ラストタイムバイのお知らせ: ADM3491EARZ は生産終了が近づいています。最終注文日: お問い合わせ. 利用可能な代替部品を見る →
Analog Devices

ADM3491EARZ - 3.3V Full-Duplex RS-485/RS-422 Transceiver | Analog Devices

部品番号: ADM3491EARZ ⚠ ラストタイムバイ
3.3 V Vdss 14-pin SOIC, 3.90 mm width Package
MOQ: 1 |

ADM3491EARZ 概要

The Analog Devices ADM3491EARZ is a 3.3 V, low-power differential RS-485/RS-422 transceiver with ±15 kV ESD protection, a maximum data rate of 12 Mbps, and full-duplex operation in a 14-pin SOIC package. It provides a combined line driver and receiver for balanced industrial communication links.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and receives those transmissions back into logic-level signals. Differential signaling improves noise immunity and allows communication over longer cables than single-ended interfaces. The RS-485 standard supports multipoint bus arrangements, while RS-422 provides a dedicated driver-to-receiver relationship.

The ADM3491EARZ operates from a single 3.3 V supply and supports full-duplex communication. Its ±15 kV ESD protection is intended to improve robustness against electrostatic discharge encountered on industrial wiring. The 12 Mbps maximum signaling rate supports high-speed data links, although the usable rate over an installed cable also depends on cable length, impedance, topology, termination, and transceiver characteristics.

This device belongs to Analog Devices' ADM3491E family of low-power RS-485 and RS-422 transceivers. The family supports communication on multipoint bus transmission lines and complies with TIA/EIA RS-485 and RS-422 requirements. Full-duplex operation separates the transmit and receive paths, allowing simultaneous bidirectional traffic without sharing the same pair of bus conductors.

Typical uses include industrial control links, factory automation equipment, building automation, instrumentation, and embedded systems that connect a controller to a remote transceiver over a balanced cable. A full-duplex implementation generally uses separate differential pairs for transmission and reception, together with appropriate cable termination at the physical ends of each pair.

Designers should confirm receiver and driver enable polarity, bus topology, termination, and protection requirements against the manufacturer datasheet. The external circuit should also provide stable 3.3 V decoupling, controlled driver transitions, and a return path for the differential signals.

This product page combines lifecycle information, interface specifications, compatible replacement candidates, and practical bus-design guidance to support component selection and PCB implementation for RS-485 and RS-422 systems.

ドロップイン代替品: ADM3491EARZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: ADM3491EARZ (同一形状・フットプリント) — 相違点: Package, Duplex Mode, Bus Configuration, Maximum Data Rate.

Analog Devices
Package: 8-pin SOIC
Duplex Mode: Half-duplex
Bus Configuration: Multipoint differential bus
比較対象 ADM3491EARZ →
Analog Devices
Package: 14-pin SOIC
Maximum Data Rate: 10 Mbps
比較対象 ADM3491EARZ →

ADM3491AR-1

✅ ドロップイン ⚠️ 仕様未検証
📦 14-SOIC
Same ADM3491-family full-duplex function and 14-SOIC format; approximately 10% aggregate parameter difference, with the exact ESD and electrical deltas requiring manufacturer-datasheet confirmation.

📋 参考代替品(カタログ未掲載)

ADM3491AR

✅ ドロップイン ⚠️ 仕様未検証
Analog Devices
📦 14-SOIC
RS-485/RS-422 differential line transceiver · 3.3 V · 10 Mbps · 1 transmitter and 1 receiver · Full duplex · 19 kΩ · 50 transceivers · 840 μA

価格はお問い合わせください

データシートを見る →

MAX3491CSD+

✅ ドロップイン
📦 14-SOIC
Cross-brand 14-SOIC full-duplex transceiver candidate; approximately 20% aggregate parameter difference, with exact data-rate, common-mode, and ESD differences requiring manufacturer-datasheet confirmation.

📋 参考代替品(カタログ未掲載)

MAX3491ECSD+

✅ ドロップイン
📦 14-SOIC
Cross-brand 14-SOIC full-duplex transceiver candidate; approximately 20% aggregate parameter difference, with exact enable, ESD, and common-mode differences requiring manufacturer-datasheet confirmation.

📋 参考代替品(カタログ未掲載)

SP3076EEN-L

✅ ドロップイン
📦 14-SOIC
Cross-brand 14-SOIC transceiver candidate with approximately 30% aggregate parameter difference; verify data rate, receiver common-mode range, ESD level, and enable polarity against the ADM3491EARZ datasheet.

📋 参考代替品(カタログ未掲載)

ADM3491EARZ 仕様

電源電圧 3.3 V
Interface Standard TIA/EIA RS-485 and TIA/EIA RS-422
Transceiver Configuration 1 transmitter and 1 receiver
Duplex Mode Full duplex
Maximum Data Rate 12 Mbps
ESD Protection ±15 kV
Low-Power Operation Low-power transceiver with shutdown mode
Supply Architecture Single +3.3 V supply
パッケージ 14-pin SOIC, 3.90 mm width
実装タイプ Surface mount
Bus Configuration Multipoint bus transmission line
Driver Enable Control DE/RE control
RoHS ステータス Compliant
REACH Status Compliant
Halogen-Free Status Compliant

ADM3491EARZ 14-pin soic, 3.90 mm width ピン配置ガイド

ADM3491EARZ (14-pin soic, 3.90 mm width パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

ADM3491EARZ の 14-pin soic, 3.90 mm width パッケージピン配置図

詳細なピン配置データはありません: ADM3491EARZ.

詳細は データシート をご参照ください。

主な用途

ADM3491EARZ の用途: 6 件s: Industrial Control Communications, Factory Automation Equipment, Building Automation Networks, Instrumentation and Test Systems, Embedded Serial Bus Gateways, Industrial Data Acquisition.

🏭

Industrial Control Communications

The ADM3491EARZ fits full-duplex industrial control links that require a 3.3 V RS-485 or RS-422 interface. Its 12 Mbps maximum data rate provides ample link margin for controller-to-peripheral traffic, while ±15 kV ESD protection improves robustness at connector-facing circuitry. The full-duplex architecture uses separate transmit and receive paths, allowing simultaneous command and response traffic. The main design consideration is ensuring that cable impedance, termination, transceiver enable sequencing, and grounding satisfy the operating distance of the installed bus.

🏭

Factory Automation Equipment

The ADM3491EARZ can connect factory automation controllers, remote I/O modules, and production equipment over balanced wiring. Its single 3.3 V supply simplifies integration with modern embedded control logic, and its full-duplex configuration permits continuous status reporting without sharing a conductor pair with command transmission. The ±15 kV ESD rating is particularly relevant around externally accessible equipment cables. Engineers should still assess industrial noise, ground-loop behavior, surge requirements, and connector placement, because transceiver protection does not replace a complete system-level protection strategy.

🧩

Building Automation Networks

The ADM3491EARZ suits low-power building automation nodes that exchange balanced data between controllers, sensors, gateways, and remote panels. Its 3.3 V operation and shutdown capability support compact, power-conscious equipment, while the 12 Mbps signaling rate accommodates common automation message traffic. Full-duplex operation simplifies designs that need independent request and response paths. The board should use controlled cable routing and appropriate termination to reduce reflections and noise coupling, particularly where automation wiring runs near motors, lighting systems, and switching power equipment.

🔧

Instrumentation and Test Systems

The ADM3491EARZ is suitable for test and measurement instruments that distribute commands or collect data from remote fixtures over a balanced bus. The transceiver's 12 Mbps maximum rate supports fast data exchange, while full-duplex communication allows a controller to issue commands and receive results concurrently. Differential signaling helps preserve data integrity in environments containing switching converters and other noise sources. Designers should select cable length, baud rate, and termination as a coordinated system, and should verify that every device on the bus shares compatible electrical limits.

🌐

Embedded Serial Bus Gateways

The ADM3491EARZ can bridge a low-speed embedded processor to an RS-485 or RS-422 field bus. A 3.3 V processor can typically share the transceiver's supply rail, reducing level-shifting requirements, while the full-duplex interface supports simultaneous host commands and peripheral responses. The 12 Mbps capability allows a gateway to participate in faster links when the physical installation supports that rate. Firmware should coordinate driver-enable and receiver-enable signals, and the PCB should keep the transceiver close to the connector and bus routing.

📡

Industrial Data Acquisition

The ADM3491EARZ fits distributed data-acquisition networks that connect measurement electronics to a central controller. Balanced differential signaling improves noise immunity over longer cable runs, and the 12 Mbps maximum rate supports rapid collection of synchronized or high-volume data. Full-duplex operation lets acquisition nodes transmit samples while receiving configuration commands. For reliable deployment, match the baud rate to cable length, place termination only where required by the bus topology, provide a continuous signal-reference path, and review grounding so that voltage offsets do not exceed receiver limits.

おすすめ製品の概要

MAX3491CSD+ Full-duplex RS-485/RS-422 interface candidate 使用用途: Industrial Control Communications, Building Automation Networks, Embedded Serial Bus Gateways SP3076EEN-L Differential transceiver candidate 使用用途: Industrial Control Communications, Embedded Serial Bus Gateways ADM3491AR-1 Same-family full-duplex interface candidate 使用用途: Factory Automation Equipment, Instrumentation and Test Systems MAX3491ECSD+ Cross-brand differential transceiver candidate 使用用途: Factory Automation Equipment, Instrumentation and Test Systems, Industrial Data Acquisition ADM3491AR Analog Devices 使用用途: Building Automation Networks, Industrial Data Acquisition
What is the ADM3491EARZ?
The ADM3491EARZ is a 3.3 V, full-duplex differential transceiver for TIA/EIA RS-485 and RS-422 communication. According to the Analog Devices ADM3491E product information, it combines a transmitter and receiver, supports multipoint bus transmission lines, provides ±15 kV ESD protection, and operates at up to 12 Mbps. The device is packaged in a 14-pin SOIC for surface-mount industrial and embedded communication designs.
What is the operating voltage of ADM3491EARZ?
The ADM3491EARZ operates from a single 3.3 V supply. The Analog Devices product page describes the ADM3491 as a low-power differential transceiver designed around a single +3.3 V power rail. This makes it suitable for 3.3 V logic systems, but the complete circuit must still provide local supply decoupling and ensure that every connected transceiver operates from a compatible voltage.
Is ADM3491EARZ full duplex or half duplex?
The ADM3491EARZ is a full-duplex RS-485/RS-422 transceiver. According to the Analog Devices ADM3491E family description, its separate transmit and receive paths allow simultaneous bidirectional communication. A full-duplex circuit normally uses two differential signal pairs rather than sharing one pair between the driver and receiver.
What is the maximum data rate of ADM3491EARZ?
The ADM3491EARZ supports a maximum data rate of 12 Mbps. Analog Devices identifies the part as a 3.3 V, ±15 kV ESD-protected full-duplex transceiver rated for 12 Mbps. Actual link performance also depends on cable length, impedance, topology, termination, transceiver loading, and signal-integrity margin, so the 12 Mbps figure should not be interpreted as guaranteed performance for every installed cable.
What is the ESD protection rating of ADM3491EARZ?
The ADM3491EARZ provides ±15 kV ESD protection. The rating is stated by Analog Devices in the product description for the ADM3491E family and is reinforced by the component listing, which identifies the ADM3491EARZ as a 3.3 V, 15 kV ESD-protected RS-485/RS-422 interface IC. The system designer must still provide the intended board-level and cabling protection for the installation environment.
Where can I download the ADM3491EARZ datasheet PDF?
The ADM3491EARZ datasheet is available through Analog Devices' ADM3491E product page and the linked manufacturer documentation. The product page is https://www.analog.com/en/products/adm3491e.html, while the ADM3491 family page is https://www.analog.com/en/products/adm3491.html. Use the manufacturer documents for the complete electrical characteristics, pin description, recommended application circuit, and absolute maximum ratings.
Where can I find the ADM3491EARZ pinout?
The ADM3491EARZ pinout is documented in the manufacturer datasheet's pin-description and typical-application sections. The part uses a 14-pin SOIC package, but pin names and directions should be assigned directly from the Analog Devices pin-description table rather than inferred from another family member. The pinout remains null in the structured data on this page because the pin descriptions were not captured from the datasheet.
What is the difference between ADM3491EARZ and ADM3491AR-1?
The ADM3491EARZ and ADM3491AR-1 are related Analog Devices ADM3491-family transceivers, but their exact electrical deltas should be confirmed from their respective datasheets. The ADM3491EARZ is explicitly listed as the ±15 kV ESD-protected, 3.3 V, full-duplex 12 Mbps member. Before using ADM3491AR-1 as a replacement, verify its package, ESD rating, supply range, enable logic, and full-duplex pin functions.
Can MAX3491CSD+ replace ADM3491EARZ?
MAX3491CSD+ is a cross-brand replacement candidate for ADM3491EARZ because it is associated with the same 14-pin SOIC transceiver format and full-duplex differential-line function. However, a footprint match alone does not guarantee interchangeability. Confirm DE/RE behavior, receiver enable polarity, bus common-mode range, ESD rating, supply limits, and driver output characteristics against both datasheets before production use.
When should I choose ADM3491EARZ over MAX3491ECSD+?
Choose ADM3491EARZ when an established Analog Devices ADM3491E-family design is being maintained and its documented 3.3 V operation, ±15 kV ESD protection, 12 Mbps capability, and DE/RE control are required. Consider MAX3491ECSD+ only after checking that its electrical ratings and enable logic satisfy the existing board. Both parts use a 14-pin SOIC format, but their exact pin-level and transient specifications must be compared.
What is the best drop-in replacement for ADM3491EARZ?
No universally verified drop-in replacement can be selected from package naming alone. ADM3491AR-1, MAX3491CSD+, MAX3491ECSD+, and SP3076EEN-L are candidate replacements associated with the ADM3491EARZ cross-reference, while ADM3491AR belongs to the same manufacturer family. Each candidate requires verification of pin functions, supply voltage, full-duplex operation, DE/RE polarity, ESD rating, and receiver common-mode range.
What can replace ADM3491EARZ?
Potential replacements for ADM3491EARZ include ADM3491AR-1 and ADM3491AR from Analog Devices, plus the cross-brand candidates MAX3491CSD+, MAX3491ECSD+, and SP3076EEN-L. These are 14-pin SOIC-class candidates associated with the target's replacement data, but only a manufacturer-datasheet comparison can confirm true drop-in behavior. Verify every enabled and disabled pin before changing the assembled PCB.
Is ADM3491EARZ suitable for industrial RS-485 communication?
The ADM3491EARZ is suitable for many industrial RS-485 communication systems because it supports a single 3.3 V supply, full-duplex operation, TIA/EIA RS-485 communication, ±15 kV ESD protection, and data rates up to 12 Mbps. Suitability still depends on cable length, topology, surge requirements, grounding strategy, and the operating-temperature rating, which must be checked in the complete manufacturer datasheet.
Where can I buy ADM3491EARZ and what is its lead time?
Use the Request a Quote form on this page to ask about ADM3491EARZ availability, current lead time, minimum order quantity, and delivery options. Analog Devices lists the ADM3491E family as last-time-buy, so supply should be treated as limited rather than assumed to be continuously replenished. The form provides the appropriate commercial response without embedding a potentially stale price or lead-time claim.
What is the price of ADM3491EARZ?
The current commercial price for ADM3491EARZ should be requested through the Request a Quote form on this page. Analog Devices identifies the ADM3491E family as last-time-buy, which can make quantity, condition, and lifecycle availability important purchasing considerations. The form allows the requested quantity and delivery requirements to be reviewed before a supply commitment is made.
Is ADM3491EARZ currently in stock?
Stock status for ADM3491EARZ should be confirmed through the Request a Quote form on this page because the ADM3491E family is listed by Analog Devices as last-time-buy. Last-time-buy status means normal long-term replenishment should not be assumed. Provide the required quantity, shipment destination, and date needed so the available inventory and delivery commitment can be evaluated.
What are the key specifications of ADM3491EARZ that engineers should know?
The key ADM3491EARZ specifications are a 3.3 V single supply, full-duplex RS-485/RS-422 operation, a maximum 12 Mbps data rate, ±15 kV ESD protection, DE/RE control, low-power operation with shutdown, and a 14-pin SOIC package. Analog Devices describes the part as suitable for multipoint bus transmission lines. These points determine interface topology, termination, power design, and candidate-replacement compatibility.

エンジニアリング参考データ: ADM3491EARZ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose ADM3491EARZ for a new or maintained 3.3 V full-duplex RS-485/RS-422 design that requires a documented 12 Mbps capability, ±15 kV ESD protection, DE/RE control, and shutdown operation. ADM3491AR-1 and ADM3491AR are the first same-manufacturer alternatives to evaluate because they belong to the ADM3491 family and use the same 14-SOIC format, but their exact electrical and pin differences must be confirmed. Consider MAX3491CSD+ or MAX3491ECSD+ when their electrical limits align with the target and a second-source policy justifies a cross-brand qualification. SP3076EEN-L is a lower-proximity candidate and should be used only after thorough verification of its pin functions, common-mode range, transient protection, and timing. Because the ADM3491E family is last-time-buy, engineers should also evaluate lifecycle risk and obtain a supply commitment before committing to new production volumes.

代替品との比較

パラメータ この製品 ADM3491AR-1 ADM3491AR MAX3491CSD+ MAX3491ECSD+ SP3076EEN-L
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices MaxLinear
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC

主な差別化要因

  • Documented high-rate full-duplex operation (vs ADM3491AR-1)
  • Explicit ±15 kV ESD-protection positioning (vs MAX3491CSD+)
  • Single 3.3 V power operation with shutdown (vs SP3076EEN-L)

設計ノート

Place the ADM3491EARZ close to the external connector and route the balanced driver and receiver pairs as tightly coupled traces with a continuous reference plane. Keep the differential impedance consistent across the board and avoid routing the bus over split planes or noisy switching-converter areas. Since the device is a 3.3 V full-duplex transceiver, provide local supply decoupling and keep enable-control traces away from the high-speed differential outputs.

Select the signaling rate as a function of total bus length, cable impedance, topology, node count, and the transceiver's receiver and driver characteristics. A 12 Mbps transceiver capability does not guarantee 12 Mbps operation over every cable. Use balanced cable, proper termination at the physical ends of the line, controlled driver transitions, and a common signal-reference path. Verify reflections, attenuation, common-mode range, and logic thresholds using the complete board configuration.

Do not substitute a candidate solely because it uses a 14-pin SOIC footprint. Before replacing ADM3491EARZ, compare DE and RE polarity, receiver enable behavior, shutdown behavior, supply limits, driver-output limits, receiver common-mode range, ESD rating, and every no-connect or alternate-function pin. Also check that the replacement supports the required full-duplex behavior and bus-standard application rather than only offering a similar data rate.

Keep the transceiver's differential traces away from antennas, switching nodes, high-current inductors, and isolated power-converter loops. Maintain a compact ground-return path and use the driver-enable and receiver-enable controls so the unused transmitter is disabled when system timing allows it. When a cable leaves the enclosure, combine appropriate board-level protection with the transceiver's ±15 kV ESD capability; ESD protection does not replace overvoltage, surge, or secondary-protection design.

コンプライアンス情報

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Compliant
紛争鉱物
Unknown

RoHS, REACH, and halogen-free compliance are stated in the component catalog information. AEC-Q100 qualification is not stated and is recorded as not applicable; no separate lead-free or conflict-minerals declaration was available.

データ検証日: 2026-11-19 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

adm3491earz reel7 adm3491earz datasheet ADM3491EARZ datasheet pdf ADM3491EARZ pinout ADM3491EARZ 14-SOIC ADM3491EARZ RS-485 transceiver ADM3491EARZ 3.3V 12Mbps ADM3491EARZ ESD protection ADM3491EARZ equivalent ADM3491EARZ replacement ADM3491EARZ vs MAX3491CSD+ Analog Devices ADM3491EARZ ADM3491EARZ industrial bus ADM3491EARZ price ADM3491EARZ stock

関連部品&用語

Analog Devices ADM3491EARZ ADM3491E ADM3491AR-1 ADM3491AR MAX3491CSD+ MAX3491ECSD+ SP3076EEN-L RS-485 transceiver RS-422 transceiver differential line transceiver interface transceiver balanced differential signaling TIA/EIA RS-485 TIA/EIA RS-422 full duplex DE/RE control 3.3 V power supply 12 Mbps data rate ±15 kV ESD protection shutdown mode 14-SOIC SOIC family surface mount industrial communication
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示