ATMEGA162-16PI - 16MHz AVR MCU, 16KB Flash, 40-PDIP | Microchip
部品番号: ATMEGA162-16PI ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $5.2 | $5.20 |
| 10 | $4.75 | $47.50 |
| 100 | $4.25 | $425.00 |
| 500 | $3.9 | $1,950.00 |
| 1,000 | $3.55 | $3,550.00 |
ATMEGA162-16PI 概要
An 8-bit microcontroller is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as UARTs, timers, and GPIO ports on one die. Within the product hierarchy, the ATmega162 belongs to the AVR ATmega family of flash-based MCUs, which sit under the broader categories of RISC microcontrollers and embedded processors. The AVR architecture executes most of its 131 instructions in a single clock cycle, achieving roughly 1 MIPS per MHz and letting designers trade processing speed directly against power consumption.
Key differentiating features include the dual USART peripherals (rare in this class), JTAG boundary-scan and on-chip-debug support, the 16 KB self-programming flash enabling bootloader-based field updates, and an industrial temperature rating of -40C to +85C indicated by the 'I' suffix. The device also provides two 8-bit timers, one 16-bit timer, four PWM channels, and an 8-channel 10-bit ADC.
Architecturally, the ATmega162 uses an advanced Harvard-structure AVR core with 32 general-purpose working registers fully connected to the ALU, allowing one-cycle execution of register-to-register operations. Fully static operation permits clocking down to DC for ultra-low-power stop modes without register loss.
Typical applications include dual-serial-port industrial controllers, legacy embedded systems where a through-hole 40-pin DIP simplifies prototyping and repair, battery-powered instruments exploiting the low-power idle and power-down modes, and educational platforms.
A key design consideration is clock source selection: the 16 MHz speed grade (16PI) requires a suitable crystal or external clock within fuse-programmed range, and full-speed operation at 16 MHz at -40C to +85C must respect the datasheet derating curve.
This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: ATMEGA162-16PI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATMEGA162-16PI （同一形状・フットプリント） — 相違点: Operating Temperature, Instruction Set, Maximum Clock Frequency, Debug Interface, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
ATMEGA162-16PC
✅ ドロップイン✓ 在庫あり
$1.95 / 個
データシートを見る →ATMEGA162-16PU
✅ ドロップイン✓ 在庫あり
$3.1 / 個
データシートを見る →ATMEGA16-16PI
✅ ドロップイン✓ 在庫あり
$3.72 / 個
データシートを見る →ATMEGA161L-4PI
✅ ドロップイン✓ 在庫あり
$6.35 / 個
データシートを見る →ATMEGA162-16PI 最大定格＆電気的特性
| Core | 8-bit AVR RISC |
| Program Memory Size | 16 KB Flash (8K x 16) |
| SRAM Size | 1 KB |
| EEPROM Size | 512 B |
| 最大クロック周波数 | 16 MHz |
| Maximum Throughput | 16 MIPS at 16 MHz |
| 動作電源電圧 | 4.5 V to 5.5 V |
| 動作温度 | -40C to +85C (industrial, 'I' suffix) |
| パッケージ | 40-PDIP (0.600 in, 15.24 mm) |
| 実装タイプ | Through Hole |
| USART Peripherals | 2 |
| Timers | 2 x 8-bit, 1 x 16-bit |
| PWM Channels | 4 |
| ADC Channels | 8-channel 10-bit |
| JTAG Interface | Yes (on-chip debug and boundary scan) |
| Instruction Set | 131 instructions, most single-cycle |
| In-System Programmable | Yes (self-programming Flash) |
ATMEGA162-16PI 40-pdip (0.600 in, 15.24 mm) ピン配置ガイド
ATMEGA162-16PI (40-pdip (0.600 in, 15.24 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATMEGA162-16PI.
詳細は データシート をご参照ください。
主な用途
ATMEGA162-16PI の用途: 6 件s: Dual-UART Industrial Controllers, Legacy Through-Hole Embedded Systems, Battery-Powered Measurement Instruments, Embedded Education and Prototyping, Motor Control and PWM Systems, Building Automation and Smart Home Nodes.
Dual-UART Industrial Controllers
The ATMEGA162-16PI is one of the few 8-bit AVR MCUs with two independent hardware USARTs, making it a natural fit for controllers that must bridge two serial networks - for example translating between a Modbus RTU field bus and a device-level RS-232 link. Running at 16 MHz, it sustains 16 MIPS, ample headroom for buffered UART handling at 115200 baud on both ports simultaneously. The industrial -40C to +85C temperature rating and 5 V logic tolerance match typical factory-floor electrical environments. Placed between two RS-485 transceivers with the 10-bit ADC monitoring analog setpoints, the part provides a complete single-chip gateway; its self-programming Flash permits field firmware updates over the serial link without a programmer.
おすすめ
Legacy Through-Hole Embedded Systems
The 40-pin 0.600-inch PDIP package of the ATMEGA162-16PI makes it ideal for maintaining and repairing legacy equipment designed when through-hole assembly was standard. The 0.635 mm-pitch leads are hand-solderable and socketable, letting service technicians swap a failed MCU in minutes without hot-air rework. With 16 KB Flash, 1 KB SRAM, JTAG on-chip debugging, and a 16 MHz clock, the part comfortably runs the firmware of mid-1990s to 2000s controllers while offering spare headroom. Its availability in current distribution stock (over 12,000 pieces at Heisener as of September 2026) means long-life industrial machines can keep the original BOM rather than redesigning around a modern SMD MCU.
おすすめ
Battery-Powered Measurement Instruments
The AVR core's fully static operation lets the ATMEGA162-16PI run from DC up to 16 MHz, and its power-down and idle sleep modes reduce average current dramatically in battery instruments such as handheld data loggers and portable meters. Wake-up from power-down via external interrupt or watchdog allows months of standby life, with bursts of full-speed 16 MIPS computation only during measurement cycles. The integrated 8-channel 10-bit ADC digitizes up to eight sensor inputs directly, removing an external converter from the BOM. Designers should note the 4.5 V to 5.5 V supply requirement; a boost converter or four-cell alkaline stack suits this range, and the PWM channels can drive backlight or buzzer outputs.
おすすめ
Embedded Education and Prototyping
Because the ATMEGA162-16PI is a genuine through-hole DIP device, it plugs directly into solderless breadboards and ZIF-socket development boards, making it a favorite for embedded-systems coursework and rapid prototyping. The AVR architecture - 131 mostly single-cycle instructions and 32 general-purpose registers - is straightforward to teach, while the JTAG on-chip-debug interface allows students to single-step code with professional tools rather than relying on printf-style debugging. Its dual USARTs enable labs on serial protocols without software UART bit-banging. ISP programming over a six-wire header keeps the programmer cost minimal, and the 16 KB Flash with self-programming support demonstrates bootloader concepts in a single chip.
おすすめ
Motor Control and PWM Systems
The ATMEGA162-16PI provides four hardware PWM channels driven by its two 8-bit timers and one 16-bit timer, supporting DC motor speed control, servo positioning, and LED dimming at PWM frequencies high enough to avoid audible noise. At a 16 MHz clock the 8-bit timers can generate fast PWM up to roughly 62.5 kHz, and the 16-bit timer delivers fine duty resolution for precision applications. The 10-bit ADC reads feedback from potentiometers, shunt resistors via amplifiers, or temperature sensors to close control loops in firmware, while the industrial temperature rating permits use inside enclosures with elevated ambient temperatures. A gate driver IC should buffer the PWM outputs before driving power MOSFETs.
おすすめ
Building Automation and Smart Home Nodes
For node-level control in building automation - relay switching, damper actuation, occupancy sensing - the ATMEGA162-16PI combines sufficient compute (16 MIPS), analog input (8-channel 10-bit ADC), and dual serial interfaces in one 5 V-tolerant chip. One USART can talk to a room controller over RS-485 while the second services a configuration console or a secondary sensor bus, eliminating software UART overhead. Its 512 B EEPROM stores calibration constants and device addresses that survive power loss and field reconfiguration, and the industrial -40C to +85C rating tolerates unconditioned spaces such as mechanical rooms. Sleep modes keep average consumption low for nodes that wake periodically on interrupts.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATMEGA162-16PI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATMEGA162-16PC | ATMEGA162-16PU | ATMEGA16-16PI | ATMEGA161L-4PI |
|---|---|---|---|---|---|
| Package | 40-PDIP (0.600 in) | 40-PDIP - same | 40-PDIP - same | 40-PDIP - same | 40-PDIP - same |
| Brand | Microchip Technology (Atmel) | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 512 B |
| Max Clock | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 4 MHz |
| USART Count | 2 | 2 | 2 | 1 | 1 |
| Temperature Range | -40C to +85C (industrial) | 0C to +70C (commercial) | Narrower than industrial | -40C to +85C (industrial) | -40C to +85C (industrial) |
| JTAG On-Chip Debug | Yes | Yes | Yes | Yes | No |
主な差別化要因
- Dual hardware USARTs （vs ATMEGA16-16PI)
- Full industrial temperature rating （vs ATMEGA162-16PC)
- JTAG on-chip debug support （vs ATMEGA161L-4PI)
- Trade-off: 5 V only operation （vs Modern 3.3 V MCUs)
設計ノート
The ATMEGA162-16PI requires 4.5 V to 5.5 V supply. Decouple VCC and AVCC separately with 100 nF ceramic capacitors placed within a few millimeters of each pin pair, plus a 10 uF bulk capacitor per board. If using the 10-bit ADC, connect AVCC to VCC through a low-pass LC filter (for example 10 uH + 100 nF) to keep ADC noise low. Brown-out detection should be enabled via fuses at approximately 4.0 V so Flash writes are not corrupted during supply droop.
Fuse configuration is the most common failure point when migrating between ATmega162 variants: wrong clock-source fuses can brick the device to external-clock-only, requiring a high-voltage parallel programmer to recover. Also remember the 16 MHz speed grade guarantees operation only within the specified voltage/temperature envelope; derate clock frequency when operating at reduced VCC. When substituting ATMEGA16-16PI, linkers and interrupt vector tables differ slightly from ATmega162 - recompile firmware rather than re-flashing existing binaries.
Although a through-hole DIP relaxes layout constraints, keep the crystal within 10 mm of XTAL1/XTAL2 with short ground returns for reliable 16 MHz start-up; load capacitors (typically 12-22 pF, per crystal specification) should sit directly at the pins. Route the JTAG header (TDI, TDO, TMS, TCK, plus VCC and GND) to a standard 2x5 header even in production boards - it preserves on-chip debug and boundary-scan access. Provide plated through-holes for all 40 pins; do not rely on press-fit sockets in vibrating environments.
コンプライアンス情報
Compliance status not stated in the retrieved distributor snippets. Request Microchip's official environmental compliance documentation (RoHS/REACH declarations) for the specific purchase lot.
