Analog Devices

ADM3061EARZ - 500 kbps Half-Duplex RS-485 Transceiver | Analog Devices

部品番号: ADM3061EARZ ✓ 生産中
3.0 V to 5.5 V Vdss 8-lead SOIC Package
MOQ: 1 |

ADM3061EARZ 概要

The Analog Devices ADM3061EARZ is a half-duplex RS-485 interface transceiver operating from 3.0 V to 5.5 V, with a 500 kbps data rate and IEC ESD protection up to ±12 kV in an 8-lead SOIC package. It combines a differential RS-485 driver, differential receiver, and half-duplex control interface for robust bidirectional communication over industrial cabling.

An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus voltages and reconstructs digital data from those differential signals. This device belongs to the RS-485 transceiver family within the broader communication-interface and industrial-transceiver hierarchy. Differential signaling improves common-mode noise immunity and allows reliable data transmission across longer cable runs when the bus is correctly terminated and biased.

The ADM3061E family provides a 500 kbps maximum signaling rate, a 3.0 V to 5.5 V supply range, and enhanced ESD protection rated to ±12 kV. Its half-duplex architecture supports a shared A and B bus pair, while the receiver output and driver-enable path support controlled bus direction. The 8-lead SOIC package also has an evaluation-board footprint described by Analog Devices for rapid circuit evaluation.

The 500 kbps operating rate makes the transceiver suitable for moderate-speed industrial links rather than the highest-speed data buses. Its protection capability is particularly useful in factory automation, instrumentation, building controls, and communications equipment where connected cables may be exposed to electrostatic discharge. Designers must still provide appropriate bus protection, grounding, and cable-signal-rate engineering for the complete interface.

Typical uses include industrial RS-485 gateways, sensor and actuator networks, process-control equipment, factory-floor controllers, building-management interfaces, and isolated or ruggedized communication modules. The device can also support legacy peripheral buses where an existing host controller uses TTL or CMOS logic and the external wiring requires an RS-485 physical layer.

For a new board, follow the Analog Devices ADM3061E datasheet for pin assignment, recommended decoupling, bus termination, failsafe behavior, and layout guidance. Keep the A and B differential pair routed together over a controlled ground plane, place termination and protection components near the connector, and account for the logic level on DI, DE, and RO when connecting the transceiver to the host controller.

This page combines the exact ADM3061EARZ device specifications, sourcing information, documented drop-in alternatives, comparison data, and practical PCB-design guidance to support faster component selection and implementation in industrial RS-485 systems.

ドロップイン代替品: ADM3061EARZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

ADM3061EBRZ

✅ ドロップイン
📦 8-lead SOIC
Same 500 kbps rate, half-duplex operation, 3.0 V to 5.5 V supply range, and ±12 kV IEC ESD rating; device-specific logic thresholds and timing require datasheet confirmation

📋 参考代替品(カタログ未掲載)

ADM3061EARZ 仕様

Product Type Half-duplex RS-485 transceiver
Supply Voltage Range 3.0 V to 5.5 V
Maximum Data Rate 500 kbps
ESD Protection ±12 kV IEC
Duplex Mode Half duplex
Bus Standard RS-485
パッケージ 8-lead SOIC
Lead Count 8 leads
実装タイプ Surface mount
Driver and Receiver Configuration 1 transmitter and 1 receiver
Bus Input Impedance 1/4 unit load
Maximum Nodes on Bus 128 transceivers

ADM3061EARZ 8-lead soic ピン配置ガイド

ADM3061EARZ (8-lead soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

ADM3061EARZ の 8-lead soic パッケージピン配置図

詳細なピン配置データはありません: ADM3061EARZ.

詳細は データシート をご参照ください。

主な用途

ADM3061EARZ の用途: 6 件s: Industrial Sensor Networks, Process-Control Equipment, Building Automation Gateways, Actuator and Motor-Control Networks, Data Acquisition Systems, Instrumentation and Test Equipment.

🏭

Industrial Sensor Networks

The ADM3061EARZ fits industrial sensor networks that distribute measurements from remote sensors over an RS-485 bus. Its 500 kbps maximum rate is suitable for moderate-volume process data and control commands, while the 1/4-unit-load input impedance permits up to 128 transceivers on the bus. The ±12 kV IEC ESD protection provides a useful interface margin when sensor wiring leaves a controlled enclosure, although external surge protection may still be required. Place the A and B pair over a continuous ground plane, retain the specified bus topology, and terminate only the physical ends of the cable.

⚙️

Process-Control Equipment

The ADM3061EARZ is appropriate for process-control equipment that must communicate over a wired differential bus while operating from 3.3 V or 5 V logic. The 500 kbps rate accommodates setpoints, alarms, and periodic process variables without imposing the cost and layout complexity of a very high-speed transceiver. Its half-duplex architecture reduces bus wiring, but the host controller must enforce drive-enable timing and release the bus before the receiver is read. The 8-lead SOIC package also simplifies assembly on conventional industrial controller boards.

🏠

Building Automation Gateways

The ADM3061EARZ can connect a building-management gateway to field equipment over an RS-485 network. Its 500 kbps data rate is suitable for HVAC controllers, room sensors, access-control equipment, and lighting interfaces that exchange moderate amounts of control data. The 3.0 V to 5.5 V operating range supports embedded processors and programmable controllers, while ±12 kV IEC ESD protection improves robustness in wiring environments exposed to human contact. Follow controlled-impedance, surge-protection, and grounding practices appropriate to the building wiring length.

🔧

Actuator and Motor-Control Networks

The ADM3061EARZ is useful in actuator and motor-control networks that distribute commands to remote drive or I/O modules. Half-duplex operation allows command and status traffic to share the same A/B conductors, while 500 kbps provides adequate bandwidth for supervisory control rather than high-bandwidth motion feedback. The ESD-protected bus interface is valuable in cabinets containing relays, contactors, and long field harnesses. Separate high-current switching paths from the differential pair, use chassis-grounding and transient-protection methods, and avoid allowing inductive switching energy to enter the transceiver supply or signal pins.

📊

Data Acquisition Systems

The ADM3061EARZ supports data-acquisition systems that collect measurements from multiple remote modules. A 500 kbps bus can carry regularly sampled process values and configuration updates, while the 1/4-unit-load receiver permits a large device count without an unusually heavy bus load. Its ±12 kV IEC ESD rating is advantageous where sensors connect through external cables. Select cable baud rate and termination for the total network length, keep transceiver and termination components near the connector, and route the differential pair as a coupled pair to preserve noise immunity.

🔬

Instrumentation and Test Equipment

The ADM3061EARZ is suitable for laboratory and field instrumentation that uses RS-485 as a multipoint command and measurement bus. Its 500 kbps limit supports instrument status, configuration, and sampled results while the half-duplex design simplifies connector wiring. The 3.0 V to 5.5 V range allows direct use with common digital controllers, and the ±12 kV IEC protection rating improves reliability when leads are connected and disconnected. Use a defined bus master, command addressing, timeout handling, and controlled bus direction to prevent two devices from driving the pair simultaneously.

What is the ADM3061EARZ?
The ADM3061EARZ is a half-duplex RS-485 transceiver for 3.0 V to 5.5 V operation, supporting data rates up to 500 kbps and IEC ESD protection up to ±12 kV. Analog Devices describes it as an ESD-protected RS-485 interface device and packages the ADM3061EARZ in an 8-lead SOIC. It is intended for industrial and instrumentation links requiring differential bus signaling, driver-enable control, and receiver output.
What is the operating voltage of ADM3061EARZ?
The ADM3061EARZ operates from 3.0 V to 5.5 V. This range allows use with common 3.3 V and 5 V system rails, although logic-level compatibility with the connected controller must still be confirmed. The voltage range, half-duplex operation, and 500 kbps rate are identified in the Analog Devices product information and Mouser product listing for the device.
What is the maximum data rate of ADM3061EARZ?
The ADM3061EARZ supports a maximum data rate of 500 kbps. This makes it appropriate for moderate-speed industrial control and instrumentation buses rather than high-speed data-center or video links. Analog Devices also describes the ADM3061E family as supporting up to 50 Mbps in some device variants, but the exact ADM3061EARZ operating designation is 500 kbps.
Does ADM3061EARZ support half-duplex communication?
Yes, the ADM3061EARZ is a half-duplex RS-485 transceiver, so the driver and receiver share the same differential bus connection. A direction-control mechanism allows the host controller to enable transmission and return to receive mode afterward. This arrangement reduces wiring compared with full-duplex implementations but requires correct driver-enable timing to avoid contention.
Where can I download the ADM3061EARZ datasheet PDF?
The official documentation is available through the Analog Devices ADM3061E product page, which links to the complete device data sheet and evaluation information. The manufacturer also references user guide UG-1172 for the associated evaluation board. Use the Analog Devices page as the authoritative source for pin assignments, electrical characteristics, application circuits, and recommended layout details.
Where can I find the ADM3061EARZ pinout?
The ADM3061EARZ pin assignment is defined in the manufacturer’s ADM3061E datasheet, with an 8-lead SOIC footprint also supported by the Analog Devices EVAL-RS485HDEBZ evaluation board. The evaluation-board description identifies the driver input, driver enable, receiver output, and A/B bus connections. Use the pin-description table in the datasheet when assigning PCB tracks and protection networks.
What is the best drop-in replacement for ADM3061EARZ?
The ADM3061EBRZ is the closest documented same-brand candidate because it is also described as a half-duplex, 500 kbps, 8-lead SOIC RS-485 transceiver with ±12 kV IEC ESD protection. Confirm its device-specific electrical limits and control logic against the ADM3061EARZ datasheet before substitution. A final replacement should also be checked for lifecycle, qualification, and sourcing requirements.
Can ADM3061EBRZ replace ADM3061EARZ?
The ADM3061EBRZ can be considered for evaluation as an ADM3061EARZ replacement because the comparison identifies the same half-duplex RS-485 configuration, 500 kbps data rate, 8-lead SOIC package, and ±12 kV IEC ESD protection. Pin compatibility must still be confirmed against both datasheets, especially input thresholds, receiver output behavior, and failsafe timing, before approving it as a production drop-in.
ADM3061EARZ vs ADM3061EBRZ: which is better for an industrial bus?
Choose the ADM3061EARZ when it matches the exact requirements of an existing design, and evaluate the ADM3061EBRZ when a documented alternative in the same 8-lead SOIC format is needed. Both are identified as 500 kbps, half-duplex RS-485 transceivers with ±12 kV IEC ESD protection. The decision should depend on verified pin-level behavior, lifecycle status, and qualification for the intended industrial environment.
When should I choose ADM3061EARZ over ADM3061EBRZ?
Select ADM3061EARZ when its verified device-specific characteristics and lifecycle status align with the production design and the ADM3061EBRZ introduces an unverified functional change. Both devices occupy the same 8-lead SOIC category and offer the same headline 500 kbps, half-duplex RS-485 operation. Use the manufacturer data sheets to compare thresholds, timing, failsafe response, and application-specific qualification.
Is ADM3061EARZ suitable for industrial factory automation?
The ADM3061EARZ is suitable for many factory-automation interfaces because it combines a 500 kbps RS-485 link with ±12 kV IEC ESD protection. Its 3.0 V to 5.5 V supply range supports common embedded-controller rails, and the 1/4-unit-load input impedance permits up to 128 transceivers on a bus. Cable routing, grounding, surge protection, and termination still require system-level engineering.
How much ESD protection does ADM3061EARZ provide?
The ADM3061EARZ provides ESD protection rated at ±12 kV according to IEC criteria. This is a strong fit for externally wired industrial equipment where cables may be exposed to electrostatic discharge. The rating applies to the specified device interface and test conditions; it does not replace external surge protection for severe industrial transients.
How many RS-485 nodes can be connected to an ADM3061EARZ bus?
An ADM3061EARZ bus can support as many as 128 transceivers because the ADM3061 and ADM3062 families use a 1/4-unit-load input impedance. Actual population depends on cable length, topology, termination, data rate, and the load presented by every connected node. The manufacturer’s bus guidance should be applied before using the maximum device count in a field installation.
Where can I buy ADM3061EARZ and check its current lead time?
Use the Request a Quote form on this page to request the current ADM3061EARZ unit price, stock position, lead time, and order quantity. The form connects the request to XAIPART’s quotation workflow without embedding a potentially stale commercial value in the technical content. Specify the required package suffix and production quantity when requesting the quotation.
What are the key specifications engineers should know about ADM3061EARZ?
The ADM3061EARZ is a 3.0 V to 5.5 V, half-duplex RS-485 transceiver rated for 500 kbps operation and ±12 kV IEC ESD protection. It uses an 8-lead SOIC package and provides a 1/4-unit-load bus input impedance, allowing up to 128 transceivers on a bus. These are the principal constraints for bus speed, node count, protection, and board layout.

エンジニアリング参考データ: ADM3061EARZ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the ADM3061EARZ when the design requires a 3.0 V to 5.5 V, half-duplex RS-485 interface rated for 500 kbps with ±12 kV IEC ESD protection in an 8-lead SOIC package. These characteristics suit industrial instruments, sensor networks, building controls, and process equipment where a wired differential bus is required. The ADM3061EBRZ is the closest documented candidate when supply continuity or a second-source assessment requires another device in the same family. Its listed package, data rate, duplex mode, supply range, and ESD rating align with the target. Before using it as a production drop-in, verify pin-level behavior, input thresholds, receiver output timing, failsafe response, operating-temperature limits, lifecycle status, and qualification requirements against the manufacturer’s data sheets. Do not select either device for links that require a data rate above 500 kbps, and do not assume the ESD rating replaces external surge protection.

代替品との比較

パラメータ この製品 ADM3061EBRZ
Brand Analog Devices Analog Devices
Package 8-lead SOIC 8-lead SOIC
Product Type Half-duplex RS-485 transceiver Half-duplex RS-485 transceiver
Supply Voltage Range 3.0 V to 5.5 V 3.0 V to 5.5 V
Maximum Data Rate 500 kbps 500 kbps
ESD Protection ±12 kV IEC ±12 kV IEC
Duplex Mode Half duplex Half duplex
Evaluation Board EVAL-RS485HDEBZ supports an 8-lead SOIC footprint EVAL-ADM3061EEB1Z includes an 8-lead MSOP footprint

主な差別化要因

  • Documented 500 kbps half-duplex RS-485 operation (vs ADM3061EBRZ)
  • ±12 kV IEC ESD protection (vs ADM3061EBRZ)
  • Wide 3.0 V to 5.5 V operating range (vs ADM3061EBRZ)

設計ノート

Route the A and B conductors as a tightly coupled differential pair over a continuous ground plane, avoiding plane splits, test pads, and unrelated high-current paths. Keep the transceiver, termination network, and protection components close to the board entry point. The analog and digital return current must not share a narrow neck between the connector and transceiver because common-impedance inductance can convert switching current into differential bus noise.

Treat driver-enable timing as part of the communication protocol. Assert the driver only while the host transmits, then deassert it before reading the receiver output. Allow the bus to settle before interpreting data, and ensure that only one node drives at a time. Incorrect direction control can create driver contention, elevate current, distort signals, and damage the interface.

Apply termination at the two physical ends of the RS-485 bus rather than at every node. Verify the cable length, topology, node count, and data rate before using the documented 500 kbps limit. The 1/4-unit-load receiver supports up to 128 transceivers, but population does not guarantee reliable communication over an arbitrarily long or poorly terminated cable.

Use the manufacturer’s recommended local supply decoupling and place it directly beside the device power pins. Keep the RS-485 bus pins and protection components away from switching nodes and high-current return paths. External surge protection may still be required for industrial installations because the ±12 kV IEC ESD rating addresses electrostatic discharge rather than every overvoltage event encountered on long field wiring.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The product information identifies ±12 kV IEC ESD protection, but specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not stated in the available manufacturer and distributor snippets.

データ検証日: 2026-11-19 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

ADM3061EARZ datasheet ADM3061EARZ pinout ADM3061EARZ datasheet pdf ADM3061EARZ equivalent ADM3061EARZ replacement ADM3061EARZ vs ADM3061EBRZ ADM3061EARZ price ADM3061EARZ stock Analog Devices ADM3061EARZ ADM3061EARZ 8-SOIC pinout ADM3061EARZ RS-485 application circuit ADM3061EARZ 500 kbps transceiver

関連部品&用語

Analog Devices ADM3061EARZ ADM3061EBRZ RS-485 RS-485 transceiver half-duplex transceiver interface IC industrial transceiver differential signaling 3.0 V to 5.5 V 500 kbps ±12 kV IEC ESD protection 1/4 unit load 128-transceiver bus 8-lead SOIC SOIC package family surface-mount package EVAL-RS485HDEBZ EVAL-ADM3061EEB1Z UG-1172 factory automation process control building automation data acquisition IEC
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示