AD977AARS - 16-Bit 200kSPS Serial ADC | Analog Devices
部品番号: AD977AARS ✓ 生産中AD977AARS 概要
An ADC is an interface IC that converts an analog input voltage into a digital code for processing by a microcontroller, DSP, FPGA, or other digital system. In the hierarchy of electronic components, the AD977AARS belongs to the ADC/DAC class, then to the analog-to-digital converter and successive-approximation converter families. Its serial interface reduces the number of signal traces required compared with a parallel ADC, while the 200 kSPS conversion rate supports acquisition rates that are substantially above general-purpose low-speed measurement devices.
The AD977A provides 16-bit resolution, a 200 kSPS throughput rate, and operation from one 5 V supply. Its successive-approximation architecture performs conversion through a sequence of comparisons, combining a deterministic conversion process with low power consumption for a single-supply device. The 28-lead SSOP package uses a 0.65 mm lead pitch and is designed for surface-mount assembly, allowing the converter to be placed on conventional high-density analog and mixed-signal circuit boards.
AD977AARS is identified as a one-input ADC with one SAR conversion core, although the product listings also characterize the associated family as a multichannel converter. Designers should use the pin-description table and analog input configuration in the manufacturer datasheet when assigning channels, references, and digital control signals. The product-page summary distinguishes AD977A from the base AD977 through throughput rate: the AD977A reaches 200 kSPS, while the base AD977 reaches 100 kSPS.
Typical uses include process-control and factory data acquisition, communications receivers, measurement instruments, digital diagnostics, and embedded systems that require accurate serial conversion. The 5 V supply and serial output make the device suitable for designs where a dedicated parallel ADC bus would increase routing complexity. In signal-chain layouts, input and reference grounding remain as important as converter selection because they determine the repeatability of the sampled code.
PCB implementation should follow the pin assignments and layout guidance in the manufacturer datasheet. Keep analog input and reference traces short, maintain a continuous ground reference, and place required bypass capacitance close to the supply pins. Because the converter uses a single 5 V rail, supply decoupling and clock or serial-interface timing should be checked together during signal-integrity and power-integrity reviews.
This product page combines the manufacturer family specifications with practical selection guidance, verified package characteristics, sourcing instructions, and clearly qualified drop-in alternatives. It distinguishes electrically equivalent grade or lead-free ordering options from speculative cross-package substitutes so engineers can assess replacement risk without redesigning an existing 28-pin SSOP footprint.
ドロップイン代替品: AD977AARS — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: AD977AARS (同一形状・フットプリント) — 相違点: Package, Supply Voltage, Conversion Architecture, Power-Down Mode, Throughput Rate.
AD977ABRS
✅ ドロップイン価格はお問い合わせください
データシートを見る →AD977AARSZ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD977AARS 最大定格&電気的特性
| Converter Type | 16-bit successive-approximation ADC |
| 分解能 | 16 bit |
| Throughput Rate | 200 kSPS |
| 電源電圧 | 5 V |
| Supply Type | Single supply |
| Input Count | 1 input |
| Conversion Architecture | Successive approximation |
| Digital Interface | Serial I/O |
| Channel Count | 3 channels |
| パッケージ | 28-pin SSOP |
| Package Type | PDSO28 |
| Lead Pitch | 0.65 mm |
| Package Width | 5.30 mm |
| 実装タイプ | Surface mount |
| Process Technology | BiCMOS |
AD977AARS 5.30 mm ピン配置ガイド
AD977AARS (5.30 mm パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD977AARS.
詳細は データシート をご参照ください。
主な用途
AD977AARS の用途: 6 件s: Industrial Process Measurement, Communications Receiver, Precision Data-Acquisition System, Test and Measurement Instrument, Embedded Control System, Digital Diagnostics.
Industrial Process Measurement
The AD977AARS fits industrial process-measurement loops that require 16-bit resolution, a 200 kSPS sampling rate, and serial data transfer. Place the converter at the output of a conditioned sensor or instrumentation amplifier, then connect its serial interface to a microcontroller or industrial controller. The single 5 V supply simplifies analog-system power planning, while the SSOP package preserves board area. Because each conversion requires settling of the external front end, the input filter and acquisition cycle must be designed together rather than treating the 200 kSPS figure as an unlimited system sampling rate.
おすすめ
Communications Receiver
AD977AARS is suitable for communications receivers in which analog waveform data must be converted into a compact digital stream. Its 16-bit nominal resolution provides 65,536 nominal code levels, and the 200 kSPS throughput provides substantially faster conversion than the 100 kSPS base AD977. Use the serial output to reduce interface width on compact receiver boards. The 5 V supply and 28-pin SSOP outline support space-constrained implementations, provided that routing from the RF or baseband front end to the converter preserves signal integrity and common-mode limits remain within the family specifications.
おすすめ
Precision Data-Acquisition System
The AD977AARS can serve as the sampling element of a precision data-acquisition system requiring 16-bit data and a 200 kSPS conversion rate. Its serial interface leaves more PCB area available for input conditioning, isolation, and digital processing than a parallel ADC of comparable resolution. The single 5 V operating supply simplifies analog rail integration. For best results, match the converter's input range to the conditioned analog signal, use a low-noise reference, and schedule conversion start and data acquisition so the front end has sufficient acquisition time at each 200 kSPS operating point.
おすすめ
Test and Measurement Instrument
AD977AARS is appropriate for compact measurement instruments that digitize slowly changing or repetitive analog signals and require more resolution than a low-speed sensor ADC. A 16-bit SAR converter provides a direct digital representation for calibration, waveform inspection, or automated test. The 200 kSPS rate allows acquisition of faster events than the 100 kSPS base AD977 while retaining a straightforward serial interface. The main design consideration is signal conditioning: keep source impedance balanced, provide suitable reference decoupling, and verify that the analog input remains inside the converter's specified range under worst-case conditions.
おすすめ
Embedded Control System
The AD977AARS works well as an ADC front end for an embedded controller monitoring analog plant variables. It converts an analog input at up to 200 kSPS and transfers the result through its serial interface to a microcontroller or digital signal controller. The 16-bit code width supports fine-grained measurements, while the 28-pin SSOP package reduces routing demand compared with a parallel conversion interface. In a control loop, conversion latency, filtering, and the timing of control updates should be evaluated together. The external analog front end must present a valid settled signal at the conversion instant.
おすすめ
Digital Diagnostics
AD977AARS can digitize diagnostic waveforms in medical, laboratory, and equipment-monitoring systems where 16-bit resolution and deterministic successive-approximation conversion are useful. The 200 kSPS throughput allows repetitive pulse or waveform sampling, and the serial interface supports connection to a digital processor with fewer traces than a parallel ADC. The 5 V supply is straightforward to integrate, but safety-critical use requires additional review of the exact device grade, isolation architecture, reference integrity, and applicable medical or sector-specific requirements. The converter should not be treated as a complete diagnostic front end without suitable sensing, conditioning, and protection.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: AD977AARS — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD977ABRS | AD977AARSZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Converter Type | 16-bit successive-approximation ADC | 16-bit AD977A-family ADC | 16-bit successive-approximation ADC |
| Resolution | 16 bit | 16 bit | 16 bit |
| Throughput Rate | 200 kSPS | 200 kSPS family rate | 200 kSPS |
| Supply Voltage | 5 V single supply | 5 V single supply | 5 V single supply |
| Digital Interface | Serial I/O | Serial I/O | Serial I/O |
| Process Technology | BiCMOS | BiCMOS family construction | BiCMOS |
| Ordering-Suffix Difference | AARS grade and 28-lead SSOP designation | ABRS grade designation; 0 kSPS stated throughput difference | Adds Z lead-free designation; 0% stated difference in resolution and throughput rate |
主な差別化要因
- Higher conversion throughput within the AD977 family (vs Base AD977)
- Single-supply integration simplifies analog power planning (vs Dual-supply ADC designs)
- Compact serial-interface implementation (vs 16-bit parallel-interface ADC designs)
設計ノート
Use the AD977A family pin table and package drawing to assign the 28 leads. Place the required 5 V bypass capacitors close to the supply and ground pins, keep analog input and reference traces short, and maintain a continuous ground plane beneath the converter where the package and board stackup permit. The SSOP has a 0.65 mm lead pitch, so assembly clearance and solder-joint inspection deserve attention on high-density boards.
Treat the analog input, voltage reference, and serial clock as related high-impedance or timing-sensitive nodes. Keep the input source impedance and acquisition network compatible with the 16-bit SAR conversion process, and route serial clock and data away from sensitive analog traces. Confirm that the external front end has settled before each conversion start, particularly when operating near the 200 kSPS maximum throughput.
Do not confuse the AD977A with the base AD977 solely because both use the same family name: the AD977A supports 200 kSPS, while the base AD977 is listed at 100 kSPS. Also verify the grade and temperature requirements when moving from AD977AARS to AD977ABRS or AD977AARSZ. A shared 28-pin SSOP footprint does not by itself establish equivalence for every environmental requirement.
コンプライアンス情報
The standard AD977AARS suffix and the separate AD977AARSZ lead-free ordering option are listed, but explicit compliance declarations are not included in the product summaries.