ADF4360-8BCP - 65-400MHz Integer-N PLL VCO | Analog Devices
部品番号: ADF4360-8BCP ✓ 生産中ADF4360-8BCP 概要
An integer-N frequency synthesizer is a phase-locked-loop-based RF signal source that divides its reference frequency by an integer value to establish the synthesized output. It belongs to the PLL synthesizer and VCO hierarchy, where the PLL locks a voltage-controlled oscillator to a stable reference. This integrated approach reduces the number of discrete RF components required in receivers, transmitters, test equipment, and frequency-conversion systems.
The ADF4360-8 uses external inductors to set the VCO center frequency across its 65 MHz to 400 MHz range. Its three-wire serial interface controls the on-chip registers, while programmable output power allows the RF output level to be adjusted. A digital lock-detect output supports system-level status monitoring, and hardware and software power-down modes help control operating state and power consumption.
The ADF4360-8 integrates both the frequency synthesizer and VCO rather than requiring a separate oscillator. Its integer-N architecture provides a straightforward frequency-setting method derived from the reference input and programmed divider values. The center frequency is established by external inductors, while the synthesizer's register interface controls synthesis, calibration, power-down, lock detection, and output behavior.
Typical uses include local oscillator generation in RF receivers, intermediate-frequency signal sources, communications test equipment, frequency counters, instrumentation, and low-to-medium-frequency RF signal generation. The 65 MHz to 400 MHz operating range is particularly useful where a compact, programmable RF source is needed instead of a fixed-frequency oscillator.
PCB design should preserve the RF return paths associated with the VCO and keep the serial-interface traces away from sensitive RF nodes. Follow the manufacturer's pin-description table, recommended decoupling configuration, and layout guidance. External inductor selection is central to the achievable center frequency, so account for tolerance, parasitic inductance, current capability, and layout effects during design verification.
This page combines the ADF4360-8 technical specifications with practical application guidance, pin and package considerations, comparison data, and design guidance intended to help engineers evaluate the synthesizer beyond a basic catalog listing.
ドロップイン代替品: ADF4360-8BCP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ADF4360-8BCPZ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADF4360-8BCPZRL7
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADF4360-8BCPRL7
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADF4360-8BCP 仕様
| Device Type | Integrated integer-N synthesizer and voltage-controlled oscillator |
| Frequency Range | 65 MHz to 400 MHz |
| Maximum Synthesized Frequency | 400 MHz |
| Minimum Synthesized Frequency | 65 MHz |
| 電源電圧 | 3.6 V |
| Logic Compatibility | 1.8 V |
| Synthesizer Architecture | Integer-N |
| Output Power | Programmable |
| Control Interface | 3-wire serial interface |
| Lock Detection | Digital lock detect |
| Power-Down Modes | Hardware and software power-down |
| VCO Frequency Setting | Set by external inductors |
| パッケージ | 24-lead surface-mount package with exposed pad |
| 実装タイプ | Surface mount |
ADF4360-8BCP 24-lead surface-mount package with exposed pad ピン配置ガイド
ADF4360-8BCP (24-lead surface-mount package with exposed pad パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ADF4360-8BCP.
詳細は データシート をご参照ください。
主な用途
ADF4360-8BCP の用途: 6 件s: RF Receiver Local Oscillator, Communications Test Equipment, Instrumentation Signal Source, Intermediate Frequency Signal Generation, Frequency Counter and Signal Analyzer, Low-Frequency RF Transmitter.
RF Receiver Local Oscillator
The ADF4360-8BCP is appropriate for generating a programmable local-oscillator signal in receivers operating within the 65 MHz to 400 MHz range. Its integrated integer-N PLL and VCO replace a separate oscillator and divider arrangement, while the three-wire serial interface allows frequency changes under firmware control. Digital lock detect can confirm that the loop has settled before the receiver switches signal paths. The external-inductor network and RF layout remain critical: component tolerance and parasitic inductance shift the practical center frequency, and supply or reference noise can affect phase noise and spurious products.
おすすめ
Communications Test Equipment
The ADF4360-8BCP can serve as the programmable RF source in communications test equipment that needs coverage from 65 MHz to 400 MHz. Its register-controlled integer-N architecture allows an instrument to change operating conditions without replacing the synthesizer hardware, and programmable output power provides an additional level of RF control. The digital lock-detect output helps software avoid measurements until the PLL is locked. For calibration systems, the reference oscillator and feedback paths must have suitable phase-noise and isolation characteristics; otherwise, performance can be limited by the test setup rather than the ADF4360-8 itself.
おすすめ
Instrumentation Signal Source
The ADF4360-8BCP suits laboratory and production instrumentation requiring a compact, digitally controlled RF source between 65 MHz and 400 MHz. Integrating the integer-N synthesizer and VCO reduces board area compared with a discrete VCO and frequency-divider implementation. The three-wire interface simplifies connection to a microcontroller or test controller, while hardware and software power-down modes support duty-cycle control. Signal purity must still be evaluated under the intended reference configuration, and the RF output network should use controlled impedance and short return paths to preserve predictable behavior across the operating band.
おすすめ
Intermediate Frequency Signal Generation
The ADF4360-8BCP can generate programmable intermediate-frequency signals within its 65 MHz to 400 MHz range for receiver, demodulator, and signal-chain testing. An integer-N synthesizer provides repeatable frequency relationships to the reference, which is useful when the instrument must generate coherent test tones. Programmable output power allows the generator output to be adjusted without changing the external RF source. Engineers should verify the required frequency accuracy, phase noise, and spur levels against the complete reference and loop settings, then validate the output after board assembly because package parasitics and layout can affect RF performance.
おすすめ
Frequency Counter and Signal Analyzer
The ADF4360-8BCP is useful as an internal reference generator for frequency-counter and signal-analyzer front ends that require a programmable stimulus within the 65 MHz to 400 MHz span. The integrated VCO and PLL allow the instrument to select test frequencies digitally, and lock detect can synchronize measurement sequences with synthesizer readiness. In a multichannel analyzer, reference and RF coupling must be controlled carefully to avoid measurement errors. Designers should also account for loop settling time, which depends on reference and programming choices, before expecting a newly commanded frequency to be immediately usable for calibration.
おすすめ
Low-Frequency RF Transmitter
The ADF4360-8BCP can provide the synthesized RF carrier in compact low-frequency transmitters operating between 65 MHz and 400 MHz. Its integrated architecture supports a compact RF channel, and programmable output power allows operating conditions to be adjusted through the serial interface. The three-wire control bus and digital lock detect simplify connection to a transmitter controller. External inductors define the VCO center frequency, so tolerance and saturation must be checked against the required output range. A power-down function can reduce activity between transmissions, but sequencing must prevent the RF section from operating before the reference and supplies are stable.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADF4360-8BCP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADF4360-8BCPZ | ADF4360-8BCPZRL7 | ADF4360-8BCPRL7 |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-WFQFN exposed pad | 24-WFQFN exposed pad - same | 24-WFQFN exposed pad - same | 24-WFQFN exposed pad - same |
| Device Type | Integer-N synthesizer and VCO | Integer-N synthesizer and VCO | Integer-N synthesizer and VCO | Integer-N synthesizer and VCO |
| Frequency Range | 65 MHz to 400 MHz | 65 MHz to 400 MHz | 65 MHz to 400 MHz | 65 MHz to 400 MHz |
| Supply Voltage | 3.6 V | 3.6 V | 3.6 V | 3.6 V |
| Logic Compatibility | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Control Interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface |
| Output Power | Programmable | Programmable | Programmable | Programmable |
| Lock Detection | Digital lock detect | Digital lock detect | Digital lock detect | Digital lock detect |
| Power-Down Function | Hardware and software power-down | Hardware and software power-down | Hardware and software power-down | Hardware and software power-down |
主な差別化要因
- Integrated PLL and VCO frequency range (vs ADF4360-8BCPZ)
- Programmable RF output control (vs ADF4360-8BCPZRL7)
- Serial control and power management (vs ADF4360-8BCPRL7)
設計ノート
Use the Analog Devices ADF4360-8 evaluation-board layout as the starting point for RF routing, grounding, decoupling, and exposed-pad connection. Keep the VCO and output RF paths compact, provide a continuous ground reference, and avoid routing the three-wire control signals beneath sensitive RF nodes. The external-inductor location is part of the RF structure, so component placement and trace geometry should follow the manufacturer's reference layout rather than a generic low-frequency layout.
Place the recommended input and bypass capacitors directly beside their associated supply pins and connect the exposed pad to the specified ground-plane construction. Use the manufacturer datasheet for capacitor values, voltage ratings, and permitted alternatives. Estimated: if the application has a changing supply or reference condition, test startup and lock behavior across the intended operating environment because decoupling alone cannot correct an inadequate reference or incorrect power sequence.
Do not select the external-inductor network from nominal frequency alone. Account for component tolerance, parasitic capacitance, DC bias, self-resonance, and PCB proximity to copper, all of which can shift the practical VCO center frequency. After assembly, measure the actual output range and lock behavior across the intended frequency plan. Also verify that the serial interface levels meet the 1.8 V logic compatibility requirement and that software observes the digital lock-detect state before using a newly programmed output.
Preserve controlled-impedance routing for RF outputs and minimize discontinuities between the device, output network, and measurement or matching circuit. Keep the reference and feedback paths away from high-current switching nodes to reduce spur conversion. For phase-noise- or spur-sensitive measurements, compare the complete setup with the EV-ADF4360-8EB1Z evaluation environment, including power supplies, reference source, cables, and measurement bandwidth, because external system noise may dominate the synthesizer itself.
コンプライアンス情報
The exact suffix-specific environmental and material compliance declarations are not stated on the ADF4360-8 family product page. Confirm the applicable declaration for the ordered MPN before production release.