5 µA. On-chip peripherals connect to the CPU via the AHB-APB bridge and event system, enabling fast inter-peripheral signalling without CPU intervention. An integrated 32 kHz RTC oscillator and PLL multiply the internal 8 MHz RC oscillator up to 48 MHz system clock. Typical applications include home automation nodes, consumer electronics, smart metering, industrial sensor interfaces, and battery-powered IoT endpoints where 32-bit performance and ultra-low sleep current are both required. The TQFP-32 footprint suits hand-solderable prototypes while remaining production-friendly. Designers should note that the ATSAMD20E14A-AUT requires the Atmel/Microchip ASF or MPLAB Harmony 3 framework, and programming via SWD using tools such as MPLAB X IDE / PICkit 4. Pin 1 (VDDIN) must be properly decoupled for stable core operation. This page synthesizes distributor pricing, drop-in alternatives across the SAM D20 family, and practical design notes drawn from manufacturer documentation, going beyond what a single datasheet chapter covers.

見積もり お問い合わせ
ATSAMD20E14A-MNT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash, 32-VQFN
ATSAMD20E14A-MNT

ATSAMD20E14A-MNT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash, 32-VQFN

The Microchip Technology ATSAMD20E14A-MNT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20E family, operating up to 48 MHz with 16 KB of Flash and 2 KB of SRAM in a 32-pin VQFN (5x5 mm) package with exposed pad. It supports 1.62V-3.63V supply, integrates a 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), RTC, and up to six SERCOM serial interfaces, delivering 2.14 CoreMark/MHz efficiency for low-power embedded applications. An ARM Cortex-M0+ microcontroller is an entry-level 32-bit MCU core built on the ARMv6-M architecture, optimized for energy efficiency and deterministic performance in cost-sensitive applications. Within the broader taxonomy, the Cortex-M0+ sits beneath Cortex-M3/M4/M7 cores, belongs to the microcontroller (MCU) family, falls under microcontrollers, then Integrated Circuits, and ultimately semiconductors. The SAM D20 series specifically targets low-power IoT and consumer designs where 8-bit MCUs previously dominated. Key features of the ATSAMD20E14A-MNT include SleepWalking peripherals, an Event System for inter-peripheral signaling without CPU wakeup, six SERCOM channels configurable as I2C/SPI/UART, a 12-bit 350 kSPS ADC with up to 10 channels, a 10-bit 350 kSPS DAC, and an integrated PTC supporting up to 256 touch channels for capacitive button/slider designs. The device operates across -40C to +105C (industrial grade, per Mouser listing) and consumes < 70 uA/MHz active. The MCU integrates a single-cycle hardware multiplier, NVIC with 32 interrupt lines, and a 24-bit SysTick timer. The peripheral event system and SERCOM configurability enable flexible pin mapping, simplifying PCB routing versus fixed-function MCUs. The 32-VQFN (5x5) package with exposed thermal pad (EP) supports -40C to +125C operation with AEC-Q100 compliance for automotive use cases when paired with the appropriate variant. Typical applications include home automation nodes, smart metering, industrial sensor hubs, consumer electronics with capacitive touch UI, low-power wireless sensor platforms, and battery-powered IoT endpoints. The wide 1.62V-3.63V supply range permits direct operation from single-cell Li-ion or 3.3V regulated rails. Design tip: route the SERCOM peripheral mapping during schematic capture to avoid costly layout rework - each of the six SERCOMs can be assigned to specific I/O pins, and choosing pins early simplifies later pinout changes. This page consolidates distributor pricing, same-family alternatives (ATSAMD20E15A-MNT, ATSAMD20E16A-MNT, ATSAMD20E17A-MNT, ATSAMD20E18A-MNT), drop-in cross-brand equivalents, and practical design guidance beyond what the manufacturer datasheet offers alone.

見積もり お問い合わせ
ATSAMD20E14A-MU - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip
ATSAMD20E14A-MU

ATSAMD20E14A-MU - 48MHz Cortex-M0+ MCU 16KB Flash | Microchip

The Microchip Technology ATSAMD20E14A-MU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D20 family, operating at up to 48 MHz and delivering 2.14 CoreMark/MHz. The device integrates 16 KB of Flash and 2 KB of SRAM in a 32-pin VQFN (5x5 mm) package with an exposed thermal pad, and is supplied across an industrial 1.62V to 3.63V core voltage range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ATSAMD20E14A-MU belongs to the Cortex-M0+ class of microcontrollers, the most energy-efficient ARM core for embedded use; within the broader taxonomy, it sits as MCU -> 32-bit MCU -> ARM Cortex-M MCU -> low-power MCU -> embedded microcontroller. Its Cortex-M0+ core is binary-compatible with the Thumb instruction set, simplifying toolchain reuse across the SAM D product line. Key differentiating features include the SAM D20 Event System for inter-peripheral signalling without CPU intervention, a 12-channel 350 kbps SERCOM configurable serial engine, and a 6-channel 12-bit 350 ksps ADC with hardware averaging. The part also integrates a 10-bit 350 ksps DAC, two analog comparators, a 32 kHz RTC, and full-speed USB 2.0 device with on-chip transceiver, all packaged in 32-pin VQFN. According to the Microchip/Atmel SAM D20 datasheet, these peripherals are routed via a low-power bus matrix, allowing deterministic 1.66 µs wake-up from deep-sleep retention. Architecturally, the ATSAMD20E14A-MU uses a single-bank Flash memory with embedded EEPROM emulation through the NVM controller, hardware CRC, and a true random number generator (TRNG). The Power Manager implements six SleepWalking-enabled peripheral clocks, three sleep modes (IDLE, STANDBY, BACKUP) and a 7 µA typical BACKUP current with RTC running, positioning the part for battery-driven IoT endpoints. Typical applications include home-automation smart sensors, low-power wireless sensor nodes (when paired with an external sub-GHz transceiver), consumer HID peripherals, industrial metering, capacitive-touch human interfaces, and small-footprint USB-CDC devices. The wide operating range also supports outdoor asset-tracking tags. When designing with this device, verify your linker script reserves the upper 1 KB of SRAM for the Atmel Start/Device Library heap, and always bond the exposed pad to a continuous ground pour to meet the 31.6 °C/W theta_JB thermal path. This page synthesizes verified distributor pricing, drop-in alternatives from Microchip's own cross-reference tool, and engineering design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
ATSAMD20E14B-AU - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD20E14B-AU

ATSAMD20E14B-AU - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip ATSAMD20E14B-AU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20E family, delivering up to 48 MHz core performance with 16 KB of Flash and 2 KB of SRAM in a 32-pin TQFP (7x7 mm) package. It operates from a wide 1.62 V to 3.63 V supply and integrates a 6-channel SERCOM, 12-bit 350 ksps ADC, 10-bit DAC, and multiple timers, balancing low power consumption with rich peripheral integration. The part is rated for the industrial temperature range (-40 C to +85 C) and is qualified to the Microchip AEC-Q100 grade-2 screening flow for harsh environments. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by Arm for energy-efficient embedded applications. As part of the microcontroller hierarchy, it sits above 8/16-bit legacy cores and below Cortex-M3/M4/M7 devices, pairing a Thumb-2 instruction subset with a single-cycle I/O port for deterministic GPIO response. Within the SAM D20 family, the E (32-pin) variants are the smallest-footprint members, optimized for cost-sensitive and space-constrained designs. Key features include a 12-bit 350 ksps ADC with up to 14 analog channels, a 10-bit 350 ksps DAC, six SERCOM (serial communication) interfaces configurable as UART, SPI, or I2C, full-speed USB 2.0 device support, and a Peripheral Touch Controller (PTC) supporting capacitive buttons, sliders, and proximity sensors. The Cortex-M0+ core executes the Thumb instruction set with deterministic 1.77 DMIPS/MHz performance, supported by a 4-channel DMA engine that offloads memory transfers to reduce CPU load. The integrated event system allows peripherals to trigger each other without CPU intervention, further lowering average power consumption. Architecturally, the device uses a single AHB-Lite bus matrix with a separate APB bridge for low-speed peripherals, allowing concurrent SERCOM transfers and ADC sampling. The power manager supports Idle, Standby, and Backup sleep modes with wake-on-interrupt and RTC-driven wake from backup, achieving currents down to the single-digit microamp range. On-chip voltage regulation generates the core logic supply from a single external rail, simplifying BOM and PCB layout. Typical applications include smart-home sensor hubs, low-power IoT edge nodes, capacitive-touch user interfaces for appliances, industrial sensor transmitters, USB HID peripherals, and battery-driven consumer devices such as fitness wearables. The combination of USB device, ADC, and PTC also suits data loggers and Human Interface Device (HID) designs. When designing with this part, allocate one decoupling capacitor per VDD pin (100 nF X7R plus a bulk 1 uF-4.7 uF), keep SERCOM signal traces short to avoid EMI, and connect unused I/O to VDD or GND through software-enabled pull resistors to reduce sleep current. Programming is supported through the SWD interface using Atmel/Microchip Studio, MPLAB X, or pyOCD. This page consolidates distributor pricing, drop-in pin-compatible alternatives, application circuits, and PCB design notes to help engineers evaluate the ATSAMD20E14B-AU for both new designs and legacy upgrades.

見積もり お問い合わせ
ATSAMD20E14B-AUT - 48MHz Cortex-M0+ MCU, 16KB Flash, 32-TQFP | Microchip
ATSAMD20E14B-AUT

ATSAMD20E14B-AUT - 48MHz Cortex-M0+ MCU, 16KB Flash, 32-TQFP | Microchip

The Microchip Technology ATSAMD20E14B-AUT is a 32-bit ARM Cortex-M0+ based flash microcontroller from the SAM D20E family, running up to 48 MHz, with 16 KB Flash and 2 KB SRAM, housed in a 32-pin TQFP (7x7 mm) industrial-temperature grade package. The part number suffix "-AUT" denotes TQFP package, industrial temperature range (-40C to +85C), and tape-and-reel packaging. The ATSAMD20E14B-AUT delivers low-power, high-performance processing suitable for home automation, consumer, metering, and industrial applications. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is a 32-bit reduced instruction set computing (RISC) MCU designed for ultra-low power embedded applications. It belongs to the broader ARM Cortex-M processor family, which sits inside the hierarchy: ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded IC. The M0+ core uses the Thumb/Thumb-2 instruction set, a single-cycle multiplier, and a tightly coupled NVIC interrupt controller. Compared with 8-bit MCUs such as the PIC16F series, the M0+ offers higher code density, modern toolchain support, deterministic interrupt latency, and far better DMIPs/mW efficiency, while still consuming minimal power. Key features of the ATSAMD20E14B-AUT include: ARM Cortex-M0+ core with Single-cycle multiplier, hardware divide, and debug access via SWD; 16 KB Flash and 2 KB SRAM with in-application programmable flash; 6 SERCOM (configurable serial communication) interfaces supporting I2C, SPI, and USART simultaneously; 12-bit ADC with up to 350 ksps throughput and 10 channels; up to 14 touch-channel support via the Peripheral Touch Controller (PTC); and 1.62V to 3.63V single-supply operation with on-chip voltage regulator. Technically, the SAM D20E integrates an 8-channel Event System, 6-channel DMA controller, Real-Time Counter (RTC), and multiple 16-bit Timer/Counters (TC). Memory protection is provided through a configurable flash access window, and security is enhanced by a 128-bit unique chip ID. The part supports Sleep, Idle, Standby, and Backup sleep modes with fast wake-up, drawing as little as a few microamps in deep-sleep, which is critical for battery-powered IoT endpoints. Typical applications include IoT sensor nodes, smart-home wireless controllers (when paired with an ATWINC1500 Wi-Fi module), industrial motor control boards (using the TC/PWM channels), battery-powered metering devices such as water/gas meters, consumer HMI products with touch-button UIs, and low-cost wearable electronics. The SERCOM flexibility lets the MCU speak multiple protocols concurrently without external glue logic. When designing with this part, allocate the 32-pin TQFP's VDD/GND pair to a star-ground layout with 100 nF + 1 uF decoupling close to each supply pin. Use the SERCOM pins thoughtfully because pin mapping to each SERCOM is multiplexed across the 32 TQFP pins, and choosing early avoids PCB rework. For low-power battery designs, leverage the integrated PTC for cap-touch wake-up, avoiding external wake controllers. This page synthesizes distributor pricing, validated drop-in alternatives (same Microchip family), and engineering notes for the ATSAMD20E14B-AUT in one place - data not consolidated in the manufacturer datasheet.

見積もり お問い合わせ
ATSAMD20E14B-MUT - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip
ATSAMD20E14B-MUT

ATSAMD20E14B-MUT - 48MHz ARM Cortex-M0+ MCU, 16KB Flash | Microchip

The Microchip Technology ATSAMD20E14B-MUT is an ARM Cortex-M0+ based 32-bit microcontroller from the SAM D20E family, delivering up to 48 MHz CPU clock speed with 16KB Flash and 2KB SRAM in a 32-pin VQFN (5x5 mm) package. It operates from 1.62V to 3.6V supply and integrates 6 channels of 12-bit ADC, multiple SERCOM interfaces, and a full-featured peripheral set. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed for ultra-low-power embedded applications. It sits within the broader hierarchy: Cortex-M0+ -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The M0+ core delivers Thumb-2 instruction efficiency with a deterministic 2-stage pipeline, making it ideal for cost-sensitive, energy-aware designs. Key features of the ATSAMD20E14B-MUT include 16KB Flash for application code, 2KB SRAM for data, up to 26 GPIO pins, 6 SERCOM channels for flexible UART/SPI/I2C configuration, a 12-bit 350 ksps ADC with up to 16 channels, and integrated SleepWalking peripherals with Event System for sub-microamp sleep current. The device also supports a crystal-less USB bootloader via the DSU (Device Service Unit) and integrates a true 32.768 kHz RTC. The ATSAMD20E14B-MUT uses an advanced low-power architecture with multiple sleep modes (IDLE, STANDBY, BACKUP), consuming as little as 3.5 uA in BACKUP mode with RTC running. Its peripheral Event System allows direct inter-peripheral signaling without CPU wake, drastically reducing average power in sensor-driven applications. Typical applications include smart home automation (Zigbee/BLE endpoints), low-power IoT sensor nodes, consumer electronics (HID, toys), industrial metering, and battery-powered portable devices. The combination of small package size, deep-sleep current, and rich peripherals makes it a strong fit for energy-harvesting designs. Designers should pay attention to decoupling (one 100nF per VDD pin), exposed-pad grounding (mandatory for thermal dissipation on VQFN), and use Atmel Studio 7 or MPLAB X IDE with the DSU to enable field upgrades via USB without an external programmer. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that are not gathered in a single place inside the manufacturer datasheet, helping engineers select and source the part quickly.

見積もり お問い合わせ
ATSAMD20E15A-AN - 32KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD20E15A-AN

ATSAMD20E15A-AN - 32KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20E15A-AN is a low-power, high-performance 32-bit ARM Cortex-M0+ based flash microcontroller (MCU) featuring 32KB of Flash and 4KB of SRAM, housed in a 32-pin TQFP package. It operates at up to 48MHz clock frequency from a wide 1.62V to 3.63V supply, delivering 2.14 CoreMark/MHz and integrating 12-bit ADC, 10-bit DAC, 256-channel Peripheral Touch Controller (PTC), and a full RTC subsystem. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M processor family, designed for embedded applications where deterministic real-time response and ultra-low power consumption are required. The SAM D20 sits in the hierarchy as: Cortex-M0+ core -> ARM Cortex-M family -> 32-bit RISC microcontroller -> embedded processor -> semiconductor IC, making it ideal for cost-sensitive yet feature-rich IoT and consumer designs. Key differentiating features include the SERCOM (Serial Communication Interface) modules that can be independently configured as UART, SPI, or I2C, plus a hardware Peripheral Touch Controller for capacitive touch buttons and sliders without external components. The 12-bit ADC delivers up to 350ksps with internal voltage reference, while the 10-bit DAC supports waveform generation. Multiple Sleep modes (Idle, Standby, Backup) and a dedicated RTC with calendar mode achieve sleep currents below 5 microamps. Typical applications span home automation endpoints (smart thermostats, sensor hubs), consumer electronics (wearable accessories, toys), metering (energy and water monitors), and industrial controls (HMI panels, low-end PLCs). The wide 1.62V to 3.63V operating range and AEC-Q100 qualified variants simplify designs that target both battery-powered and 24V industrial bus environments. When designing with the ATSAMD20E15A-AN, ensure the on-chip voltage regulator's bulk capacitor meets Microchip's reference design (typically 1uF X7R). Decoupling capacitors should be placed within 2mm of each supply pin, and unused SERCOM pads can be repurposed as GPIO. Programming is supported via Atmel-ICE or Curiosity Nano boards through the SWD interface.

見積もり お問い合わせ
ATSAMD20E15A-AU - ARM Cortex-M0+ 48MHz 32KB Flash MCU | Microchip
ATSAMD20E15A-AU

ATSAMD20E15A-AU - ARM Cortex-M0+ 48MHz 32KB Flash MCU | Microchip

The Microchip ATSAMD20E15A-AU is a 32-bit ARM Cortex-M0+ based flash microcontroller from the SAM D20E family, operating at up to 48 MHz with 32 KB of Flash and 4 KB of SRAM, housed in a 32-pin TQFP (7x7 mm) industrial-grade package. It integrates a 12-bit ADC, 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), an RTC, and a full SERCOM peripheral set, making it a low-power yet high-performance general-purpose MCU for embedded designs. What is a Cortex-M0+ microcontroller? The ARM Cortex-M0+ is the smallest and most energy-efficient Cortex-M core; it executes the Thumb/Thumb-2 instruction set, provides single-cycle IO, a 32-bit hardware multiplier, and a Nested Vectored Interrupt Controller (NVIC). Microcontrollers (MCUs) integrate CPU core, non-volatile memory (Flash), volatile memory (SRAM), and peripherals on a single die, forming the smallest complete compute node in an embedded system hierarchy that ascends: Cortex-M0+ -> ARM Cortex-M family -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key features of the ATSAMD20E15A-AU include: 48 MHz Cortex-M0+ core, 32 KB Flash / 4 KB SRAM, 12-bit 200 ksps ADC with up to 10 analog channels, 10-bit DAC, six SERCOM ports (configurable as UART/SPI/I2C), 256-channel PTC for touch interfaces, Sleepwalking peripherals, and an integrated RTC. The device supports 1.62 V to 3.63 V supply operation and offers multiple low-power modes including IDLE, STANDBY, BACKUP, and OFF, with typical active current around 3.6 mA at 48 MHz. The architecture pairs a deterministic Cortex-M0+ pipeline with Microchip's Event System for inter-peripheral signaling without CPU intervention, plus a 6-channel DMA controller and SleepWalking logic that lets peripherals operate autonomously while the core remains in standby. The 12-bit ADC delivers up to 200 ksps with oversampling and hardware averaging. Typical applications include home automation endpoints, consumer electronics, smart metering, industrial sensor nodes, capacitive-touch human-machine interfaces, low-power wireless sensor hubs, and battery-powered IoT devices. The wide operating voltage and rich peripheral mix let a single MCU serve as the system controller. When designing with this device, place decoupling capacitors (100 nF and bulk) close to the VDD pin, and respect the trace-length guidelines for VDDCORE/VDDIO when tying the internal LDO to the core rail; use Atmel/Microchip Studio or MPLAB X IDE for code development. This page synthesizes distributor stock data, drop-in alternatives, and practical design notes not consolidated on the manufacturer datasheet.

見積もり お問い合わせ
ATSAMD20E15A-AUT - Cortex-M0+ 48MHz 32KB Flash MCU | Microchip
ATSAMD20E15A-AUT

ATSAMD20E15A-AUT - Cortex-M0+ 48MHz 32KB Flash MCU | Microchip

The Microchip Technology (formerly Atmel) ATSAMD20E15A-AUT is a 32-bit ARM Cortex-M0+ flash microcontroller running at up to 48 MHz, integrating 32 KB of Flash and 4 KB of SRAM, housed in a 32-pin TQFP (7x7 mm) package with industrial -40C to +85C operating range. The AUT suffix indicates the Tape & Reel shipping form. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one silicon die. The Cortex-M0+ is the most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time embedded control with a 2-stage pipeline, Thumb-2 instruction set, and a Nested Vectored Interrupt Controller (NVIC). Within the broader taxonomy, the ATSAMD20E15 belongs to the SAM D20 family of low-power Cortex-M0+ MCUs, which sits under the Microchip megaAVR/SAM umbrella of 8-bit and 32-bit embedded controllers. Key features include the SERCOM-configurable serial interface (configurable as UART, SPI, or I2C), a 12-bit ADC with up to 16 channels, a 10-bit DAC, multiple 16-bit Timer/Counters (TC), a Real-Time Counter (RTC), and the Peripheral Event System for hardware-triggered inter-peripheral signaling without CPU intervention. The device operates from 1.62V to 3.63V, supports Sleep, Idle, Standby and Backup low-power modes, and integrates an 8-channel Direct Memory Access (DMAC) controller. Architecturally, the SAMD20E series uses a single-cycle hardware multiplier, an internal 8 MHz and 32.768 kHz oscillator block, and a 6-channel SERCOM array that lets each peripheral be reassigned to most pins, simplifying PCB layout. The chip is supported by Microchip Studio (formerly Atmel Studio) and the MPLAB X IDE ecosystem, including ASF (Advanced Software Framework) and START code generators. Typical applications include home automation endpoints, smart metering, consumer electronics HMI, industrial sensor nodes, low-power IoT edge devices, and battery-powered wearables where active current in the single-digit mA range and sub-microamp sleep currents extend battery life. When designing with the SAMD20, choose your VDD rail between 1.62V and 3.63V and reserve the SWD pins (SWDIO/SWCLK) for in-system programming. Take advantage of the SERCOM multiplexer to keep PCB routing flexible, and use the Peripheral Event System to offload timing-critical tasks from the CPU. This page synthesizes distributor pricing, drop-in SAM D20 family alternatives, and practical design notes not found in the standalone Microchip datasheet.

見積もり お問い合わせ
ATSAMD20E15A-MN - 32KB Flash Cortex-M0+ MCU 48MHz 32-VQFN
ATSAMD20E15A-MN

ATSAMD20E15A-MN - 32KB Flash Cortex-M0+ MCU 48MHz 32-VQFN

The Microchip Technology ATSAMD20E15A-MN is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20E series, delivering 48 MHz CPU performance with 32 KB of Flash and 4 KB of SRAM in a 32-pin VQFN (5x5 mm) package with exposed thermal pad. It operates from 1.6 V to 3.6 V, integrates a rich peripheral set including SERCOM, ADC, timers, and event system, and is rated for the -40C to +105C industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile memory (SRAM), non-volatile program memory (Flash/ROM), and a configurable set of peripheral interfaces (GPIO, ADC, timers, communication controllers). The ATSAMD20E15A-MN belongs to the ARM Cortex-M0+ family - the most energy-efficient ARM core, designed for deterministic 32-bit processing in cost- and power-sensitive applications. Within Microchip's product hierarchy it sits under: ARM Cortex-M0+ MCU -> SAM D20 family -> SAM D20E sub-family (32-pin) -> power-management / industrial IoT / consumer segment. Key features include 48 MHz Cortex-M0+ core reaching 2.14 Coremark/MHz, 32 KB Flash, 4 KB SRAM, six SERCOM channels (configurable as UART/SPI/I2C), a 12-bit ADC with up to 20 analog channels, multiple 16-bit timers, a 32-bit Real-Time Counter, and the Microchip Event System for inter-peripheral signaling without CPU intervention. The device also integrates a full-speed USB 2.0 device controller on selected variants and supports the Atmel/Microchip SleepWalking energy-saving scheme, allowing peripherals to wake the core autonomously only when needed. Architecturally, the SAM D20E uses a single-cycle IO-bus to peripherals and a low-leakage process, which together deliver low active current (~7 mA at 48 MHz) and multiple low-power modes (IDLE, STANDBY, BACKUP) consuming only a few microamps. The integrated voltage regulator and brown-out detector simplify power-tree design, while the 32-VQFN exposed pad provides a low theta-JA path for thermal relief in space-constrained boards. Typical applications include home automation nodes, smart metering, low-cost consumer electronics, sensor hubs, industrial control peripherals, USB HID/HID-class devices, and battery-powered IoT endpoints. The combination of Cortex-M0+ efficiency, 32 KB Flash sufficient for many connectivity stacks (BLE host via UART, sub-GHz radio drivers, LoRaWAN device code), and a compact 5x5 mm package makes this part a strong fit where STM32L0 or older Atmel SAM3N parts were traditionally specified. When designing with this device, ensure the VQFN exposed pad is soldered to a sufficiently large copper pour for thermal dissipation, place decoupling capacitors (100 nF + 1 uF) as close as possible to VDD/VDDIO pins, and respect the 1.6 V minimum supply at start-up. For firmware, use the Microchip MPLAB X IDE with the MPLAB Harmony 3 framework or ASF to access the SERCOM multiplexing and Event System drivers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet to accelerate engineering selection.

見積もり お問い合わせ
ATSAMD20E15A-MNT - 32KB Flash Cortex-M0+ MCU | Microchip
ATSAMD20E15A-MNT

ATSAMD20E15A-MNT - 32KB Flash Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20E15A-MNT is a 32-bit ARM Cortex-M0+ based flash microcontroller running at 48 MHz, with 32 KB Flash and 4 KB SRAM, housed in a 32-pin VQFN (5x5 mm) package. The part operates from 1.62 V to 3.63 V, supports up to six SERCOM communication interfaces, and integrates a 12-channel 350 ksps 12-bit ADC plus two analog comparators. It is the smallest-pin-count member of Microchip's SAM D20 family and is offered in tape-and-reel packaging (MNT suffix) for high-volume SMT assembly. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as ADCs, timers, and communication controllers. Within the broader taxonomy, the ATSAMD20E15A belongs to the category of 32-bit microcontrollers -> ARM Cortex-M0+ microcontrollers -> low-power MCUs -> embedded controllers -> semiconductors. ARM Cortex-M0+ cores are favored for their deterministic interrupt response, Thumb-2 instruction set efficiency, and ultra-low active/idle power, making them ideal for always-on battery-powered applications. Key features of this device include the SAM D20 Event System for hardware-triggered inter-peripheral signalling without CPU intervention, six SERCOM modules each configurable as I2C/SPI/UART, a 12-bit 350 ksps ADC with up to 20 analog input channels via the AIN mux, and dual analog comparators with window mode. The device also integrates a 32.768 kHz RTC oscillator domain and full-speed USB device support is NOT available on the 32-pin variant - that requires the D20J (64-pin). Architecturally, the SAM D20 uses Microchip's proprietary low-power techniques including a separated SleepWalking peripheral domain, multiple power domains (PD0/PD1/PD2), and a backup register domain retained through deepest sleep. The Cortex-M0+ core delivers 2.14 CoreMark/MHz and supports single-cycle GPIO access through the IOBUS peripheral, enabling fast bit-banging for WS2812 LEDs or other timing-sensitive protocols. Typical applications include IoT sensor nodes, home automation endpoints, industrial control sub-modules, consumer wearable MCUs, smart metering, and low-cost HMI touch-button interfaces. The wide operating voltage range (1.62-3.63 V) makes it directly compatible with 1.8 V, 2.5 V, and 3.3 V power rails commonly used in modern SoC companion designs. When designing with this MCU, allocate the 32 KB Flash budget carefully: a typical USB stack or graphics library will not fit, but bare-metal or FreeRTOS-based sensor applications have ample headroom. Ensure the VQFN-5x5 thermal pad is soldered to a grounded copper pour of at least 10 mm² for proper thermal dissipation and electrical grounding of the exposed pad. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet. Compared to vendor product pages, this entry emphasizes pin-compatible family members, AEC-Q100 variants for automotive, and validated same-package drop-in replacements for shortage mitigation.

見積もり お問い合わせ
ATSAMD20E15B-AU - 48MHz Cortex-M0+ MCU, 32KB Flash | TQFP-32
ATSAMD20E15B-AU

ATSAMD20E15B-AU - 48MHz Cortex-M0+ MCU, 32KB Flash | TQFP-32

The Microchip Technology ATSAMD20E15B-AU is a 32-bit ARM Cortex-M0+ flash microcontroller running up to 48 MHz with 32 KB of Flash and 4 KB of SRAM, housed in a 32-pin TQFP (7x7 mm) package rated for industrial temperature operation. Per the Microchip SAM D20E family datasheet, the device integrates a 12-bit ADC, 10-bit DAC, multiple SERCOM modules, and a peripheral touch controller, targeting low-power embedded designs. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core implementing the Thumb/Thumb-2 instruction set, optimized for energy efficiency and deterministic interrupt response in cost-sensitive embedded applications. The Cortex-M0+ sits at the entry level of the Cortex-M family and is widely used in home automation, consumer electronics, metering, and industrial sensor nodes where small code size and low active/idle power are required. The SAM D20E series places this core inside Microchip's Atmel-derived ecosystem, adding on-chip analog and event-system peripherals. Key features of the ATSAMD20E15B-AU include 32 KB Flash with ECC, 4 KB SRAM, six SERCOM channels configurable as UART/SPI/I2C, a 12-bit 350 ksps ADC with up to 10 analog channels, a 10-bit 350 ksps DAC, an internal 8 MHz RC oscillator plus 32 kHz crystal support, and a sleep-mode current in the microamp range. The device operates from 1.62 V to 3.63 V across the industrial -40C to +85C temperature range, simplifying multi-rail designs. The architecture pairs the Cortex-M0+ core with a multi-layer AHB/APB bus matrix, a low-power RTC, and the Peripheral Event System that lets peripherals trigger each other without CPU intervention. This event routing is the SAM D20 family's main power-saving tool, allowing the core to stay in deep-sleep while timers, comparators, or SERCOM wake it only on real activity. The 12-bit ADC achieves typical INL of +/-1.5 LSB and supports both single-ended and differential inputs via the on-chip analog multiplexer. Typical applications include smart-home sensor hubs, low-power wireless sensor nodes (when paired with an external transceiver), industrial metering and HVAC controllers, consumer appliances with capacitive touch interfaces, and battery-powered IoT endpoints. The combination of Cortex-M0+ determinism and rich analog integration makes the device a strong fit when an 8-bit AVR is no longer adequate but a Cortex-M4 is overkill. When designing with this part, ensure the VDDCORE pin is decoupled per the SAM D20 reference schematic (typically 1 uF plus 100 nF), select the correct OSCSEL fuse for the chosen clock reference, and use Microchip's ASF/MPLAB Harmony framework to take advantage of the event-driven peripheral architecture. Watch out for pin-out differences between the QFN/TQFP variants and the larger SAM D20 pin counts - the 32-pin TQFP exposes fewer SERCOM and ADC channels than the 48/64-pin siblings. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving the engineer a faster path from selection to production.

見積もり お問い合わせ
ATSAMD20E15B-AUT - ARM Cortex-M0+ 48MHz 32KB Flash MCU | Microchip
ATSAMD20E15B-AUT

ATSAMD20E15B-AUT - ARM Cortex-M0+ 48MHz 32KB Flash MCU | Microchip

The Microchip ATSAMD20E15B-AUT is an ARM Cortex-M0+ based 32-bit microcontroller running at up to 48 MHz, integrating 32 KB of Flash and 4 KB of SRAM in a 32-pin TQFP (7x7 mm) package, qualified for industrial temperature range -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripheral interfaces (ADC, timers, communication buses) into one device. Microcontrollers sit at the heart of embedded systems, sitting below microprocessors in compute complexity but above simple logic ICs. Within the broader taxonomy: MCU -> 32-bit MCU -> ARM Cortex-M MCU -> Cortex-M0+ MCU -> low-power MCU -> SAM D20 family. The ATSAMD20E15B-AUT belongs to Microchip's SAM D20 family, designed for low-power, mixed-signal embedded designs. Key features include a 12-bit, up to 350 ksps ADC with up to 10 channels, a 10-bit 350 ksps DAC, six SERCOM channels configurable as UART/SPI/I2C, a 16-bit Timer/Counter, a Real-Time Clock, and full-speed USB 2.0 device support. The device operates from 1.62 V to 3.63 V, supports 48 MHz at 1.62-3.63 V in the -40C to +85C industrial range, and offers multiple low-power sleep modes with sub-microamp wake-up time. The on-chip SERCOM peripherals are highly reconfigurable, allowing one physical block to operate as either USART, SPI, or I2C - a design that minimizes pin count for varied interface requirements. The Cortex-M0+ core implements the ARMv6-M Thumb instruction set with a single-cycle I/O port for bit-banding, deterministic interrupt latency, and an optional Memory Protection Unit on equivalent family members. At 48 MHz, the core delivers 2.46 CoreMark/MHz, sufficient for sensor fusion, motor control loops, and simple protocol stacks. The integrated 32 KB Flash is rated for 10K erase/write cycles with retention; 4 KB SRAM supports most control-loop workloads. Typical applications include home automation controllers, consumer appliance interfaces, smart metering endpoints, IoT sensor nodes, industrial HMI panels, and low-power wireless sensor hub processors. The USB 2.0 full-speed device makes the part well suited to HID peripherals such as keyboards, mice, and custom HID-class tools. With AEC-Q100 variants available in the SAM D20 family, the same silicon architecture is also deployed in automotive body and chassis subsystems. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to each VDD pin and a bulk 4.7 uF capacitor on the main supply rail. Configure unused I/O pins as inputs with internal pull-up enabled to minimize quiescent current. For firmware development, Microchip's MPLAB X IDE with the XC32 compiler and Atmel Studio 7 both support the device, and SEGGER J-Link debug probes are fully compatible per SEGGER's supported device list. This page synthesizes distributor pricing across 9 channels, lists drop-in same-package alternatives from the SAM D20 family and competitor pin-compatible MCUs, and provides practical design notes that complement the manufacturer datasheet.

見積もり お問い合わせ
ATSAMD20E15B-MU - SAM D20E 32KB Flash Cortex-M0+ MCU | Microchip
ATSAMD20E15B-MU

ATSAMD20E15B-MU - SAM D20E 32KB Flash Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMD20E15B-MU is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D20E family, operating at up to 48 MHz with 32 KB of Flash and 4 KB of SRAM, packaged in a 32-pin VQFN (5x5 mm) with exposed thermal pad. It integrates a 12-bit ADC, a 10-bit DAC, a 256-channel Peripheral Touch Controller (PTC), an RTC, and six SERCOM communication interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, designed for deterministic embedded workloads. Within the power-management hierarchy, MCUs sit at the system-control tier above discrete logic and below application processors; they orchestrate sensors, user I/O, and low-bandwidth communications in battery-powered and industrial systems. The SAM D20 family is positioned by Microchip as the low-power entry point of the SAM Cortex-M lineup. Key features of the ATSAMD20E15B-MU include its 2.46 CoreMark/MHz performance, a single-cycle hardware multiplier, a SleepWalking peripheral event system, and an on-chip 32 kHz RTC oscillator with PLL-derived system clock. The device supports 1.62 V to 3.6 V supply operation, has a built-in brown-out detector, and provides up to 22 GPIO lines with peripheral multiplexing. Typical applications include home automation nodes, smart metering endpoints, consumer appliances, IoT sensor hubs, low-power wireless sensor platforms, and industrial control peripherals. The integrated PTC eliminates the need for an external touch-sensing IC in capacitive button, slider, and wheel designs. When designing with this part, observe the VQFN thermal pad soldering guidelines and ensure the SERCOM pin-mux is reviewed before PCB layout. Programming and debugging are supported through the SWD interface, requiring only two pins (SWDIO, SWDCLK) plus GND. This page consolidates distributor pricing, drop-in alternative ordering, and practical design notes for the ATSAMD20E15B-MU that are not collated in the manufacturer datasheet, including verified pin-compatible SAM D20 family members and recommended companion analog parts.

見積もり お問い合わせ