ATMEGA8L-8MI - 8-Bit 8MHz AVR MCU | Microchip Technology
部品番号: ATMEGA8L-8MI ✓ 生産中ATMEGA8L-8MI 概要
An AVR microcontroller is a compact embedded-control semiconductor that executes instructions from nonvolatile Flash memory and uses SRAM for working data. The ATmega8L family belongs to the 8-bit MCU segment of the broader embedded processor hierarchy. Its mix of digital I/O, serial communications, analog conversion, and modest memory makes it suitable for compact controllers, sensor interfaces, and embedded control products.
Key features include 8KB of self-programming Flash, 512 bytes of EEPROM, and 1KB of internal SRAM. The device provides 130 instructions, eight general-purpose working registers, and an eight-channel 10-bit ADC. I2C supports connection to sensors and configuration devices, SPI supports higher-speed peripherals, and UART/USART enables serial communication with host systems or other embedded controllers.
The ATmega8L-8MI uses the AVR RISC architecture and provides a low-power CMOS implementation suited to embedded control. Its 3V supply requirement supports battery-operated and compact industrial systems. Compared with larger 16- and 32-bit microcontrollers, the device provides a lower-complexity control architecture with limited memory and processing capacity, making firmware design and verification comparatively straightforward.
Typical uses include low-speed sensor hubs, small motor-control boards, industrial interface modules, programmable control panels, and communication bridges. The ADC supports analog monitoring, while the three serial interfaces allow a compact board to connect sensors, storage devices, and service ports without requiring several separate interface components.
Designers should preserve the exposed-pad land pattern and follow the manufacturer's thermal and layout guidance for the 32-VQFN package. Firmware must also account for the ATmega8 and ATmega88 register differences identified in Microchip application note AVR094. Confirm ADC references, clock requirements, and peripheral pin assignments in the ATmega8/L datasheet before PCB release.
This page combines the manufacturer datasheet, distributor package information, practical design guidance, and verified same-footprint replacement information. It also organizes application fit, interface requirements, and migration considerations so engineers can assess the ATMEGA8L-8MI before committing a compact embedded-control design to this device.
ドロップイン代替品: ATMEGA8L-8MI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATMEGA8L-8MI (同一形状・フットプリント) — 相違点: Package, Product Type.
ATMEGA8L-8MU
✅ ドロップイン価格はお問い合わせください
データシートを見る →ATMEGA8L-8MI 最大定格&電気的特性
| Product Type | 8-bit RISC microcontroller |
| Architecture | AVR RISC |
| 最大クロック周波数 | 8 MHz |
| Flash Program Memory | 8 KB |
| Flash Organization | 4K x 16 |
| Internal SRAM | 1 KB |
| EEPROM | 512 bytes |
| ADC Resolution | 10 bits |
| ADC Channels | 8 channels |
| 電源電圧 | 3 V |
| Serial Interfaces | I2C, SPI, UART/USART |
| General-Purpose Registers | 8 registers |
| Instruction Set | 130 instructions |
| パッケージ | 32-VQFN (5x5 mm) |
| Package Type | Quad Flat No-Lead with exposed pad |
| 実装タイプ | Surface mount |
ATMEGA8L-8MI quad flat no-lead with exposed pad ピン配置ガイド
ATMEGA8L-8MI (quad flat no-lead with exposed pad パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATMEGA8L-8MI.
詳細は データシート をご参照ください。
主な用途
ATMEGA8L-8MI の用途: 6 件s: Low-Voltage Sensor Controller, Industrial Interface Module, Small Motor and Actuator Control, Programmable Control Panel, Communication Bridge, Battery-Powered Embedded Device.
Low-Voltage Sensor Controller
The ATMEGA8L-8MI fits a compact 3V sensor controller because its eight-channel 10-bit ADC can monitor several analog inputs while 1KB of SRAM handles short-lived measurement and control data. I2C can connect compatible sensors, and UART/USART can provide a service or data link. The 8KB Flash capacity is adequate for compact acquisition and threshold-control firmware, although designers should reserve space for bootloader functions and confirm the final linked image size.
Industrial Interface Module
A 3V industrial interface module can use the ATMEGA8L-8MI to consolidate protocol conversion, digital inputs, and analog monitoring. I2C supports low-speed embedded peripherals, SPI supports higher-speed devices, and UART/USART handles a host connection without requiring additional interface controllers. The industrial ATmega8L ordering is appropriate where extended-temperature production requirements apply, but the final board must preserve the 32-VQFN exposed-pad layout and follow the manufacturer's layout guidance.
Small Motor and Actuator Control
The ATMEGA8L-8MI can coordinate small motors, relays, and actuators where an 8MHz control rate is sufficient. Its GPIO and timers support deterministic sequencing, while I2C can communicate with sensor or driver ICs and UART/USART can accept higher-level commands. Because the MCU provides no integrated power stage, external transistors or driver circuits remain necessary, and current limits, flyback protection, grounding, and thermal margins should be designed around those external components.
Programmable Control Panel
The ATMEGA8L-8MI can serve as the controller in a compact programmable panel with local inputs, status indication, and a service port. Its 1KB of SRAM is suitable for short command buffers and state variables, while 512 bytes of EEPROM can retain configuration settings. The 10-bit ADC can monitor a potentiometer or sensor, and UART/USART can connect to a host. Firmware size should be checked carefully because the available 8KB of Flash leaves limited space for graphics libraries and extensive protocol stacks.
Communication Bridge
The ATMEGA8L-8MI is useful in a small communication bridge because it combines three serial interfaces—UART/USART, SPI, and I2C—in one controller. A board can translate between a host serial port and a sensor bus, or coordinate a local SPI peripheral while exposing I2C connectivity. At 8MHz, the device is appropriate for modest message rates and control-oriented traffic rather than high-bandwidth protocol bridging, so designers should calculate interrupt load and worst-case serial throughput.
Battery-Powered Embedded Device
The ATmega8L-8MI supports a 3V battery-powered embedded design by combining low-power operation with integrated analog and serial peripherals. The low-power ATmega8L family is suited to intermittent sensing, local threshold decisions, and periodic host communication. The 512-byte EEPROM can preserve limited settings, while sleep-mode behavior and clock configuration can reduce average energy use. Battery life still depends on the external sensor, load-switching circuit, regulator efficiency, and the selected firmware sleep strategy.
エンジニアリング参考データ: ATMEGA8L-8MI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATMEGA8L-8MU |
|---|---|---|
| Package | 32-VQFN (5x5 mm) | 32-VQFN (5x5 mm) |
| Brand | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 8 MHz | 8 MHz |
主な差別化要因
- Exact industrial ATmega8L ordering with integrated mixed-signal peripherals (vs ATMEGA8L-8MU)
- Three serial interfaces consolidated in one 8-bit MCU (vs ATMEGA8L-8MU)
- Compact 5x5 mm surface-mount implementation (vs ATMEGA8L-8MU)
設計ノート
Route the 32-VQFN exposed pad according to the ATmega8/L land-pattern and thermal-via guidance in the manufacturer datasheet. A compliant footprint is essential for assembly and heat transfer. Confirm the exposed-pad net assignment, pad dimensions, solder-mask opening, and via pattern against the current PCB library before release; a visually similar 32-pin QFN footprint may not match the exact body and pad geometry.
Build the 3V power rail with low-noise local decoupling and account for AVR reset requirements during brownout and power-up. Follow the datasheet's recommended capacitor values and placement, including the separation between regulator output and the MCU supply pins. Estimate the board's peak current before choosing the regulator so the ADC, communications peripherals, external loads, and capacitor charging do not create supply droop during startup.
Do not treat ATmega8 and ATmega88 as register-compatible without review. Microchip application note AVR094 identifies I/O registers whose functions differ and provides a migration table. Before substituting an ATmega88-family device, map interrupt vectors, timer registers, ADC behavior, port functions, and fuse settings, then recompile and retest the application rather than changing only the device marking.
Keep analog inputs away from fast-switching nets and route them over a continuous ground reference. The ADC uses 10-bit resolution, but practical accuracy still depends on reference-voltage stability, source impedance, sampling time, and layout. Use the datasheet's ADC input guidance and consider local reference filtering when measuring low-amplitude or high-source-impedance signals.
コンプライアンス情報
The industrial identifier is part of the ordering information for ATMEGA8L-8MI. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was included in the cited product records, so these fields remain unknown.