BTS3028SDRATMA1 vs BTG70902EPLXUMA1 比較
詳細な並列比較: BTS3028SDRATMA1 メーカー: Infineon および BTG70902EPLXUMA1 メーカー: Infineon。主要仕様、電気的特性、パッケージ、ライフサイクルステータス、価格、在庫状況を比較して、設計要件に最適な部品を判断してください。
Infineon
BTG70902EPLXUMA1 - 2A PROFET+2 12V Smart High-Side Switch | Infineon
BTG70902EPLXUMA1 ✓ 生産中仕様比較
| パラメータ | BTS3028SDRATMA1 | BTG70902EPLXUMA1 |
|---|---|---|
| ブランド | Infineon | Infineon |
| カテゴリ | Power MOSFET Drivers | Power MOSFET Drivers |
| ライフサイクル状態 | 有効 | 有効 |
| 在庫状況 | In Stock | In Stock |
| 単価（USD） | $0.92 | $0.99 |
| Product Type | Smart Low-Side Power Switch | — |
| トポロジー | 1:1 N-Channel, single channel | — |
| 出力電流（最大） | 5 A | — |
| On-Resistance RDS(ON) | 28 mΩ (typ.) | — |
| Load Voltage (max) | 60 V (load-dump rated) | — |
| 動作電源電圧 | 5 V to 28 V (typ. 13.5 V) | — |
| Logic Input Voltage (IN) | Logic-level, 3.3 V/5 V compatible | — |
| パッケージ | PG-TO252-3-11 (DPAK, 3 pins = 2 leads + tab) | PG-TSDSO-14 (exposed pad) |
| 実装タイプ | Surface Mount | Surface Mount |
| 動作温度 | -40 °C to +150 °C (junction) | — |
| Protection Features | Overtemperature shutdown, overvoltage clamp, ESD, short-circuit current limit, reverse battery, ground loss | Overcurrent, Short-Circuit, Over-Temperature (latch), Over-Voltage, Under-Voltage Lockout, Reverse Battery |
| Status Output | Open-drain diagnostic flag | — |
| Automotive Qualification | AEC-Q100 | AEC-Q100 (PROFET+2 family targeted at automotive) |
| RoHS ステータス | Compliant | Compliant |
| MSLレベル | [DATA_NEEDED: MSL rating] | [DATA_NEEDED: MSL rating per JEDEC J-STD-020] |
| Product Family | — | PROFET+2 12V |
| 機能 | — | Smart High-Side Power Switch |
| Number of Channels | — | 1 |
| Input-to-Output Ratio | — | 1:1 |
| 出力構成 | — | N-Channel High-Side |
| Continuous Load Current | — | 2 A |
| Nominal Operating Voltage | — | 12 V (automotive bus) |
| Operating Voltage Range | — | [DATA_NEEDED: Vbb operating range min/max] |
| On-State Resistance (Ron) | — | [DATA_NEEDED: Rdson typ/max in mohm] |
| 電流制限 | — | Fixed (value not specified in retrieved data) |
| Diagnostic Output | — | DEN pin (current sense / fault flag) |
| Enable Input | — | IN pin (active-high) |
| Channel Select | — | DSEL pin |
| Slew Rate Control | — | Yes (internal, for EMI) |
| 動作接合温度 | — | -40 C to +150 C |