ATF22V10CZ-15JI 10-Macrocell 15ns PLD | Microchip
部品番号: ATF22V10CZ-15JI ✗ 生産終了ATF22V10CZ-15JI 概要
A simple programmable logic device, or SPLD, is a programmable semiconductor that replaces multiple fixed gate-logic packages with one configurable device. Its internal architecture divides a Boolean function into product-term-based macrocells. The ATF22V10CZ architecture extends the generic 22V10 family and supports direct replacement of many 24-pin combinatorial PLDs, placing it within the logic-programmable-device hierarchy of SPLD, complex PLD, and programmable logic technology.
Each of the 10 outputs can be assigned approximately 8 to 16 product terms, and three operating modes are selected automatically by the programming software. The device provides CMOS- and TTL-compatible inputs and outputs, electrically erasable reprogrammable technology, and input transition detection for zero-power operation. A maximum standby power figure of 25 microamperes is specified for the zero-power operating mode.
The ATF22V10CZ/CQZ architecture is designed to implement moderately complex combinational and registered control logic without consuming a programmable FPGA. Maximum pin-to-pin delay is listed at 12 ns for the device family, while the -15 speed designation identifies the 15 ns grade used by this part. Its ten macrocells and ten outputs make it suitable for address decoding, interface control, state-machine next-state logic, and programmable peripheral selection.
Typical uses include industrial control and data-acquisition modules, legacy peripheral expansion, printer and scanner interfaces, instrument front ends, and automated test equipment. The device is also useful when a design requires a small quantity of configurable glue logic while avoiding the development and programming complexity of a larger CPLD.
PCB design should preserve the 28-pin PLCC footprint and allow adequate clearance around the J-leaded terminals for soldering and inspection. Because the operating architecture is configured through software, validate the pin assignments, product-term allocation, and power-up behavior against the manufacturer's pin-description table and device programming requirements before releasing a new layout.
This page combines device specifications, architectural details, application guidance, pin and package constraints, and practical drop-in comparison information. It also identifies the operating features that matter when deciding whether this legacy SPLD remains suitable for a new industrial design or whether a newer programmable-logic device provides a better long-term maintenance path.
ドロップイン代替品: ATF22V10CZ-15JI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ATF22V10CQ-15JI
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ATF22V10C-15JI
✅ ドロップイン価格はお問い合わせください
データシートを見る →ATF22V10CZ-15PJ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
GAL22V10D-10QJ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ATF22V10CZ-15JI 最大定格&電気的特性
| Device Type | Simple Programmable Logic Device (SPLD) |
| Programmable Technology | Electrically Erasable CMOS |
| Macrocells | 10 macrocells |
| Outputs | 10 outputs |
| Product Terms per Output | 8 to 16 product terms |
| Equivalent Logic Gates | 500 gates |
| Speed Grade | 15 ns |
| Maximum Pin-to-Pin Delay | 12 ns |
| 電源電圧 | 5 V |
| Maximum Standby Current | 25 microamperes in zero-power mode |
| Input Compatibility | CMOS and TTL |
| Output Compatibility | CMOS and TTL |
| Operating Modes | 3 software-configured modes |
| Power-Down Feature | Input transition detection with zero-power operation |
| パッケージ | 28-pin PLCC, 11.51 mm x 11.51 mm |
| Terminal Form | J-bend |
| Package Code | QCCJ |
| Package Shape | Square |
| Temperature Grade | Industrial |
| Programming | Electrically erasable and reprogrammable |
ATF22V10CZ-15JI square ピン配置ガイド
ATF22V10CZ-15JI (square パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATF22V10CZ-15JI.
詳細は データシート をご参照ください。
主な用途
ATF22V10CZ-15JI の用途: 6 件s: Industrial Address Decoding, Legacy Peripheral Interface Control, Data-Acquisition Module Control, Printer and Scanner Control Logic, Programmable Test Fixture Sequencing, Legacy Equipment Retrofit and Maintenance.
Industrial Address Decoding
The ATF22V10CZ-15JI suits low- and mid-speed industrial address decoding because it provides 10 macrocells with approximately 8 to 16 product terms per output. A typical circuit assigns separate outputs to memory-select, peripheral-select, interrupt-acknowledge, and chip-enable functions. The 5 V supply and CMOS- or TTL-compatible interfaces allow the PLD to interface directly with many 1980s- and 1990s-era control buses. Its 12 ns maximum family pin-to-pin delay and 15 ns speed grade are adequate for address qualification and access-control timing when the external bus is clocked below the device's capability. Electrically erasable programming also allows decoder logic to be revised without changing the board.
おすすめ
Legacy Peripheral Interface Control
The ATF22V10CZ-15JI is useful for consolidating peripheral interface control into a single configurable device. Its 10 outputs can generate chip selects, read and write strobes, interrupt acknowledgments, and data-direction controls for parallel peripherals. Because the device combines a 5 V supply with CMOS- and TTL-compatible inputs and outputs, it can bridge logic families that would otherwise require several gate packages. The SPLD's software-selected operating modes allow registered or combinational behavior to be assigned as required. In a maintenance-focused system, electrically erasable reprogramming simplifies field updates to timing or interface changes after validation.
おすすめ
Data-Acquisition Module Control
The ATF22V10CZ-15JI can coordinate a multiplexed data-acquisition front end by generating channel-select strobes, sample-and-hold timing, converter enables, and status flags. Its 12 ns maximum family pin-to-pin delay supports control logic operating near the 15 ns grade boundary, although external converters with slower acquisition cycles should dominate the timing budget. The 10-macrocell architecture is sufficient for a compact multiplexer or instrumentation controller rather than a complex digital signal-processing chain. CMOS-compatible inputs and outputs also make it practical to connect to a mixed-signal module while keeping the programmable section separate from sensitive analog paths.
おすすめ
Printer and Scanner Control Logic
The ATF22V10CZ-15JI is well suited to compact printer, scanner, and document-processing mechanisms that require many small control decisions around a shared bus. A single device can implement command decoding, stepper-direction control, motor-enable sequencing, and fault-latch functions without consuming a full FPGA. Its electrically erasable architecture permits firmware-linked logic revisions during product development, while the zero-power input-transition-detection feature can reduce activity when the associated bus is idle. The 28-pin PLCC package also fits established peripheral-control boards that already use this footprint.
おすすめ
Programmable Test Fixture Sequencing
The ATF22V10CZ-15JI can implement the deterministic sequencing and pattern-enable logic found in automated test fixtures. Ten outputs are enough to control relay drivers, fixture banks, measurement gates, and handshake signals, while the product-term architecture handles overlapping test-step conditions. Its 12 ns maximum family pin-to-pin delay and 15 ns speed grade suit low- and medium-speed fixture control rather than high-speed pattern generation. Electrically erasable programming allows test engineers to update step tables and fault-handling logic, and the industrial temperature grade supports use in controlled production or laboratory environments.
おすすめ
Legacy Equipment Retrofit and Maintenance
The ATF22V10CZ-15JI is a practical choice when maintaining an industrial instrument, controller, or peripheral built around the 22V10 PLCC footprint. It can consolidate scattered discrete decode and control gates during a board redesign while preserving established connectors and bus levels. Because the device is electrically erasable, engineers can reproduce and revise the original logic rather than relying on unavailable custom masks. The design decision should still account for the component's legacy technology: verify current sourcing, programming-tool availability, and the manufacturer's lifecycle position before committing it to a long-lived new production run.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATF22V10CZ-15JI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATF22V10CQ-15JI | ATF22V10C-15JI | ATF22V10CZ-15PJ | GAL22V10D-10QJ |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Lattice Semiconductor |
| Package | 28-PLCC (11.51 mm x 11.51 mm) | 28-PLCC (11.51 mm x 11.51 mm) | 28-PLCC (11.51 mm x 11.51 mm) | 28-PLCC (11.51 mm x 11.51 mm) | 28-PLCC (11.51 mm x 11.51 mm) |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| Speed Grade | 15 ns | 15 ns | 15 ns | 15 ns | 10 ns |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Programmable Architecture | 22V10 electrically erasable CMOS architecture with 3 operating modes | 22V10 electrically erasable CMOS architecture | ATF22V10C electrically erasable architecture | 22V10 electrically erasable CMOS architecture | 22V10-class programmable logic architecture |
主な差別化要因
- Closest same-family architecture match (vs GAL22V10D-10QJ)
- Industrial temperature configuration (vs ATF22V10CZ-15PJ)
- Known product-term and operating-mode architecture (vs ATF22V10C-15JI)
設計ノート
Preserve the original 28-pin PLCC land pattern and confirm the terminal pitch against the manufacturer's package drawing. The listed body size of 11.51 mm by 11.51 mm identifies the enclosure, not the solder-mask geometry, so do not derive pad centers from the body dimensions alone. Provide clearance around the J-bent leads for soldering, inspection, and rework, and avoid placing tall heat-sink hardware or enclosure walls over the device.
Use the manufacturer's input and output timing tables to establish setup, hold, and propagation limits for every bus connected to the PLD. The 15 ns speed grade and 12 ns maximum family pin-to-pin delay should be treated as device timing figures, not as a complete system timing budget. Add external filtering where slow or noisy legacy buses attach, and keep clock, chip-select, and data lines away from analog inputs in mixed-signal equipment.
Do not substitute devices solely because the suffix contains 22V10 and 10 macrocells. Verify the 28-pin PLCC package, J-lead form, operating-temperature grade, speed grade, input and output pin functions, and programmer compatibility. A device with a 24-pin SOIC package cannot be soldered onto a PLCC footprint without a board-level redesign, and a 10 ns alternative may require different timing assumptions even when its macrocell count matches.
Design the 5 V supply for both normal operating current and the device's specified input-transition-detection behavior. Place local bypass capacitance close to the supply pins and follow the capacitance and layout recommendations in the manufacturer datasheet. When zero-power operation is used, verify that every connected input has a defined transition state so that an unintended edge cannot wake or disturb the programmed logic.
コンプライアンス情報
The industrial-temperature designation describes the operating grade, not AEC-Q100 automotive qualification. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations appear in the available manufacturer and distributor information for this orderable MPN.