ADF4159CCPZ-RL7 - 13 GHz Fractional-N PLL | Analog Devices
部品番号: ADF4159CCPZ-RL7 ✓ 生産中ADF4159CCPZ-RL7 概要
A fractional-N frequency synthesizer is a clock and timing IC that generates a programmable output frequency from a stable reference. It belongs to the broader sequence of PLL-based frequency synthesizer, clock and timing IC, and semiconductor categories. The fractional-N architecture allows fine frequency spacing without requiring an impractically high reference frequency, making the device useful where precise tuning and rapid phase-lock acquisition are both important.
Principal features include direct modulation, fast waveform generation, slow waveform generation, and a 25-bit fractional-N modulus. The 13 GHz maximum operating frequency supports microwave and RF signal chains, while sub-hertz resolution permits fine channel selection. The low-noise digital phase-frequency detector, precision charge pump, and programmable reference divider provide the core loop functions, although exact divider ratios, lock-time curves, and phase-noise values should be selected from the manufacturer datasheet for the intended reference and loop design.
The ADF4159 architecture combines frequency synthesis with programmable waveform generation to support applications requiring both a synthesized carrier and modulation control. Direct modulation can reduce system complexity by superimposing control information onto the generated output without requiring a separate modulation path in every design. The exact modulation bandwidth, output power, and spur performance remain dependent on reference quality, loop filter design, device settings, and board implementation.
Typical uses include microwave test and measurement, RF signal generators, communications test equipment, frequency conversion systems, and local-oscillator generation. It is also appropriate for laboratory and industrial instrumentation where programmable RF output, fine resolution, and fast acquisition are more important than minimum unit cost. The exposed-pad LFCSP construction supports compact layouts, although careful thermal and return-path design is required.
When laying out the circuit, follow the manufacturer datasheet when assigning pins, selecting loop-filter components, placing decoupling capacitors, and routing the RF and reference paths. Keep the reference and RF connections short, maintain a controlled ground return around the exposed pad, and verify lock behavior across temperature, supply voltage, and output-frequency ranges before production.
This page combines the ADF4159 architecture, package details, replacement comparisons, application guidance, and practical design considerations in one engineering-focused reference. It also highlights where pin-compatible alternatives differ in operating range or qualification so that replacements can be evaluated without overlooking functional constraints.
ドロップイン代替品: ADF4159CCPZ-RL7 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ADF4159CCPZ-RL7 (同一形状・フットプリント) — 相違点: Package, Frequency Resolution, Maximum Output Frequency, Product Type.
ADF4159WCCPZ-RL7
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADF4169CCPZ-RL7
✅ ドロップイン価格はお問い合わせください
データシートを見る →ADF4169WCCPZ-RL7
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADF4159CCPZ
✅ ドロップイン価格はお問い合わせください
データシートを見る →ADF4159CCPZ-RL7 仕様
| Device Type | Fractional-N frequency synthesizer and PLL |
| Maximum RF Input Frequency | 13 GHz |
| Minimum RF Input Frequency | 500 MHz |
| Maximum Output Frequency | 2 GHz |
| Fractional-N Fixed Modulus | 25 bit |
| Frequency Resolution | Sub-hertz |
| Modulation Capability | Direct modulation |
| Waveform Generation | Fast and slow waveform generation |
| Phase Detector | Low-noise digital phase-frequency detector |
| Charge Pump | Precision charge pump |
| Reference Divider | Programmable |
| パッケージ | 24-lead LFCSP with exposed pad |
| Package Code | CP-24 |
| Shipping Format | Tape and reel |
ADF4159CCPZ-RL7 cp-24 ピン配置ガイド
ADF4159CCPZ-RL7 (cp-24 パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ADF4159CCPZ-RL7.
詳細は データシート をご参照ください。
主な用途
ADF4159CCPZ-RL7 の用途: 6 件s: Microwave Signal Generators, RF Communications Test Equipment, Local Oscillator Generation, Industrial RF Measurement, Frequency-Modulated Waveform Generation, Laboratory Frequency Calibration.
Microwave Signal Generators
The ADF4159CCPZ-RL7 fits microwave signal-generator front ends that require programmable output and fine frequency spacing. Its 500 MHz to 13 GHz input range and 25-bit fixed modulus support sub-hertz resolution, while direct modulation can place control information directly on the synthesized waveform. The 2 GHz maximum output frequency covers demanding test and measurement channels within that range. Designers should use the manufacturer loop-filter guidance, preserve a short RF return path, and verify phase noise and spurious performance with the intended reference oscillator. The exposed thermal pad requires adequate copper and via support so that temperature rise does not shift acquisition behavior or disturb the output reference.
おすすめ
RF Communications Test Equipment
The ADF4159CCPZ-RL7 is appropriate for communications test equipment that must synthesize accurately spaced RF channels. A 25-bit fixed modulus provides sub-hertz theoretical resolution, and the 500 MHz to 13 GHz input range offers broad reference-channel coverage for instrumentation operating below the 2 GHz output ceiling. Direct modulation and programmable waveform generation can simplify channel stimulus and modulation tests. The main engineering constraints are reference phase noise, loop bandwidth, output-power calibration, and spur control. Use short, impedance-controlled RF routing, a return path referenced to the exposed pad, and the manufacturer application circuit as the baseline before adding frequency-dependent gain correction or external attenuators.
おすすめ
Local Oscillator Generation
The ADF4159CCPZ-RL7 can generate a programmable local oscillator for RF mixers, receivers, and frequency-conversion stages requiring precise channel selection. Its fractional-N architecture supports fine tuning without relying solely on coarse channel spacing, and direct modulation offers a path to fast frequency or phase control when the receiver architecture permits it. Because the device reaches 13 GHz at its RF input and produces up to 2 GHz, system planners should distinguish the synthesizer input band from the final output band and account for divider settings. Reference spurs, phase noise, leakage, and loop filter component tolerances must be included in the receiver error budget. The exposed pad should be tied to the supply and ground plane according to the recommended land pattern.
おすすめ
Industrial RF Measurement
The ADF4159CCPZ-RL7 supports industrial RF measurement systems that need digitally controlled, repeatable frequency generation. The 13 GHz headline input capability, 25-bit fixed modulus, and programmable reference divider allow a single synthesizer architecture to cover numerous instrument ranges through divider programming. Direct modulation is useful when the test source must reproduce modulated conditions, while fast and slow waveform generation adds flexibility for controlled sweeps. Calibration across the full output band is necessary because RF losses and board parasitics vary with frequency. Place the reference and charge-pump components close to their pins, provide low-inductance supply connections, and include the exposed pad in the thermal model when predicting temperature drift.
おすすめ
Frequency-Modulated Waveform Generation
The ADF4159CCPZ-RL7 is suited to systems that need programmable modulation as well as a synthesized carrier. Direct modulation can reduce the number of separate RF modulation chains, while fast and slow waveform generation supports different modulation trajectories within a single synthesizer design. The 500 MHz to 13 GHz RF input range and 2 GHz maximum output provide a broad operating framework for waveform test and simulation systems. Engineers must still confirm the usable modulation bandwidth, output level, and distortion from the manufacturer datasheet and application circuit. Keep modulation and digital-control traces away from sensitive reference nodes, and validate filtering and amplitude response across the intended waveform bandwidth rather than assuming carrier frequency alone defines performance.
おすすめ
Laboratory Frequency Calibration
The ADF4159CCPZ-RL7 can act as the synthesis element in a laboratory calibration source where fine frequency resolution and programmable control are important. Its sub-hertz resolution and programmable reference architecture are useful for generating closely spaced test tones or calibration points, while the 25-bit fixed modulus allows detailed channel planning. The same architecture can support automated sweep and modulation experiments through its digital control interface. Measurement accuracy will be limited by the external reference, divider accuracy, loop phase noise, and calibration procedure rather than the nominal resolution alone. Use a low-noise reference with a suitable isolation arrangement, validate the loop filter against the desired acquisition time, and preserve ground continuity under the exposed pad during repeated thermal cycling.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADF4159CCPZ-RL7 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADF4159WCCPZ-RL7 | ADF4169CCPZ-RL7 | ADF4169WCCPZ-RL7 | ADF4159CCPZ |
|---|---|---|---|---|---|
| Package | 24-lead LFCSP (CP-24) with exposed pad | 24-lead LFCSP (CP-24) with exposed pad | 24-lead LFCSP (CP-24) with exposed pad | 24-lead LFCSP (CP-24) with exposed pad | 24-lead LFCSP (CP-24) with exposed pad |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Maximum RF Input Frequency | 13 GHz | 13 GHz | 12 GHz | 12 GHz | 13 GHz |
主な差別化要因
- Higher maximum RF input frequency than the ADF4169 alternatives (vs ADF4169CCPZ-RL7)
- Direct modulation with fast and slow waveform generation (vs ADF4107BRU-REEL)
- Sub-hertz fractional-N resolution (vs ADF4169WCCPZ-RL7)
- Same 24-lead footprint across identified family alternatives (vs ADF4159WCCPZ-RL7)
設計ノート
Follow the manufacturer land pattern for the 24-lead CP-24 LFCSP and connect the exposed pad to the ground plane with multiple thermal and electrical vias. Keep the reference input, charge-pump connection, and decoupling components close to their associated pins. A short, continuous ground return is more important than an elaborate external ground connection because RF phase noise and accidental modulation can increase when loop-current paths become inductive.
Treat the reference path as a high-purity signal path even though its operating frequency may be below the RF output. Route it away from the RF output and switching-node areas, use a controlled impedance, and decouple supply pins near the device. When evaluating loop performance, use the same reference, filter, and board construction intended for production because parasitic inductance in the charge-pump and filter nodes can alter damping and acquisition behavior.
Validate direct-modulation bandwidth, output level, phase noise, and spurious signals with the final reference oscillator and loop-filter values. The sub-hertz frequency resolution is a synthesis capability, not a guarantee of absolute accuracy; reference error, divider quantization, leakage, and calibration determine realized accuracy. Keep modulation-control traces short and isolated from the reference and charge-pump nodes to reduce coupling into the synthesized carrier.
The exposed pad is the primary path for removing package heat. Estimate junction temperature from the actual dissipation and board thermal resistance, then verify it across ambient temperature, output frequency, and supply conditions. Use a copper area and via pattern consistent with the manufacturer recommendation. Avoid placing a thermally restrictive cutout beneath the pad, since an isolated pad can raise operating temperature and alter RF performance during long laboratory or industrial measurements.
コンプライアンス情報
The exact-part sources do not explicitly state the compliance status of ADF4159CCPZ-RL7. The W suffix identifies an automotive-qualified family option, but automotive qualification must not be assumed for the standard target MPN.