Analog Devices

ADF4360-8BCP - 65-400MHz Integer-N PLL VCO | Analog Devices

N.º da peça: ADF4360-8BCP ✓ Ativo
3.6 V Vdss 24-lead surface-mount package with exposed pad Package 65 MHz to 400 MHz Speed
MOQ: 1 |

ADF4360-8BCP Visão geral

The Analog Devices ADF4360-8BCP is an integrated integer-N frequency synthesizer and voltage-controlled oscillator covering 65 MHz to 400 MHz in a 24-lead surface-mount package. It combines a phase-locked loop, a voltage-controlled oscillator, programmable output power, a digital lock-detect function, and a three-wire serial interface. The device operates from a 3.6 V power supply and supports 1.8 V logic compatibility.

An integer-N frequency synthesizer is a phase-locked-loop-based RF signal source that divides its reference frequency by an integer value to establish the synthesized output. It belongs to the PLL synthesizer and VCO hierarchy, where the PLL locks a voltage-controlled oscillator to a stable reference. This integrated approach reduces the number of discrete RF components required in receivers, transmitters, test equipment, and frequency-conversion systems.

The ADF4360-8 uses external inductors to set the VCO center frequency across its 65 MHz to 400 MHz range. Its three-wire serial interface controls the on-chip registers, while programmable output power allows the RF output level to be adjusted. A digital lock-detect output supports system-level status monitoring, and hardware and software power-down modes help control operating state and power consumption.

The ADF4360-8 integrates both the frequency synthesizer and VCO rather than requiring a separate oscillator. Its integer-N architecture provides a straightforward frequency-setting method derived from the reference input and programmed divider values. The center frequency is established by external inductors, while the synthesizer's register interface controls synthesis, calibration, power-down, lock detection, and output behavior.

Typical uses include local oscillator generation in RF receivers, intermediate-frequency signal sources, communications test equipment, frequency counters, instrumentation, and low-to-medium-frequency RF signal generation. The 65 MHz to 400 MHz operating range is particularly useful where a compact, programmable RF source is needed instead of a fixed-frequency oscillator.

PCB design should preserve the RF return paths associated with the VCO and keep the serial-interface traces away from sensitive RF nodes. Follow the manufacturer's pin-description table, recommended decoupling configuration, and layout guidance. External inductor selection is central to the achievable center frequency, so account for tolerance, parasitic inductance, current capability, and layout effects during design verification.

This page combines the ADF4360-8 technical specifications with practical application guidance, pin and package considerations, comparison data, and design guidance intended to help engineers evaluate the synthesizer beyond a basic catalog listing.

Alternativas drop-in para ADF4360-8BCP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

ADF4360-8BCPZ

✅ Drop-In
📦 24-WFQFN exposed pad
Z-suffix ordering code retains the 65-400 MHz range and 24-WFQFN exposed-pad format; verify lead finish, temperature grade, and exact exposed-pad details

📋 Alternativa de referência (fora do catálogo)

ADF4360-8BCPZRL7

✅ Drop-In
📦 24-WFQFN exposed pad
Z-suffix 65-400 MHz device in the same exposed-pad package; differs in ordering or reel configuration rather than core frequency specifications

📋 Alternativa de referência (fora do catálogo)

ADF4360-8BCPRL7

✅ Drop-In
📦 24-WFQFN exposed pad
Same 65-400 MHz ADF4360-8 family and exposed-pad package; RL7 ordering code changes reel or termination configuration rather than core PLL specifications

📋 Alternativa de referência (fora do catálogo)

ADF4360-8BCP Especificações

Device Type Integrated integer-N synthesizer and voltage-controlled oscillator
Frequency Range 65 MHz to 400 MHz
Maximum Synthesized Frequency 400 MHz
Minimum Synthesized Frequency 65 MHz
Tensão de alimentação 3.6 V
Logic Compatibility 1.8 V
Synthesizer Architecture Integer-N
Output Power Programmable
Control Interface 3-wire serial interface
Lock Detection Digital lock detect
Power-Down Modes Hardware and software power-down
VCO Frequency Setting Set by external inductors
Encapsulamento 24-lead surface-mount package with exposed pad
Tipo de montagem Surface mount

Guia de Configuração de Pinos do ADF4360-8BCP 24-lead surface-mount package with exposed pad

Configuração de pinos para ADF4360-8BCP (pacote 24-lead surface-mount package with exposed pad). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 24-lead surface-mount package with exposed pad para ADF4360-8BCP

Nenhum dado detalhado de pinagem disponível para ADF4360-8BCP.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

ADF4360-8BCP é adequado para 6 aplicaçãos: RF Receiver Local Oscillator, Communications Test Equipment, Instrumentation Signal Source, Intermediate Frequency Signal Generation, Frequency Counter and Signal Analyzer, Low-Frequency RF Transmitter.

🌐

RF Receiver Local Oscillator

The ADF4360-8BCP is appropriate for generating a programmable local-oscillator signal in receivers operating within the 65 MHz to 400 MHz range. Its integrated integer-N PLL and VCO replace a separate oscillator and divider arrangement, while the three-wire serial interface allows frequency changes under firmware control. Digital lock detect can confirm that the loop has settled before the receiver switches signal paths. The external-inductor network and RF layout remain critical: component tolerance and parasitic inductance shift the practical center frequency, and supply or reference noise can affect phase noise and spurious products.

🖥️

Communications Test Equipment

The ADF4360-8BCP can serve as the programmable RF source in communications test equipment that needs coverage from 65 MHz to 400 MHz. Its register-controlled integer-N architecture allows an instrument to change operating conditions without replacing the synthesizer hardware, and programmable output power provides an additional level of RF control. The digital lock-detect output helps software avoid measurements until the PLL is locked. For calibration systems, the reference oscillator and feedback paths must have suitable phase-noise and isolation characteristics; otherwise, performance can be limited by the test setup rather than the ADF4360-8 itself.

🔧

Instrumentation Signal Source

The ADF4360-8BCP suits laboratory and production instrumentation requiring a compact, digitally controlled RF source between 65 MHz and 400 MHz. Integrating the integer-N synthesizer and VCO reduces board area compared with a discrete VCO and frequency-divider implementation. The three-wire interface simplifies connection to a microcontroller or test controller, while hardware and software power-down modes support duty-cycle control. Signal purity must still be evaluated under the intended reference configuration, and the RF output network should use controlled impedance and short return paths to preserve predictable behavior across the operating band.

📡

Intermediate Frequency Signal Generation

The ADF4360-8BCP can generate programmable intermediate-frequency signals within its 65 MHz to 400 MHz range for receiver, demodulator, and signal-chain testing. An integer-N synthesizer provides repeatable frequency relationships to the reference, which is useful when the instrument must generate coherent test tones. Programmable output power allows the generator output to be adjusted without changing the external RF source. Engineers should verify the required frequency accuracy, phase noise, and spur levels against the complete reference and loop settings, then validate the output after board assembly because package parasitics and layout can affect RF performance.

📺

Frequency Counter and Signal Analyzer

The ADF4360-8BCP is useful as an internal reference generator for frequency-counter and signal-analyzer front ends that require a programmable stimulus within the 65 MHz to 400 MHz span. The integrated VCO and PLL allow the instrument to select test frequencies digitally, and lock detect can synchronize measurement sequences with synthesizer readiness. In a multichannel analyzer, reference and RF coupling must be controlled carefully to avoid measurement errors. Designers should also account for loop settling time, which depends on reference and programming choices, before expecting a newly commanded frequency to be immediately usable for calibration.

📱

Low-Frequency RF Transmitter

The ADF4360-8BCP can provide the synthesized RF carrier in compact low-frequency transmitters operating between 65 MHz and 400 MHz. Its integrated architecture supports a compact RF channel, and programmable output power allows operating conditions to be adjusted through the serial interface. The three-wire control bus and digital lock detect simplify connection to a transmitter controller. External inductors define the VCO center frequency, so tolerance and saturation must be checked against the required output range. A power-down function can reduce activity between transmissions, but sequencing must prevent the RF section from operating before the reference and supplies are stable.

Resumo dos produtos recomendados

EV-ADF4360-8EB1Z Manufacturer evaluation board containing ADF4360-8BCPZ Usado em: RF Receiver Local Oscillator, Communications Test Equipment, Instrumentation Signal Source, Intermediate Frequency Signal Generation, Frequency Counter and Signal Analyzer, Low-Frequency RF Transmitter ADF4360-8BCPZ Close ordering-code option for the same synthesizer family Usado em: RF Receiver Local Oscillator, Communications Test Equipment, Frequency Counter and Signal Analyzer ADF4360-8BCPZRL7 Same-family ordering option for design evaluation Usado em: Instrumentation Signal Source ADF4360-8BCP Analog Devices Usado em: Intermediate Frequency Signal Generation ADF4360-8BCPRL7 Same-family ordering option for prototype assemblies Usado em: Low-Frequency RF Transmitter
What is the operating frequency range of the ADF4360-8BCP?
The ADF4360-8BCP covers 65 MHz to 400 MHz. According to the Analog Devices ADF4360-8 product page and manufacturer datasheet, the center frequency is established by external inductors. This broad low-to-medium RF range supports programmable local-oscillator generation, IF signal sources, communications test equipment, and instrumentation where an adjustable output is preferred to a fixed-frequency oscillator.
Where can I download the ADF4360-8BCP datasheet PDF?
The official ADF4360-8 product page provides the manufacturer datasheet and technical documentation for the ADF4360-8BCP. It identifies the circuit as an integrated integer-N synthesizer and VCO with a 65 MHz to 400 MHz frequency range. Use the pin-description table, electrical-characteristics section, and application information in that document before assigning PCB nets or calculating the external-inductor network.
Where can I find the ADF4360-8BCP pinout?
Use the pin-description table in the Analog Devices ADF4360-8 manufacturer datasheet to locate the ADF4360-8BCP pinout. The package contains 24 perimeter leads and an exposed pad, so the exposed pad should also be checked against the land-pattern and thermal guidance. Do not infer connections solely from the package outline, because power, ground, reference, RF, and control functions must follow the exact pin-description table.
What are the key specifications of ADF4360-8BCP that engineers should know?
The ADF4360-8BCP is an integrated integer-N PLL synthesizer and VCO with a 65 MHz to 400 MHz output range, 3.6 V supply operation, 1.8 V logic compatibility, programmable RF output power, digital lock detect, and a three-wire serial interface. According to the Analog Devices product page, external inductors set the center frequency. It also supports hardware and software power-down for controlled operating states.
What can replace the ADF4360-8BCP?
The closest documented drop-in replacement is the Analog Devices ADF4360-8BCPZ, which retains the ADF4360-8 synthesizer architecture and 24-lead exposed-pad package while using the Z suffix. The manufacturer supports ADF4360-8BCPZ for evaluation-board use. For any substitution, verify lead finishes, pin assignments, exposed-pad connection, register behavior, external-inductor requirements, and operating-temperature limits against the datasheets.
Is ADF4360-8BCPZ the same as ADF4360-8BCP?
ADF4360-8BCPZ is the closely related Z-suffix member of the ADF4360-8 family and is the most practical drop-in candidate because the core PLL, 65 MHz to 400 MHz range, package format, and register-based control remain aligned. Before treating it as identical, confirm the exact pin table, lead or termination finish, exposed-pad layout, temperature range, and procurement requirements for the assembled PCB.
What is the best Analog Devices equivalent for the ADF4360-8BCP?
The ADF4360-8BCPZ is the best Analog Devices drop-in candidate identified for the ADF4360-8BCP because it belongs to the same ADF4360-8 family and uses the corresponding 24-lead exposed-pad format. The Analog Devices evaluation-board description specifically identifies ADF4360-8BCPZ as the fitted synthesizer. Final equivalence still depends on pin-level, temperature, and lifecycle checks for the specific production design.
ADF4360-8BCP vs ADF4360-8BCPZ: which is better for a new design?
The ADF4360-8BCPZ is generally preferable for a new RoHS-oriented design when its lead finish, temperature rating, and availability satisfy the requirements. Both parts belong to the same 65 MHz to 400 MHz ADF4360-8 synthesizer family and use a 24-lead exposed-pad package. Existing boards may retain ADF4360-8BCP for continuity, while new designs should verify the current manufacturer ordering information and complete pin-level compatibility.
When should I choose ADF4360-8BCP over ADF4360-8BCPZ?
Choose ADF4360-8BCP when an existing design already uses that exact ordering code and its qualification, temperature, and lifecycle requirements remain satisfactory. Choose ADF4360-8BCPZ for a new assembly when its documented suffix, termination, and qualification conditions fit the production program. Both devices occupy the same core ADF4360-8 application space, so the decision should be based on exact ordering-code and assembly requirements rather than frequency capability.
Is the ADF4360-8BCP suitable for RF receiver and test applications?
The ADF4360-8BCP is suitable for programmable RF receiver and test applications requiring an output from 65 MHz to 400 MHz. Its integrated PLL and VCO, programmable output power, three-wire serial control, and digital lock-detect feature support controlled RF signal generation. Performance depends on the reference source, external inductor design, board layout, output filtering, and required phase-noise and spur performance.
How much supply voltage does the ADF4360-8BCP require?
The ADF4360-8BCP operates from a 3.6 V supply and supports 1.8 V logic compatibility. According to the Analog Devices ADF4360-8 manufacturer documentation, the 3.6 V value describes the device power supply rather than the programmable output amplitude. Confirm individual pin voltage limits, decoupling values, and absolute-maximum ratings in the datasheet before applying it to a new board.
How is the ADF4360-8BCP VCO frequency set?
The ADF4360-8BCP sets its VCO center frequency with external inductors. Its integrated integer-N PLL then relates that oscillator to the reference input and programmed integer divider, allowing the synthesized RF output to cover 65 MHz to 400 MHz. The exact inductance depends on the target center frequency and system conditions, so use the manufacturer's selection guidance and verify the final network on hardware.
What are the power-management features of the ADF4360-8BCP?
The ADF4360-8BCP provides both hardware and software power-down modes, allowing the synthesizer to enter a controlled low-power state when it is not needed. It also supports digital lock detection and programmable RF output power. These functions help simplify instrument control and reduce unnecessary RF activity, although the exact power-down sequence and register behavior must follow the manufacturer datasheet.
What is the lifecycle status of the ADF4360-8BCP?
The ADF4360-8BCP is presented on Analog Devices' active ADF4360-8 product page and remains associated with a manufacturer evaluation board, indicating ongoing product-family support. For production planning, request current lifecycle confirmation and the exact ordering-code status through the Request a Quote form on this page. This avoids relying on historical catalog availability when long-term sourcing commitments are being made.
Where can I buy the ADF4360-8BCP and check its lead time?
Use the Request a Quote form on this page to request ADF4360-8BCP pricing, current availability, minimum order quantity, and production lead time. The form routes the request for the exact ADF4360-8BCP ordering code, which is important because suffix, package, and termination differences can affect interchangeability. Confirm lot traceability and counterfeit-avoidance inspection requirements before placing a production order.
Is the ADF4360-8BCP in stock and what does it cost?
Current stock, allocation, and a binding quotation for the ADF4360-8BCP should be requested through the Request a Quote form on this page. Quote-first confirmation is necessary because the exact suffix, lead finish, package, and volume determine the current supply position. Share the required quantity, target date, and inspection requirements with the quote request so the manufacturing schedule can be evaluated accurately.

Dados de referência de engenharia para ADF4360-8BCP — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the ADF4360-8BCP for an existing 65 MHz to 400 MHz RF design that uses its exact ordering code and has completed all qualification and lifecycle checks. ADF4360-8BCPZ is the preferred drop-in candidate for new layouts because it is documented with the same family and in the manufacturer's evaluation-board BOM, but its exact lead finish, temperature grade, and exposed-pad details should be confirmed. ADF4360-8BCPZRL7 and ADF4360-8BCPRL7 can suit assembly configurations requiring different reel or ordering arrangements. All candidates retain the integrated integer-N PLL, programmable output, digital lock detect, and three-wire control architecture. If a design requires a frequency range outside 65 MHz to 400 MHz, select another member of the ADF436x family rather than forcing a package-level substitution. Final sourcing decisions should also account for current lifecycle status, production quantities, and traceable inspection requirements.

Comparação com alternativas

Parâmetro Este produto ADF4360-8BCPZ ADF4360-8BCPZRL7 ADF4360-8BCPRL7
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 24-WFQFN exposed pad 24-WFQFN exposed pad - same 24-WFQFN exposed pad - same 24-WFQFN exposed pad - same
Device Type Integer-N synthesizer and VCO Integer-N synthesizer and VCO Integer-N synthesizer and VCO Integer-N synthesizer and VCO
Frequency Range 65 MHz to 400 MHz 65 MHz to 400 MHz 65 MHz to 400 MHz 65 MHz to 400 MHz
Supply Voltage 3.6 V 3.6 V 3.6 V 3.6 V
Logic Compatibility 1.8 V 1.8 V 1.8 V 1.8 V
Control Interface 3-wire serial interface 3-wire serial interface 3-wire serial interface 3-wire serial interface
Output Power Programmable Programmable Programmable Programmable
Lock Detection Digital lock detect Digital lock detect Digital lock detect Digital lock detect
Power-Down Function Hardware and software power-down Hardware and software power-down Hardware and software power-down Hardware and software power-down

Principais diferenciais

  • Integrated PLL and VCO frequency range (vs ADF4360-8BCPZ)
  • Programmable RF output control (vs ADF4360-8BCPZRL7)
  • Serial control and power management (vs ADF4360-8BCPRL7)

Notas de projeto

Use the Analog Devices ADF4360-8 evaluation-board layout as the starting point for RF routing, grounding, decoupling, and exposed-pad connection. Keep the VCO and output RF paths compact, provide a continuous ground reference, and avoid routing the three-wire control signals beneath sensitive RF nodes. The external-inductor location is part of the RF structure, so component placement and trace geometry should follow the manufacturer's reference layout rather than a generic low-frequency layout.

Place the recommended input and bypass capacitors directly beside their associated supply pins and connect the exposed pad to the specified ground-plane construction. Use the manufacturer datasheet for capacitor values, voltage ratings, and permitted alternatives. Estimated: if the application has a changing supply or reference condition, test startup and lock behavior across the intended operating environment because decoupling alone cannot correct an inadequate reference or incorrect power sequence.

Do not select the external-inductor network from nominal frequency alone. Account for component tolerance, parasitic capacitance, DC bias, self-resonance, and PCB proximity to copper, all of which can shift the practical VCO center frequency. After assembly, measure the actual output range and lock behavior across the intended frequency plan. Also verify that the serial interface levels meet the 1.8 V logic compatibility requirement and that software observes the digital lock-detect state before using a newly programmed output.

Preserve controlled-impedance routing for RF outputs and minimize discontinuities between the device, output network, and measurement or matching circuit. Keep the reference and feedback paths away from high-current switching nodes to reduce spur conversion. For phase-noise- or spur-sensitive measurements, compare the complete setup with the EV-ADF4360-8EB1Z evaluation environment, including power supplies, reference source, cables, and measurement bandwidth, because external system noise may dominate the synthesizer itself.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The exact suffix-specific environmental and material compliance declarations are not stated on the ADF4360-8 family product page. Confirm the applicable declaration for the ordered MPN before production release.

Dados verificados em: 2026-11-10 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

adf4360 1bcpz adf4360 7bcpz adf4360 7bcpzrl7 ADF4360-8BCP datasheet ADF4360-8BCP datasheet pdf ADF4360-8BCP pinout ADF4360-8BCP equivalent ADF4360-8BCP replacement ADF4360-8BCP vs ADF4360-8BCPZ ADF4360-8BCP 65 400 MHz ADF4360-8BCP price ADF4360-8BCP stock Analog Devices ADF4360-8BCP ADF4360-8BCP application circuit

Componentes & termos relacionados

Analog Devices ADF4360-8BCP ADF4360-8BCPZ ADF4360-8BCPZRL7 ADF4360-8BCPRL7 EV-ADF4360-8EB1Z integer-N frequency synthesizer phase-locked loop PLL voltage-controlled oscillator VCO clock generator clock and timing IC integrated circuit semiconductor 65 MHz to 400 MHz 3.6 V power supply 1.8 V logic compatibility programmable output power digital lock detect 3-wire serial interface external inductor hardware power-down software power-down 24-WFQFN exposed pad
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ