ADS1286PL - 12-Bit 20kHz Micropower ADC | Texas Instruments
部品番号: ADS1286PL ✓ 生産中ADS1286PL 概要
A sampling ADC is a successive-approximation-register, or SAR, converter that acquires an analog voltage with a sample-and-hold circuit and converts it through successive bit decisions. The ADS1286 belongs to the ADC hierarchy within data-converter and signal-chain semiconductors. Its differential input accepts two related analog signals and converts their voltage difference, helping reject common-mode noise when the source is arranged as a bridge, sensor, or instrumentation amplifier.
The device provides 12-bit conversion resolution, a 20kSPS conversion rate, and a serial interface compatible with SPI and SSI protocols. The interface uses either a two-wire or three-wire arrangement described in the manufacturer datasheet. Low 250uA supply consumption is the defining micropower feature, making the converter suitable for battery-operated and remotely powered equipment where each milliampere can influence the enclosure size or service interval.
The ADS1286 uses a sample-and-hold amplifier ahead of the SAR conversion core. The analog input is sampled during the acquisition interval, after which the internal successive-approximation network resolves the sampled voltage to 12 bits. Serial data transfer reduces the number of interconnects required compared with a parallel ADC, although it also makes the host interface timing and signal-integrity design important in systems operating at higher clock rates.
Typical uses include low-frequency pressure and temperature acquisition, low-current battery monitoring, industrial panel controls, portable medical instrumentation, and remote sensor nodes. The 20kSPS rate is appropriate for many slow or medium-bandwidth physical measurements, while the 250uA supply current favors low-duty-cycle acquisition. Differential operation is especially useful when the measured signal is small relative to environmental offsets.
Designers should follow the manufacturer datasheet for input-range, reference, clock, and interface details. Keep analog and digital return paths separated, place input and reference bypass capacitors close to their pins, and account for source impedance during acquisition. The 8-pin PDIP package is through-hole and suits prototypes, legacy industrial equipment, and hand-assembled or leaded-production designs where a surface-mount footprint would be undesirable.
ドロップイン代替品: ADS1286PL — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ADS1286PB
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
ADS1286PL 最大定格&電気的特性
| 分解能 | 12 bit |
| Conversion Rate | 20 kS/s |
| Architecture | Successive-approximation-register, SAR |
| Analog Input Configuration | 1 differential input |
| 電源電圧 | 5 V |
| 電源電流 | 250 uA |
| Serial Interface | SPI and SSI compatible |
| Interface Configuration | 2-wire or 3-wire serial communication |
| Input Stage | Sample-and-hold amplifier |
| パッケージ | 8-pin PDIP |
| 実装タイプ | Through-hole |
| Power Class | Micropower |
ADS1286PL 8-pin pdip ピン配置ガイド
ADS1286PL (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: ADS1286PL.
詳細は データシート をご参照ください。
主な用途
ADS1286PL の用途: 6 件s: Battery-Powered Sensor Nodes, Industrial Pressure and Level Measurement, Portable Medical Instrumentation, Remote Environmental Monitoring, Battery Current and Voltage Monitoring, Legacy Instrumentation and Data Acquisition.
Battery-Powered Sensor Nodes
The ADS1286PL fits remote sensor nodes because its 250uA supply consumption and 12-bit resolution support low-energy measurement without requiring a high-speed converter. The 20kSPS rate is suitable for temperature, pressure, tank level, and other slowly changing physical quantities. A differential input can monitor a bridge or paired sensor outputs while reducing common-mode disturbance. The 5V supply and SPI/SSI-compatible interface simplify connection to a low-power microcontroller. The primary design trade-off is that the sampling architecture requires enough acquisition time for the source impedance, and continuous 20kSPS operation may consume more energy than a duty-cycled acquisition strategy.
おすすめ
Industrial Pressure and Level Measurement
The ADS1286PL is appropriate for industrial pressure, liquid-level, and process monitoring where signals change over a bandwidth well below its 20kSPS conversion rate. Its single differential input can accept the output of an instrumentation amplifier or bridge conditioner, and 12-bit resolution provides 4096 quantization levels. The serial SPI/SSI-compatible interface reduces wiring compared with a parallel ADC. For reliable readings, the conditioning network should keep source impedance within the acquisition limits shown in the manufacturer datasheet. The 8-pin PDIP package also simplifies repair and retrofit work in leaded industrial equipment.
おすすめ
Portable Medical Instrumentation
The ADS1286PL can serve as the acquisition element in compact medical and laboratory instruments measuring slow physiological or analytical signals. Its 12-bit resolution and 20kSPS sampling rate are suitable for selected temperature, pressure, or sensor-interface channels, while 250uA supply current supports battery-oriented operation. Differential input helps when the useful signal is small and appears alongside common-mode voltage. The serial interface occupies fewer host-controller pins than a parallel converter. Medical designs must still evaluate signal isolation, leakage, calibration, safety requirements, and applicable quality procedures independently of the converter's electrical suitability.
おすすめ
Remote Environmental Monitoring
The ADS1286PL is well matched to remote environmental monitoring stations that measure temperature, humidity, soil conditions, or water levels. Its 20kSPS conversion rate is more than sufficient for these slow signals, and the 12-bit result can be sampled periodically to reduce overall system activity. Low 250uA supply current is valuable where the station relies on batteries, solar energy, or infrequent maintenance. The differential input supports balanced sensor arrangements and helps reject common-mode noise. Designers should calculate the complete energy budget, including the ADC, interface, sensor conditioning, and leakage paths, rather than considering converter consumption alone.
おすすめ
Battery Current and Voltage Monitoring
The ADS1286PL can monitor battery voltage, charger current, or a shunt-derived voltage where moderate resolution and low converter power are more important than high-rate waveform capture. Its differential input can measure across a current-sense element while rejecting common-mode voltage, and 20kSPS allows detailed sampling during energy-transfer events. The 12-bit resolution corresponds to 4096 code levels, while 250uA supply consumption minimizes the load introduced by the measurement channel itself. Calibration, shunt resistance, reference stability, and input protection determine practical accuracy more than the nominal converter resolution alone.
おすすめ
Legacy Instrumentation and Data Acquisition
The ADS1286PL suits legacy data-acquisition and laboratory instrumentation where an 8-pin PDIP format simplifies replacement of an existing through-hole board. Its 12-bit resolution and 20kSPS conversion rate cover many general-purpose measurement channels, while the serial interface allows modern firmware to retrieve samples from a compact footprint. The 250uA operating current also benefits portable test equipment. Retrofitting still requires confirmation of pin functions, reference voltage, analog input range, and interface timing against the original schematic and the manufacturer datasheet. A soldered footprint conversion should not be attempted without electrical review.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADS1286PL — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADS1286PB |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit |
| Conversion Rate | 20 kS/s | 20 kS/s |
| Architecture | SAR sampling ADC | SAR sampling ADC |
| Input Configuration | 1 differential input | 1 differential input |
| Supply Voltage | 5 V | 5 V |
| Supply Current | 250 uA | 250 uA |
| Serial Interface | SPI and SSI compatible | SPI and SSI compatible |
| Mounting Type | Through-hole | Through-hole |
主な差別化要因
- Low conversion rate reduces acquisition-system demand (vs ADS1286PB)
- Micropower operation supports portable measurement (vs ADS1286PB)
- Differential acquisition improves signal-chain flexibility (vs ADS1286PB)
設計ノート
Follow the manufacturer recommended application circuit and place input, reference, and bypass capacitors near the associated pins. Keep analog input traces short and avoid routing them beneath digital clock or serial-data paths. For the 8-pin PDIP footprint, observe the package pin-one orientation on the board and use the manufacturer pin-description table as the authority for every net assignment.
The sample-and-hold input must settle sufficiently during each acquisition interval. Verify the worst-case source impedance, output impedance of the sensor or amplifier, and the required settling error using the acquisition-time equations in the manufacturer datasheet. A high source impedance can produce gain errors that appear as inaccurate readings even though the converter itself is functioning correctly.
Do not assume that the differential input accepts arbitrary signals. Confirm the analog input range, common-mode limits, reference arrangement, and absolute maximum ratings before connecting a bridge, shunt, or sensor. The SPI/SSI-compatible interface also requires correct clock polarity, clock phase, data validity timing, and conversion-start behavior for the particular controller implementation.
Estimated: the ADC's stated 250uA supply current at 5V corresponds to approximately 1.25mW of device power consumption, using 5V multiplied by 250uA. Total acquisition-channel power will also include the sensor, interface driver, reference circuitry, leakage paths, and any voltage regulator, so calculate the complete rail budget before assigning battery life.
コンプライアンス情報
Compliance declarations were not established by the manufacturer page or datasheet excerpts used for this product record. Automotive qualification status is also unknown and should not be inferred from the industrial-style package code.