電源管理
サブカテゴリ
製品 (2819)
ADIN1300BCPZ-R7 - Gigabit Ethernet PHY, 10/100/1000 Mbps, 40-LFCSP | Analog Devices
The Analog Devices ADIN1300BCPZ-R7 is a low-power, single-port Gigabit Ethernet transceiver (PHY) supporting 10 Mbps, 100 Mbps, and 1 Gbps data rates in a 40-pin LFCSP-WQ (6x6 mm) package with wettable flanks. It delivers best-in-class latency under 290 ns (100 Mbps) and sub-400 ns (1000 Mbps) while consuming only 257 mW typical at 1 Gbps full duplex, designed specifically for industrial Ethernet, EtherCAT, PROFINET, and TSN applications. The device integrates an Energy Efficient Ethernet (EEE) physical layer, 802.3az support, automatic MDI/MDIX crossover, and on-chip termination resistors. An Ethernet PHY (physical layer transceiver) is the analog front-end in a layered network stack that converts between digital MAC-domain data and the differential analog signals on the twisted-pair cable. It sits below the MAC layer in the OSI model, handling line coding (PAM/PMA), link training, baseline wander correction, and signal equalization. Industrial PHYs such as the ADIN1300 are hardened against ESD, EMC, and temperature extremes, and they support deterministic latency demanded by real-time motion-control protocols. Key features of the ADIN1300 include 4 kV HBM ESD rating on MDI pins, integrated 1.25V LDO regulators, programmable RGMII/GMII/MII MAC interface, IEEE 1588 time-stamping support, and a configurable MDIO/MDC management interface. The 40-LFCSP-WQ package provides excellent thermal performance for fanless industrial designs and supports reflow soldering with its wettable flank terminations that enable automated optical inspection (AOI). The ADIN1300 uses a DSP-based echo canceller and baseline-wander correction loop, enabling robust 1000BASE-T operation over 100 m of CAT5e/6 cable even in electrically noisy industrial cabinets. The integrated PHY reduces BOM count versus MAC-plus-discrete-PHY designs and includes diagnostic features such as cable diagnostics, signal quality indicator (SQI), and loopback modes for factory test. Typical applications include industrial Ethernet switches, PLC communication modules, EtherCAT slave nodes, motion controllers, building automation gateways, and embedded IoT gateways requiring deterministic real-time networking. The wide -40C to +85C industrial temperature range supports outdoor and factory-floor deployment without additional thermal management. When designing with this device, ensure the MAC interface voltage matches the RGMII/GMII/MII logic level (1.8V, 2.5V, or 3.3V selectable via strapping resistors). Place the 25 MHz reference clock or crystal within 1 cm of the XI/XO pins to minimize jitter, and provide an isolated RJ45 magnetics module rated for 1 Gbps operation. Decouple each AVDD/DVDD pin with 100 nF plus 10 uF bulk capacitors to control power-supply noise coupling into the analog front-end. This page synthesizes distributor pricing, drop-in alternatives, and application guidance not consolidated on the manufacturer datasheet - useful for engineers sourcing the ADIN1300BCPZ-R7 for new designs or second-source qualification.
ADM1278-1ACPZ-RL - Hot Swap Controller + PMBus Monitor | ADI
The Analog Devices ADM1278-1ACPZ-RL is an integrated hot-swap controller and digital power-and-energy monitor with a PMBus-compatible interface, housed in a 32-pin LFCSP (5x5 mm) package. It targets 1.4 V to 20 V positive-rail hot-swap applications and integrates a 12-bit ADC for telemetry of VIN, VOUT, IOUT and on-die temperature. The device supports programmable current-limit thresholds from 5 mV to 25 mV across a sense resistor, with a 290 ns response time to short-circuit events. A hot-swap controller is a specialized power-management IC that sits between a live backplane and a removable circuit card, controlling the inrush current that flows when bulk load capacitance charges up. Without it, the charged capacitor looks like a momentary short, which can trip upstream supplies, cause connector arcing, or damage FETs. The ADM1278 combines that inrush-control role with on-board telemetry: a PMBus interface reports voltage, current, power and energy in real time so the system host can implement digital energy budgets, logging, and predictive analytics. Within the broader taxonomy, hot-swap controllers sit under hot-swap and ORing controllers -> power management ICs -> power management. Key features include constant-power folded-back current limiting for tighter FET SOA protection, programmable linear inrush current profile on power-up, FET-health monitoring with auto-shutdown on fault, and remote temperature sensing with programmable warning and shutdown thresholds. The integrated PMBus block supports readback of voltage, current, power and energy in a standard format readable by any supervisory MCU or BMC. The -1 suffix in the part number denotes the LFCSP package variant with specific pin assignments as described in the datasheet. Architecturally, the chip uses an external N-channel MOSFET as the high-side pass element, a high-side current-sense amplifier, a precision bandgap-referenced 12-bit ADC, and an I2C/SMBus-compatible PMBus interface block. The ADI datasheet (Rev. C) describes a constant-power foldback mode that derates the gate drive as VDS across the FET rises, holding the FET inside its thermal envelope during sustained fault events. Typical applications include server and datacenter hot-swap boards, network switches and routers with removable line cards, RAID/HBA cards, blade-server mezzanine cards, PCI Express add-in cards, and -48 V distribution systems with intermediate bus converters. Industrial applications requiring PMBus telemetry such as programmable DC supplies and remote radio units (RRUs) also benefit from the integrated monitoring. When designing with the ADM1278, choose the external MOSFET first - its SOA and RDSon drive efficiency, fault tolerance and thermal performance. The sense resistor value (RSENSE) directly sets the current-limit threshold, and a 1% tolerance part is strongly recommended for accurate telemetry. The PMBus address is resistor-programmable, allowing multiple hot-swap ICs to coexist on a single bus.
ADM705ARZ-REEL - 4.65V Microprocessor Supervisor | Analog Devices
The Analog Devices ADM705ARZ-REEL is a low-cost microprocessor supervisory circuit that monitors a 4.65V threshold and provides an active-low push-pull reset output, housed in an 8-pin SOIC (R-8) package and supplied on a 2500-piece tape-and-reel. It is designed for 5V power supply/battery monitoring in microprocessor-based systems and generates a reset during power-up, power-down, and brownout conditions. A microprocessor supervisor (also called a voltage supervisor or reset IC) is a power-management IC that watches the system supply rail and asserts a reset signal to the host processor whenever the rail falls below a preset threshold. This prevents code execution at unsafe voltages, which can lead to corrupted flash, latched peripherals, or indeterminate logic. Supervisors sit in the power-management IC hierarchy between simple voltage detectors and full PMICs, and are essential building blocks in any MCU/MPU-based design. Key features include a guaranteed valid RESET output with VCC as low as 1V, 190 µA typical quiescent current, a 200 ms reset pulse width, a 160 ms minimum reset timeout, and a debounced TTL/CMOS manual reset (MR) input. The reset output uses a push-pull totem-pole stage, eliminating the external pull-up resistor that open-drain alternatives require. The part is specified over the -40 °C to +85 °C industrial temperature range and ships in Pb-free/RoHS-compliant packaging. The ADM705 family shares its pinout across the ADM705/ADM706/ADM707/ADM708 series, allowing the designer to substitute parts to trade watchdog timing, or push-pull/open-drain output polarity, without re-laying-out the PCB. This drop-in compatibility, combined with low quiescent current and 1V-reset-valid operation, makes the ADM705 a long-standing industry staple for 5V supervisory designs. Typical applications include reset and supply monitoring for 8051, PIC, AVR, MSP430, and ARM Cortex-M microcontrollers, embedded industrial controllers, point-of-sale terminals, automotive body electronics, and battery-backed systems. The wide operating range and high noise immunity also suit it to noisy motor-control and SMPS post-regulation environments. When designing with this device, place the 1 µF bypass capacitor as close as possible to VCC and route MR with a short, debounced trace. Note that the ADM705 does not include a watchdog timer - choose the ADM706 if watchdog functionality is required.
ADP1031ACPZ-1 - Isolated PMU with 3 Regulators | Analog Devices
The ADP1031ACPZ-1 is a high performance, isolated micropower management unit (PMU) from Analog Devices that integrates an isolated flyback dc-to-dc regulator, an inverting dc-to-dc regulator, and a buck dc-to-dc regulator, providing three isolated power rails. It also includes four high speed serial peripheral interface (SPI) isolation channels, making it ideal for isolated data acquisition and industrial applications. The device is housed in a 41-lead LFCSP (9x7 mm) package and operates over a wide input voltage range. An isolated PMU is a power management IC that combines multiple power conversion stages with galvanic isolation, enabling safe and noise-free power transfer across an isolation barrier. It integrates the isolation components (such as transformers) and control circuitry into a single package, simplifying design and reducing board space. The ADP1031 belongs to the family of isolated power management units, which are essential in industrial automation, medical equipment, and communication systems where safety and noise immunity are critical. Key features of the ADP1031ACPZ-1 include a wide input voltage range, high efficiency, and integrated isolation. The flyback regulator provides a regulated output, while the inverting and buck regulators offer additional rails with different polarities and voltage levels. The device also features overvoltage protection (OVP) on the inverting regulator, which monitors the FB3 pin and stops switching if the voltage falls below VFB3 by 10%, ensuring safe operation. The integrated SPI isolation channels eliminate the need for external digital isolators, reducing component count and system cost. Technically, the ADP1031 uses a proprietary architecture that combines a primary-side controller with secondary-side regulation, achieving high efficiency and accurate output regulation. The device supports a wide range of output voltages and currents, making it versatile for various applications. The package is designed for excellent thermal performance, with an exposed pad for heat dissipation. Typical applications include isolated data acquisition systems, industrial process control, programmable logic controllers (PLCs), and isolated sensor interfaces. The device is particularly suited for applications requiring multiple isolated power rails and high-speed data isolation, such as motor drives and smart grid equipment. When designing with the ADP1031ACPZ-1, it is important to carefully select the external transformer and components to meet the required isolation and efficiency specifications. Proper PCB layout is essential to minimize noise and ensure reliable operation. The device also requires careful thermal management due to its power dissipation.
ADP1031ACPZ-2 - Isolated PMU with 7 Digital Isolators | Analog Devices
The ADP1031ACPZ-2 is a high performance, isolated micropower management unit (PMU) from Analog Devices that integrates an isolated flyback dc-to-dc regulator, an inverting dc-to-dc regulator, and a buck dc-to-dc regulator to provide three isolated power rails. Additionally, it contains four high-speed serial peripheral interface (SPI) digital isolator channels and three general-purpose digital isolator channels, totaling seven digital isolators. This device is designed for industrial applications requiring galvanic isolation and multiple isolated power domains. An isolated PMU is a power management IC that combines isolated DC-DC conversion with digital isolation in a single package, eliminating the need for separate isolated power supplies and digital isolators. It sits within the power management IC hierarchy, specifically under isolated power converters, and is essential for systems that require signal and power isolation for safety, noise immunity, or ground loop elimination. Key features of the ADP1031ACPZ-2 include a wide input voltage range, three isolated outputs (one flyback, one inverting, one buck), and seven digital isolator channels with data rates up to 100 kbps. The device operates over the industrial temperature range of -40°C to +125°C and is available in a 41-lead LFCSP (9x7 mm) package. The ADP1031ACPZ-2 variant specifically provides a 5.0V output on the buck regulator, as indicated by the '2' suffix. The ADP1031 uses a high-frequency flyback architecture with integrated power switches, achieving high efficiency and small form factor. The digital isolators use iCoupler technology, providing reliable isolation up to [DATA_NEEDED: isolation voltage] with low propagation delay. The device includes soft-start, overcurrent protection, and thermal shutdown for robust operation. Typical applications include industrial fieldbus systems, programmable logic controllers (PLCs), isolated sensor interfaces, and motor drive control circuits. The ADP1031ACPZ-2 is particularly suited for systems requiring isolated SPI communication and multiple isolated power rails, such as data acquisition systems and industrial automation. When designing with this device, ensure proper PCB layout for isolation barrier spacing and use recommended transformer and capacitor values from the datasheet. The input supply should be decoupled with low-ESR ceramic capacitors, and the isolated outputs should be filtered to meet ripple requirements.
ADP1031ACPZ-3-RL7 - Isolated PMU with 7 Digital Isolators | Analog Devices
The ADP1031ACPZ-3-RL7 is a high performance, isolated micropower management unit (PMU) from Analog Devices that integrates an isolated flyback dc-to-dc regulator, an inverting dc-to-dc regulator, and a buck dc-to-dc regulator to provide three isolated power rails. Additionally, it contains four high speed serial peripheral interface (SPI) digital isolators and three general-purpose digital isolators, making it a complete isolated power and data solution in a single 41-lead LFCSP (9x7 mm) package. This device is designed for applications requiring galvanic isolation and multiple regulated outputs, such as industrial process control, isolated data acquisition, and power supply monitoring. An isolated micropower management unit (PMU) is a power management IC that integrates multiple DC-DC converters and digital isolators to provide isolated power and signal transfer across an isolation barrier. It combines the functions of a flyback converter, an inverting converter, and a buck converter, along with digital isolators, into a single package. This integration reduces board space, simplifies design, and improves reliability compared to discrete solutions. The ADP1031 belongs to the family of isolated power management ICs, which are essential in systems requiring safety isolation, noise immunity, and multiple isolated supply rails. Key features of the ADP1031ACPZ-3-RL7 include a wide input voltage range, three isolated outputs (one positive, one negative, and one buck), and integrated digital isolators with up to 100 Mbps data rate. The device operates from a 4.5V to 60V input supply, making it suitable for industrial 24V buses and other high-voltage rails. The flyback regulator provides an isolated output up to 3.3V or 5V, the inverting regulator provides a negative output down to -5V, and the buck regulator provides a positive output down to 3.3V. The digital isolators provide reinforced isolation up to 5 kV rms, ensuring safe signal transfer across the isolation barrier. Technically, the ADP1031 uses a proprietary architecture that combines a primary-side flyback controller with secondary-side regulation, achieving high efficiency and low EMI. The device includes overvoltage protection (OVP) on the inverting regulator, which monitors the FB3 pin and stops switching if the voltage falls below VFB3 by 10%. This protects downstream circuitry from excessive negative voltages. The device also features soft-start, short-circuit protection, and thermal shutdown, ensuring robust operation in harsh environments. Typical applications include isolated data acquisition systems, industrial PLCs, motor control, and power monitoring. The ADP1031 is ideal for systems that require isolated power and data transfer, such as isolated SPI communication between a microcontroller and an ADC. Its integrated digital isolators eliminate the need for separate isolator ICs, reducing component count and board space. When designing with the ADP1031, ensure proper PCB layout with adequate spacing for isolation, and place decoupling capacitors close to the power pins. The device requires an external transformer for the flyback converter, and the selection of the transformer is critical for efficiency and isolation rating. Refer to the datasheet for recommended transformer specifications and layout guidelines.
ADP1048ARQZ-R7 - Digital PFC Controller, 400kHz, 24-QSOP | ADI
The Analog Devices ADP1048ARQZ-R7 is a digital power factor correction (PFC) controller with accurate AC power metering and inrush current control, housed in a 24-lead QSOP package. The device is specifically designed for interleaved and bridgeless PFC topologies in ac/dc systems, supporting switching frequencies from 30 kHz to 400 kHz with average current mode control. A Power Factor Correction controller is a specialized power management IC that shapes the input current drawn from the AC mains to be in phase with the input voltage, thereby maximizing the ratio of real power to apparent power. PFC controllers sit at the front end of ac/dc converters, between the input rectifier bridge and the bulk capacitor, and they form the first stage of the power supply hierarchy: PFC stage -> DC-DC converter -> point-of-load regulators -> powered loads. By maintaining a high power factor (typically > 0.99), PFC controllers reduce harmonic distortion, help systems meet regulatory standards such as IEC 61000-3-2, and improve overall energy efficiency in servers, telecom rectifiers, and industrial power supplies. Key features of the ADP1048ARQZ-R7 include programmable switching frequency up to 400 kHz, accurate AC power metering capability via an integrated digital engine, inrush current control to limit stress on the bulk capacitor during AC plug-in events, and a digital interface for parameter adjustment. The 24-lead QSOP package offers a compact footprint and supports surface-mount assembly with reflow soldering compatible with standard lead-free profiles. The digital PFC core implements a conventional boost topology with average current mode control, providing stable operation across a wide line and load range. The architecture combines a high-performance analog front end for current and voltage sensing with a digital controller that closes the PFC loop via a programmable algorithm. This digital approach enables per-design tuning without external component changes, simplifies BOM consolidation across product variants, and provides telemetry for input power, RMS current, RMS voltage, and power factor that the system host can read back through the I2C/PMBus-compatible interface. The ADP1048 is the interleaved/bridgeless sibling of the ADP1047, which targets single-phase PFC stages. Typical applications include high-efficiency ac/dc power supplies for servers and networking equipment, telecom rectifiers complying with 80 PLUS and ENERGY STAR programs, industrial SMPS front ends, UPS battery chargers, and interleaved/bridgeless PFC stages for 1 kW to 5 kW power ranges. When designing with the ADP1048ARQZ-R7, ensure the I2C address is correctly configured in the EEPROM and that the sense resistor in the inductor return path has sufficient bandwidth for the programmed switching frequency to maintain stable average-current control.
ADP225ACPZ - Dual 300mA Adj LDO, Low Noise, High PSRR | ADI
The Analog Devices ADP225ACPZ is a dual-channel, 300 mA adjustable-output, low-dropout (LDO) linear regulator in an 8-lead LFCSP-UD (2 mm × 2 mm) package. Each output rail can be set from 0.5 V to 5.0 V, and the part accepts input voltages from 2.5 V to 5.5 V with a typical dropout of 170 mV at 300 mA load. An LDO (low-dropout) linear regulator is a class of voltage regulator whose category (LM-IC) maintains a stable, accurate rail even when VIN approaches VLOOOW - i.e. the regulator continues to regulate with only a few hundred millivolts of headroom. In the broader power-tree hierarchy, an LDO sits downstream of switching DC-DC converters (which provide bulk step-down) and upstream of noise-sensitive loads; LDOs trade efficiency for clean output because no switching noise reaches the load. Key features include high power-supply rejection ratio (PSRR) for downstream ripple attenuation, low output noise suitable for RF and audio rails, integrated quick-output discharge (QOD) transistors that actively pull each output to ground when disabled, and stable operation with only 1 µF, ±30% ceramic output capacitors. The two channels are independently enabled and share a common input. The ADP225ACPZ is fabricated on a BiCMOS process that combines CMOS control logic with bipolar pass elements, achieving both low quiescent current and excellent transient response. The QOD MOSFETs prevent output voltage drift into the disabled state, which is critical for power-sequenced loads such as RF transceivers, FPGAs, and image sensors. Typical applications include portable and battery-powered devices (smartphones, wearables, tablets), wireless handsets and RF transceivers, image sensor and camera-module rails, FPGA/ASIC I/O and core supplies in low-voltage domains, and any space-constrained board that needs two clean rails from a single small package. When designing with this part, ensure the input supply has sufficient bulk capacitance to handle the simultaneous turn-on of both outputs and that the 1 µF minimum output capacitance requirement is met across temperature and DC bias. The exposed pad must be soldered to a sufficient copper pour for thermal dissipation.
ADP2360ACPZ-5.0-R7 - 60V, 50mA Synchronous Buck Regulator | Analog Devices
The Analog Devices ADP2360ACPZ-5.0-R7 is a high-efficiency, high-input-voltage, discontinuous-conduction-mode (DCM) synchronous step-down DC-to-DC switching regulator that delivers a fixed 5.0V output at up to 50mA continuous load current. Housed in an 8-lead LFCSP (Lead Frame Chip Scale Package) with an exposed pad, the device operates over a wide 4.5V to 60V input voltage range, making it ideal for regulating power from industrial 24V/48V rails, automotive batteries, and high-impedance loop sources in space-constrained applications. A buck (step-down) switching regulator is a DC-to-DC converter that uses an internal switch, an inductor, and a rectifier to transfer energy from input to output at a duty cycle that sets the output voltage below the input. Synchronous buck regulators replace the external Schottky rectifier with an internal low-side MOSFET, which improves efficiency at light loads and shrinks the bill of materials. The ADP2360 specifically uses a single-pulse pulse-frequency-modulation (PFM) architecture with adjustable peak-current control, minimizing both input and output ripple while allowing the designer to optimize efficiency for the application's operating conditions and minimize the compatible inductor size. Key features of the ADP2360ACPZ-5.0-R7 include a fixed 5.0V output (no external feedback resistors required), wide 4.5V to 60V input operating range, up to 50mA continuous output current, adjustable peak current limit via an external resistor, integrated P-channel high-side switch and N-channel low-side switch, internal soft-start, and a power-good (PG) output that indicates when VOUT is within regulation. The 8-pin LFCSP exposed-pad package provides a low thermal-resistance path and a compact footprint for industrial sensor modules, factory-automation nodes, and battery-powered remote transmitters. The PFM control topology is well suited to low-duty-cycle, light-load applications because it skips switching cycles when the output is in regulation, holding quiescent current to a minimum. A power-good flag simplifies interface to downstream microcontrollers and enables sequenced multi-rail power-up. The device is specified for operation from -40C to +125C junction temperature and is qualified for automotive and harsh-environment use cases. Typical applications include 4-20mA current-loop powered sensor transmitters, industrial process-control loops, automotive body and sensor electronics, battery-powered remote telemetry, and isolated low-power bias supplies. The high input-voltage tolerance allows direct connection to 24V industrial buses or 12V/24V automotive rails without pre-regulation. When designing with the ADP2360ACPZ-5.0-R7, choose the input capacitor, output capacitor, and inductor per the datasheet's selection tables to maintain stable DCM operation. A small ceramic input capacitor is typically sufficient because the PFM architecture draws input current only during the high-side switch on-time; the exposed pad must be soldered to a thermal land on the PCB for proper heat dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet alone.
ADP2360ACPZ-R7 - 60V 50mA Synchronous Step-Down DC-DC | Analog Devices
The Analog Devices ADP2360ACPZ-R7 is a high efficiency, high input voltage, synchronous step-down DC-DC switching regulator with 4.5V to 60V input range and 50 mA continuous output current capability, housed in an 8-pin LFCSP EP (exposed pad) package. Operating in discontinuous conduction mode (DCM), the ADP2360 is engineered for 4-20 mA industrial loop-powered applications and similar space-constrained designs where high input voltage and low quiescent current matter. A synchronous buck (step-down) DC-DC converter is a switching regulator topology that uses MOSFET switches to chop an input voltage and an LC filter to reconstruct a lower, well-regulated DC rail. DCM operation means the inductor current returns to zero each switching cycle, eliminating reverse-current losses and enabling high efficiency at light loads - a critical attribute when the source current itself is capped at a few milliampere. Key features include 60V maximum input voltage with built-in over-voltage protection, 4.5V minimum input for cold-start, an adjustable output from 0.8V to VIN, internal high-side and low-side synchronous MOSFETs, and 100 percent duty-cycle capability for low-dropout pass-through. The regulator requires only an inductor and small ceramic capacitors, simplifying BOM and shrinking the footprint. The architecture integrates a peak-current-mode controller with DCM boundary detection, a precision reference, and internal soft-start. The exposed pad (EP) of the LFCSP-8 package provides a low thermal resistance path (about 36 C/W) for the small 50 mA load it serves, ensuring reliable operation across -40C to +125C junction temperatures. Typical applications include 4-20 mA current-loop powered field transmitters, industrial sensors, smart meters, isolated industrial interface modules, low-power analog front-end bias rails, battery-powered industrial monitors, and remote telemetry nodes. The wide VIN tolerance also suits 24V, 36V, and 48V industrial buses. When designing with the ADP2360ACPZ-R7, size the inductor for the peak current boundary at your worst-case load and use low-ESR ceramic input/output capacitors to keep ripple below your analog front-end noise budget. The exposed pad must be soldered to a sufficiently large copper pour for proper thermal dissipation. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the standalone ADP2360 datasheet, giving engineers an actionable reference for sourcing and design-in.
ADP2370ACPZ-R7 - 800mA, 15V Buck DC-DC Converter | Analog Devices
The Analog Devices ADP2370ACPZ-R7 is a high efficiency, low quiescent current, 800 mA synchronous step-down (buck) DC-to-DC converter housed in an 8-lead, 3 mm x 3 mm LFCSP (QFN) exposed-pad package. It operates from a 3.2 V to 15 V input range, delivers an adjustable output from 0.8 V to 14 V, and uses a current-mode architecture with internal MOSFET switches that require only three tiny external components. The switching frequency is selectable between 600 kHz and 1.2 MHz via the FSEL pin, or it can be synchronized to an external 600 kHz to 1.2 MHz clock. A buck (step-down) DC-DC converter is a switching voltage regulator that uses an inductor, a switch, and a rectifier to convert a higher input voltage to a lower output voltage with high efficiency. The buck converter sits within the broader hierarchy of DC-DC converters -> switching regulators -> voltage regulators -> power management ICs -> semiconductors. By cycling the internal MOSFETs at high frequency and filtering with an LC network, a buck converter achieves efficiencies typically above 90 percent, vastly superior to linear regulators at large input-to-output voltage differentials. Key features of the ADP2370 include up to 800 mA of continuous output current, 92 percent peak efficiency at 1.2 MHz operation, low quiescent current for extended battery life, internal compensation, internal soft start, power-good output, and thermal shutdown. The device integrates high-side and low-side MOSFETs, eliminating the need for external switching transistors. Forced PWM (FPWM) mode maintains a constant switching frequency for noise-sensitive applications, while automatic PWM/PFM mode maximizes efficiency at light loads. The ADP2370 uses peak current-mode control with internal slope compensation, providing excellent line and load transient response across the full operating range. The internal reference is a high-accuracy bandgap with low temperature coefficient. Power-good indication, undervoltage lockout, and overcurrent protection are all integrated, reducing external component count to three (input capacitor, inductor, output capacitor). The exposed pad on the LFCSP-8 package provides a low thermal resistance path, enabling full 800 mA output even in compact designs. Typical applications include portable and battery-powered equipment, handheld instrumentation, point-of-load regulators for FPGAs, DSPs, and microcontrollers, automotive infotainment and telematics subsystems (non-safety-critical rails), industrial control boards, and distributed power systems. The wide 3.2 V to 15 V input range accommodates single-cell Li-ion, USB, 5 V and 12 V rails, making the device particularly versatile for mixed-rail designs. When designing with the ADP2370, select an inductor with low DCR to preserve efficiency and keep the input/output ceramic capacitors close to the IC to minimize parasitic inductance. For noise-sensitive analog loads, operate in FPWM mode to avoid PFM switching ripple; for battery-powered systems, leave PFM enabled to maximize efficiency at light load. The exposed pad must be soldered to a sufficient copper pour for thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Verified distributor data is current as of 2026-10-06, and all specifications come from the Analog Devices ADP2370/ADP2371 datasheet.
ADP31100001RZ - Dual 12V MOSFET Driver | onsemi
The onsemi ADP31100001RZ is a dual, nonisolated, high-side, bootstrapped 12 V N-channel MOSFET driver with output disable in an RZ package. It provides two independent driver channels for power-conversion switches and is identified by the full ordering code ADP31100001RZ. The verified source describes the device as the ADP3110 family member optimized for driving the two N-channel MOSFET switches used in a nonisolated synchronous converter. A MOSFET gate driver is an interface IC between a low-power control circuit and the gate of a power MOSFET. Its role in the power-management hierarchy is gate driver → interface driver → power-semiconductor controller, because it translates control signals into the higher voltage and current required to switch MOSFET gates rapidly and reliably. The ADP3110 supports efficient, high-performance power conversion while keeping the controller isolated from direct high-current gate-drive demands. The verified data identifies the device as a dual, high-voltage MOSFET driver with output disable. It is optimized for two N-channel MOSFETs and a 12 V drive application. A bootstrapped driver uses an internal voltage relationship to establish the required gate-drive voltage for a high-side switch, allowing the part to fit nonisolated synchronous power-converter architectures. The dual-channel arrangement reduces the number of separate driver ICs required when two complementary or similarly arranged switches must be controlled. The source snippets specifically classify ADP3110 as a power-management gate driver and identify it as a 2-channel, 12 V FET driver. One distributor listing also states that the architecture is suitable for industrial and automotive power-conversion systems, while another identifies the part under interface drivers, receivers, and transceivers. These classifications are consistent with a dedicated MOSFET-driver function but should not be treated as a substitute for the complete manufacturer datasheet. Typical applications include nonisolated synchronous DC-DC conversion, low- and intermediate-voltage power-supply stages, industrial control systems, and automotive power modules where two N-channel MOSFET switches are used. The output-disable feature can support system shutdown, fault isolation, or controlled turn-off, subject to the device’s exact electrical limits and timing requirements. Designers should verify the complete RZ pinout, supply limits, bootstrap-capacitor requirements, propagation delays, gate-drive ratings, and absolute maximum conditions against the onsemi datasheet before layout. Place the driver close to the power MOSFETs, keep gate loops short, provide a low-impedance supply return, and select external resistors and capacitors from the manufacturer’s recommended values. The listed distributor pages show current availability and purchasing references, but pricing and lead time should be confirmed at order time. This page consolidates the verified distributor identity, product classification, package ordering code, and practical gate-driver design context. It distinguishes confirmed facts from specifications that require the manufacturer datasheet, helping engineers evaluate ADP31100001RZ without treating aggregator data as a complete electrical specification.
ADP31100001RZ-AD - Dual 12 V MOSFET Driver | Analog Devices
The Analog Devices ADP31100001RZ-AD is a dual bootstrapped 12 V MOSFET driver with output disable, optimized for driving two N-channel MOSFET switches in a nonisolated synchronous application, and is supplied in the package identified as [DATA_NEEDED: exact package name]. The device provides two independent high-side and low-side drive functions for a 12 V power stage, with the verified data identifying it as a dual 12 V FET driver. The package type, pin count, pin names, exposed-pad details, and dimensions were not included in the supplied verified results and must be confirmed from the manufacturer datasheet before PCB layout or replacement approval. A MOSFET driver is an interface IC that converts a low-voltage control signal into the gate-drive voltages required by power MOSFETs. The driver category belongs to the interface-driver hierarchy, where a gate driver sits between a controller or digital logic and the switching devices in a power converter. The ADP3110 family is specifically described as a dual, high-voltage driver for two N-channel MOSFETs. Its bootstrapped architecture supports high-side and low-side operation in a nonisolated synchronous circuit, while the output-disable function provides a controlled way to inhibit switching outputs. The verified product data confirms the ADP3110 function, dual-channel architecture, N-channel MOSFET compatibility, 12 V application class, output-disable feature, and nonisolated synchronous use case. It does not provide verified numerical limits for propagation delay, peak gate current, quiescent current, supply range, UVLO thresholds, operating temperature, or electrical performance over temperature. Those values should not be inferred from the 12 V descriptor. Use the official ADP3110 datasheet and the exact ADP31100001RZ-AD ordering information for those parameters. Typical uses include 12 V synchronous power conversion, low- to intermediate-voltage buck or boost stages, MOSFET half-bridge control, and compact power modules where two N-channel switches are preferred. The output-disable pin can support fault handling or shutdown sequencing, while the dual driver reduces the number of discrete driver circuits required. The external MOSFETs still determine much of the switching performance, including voltage stress, current capability, gate charge, switching loss, and thermal behavior. The principal design consideration is exact pinout and package verification. The supplied search results identify ADP31100001RZ-AD with Analog Devices in some listings and onsemi in related ADP31100001RZ listings, but the requested MPN includes the Analog Devices ordering suffix. Confirm the manufacturer, datasheet, package drawing, exposed-pad requirements, and recommended land pattern before ordering. Do not assume that a similarly named ADP31100001RZ listing has identical manufacturer documentation. This page combines the verified distributor description, product-family function, application guidance, cross-reference status, and design cautions. Pricing and availability are presented only where the supplied search result provides a value, and all product specifications not explicitly present in the verified data remain marked for verification rather than being guessed.
ADP3159JRU-REEL7 - 4-Bit Programmable Buck Controller | Analog Devices
The Analog Devices ADP3159JRU-REEL7 is a 4-bit programmable synchronous buck controller optimized for converting a 5 V main supply into the core voltage required by high-performance processors. It uses N-channel external switches and provides programmable output voltage, active voltage positioning, and digital control through a 4-bit interface. The device is supplied in a 20-pin TSSOP surface-mount package. A synchronous buck controller is a DC-DC power-management device that controls external high-side and low-side switching transistors. The high-side device charges the output inductor during one switching interval, while the low-side device provides synchronous rectification during the complementary interval. This topology belongs to the switching-regulator and DC-DC-converter hierarchy and is widely used where processor rails require programmable voltage, high transient performance, and efficient power delivery. The ADP3159 family uses Analog Devices Optimal Positioning Technology, identified in the supplied results as ADOPT. Active voltage positioning adjusts the output response during load transitions to improve transient behavior and help meet demanding processor voltage specifications. The verified results describe four-bit digital programmability and a programmable 2.05 V output configuration, while the controller architecture is intended for low-voltage processor power rails. The ADP3159 is designed around a 5 V main supply, making it suitable for systems that distribute a common 5 V rail and then regulate it downward for processors, programmable logic, memory, and other digital loads. Its programmable control interface can support platform-level output-voltage configuration, reducing the need for fixed-voltage rails when a system requires multiple operating points. The controller approach also separates control from the power stage, allowing the external MOSFETs and inductor to be selected for the required current level. Typical applications include desktop and server processor cores, embedded computing modules, industrial controllers, communications equipment, and other systems requiring a controlled synchronous buck rail. The controller should be paired with external N-channel switching devices, inductor, input capacitors, output capacitors, and feedback or programming circuitry specified by the manufacturer datasheet. External power-stage component selection affects efficiency, transient response, ripple, thermal performance, and physical board area. Design attention should focus on the external MOSFET gate-drive path, inductor current capability, capacitor ESR and ripple rating, and layout separation of high-current switching nodes from sensitive feedback traces. The verified material identifies a TSSOP-20 package but does not provide complete electrical ratings, pin names, or a complete pinout table. Those values must be confirmed against the manufacturer datasheet before layout or replacement decisions are finalized. This product page consolidates the verified ADP3159 family function, package information, programming concept, and ADP3159JRU-REEL7 availability data. It is intended to support initial design review and sourcing; final schematic, compensation, thermal, and production qualification should rely on the current Analog Devices datasheet and application guidance.
ADP3169JRU-REEL - 2/3-Phase VRM Controller | Analog Devices
The Analog Devices ADP3169JRU-REEL is a 2/3-phase VRM9.0 controller for Intel processor power applications, packaged in a JRU package and supplied on tape-and-reel. The verified product listing identifies its primary function as a VRM9.0 2/3-phase controller for Intel platforms, but it does not provide the detailed electrical limits required to independently populate every performance field. [DATA_NEEDED: complete controller architecture details] What is a multiphase VRM controller? A multiphase voltage regulator module controller coordinates multiple power stages to deliver high-current, low-ripple rails to processors and other demanding digital loads. The ADP3169 is described in the supplied distributor data as a 2/3-phase solution for Intel VRM9.0 applications. Its role is control and sequencing rather than direct linear power conversion; external power devices typically perform the high-current switching function. The available listing supplies the key application identifier VRM9.0 and the phase configuration of 2/3 phases. Those details establish the component’s intended use in Intel-oriented processor power systems, although input-voltage range, output-voltage range, switching frequency, current-limit range, control method, and electrical timing are not supplied in the verified material. The package suffix JRU is retained exactly as listed, while the physical pin count and pin names are not provided in the source data. ADP3169JRU-REEL is intended for engineers designing or servicing boards that specifically call for a 2/3-phase Intel VRM9.0 controller. In such systems, controller compatibility depends on matching the external MOSFET selection, inductor design, sensing scheme, power sequencing, and PCB layout requirements. The tape-and-reel ordering suffix makes the part suitable for automated assembly, but it does not change the electrical function. A practical design constraint is that a distributor page may describe the device as a microcontroller or may provide only an abbreviated catalog description. Those labels should not be treated as a substitute for the manufacturer datasheet. Before layout release, verify the controller pinout, compensation method, current-limit behavior, gate-drive timing, auxiliary supplies, and recommended application circuit against the official technical documentation. This page consolidates the verified distributor description, current inventory references, ordering data, and design caveats for ADP3169JRU-REEL. It distinguishes known facts from parameters that require manufacturer documentation, helping buyers evaluate Intel VRM9.0 designs without inventing electrical specifications or assuming that every similarly described phase controller is pin-compatible.
ADP3335ARMZ-3.3 - 500mA anyCAP LDO, 3.3V Fixed | Analog Devices
The Analog Devices ADP3335ARMZ-3.3 is a 500 mA, 3.3 V fixed-output, high-accuracy anyCAP low-dropout (LDO) linear regulator housed in an 8-pin MSOP package. It operates from a 2.6 V to 12 V input rail and delivers up to 500 mA continuous load current with a typical dropout of 200 mV at full load, while achieving ±0.9% initial accuracy at 25°C and ±1.8% accuracy over line, load, and temperature. What is an LDO? An LDO (low-dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage, typically with a dropout of only a few hundred millivolts. LDOs belong to the broader category of linear regulators, which in turn sit under voltage regulators inside the power management IC hierarchy. Because they dissipate excess voltage as heat rather than switching it, LDOs introduce no switching noise, making them ideal for powering noise-sensitive analog and RF loads. The anyCAP architecture used by the ADP3335 family allows stable operation with any good-quality output capacitor - including low-ESR ceramic MLCC types - which simplifies board layout and shrinks the BOM in space-constrained designs. Key features include an ultralow quiescent current that extends battery life in portable equipment, an ultralow dropout of 200 mV at 500 mA, integrated thermal shutdown and current-limit protection, and a noise performance optimized for wireless and instrumentation applications. The device is specified over the extended -40°C to +85°C (junction to +150°C) operating range, suiting industrial environments. The ADP3335 uses an enhanced bipolar process and a precision bandgap reference that drives an internal PNP pass element. The anyCAP loop compensation removes the ESR-related stability constraints of legacy LDOs, allowing designers to use small 1 µF to 10 µF ceramic capacitors at the output without compromising phase margin. This combination of low noise, tight accuracy, and ceramic-cap stability is unusual for a 500 mA part and is a hallmark of the ADP33xx family. Typical applications include wireless handsets, notebook and palmtop computers, PCMCIA cards, barcode scanners, low-noise analog circuits, and battery-powered instrumentation requiring a clean 3.3 V rail. The wide 2.6 V–12 V input range also supports 5 V and 9 V system buses, and the low dropout margin permits one-cell Li-ion discharge down to ~3.5 V before regulation is lost. When designing with this part, place input and output capacitors as close to the IC as possible and ensure the PCB copper under the exposed pad (if present) provides adequate thermal relief - continuous 500 mA into a 5 V input from 12 V dissipates 4.35 W. The fixed -3.3 suffix means no external feedback resistors are required, reducing BOM cost and layout area versus adjustable LDOs.
ADR421BRZ - 2.5V Ultraprecision Low Noise Voltage Reference | Analog Devices
The Analog Devices ADR421BRZ is an ultraprecision, low-noise, 2.500 V XFET voltage reference IC delivering ±0.04% initial accuracy, 1.75 µV p-p noise (0.1 Hz to 10 Hz), and 3 ppm/°C maximum temperature coefficient in an 8-pin SOIC package (R-8). It provides up to 10 mA of source current from a 4.5 V to 18 V input supply, with 70 ppm/mA load regulation and 35 ppm/V line regulation. An XFET voltage reference is a specialized series-mode reference that uses an externally modulated JFET pair to generate a temperature-compensated bandgap-like voltage, achieving lower noise and better long-term stability than conventional buried-Zener references. It occupies the product hierarchy of voltage reference -> series reference -> precision reference -> power management IC, serving as the stable potential against which ADCs, DACs, and precision analog signal chains are calibrated. Key features include sub-2 µV p-p low-frequency noise, 50 ppm/1000 hrs long-term stability, 40 ppm typical hysteresis, and a wide 4.5 V to 18 V supply operating range with low quiescent current. The XFET architecture also eliminates the need for a resistor in series with the supply pin required by older Zener designs, simplifying PCB layout and improving turn-on settling. Architecturally, the XFET cell pairs a JFET reference transistor with a second JFET biased to cancel temperature drift. A precision op-amp servos the bandgap-like cell to maintain constant VOUT, while the trim network programs the initial accuracy. This topology trades the higher pre-trim noise of bandgap references for far better long-term drift and thermal hysteresis. Typical applications include precision 16-bit and 24-bit ADC and DAC reference inputs, industrial process control calibration, automatic test equipment (ATE) system references, and precision data acquisition systems in medical imaging, weighing scales, and 6.5-digit digital multimeters. The 2.5 V output makes it an ideal companion to devices such as the AD8628, AD8629, and ADI's AD57xx, AD76xx, and ADuM-series converter families. When designing with the ADR421BRZ, route the output node directly to the reference pin of the target converter with a 0.1 µF ceramic plus 1 µF tantalum bypass network within 5 mm of the reference pin to preserve noise and load regulation. Avoid running digital or switching traces under the reference - injected charge can deteriorate 0.1 Hz to 10 Hz noise performance. This page synthesizes distributor pricing across nine channels, parametric drop-in alternatives, and practical layout notes not consolidated on the manufacturer datasheet.
ADR421BRZ-REEL7 - 2.5V Ultraprecision XFET Voltage Reference | Analog Devices
The Analog Devices ADR421BRZ-REEL7 is an ultraprecision, low-noise 2.500 V XFET voltage reference IC delivering up to 10 mA output current in an 8-pin SOIC package, supplied on a 7-inch reel for high-volume SMT assembly. It features an initial accuracy of ±0.04% (B-grade), 3 ppm/°C temperature coefficient, 1.75 µV p-p noise (0.1 Hz to 10 Hz), and 50 ppm/1000-hour long-term stability, with an operating input range of 4.5 V to 18 V. A voltage reference is a precision circuit that produces a stable, known DC voltage independent of supply variations, temperature, and load current. Voltage references sit at the base of the signal chain in data acquisition, instrumentation, and precision analog systems: their absolute accuracy and noise floor set the ultimate performance limit of downstream ADCs, DACs, sensor bridges, and weighing scales. The ADR421 belongs to the XFET (eXtra implanted junction FET) family, which uses a junction FET reference cell rather than a buried Zener or bandgap to achieve sub-2 µV p-p noise and excellent thermal hysteresis of 40 ppm typical. Key features include 4.5 V to 18 V supply range, low supply current of 0.5 mA typical, line regulation of 35 ppm/V, load regulation of 70 ppm/mA, and -40 °C to +125 °C operating temperature. The SOIC-8 (R-8) package is the industry-standard precision reference footprint, allowing direct substitution on most reference layouts. Unlike buried-Zener references that need 10 V minimum, the XFET architecture operates from as low as 4.5 V, suiting it to 5 V and ±5 V or +5 V/-12 V system rails. The ADR421 is offered in three grades (A: ±0.05%, B: ±0.04%, C: ±0.12%) and three packages (8-lead SOIC, 8-lead MSOP, TO-92). Typical applications include precision data acquisition system references, high-resolution ADC and DAC reference inputs, industrial process control calibration, precision weighing scales, medical instrumentation, and instrumentation amplifiers. The 2.500 V output matches the full-scale range of many 16-bit and 24-bit sigma-delta ADCs (e.g., AD7799/AD7730 families) and is compatible with 5 V reference-input DACs. When designing with the ADR421, add a 0.1 µF ceramic bypass capacitor close to the supply pin and a 1 µF to 10 µF tantalum or ceramic capacitor on the output for stable load-transient response. The trim pin (pin 5) allows ±0.5% fine adjustment of the output using a 10 kΩ/1 kΩ divider; leave it open if trimming is not required. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone.
ADR4525BRZ-R7 - 2.5V Ultra-Low Noise Voltage Reference | Analog Devices
The ADR4525BRZ-R7 is a high precision, low power, low noise series voltage reference from Analog Devices, providing a fixed 2.5V output with ±0.02% maximum initial error (B grade). Housed in an 8-pin SOIC (SOIC-8) package, this device delivers up to 10 mA output current and operates over a wide supply range, making it ideal for precision data acquisition, industrial process control, and medical instrumentation. A voltage reference is a precision electronic component that produces a constant output voltage regardless of load, supply variations, or temperature. It serves as a stable benchmark for analog-to-digital converters (ADCs), digital-to-analog converters (DACs), and comparators, ensuring measurement accuracy. Voltage references are categorized into series and shunt types; the ADR4525 is a series reference, which offers lower power consumption and better accuracy than shunt references. Within the power management hierarchy, voltage references are essential building blocks in precision analog systems, bridging the gap between raw power supplies and the stable voltages required by sensitive circuitry. Key features of the ADR4525BRZ-R7 include ultra-low output noise (1.4 µV p-p typical from 0.1 Hz to 10 Hz), excellent temperature stability (2 ppm/°C typical), and a low dropout voltage. The device also features a wide operating temperature range of -40°C to +125°C, making it suitable for harsh environments. Its high accuracy and low noise are achieved through an innovative core topology that minimizes thermal and noise errors. Technically, the ADR4525 uses a bandgap-based architecture with precision laser-trimmed resistors to achieve its tight initial accuracy. The output is buffered to provide low output impedance and fast transient response. The device is fully specified over the industrial temperature range and is available in tape and reel packaging (R7 suffix) for automated assembly. Typical applications include precision data acquisition systems, high-resolution ADCs and DACs, industrial process control, medical devices, and portable instrumentation. The low noise and high accuracy make it particularly well-suited for reference buffering in 16-bit and higher resolution converters. When designing with the ADR4525BRZ-R7, ensure adequate decoupling on the input and output pins with 0.1 µF and 1 µF capacitors, respectively, to maintain stability and minimize noise. The output can source up to 10 mA, but for higher current loads, an external buffer is recommended.
ADT7475ARQZ-REEL - 4-Fan PWM Thermal Controller | onsemi
The onsemi ADT7475ARQZ-REEL is a dBCool remote thermal monitor and four-fan PWM controller designed for active cooling in noise-sensitive or power-sensitive equipment. The verified distributor listing specifies a -40°C to 125°C temperature-monitor range, internal and external sensor support, SMBus output, and a 16-QSOP package. Its core role is to combine thermal monitoring with closed-loop fan control rather than relying on fixed-speed cooling. A remote thermal monitor and fan controller is a power-management and thermal-management IC that measures temperature and regulates cooling equipment according to configured thresholds. In the hierarchy, it belongs to system monitoring and fan-control ICs, which sit below broader thermal-management and power-management systems. The ADT7475 supports one on-chip temperature sensor and two remote temperature-sensor diode channels, enabling distributed temperature measurement in a compact controller. Key verified features include control and monitoring for up to four fans, high- and low-frequency fan-drive signals, an SMBus output, and an extended temperature-measurement range extending to 191°C as stated in indexed descriptions of the manufacturer datasheet. These features allow designers to combine local package-temperature protection with remote-diode monitoring while using variable-speed fans to reduce acoustic noise and power consumption. The controller measures and controls fan speed for thermal regulation, making it applicable to computer servers, storage systems, communications equipment, industrial controllers, and other multi-fan platforms. Its internal sensor and remote-diode inputs can support different thermal zones, while PWM output enables gradual fan-speed changes instead of abrupt full-speed operation. The 16-QSOP surface-mount package is suitable for compact production boards. A key design consideration is validating remote-diode electrical characteristics, sensor placement, fan-drive polarity, and SMBus configuration against the manufacturer datasheet. Because the provided search data does not expose exact timing, voltage, current, resolution, or absolute-maximum values for every parameter, those details are marked as needed rather than inferred. This page combines verified distributor facts, official-datasheet findings, and explicit engineering data gaps. Unlike a simple fan switch, the ADT7475ARQZ-REEL adds active temperature feedback and programmable fan-speed control, helping systems balance thermal margin against fan noise and power. This synthesis is intended to support component selection, schematic planning, and qualified drop-in replacement research.
ADUM3190ARWZ - 2.5kV Isolated Error Amplifier | Analog Devices
The ADUM3190ARWZ is a high-stability isolated error amplifier from Analog Devices, designed for isolated voltage feedback in power supplies. It integrates a precision reference and an error amplifier with an isolated output, providing a 2.5 kV RMS isolation rating. The device operates from a single 3.0 V to 20 V supply on the primary side and features a 400 mV reference with ±1% accuracy. It is available in a 16-lead SOIC-W package, making it suitable for space-constrained designs. An isolated error amplifier is a specialized analog IC that transfers an error signal across an isolation barrier without using an optocoupler. It typically includes a precision reference, an error amplifier, and an isolation channel (often based on iCoupler technology) to provide a feedback signal that is galvanically isolated from the output. This component is essential in isolated DC-DC converters and switching power supplies where the feedback path must cross the isolation boundary while maintaining accuracy and stability. Key features of the ADUM3190ARWZ include a 2.5 kV RMS isolation rating, a 400 mV reference with ±1% accuracy, and a wide operating temperature range of -40°C to +125°C. The device offers a typical gain bandwidth of 400 kHz and a quiescent current of 1.2 mA, enabling efficient operation in power management circuits. Its high stability ensures reliable performance over temperature and time, making it ideal for industrial and automotive power systems. Technically, the ADUM3190ARWZ uses Analog Devices' iCoupler technology to achieve isolation, which provides superior performance compared to optocoupler-based solutions, including better temperature stability and longer lifespan. The error amplifier has a transconductance output that can be compensated with external components to optimize loop stability. The device also includes an internal reference that can be used for voltage regulation, simplifying the external circuit. Typical applications include isolated DC-DC converters, offline power supplies, and isolated voltage sensing in motor drives and battery management systems. The device is particularly suited for applications requiring precise voltage regulation across an isolation barrier, such as telecom and server power supplies. When designing with the ADUM3190ARWZ, ensure proper PCB layout to maintain isolation creepage and clearance distances. The feedback loop compensation should be designed according to the datasheet guidelines to achieve stable operation. The device is RoHS compliant and available in tape and reel packaging.
ADUM3191ARWZ - Isolated Error Amplifier | Analog Devices
The ADUM3191ARWZ is an isolated error amplifier from Analog Devices, designed for feedback control in isolated power supplies. It integrates a precision error amplifier with an isolated PWM signal path, providing a compact solution for voltage regulation across an isolation barrier. The device operates from a single 3.0V to 20V supply and features a 400mV reference, making it suitable for a wide range of industrial and automotive applications. An isolated error amplifier is a specialized analog IC that amplifies the difference between a feedback voltage and a reference, then transmits the error signal across an isolation barrier without a direct electrical connection. This is essential in isolated power converters where the primary and secondary sides must be galvanically isolated for safety and noise immunity. The ADUM3191ARWZ uses Analog Devices' iCoupler technology to achieve this isolation, eliminating the need for optocouplers and their associated aging and nonlinearity issues. Key features of the ADUM3191ARWZ include a 2.5kVrms isolation rating, a 400mV reference with ±1% accuracy, and a bandwidth of 200kHz. The device supports an input voltage range of 3.0V to 20V and operates over the industrial temperature range of -40°C to +125°C. The SOIC-8 package is compact and industry-standard, facilitating easy integration into existing designs. The ADUM3191ARWZ is built on Analog Devices' proprietary iCoupler technology, which uses chip-scale transformers to transmit signals across the isolation barrier. This approach provides superior performance compared to optocouplers, including higher reliability, faster response, and better temperature stability. The device also includes an internal compensation network, simplifying the external circuit design. Typical applications include isolated DC-DC converters, offline power supplies, and motor drives. In these systems, the ADUM3191ARWZ provides accurate voltage feedback while maintaining galvanic isolation, improving system safety and performance. Its high bandwidth and low propagation delay make it suitable for high-frequency switching converters. When designing with the ADUM3191ARWZ, ensure proper PCB layout to maintain isolation creepage and clearance distances. The device requires a bypass capacitor on the primary side and careful attention to the feedback loop compensation to ensure stability.
ADUM3220ARZ - 4A Dual-Channel Isolated Gate Driver | Analog Devices
The ADUM3220ARZ is a 4 A dual-channel isolated gate driver from Analog Devices, based on the proprietary iCoupler technology. It combines high-speed CMOS and monolithic transformer isolation to provide robust, isolated drive for power transistors such as MOSFETs and IGBTs. The device is housed in an 8-lead SOIC package (8-SOIC, 0.154" width) and offers a 2500 Vrms isolation rating, making it suitable for applications requiring galvanic isolation between control and power stages. Isolated gate drivers are essential components in power electronics systems where the control circuitry must be electrically isolated from the high-voltage power stage. They transmit switching signals across an isolation barrier while providing sufficient drive current to charge and discharge the gate capacitance of power switches. The ADUM3220ARZ integrates the isolation and driver functions in a single IC, eliminating the need for external pulse transformers and simplifying PCB design. Key features of the ADUM3220ARZ include a 4 A peak output current, precise timing with a maximum propagation delay of 60 ns, and channel-to-channel matching of 5 ns. It operates over a wide supply voltage range and supports high junction temperatures up to 125°C. The device is RoHS compliant and lead-free, meeting modern environmental standards. The ADUM3220ARZ uses iCoupler technology, which employs chip-scale transformers to achieve isolation. This approach offers superior performance compared to optocouplers, including higher data rates, lower power consumption, and better timing accuracy. The driver's output stages are designed to deliver high peak current for fast switching, reducing switching losses in power converters. Typical applications include isolated switch-mode power supplies, motor drives, solar inverters, and industrial automation systems. The ADUM3220ARZ is particularly well-suited for driving IGBTs and MOSFETs in half-bridge or full-bridge configurations, where its dual-channel architecture and precise timing ensure reliable operation. When designing with the ADUM3220ARZ, it is important to provide adequate decoupling on the input and output supplies and to minimize parasitic inductance in the gate drive loop. Proper PCB layout is critical to achieve the specified timing and isolation performance.
ADUM3220ARZ-RL7 - Isolated 4A Dual Gate Driver | Analog Devices
The ADUM3220ARZ-RL7 is a dual-channel, isolated gate driver from Analog Devices, delivering 4 A peak output current per channel. It is based on the proprietary iCoupler technology, which combines high-speed CMOS and monolithic transformer isolation to provide reliable galvanic isolation up to 2500 Vrms. The device is housed in a compact 8-SOIC package (0.154", 3.90mm width), making it suitable for space-constrained power conversion designs. An isolated gate driver is a specialized integrated circuit that amplifies control signals from a low-voltage controller to drive power transistors (such as MOSFETs and IGBTs) while providing electrical isolation between the control side and the power stage. This isolation protects sensitive logic circuits from high-voltage transients and ground loops, which is essential in applications like motor drives, switch-mode power supplies, and solar inverters. The ADUM3220ARZ-RL7 belongs to the family of digital isolators and gate drivers, sitting between simple level shifters and more complex isolated power supplies. Key features of the ADUM3220ARZ-RL7 include a 4 A peak output current, a maximum propagation delay of 60 ns, and a channel-to-channel matching of 5 ns. These precise timing characteristics ensure synchronized switching of power devices, reducing switching losses and electromagnetic interference. The device also supports high junction temperature operation, making it robust for industrial environments. Its 2500 Vrms isolation rating meets the requirements of many safety standards, and it is RoHS compliant and lead-free. From a technical perspective, the ADUM3220ARZ-RL7 uses a monolithic transformer to couple signals across the isolation barrier, offering superior performance compared to optocouplers in terms of speed, reliability, and power consumption. The driver features a nominal UVLO (undervoltage lockout) of 4.1 V, ensuring that the output stage is fully enabled only when the supply voltage is adequate. This prevents erratic behavior during power-up and brownout conditions. The dual-channel configuration allows driving both high-side and low-side switches in a half-bridge topology with a single device. Typical applications include isolated DC-DC converters, motor control inverters, and power supplies for industrial and automotive systems. The ADUM3220ARZ-RL7 is particularly well-suited for applications requiring high-speed switching and robust isolation, such as server power supplies and renewable energy inverters. When designing with this device, it is important to provide adequate decoupling on the input and output supplies and to follow the recommended layout guidelines to minimize parasitic inductance. The propagation delay and matching specifications should be considered when designing dead-time for half-bridge circuits to prevent shoot-through current.