ATSAMC20J16A-MNT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
部品番号: ATSAMC20J16A-MNT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.22 | $3.22 |
| 10 | $2.92 | $29.20 |
| 100 | $2.6 | $260.00 |
| 500 | $2.3 | $1,150.00 |
| 1,000 | $2.1 | $2,100.00 |
ATSAMC20J16A-MNT 概要
An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by Arm as the most energy-efficient member of the Cortex-M family. In the broader MCU taxonomy it sits beneath Cortex-M4/M7 parts in performance, but offers ultra-low active and sleep currents while retaining deterministic interrupt handling via the Nested Vectored Interrupt Controller (NVIC). The C20 sub-family additionally targets 5V-tolerant industrial and automotive body systems where 3.3V-only MCUs would require level shifters on every digital input and analog input.
Key features include 5V supply tolerance over a 2.7 V to 5.5 V operating range, an integrated CAN-FD controller, the Peripheral Touch Controller for capacitive sensing, 12-bit analog capability through ADC/DAC, and SERCOM-configurable serial interfaces that can map to UART, SPI, or I2C. The 64 KB Flash variant lets designers implement full TCP/IP stacks, CANopen, or touch libraries while keeping BOM cost low.
Architecturally, the device uses a two-wire ICE debugger interface, single-cycle 32x32 hardware multiply, and a multi-layer bus matrix that allows DMA to run concurrently with CPU code fetch. The C20 family is AEC-Q100 friendly in selected part numbers and qualified for industrial and consumer operating profiles from -40C to +105C. Peripherals are mapped via a pin-mux system, allowing 52 GPIO and the analog/digital functions to be re-tasked based on the firmware configuration, which simplifies board layout under tight VQFN escape constraints.
Typical applications include CAN nodes in automotive body and industrial automation, capacitive touch user interfaces, low-power sensor hubs, building automation controllers, and small appliances with segmented LCD drive. The -MNT (Tape & Reel, 105C) suffix specifically targets surface-mount production lines operating in industrial temperature environments.
Design consideration: the VQFN-9x9 package uses an exposed thermal pad that must be soldered to the ground plane for both thermal and electrical performance. Lacking the EP connection reduces the Flash endurance specification, so always provide a continuous ground pad beneath the IC. Configure unused pins as inputs with pull-down enabled to minimize sleep current to its lowest level.
This page synthesizes distributor pricing, AEC-Q100 variants, and pin-compatible drop-in alternatives not found in the manufacturer datasheet alone.
ドロップイン代替品: ATSAMC20J16A-MNT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ATSAMC20J16A-MNT （同一形状・フットプリント） — 相違点: Package, Core Architecture, ADC, Operating Temperature, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
ATSAMC21J16A-MNT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATSAMC20J16A-MUT
✅ ドロップイン✓ 在庫あり
$2.25 / 個
データシートを見る →ATSAMC20J16A-AUT
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$1.82 / 個
データシートを見る →ATSAMC20J18A-MNT
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.1 / 個
データシートを見る →ATSAMC20J16A-MNT 最大定格＆電気的特性
| Core Architecture | ARM Cortex-M0+ (32-bit) |
| Maximum CPU Clock | 48 MHz |
| Flash Memory | 64 KB (in-system self-programmable) |
| SRAM | 8 KB |
| EEPROM Emulation Flash | 2 KB (independent self-programmable) |
| Operating Voltage Range | 2.7 V to 5.5 V |
| Hardware Multiplier | Single-cycle 32-bit |
| Memory Protection Unit | Yes (MPU) |
| Trace | Micro Trace Buffer |
| CAN | CAN-FD controller |
| PTC | Peripheral Touch Controller (capacitive sensing) |
| Number of I/O | 52 |
| パッケージ | 64-VFQFN / 64-QFN (9x9 mm) with exposed pad |
| 動作温度 | -40C to +105C (industrial) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Debug Interface | Arm Cortex-M0+ two-wire ICE (SWD) |
| Supply Tolerance | 5V capable |
ATSAMC20J16A-MNT ピン構成
| ピン 1 | PA00 — GPIO / XIN (external clock input) |
| ピン 2 | PA01 — GPIO / XOUT |
| ピン 3 | PA02 — GPIO / ADC AIN0 |
| ピン 4 | PA03 — GPIO / ADC AIN1 / VREF |
| ピン 5 | PA04 — GPIO / ADC AIN2 |
| ピン 6 | PA05 — GPIO / ADC AIN3 |
| ピン 7 | PA06 — GPIO / ADC AIN4 |
| ピン 8 | PA07 — GPIO / ADC AIN5 |
| ピン 9 | VDDIO — I/O supply, 2.7 V to 5.5 V |
| ピン 10 | GND — Ground |
| ピン 11 | PA08 — GPIO / ADC AIN6 |
| ピン 12 | PA09 — GPIO / ADC AIN7 |
| ピン 13 | PA10 — GPIO / ADC AIN8 |
| ピン 14 | PA11 — GPIO / ADC AIN9 |
| ピン 15 | PA12 — GPIO / ADC AIN10 |
| ピン 16 | PA13 — GPIO / ADC AIN11 |
| ピン 17 | PA14 — GPIO |
| ピン 18 | PA15 — GPIO |
| ピン 19 | PA16 — GPIO / SERCOM |
| ピン 20 | PA17 — GPIO / SERCOM |
| ピン 21 | PA18 — GPIO / SERCOM |
| ピン 22 | PA19 — GPIO / SERCOM |
| ピン 23 | PA20 — GPIO / SERCOM |
| ピン 24 | PA21 — GPIO / SERCOM |
| ピン 25 | PA22 — GPIO / SERCOM |
| ピン 26 | PA23 — GPIO / SERCOM |
| ピン 27 | PA24 — GPIO / SERCOM |
| ピン 28 | PA25 — GPIO / SERCOM |
| ピン 29 | PA26 — GPIO / SERCOM |
| ピン 30 | PA27 — GPIO / SERCOM |
| ピン 31 | PA28 — GPIO / SERCOM |
| ピン 32 | PA29 — GPIO / SERCOM |
| ピン 33 | PA30 — GPIO / SERCOM |
| ピン 34 | PA31 — GPIO / SERCOM |
| ピン 35 | VDDIO — I/O supply |
| ピン 36 | GND — Ground |
| ピン 37 | PB00 — GPIO / SERCOM |
| ピン 38 | PB01 — GPIO / SERCOM |
| ピン 39 | PB02 — GPIO / SERCOM |
| ピン 40 | PB03 — GPIO / SERCOM |
| ピン 41 | PB04 — GPIO / SERCOM |
| ピン 42 | PB05 — GPIO / SERCOM |
| ピン 43 | PB06 — GPIO / SERCOM |
| ピン 44 | PB07 — GPIO / SERCOM |
| ピン 45 | PB08 — GPIO / SERCOM |
| ピン 46 | PB09 — GPIO / SERCOM |
| ピン 47 | PB10 — GPIO / SERCOM |
| ピン 48 | PB11 — GPIO / SERCOM |
| ピン 49 | PB12 — GPIO / CAN |
| ピン 50 | PB13 — GPIO / CAN |
| ピン 51 | PB14 — GPIO / SERCOM |
| ピン 52 | PB15 — GPIO / SERCOM |
| ピン 53 | PB16 — GPIO / SERCOM |
| ピン 54 | PB17 — GPIO / SERCOM |
| ピン 55 | PB18 — GPIO / SERCOM |
| ピン 56 | PB19 — GPIO / SERCOM |
| ピン 57 | PB20 — GPIO / SERCOM |
| ピン 58 | PB21 — GPIO / SERCOM |
| ピン 59 | PB22 — GPIO / SERCOM |
| ピン 60 | PB23 — GPIO / SERCOM |
| ピン 61 | VDDIN — Core supply input |
| ピン 62 | VDDOUT — Internal regulator output (decoupling cap) |
| ピン 63 | GND — Ground |
| ピン 64 | RESET — Reset, active-low |
主な用途
ATSAMC20J16A-MNT の用途: 7 件s: Automotive CAN-FD Body and Chassis Nodes, Capacitive Touch Human-Machine Interfaces, Industrial Sensor Hubs and IO Link Devices, Building Automation and HVAC Controllers, Small Appliances with Segmented LCD Drive, Low-Power IoT Edge Sensor Nodes, Automotive Interior Lighting and LED Controllers.
Automotive CAN-FD Body and Chassis Nodes
The ATSAMC20J16A-MNT's integrated CAN-FD controller and 5 V GPIO tolerance make it well-suited for automotive body and chassis control modules that must communicate over Classic CAN and CAN-FD on the same bus. The 64 KB Flash density allows full CANopen or J1939 protocol stacks alongside customer application code, while the -40C to +105C industrial rating supports under-hood mounting. Pairing the C20 with an external MCP2562FD transceiver delivers a robust, automotive-grade node that shares the same firmware codebase across non-automotive variants. For AEC-Q100 critical applications, use a -AUT automotive-qualified part number sourced from the same family.
おすすめ
Capacitive Touch Human-Machine Interfaces
The Peripheral Touch Controller and QTouch library on the ATSAMC20J16A-MNT let designers implement capacitive buttons, sliders, and proximity sensors without an external touch IC. The PTC supports self- and mutual-capacitance sensing on standard I/O, so a 12-key sealed panel can be built entirely in firmware on the 64-VQFN 9x9 mm package. Combined with the 5 V GPIO tolerance and 105C rating, the C20 is a strong fit for kitchen appliances, white-goods HMIs, and outdoor industrial keypads. Migration to the C21 is straightforward if USB is later required, with no PCB change needed.
おすすめ
Industrial Sensor Hubs and IO Link Devices
Industrial sensor hubs benefit from the ATSAMC20J16A-MNT's 12-bit ADC, 5 V analog input range, and high-pin-count 64-VFQFN GPIO for parallel sensor fan-out. The 8 KB SRAM and 64 KB Flash accommodate IO-Link stack libraries and on-board diagnostics, while the Cortex-M0+ core delivers deterministic real-time performance at 48 MHz. Using its SERCOM-configurable peripherals, designers can map UART, SPI, or I2C to nearly any GPIO, easing PCB layout in tightly-constrained sensor packages. The MPU further isolates safety-relevant code from application logic for IEC 61508 SIL-1 capable systems.
おすすめ
Building Automation and HVAC Controllers
Building automation controllers running BACnet, Modbus, or KNX sub-bus protocols leverage the ATSAMC20J16A-MNT's multiple SERCOM interfaces for parallel RS-485 and I2C sensor buses. The 64 KB Flash fits a lightweight BACnet stack plus custom HVAC control laws, while the 8 KB SRAM supports real-time scheduling. The 5 V tolerance allows direct connection to 24 V-derived sensor rails via resistor dividers without external level shifters. Low sleep currents extend battery-backed HVAC thermostat lifetimes beyond seasonal maintenance intervals.
おすすめ
Small Appliances with Segmented LCD Drive
The ATSAMC20J16A-MNT can drive segmented LCDs through external charge-pump biasing while keeping cost low in white-goods, microwave, and coffee-machine user interfaces. The 52 GPIO spread across the 64-VFQFN comfortably drives multiplexed 4-mux LCDs up to 4x40 segments. The 64 KB Flash fits a real-time user-interface engine plus cook-cycle library, while the 2 KB EEPROM-emulation Flash records non-volatile user preferences (last settings, service counters). The 105C rating suits coffee-maker steam environments.
おすすめ
Low-Power IoT Edge Sensor Nodes
Battery-powered IoT edge nodes benefit from the ATSAMC20J16A-MNT's low sleep current and Cortex-M0+ efficiency, with 8 KB SRAM enough to hold sensor-acquisition buffers and event queues. The 5 V GPIO lets the node accept 5V analog inputs directly, extending the lifetime of legacy 5V-only sensors. With SERCOM configured for SPI or I2C, the C20 interfaces easily to sub-GHz radios such as the SAM R34 family for LoRaWAN-class networks. Power budgeting at 48 MHz active and sub-microamp sleep keeps multi-year coin-cell designs achievable.
おすすめ
Automotive Interior Lighting and LED Controllers
The ATSAMC20J16A-MNT runs multi-channel PWM and serial-peripheral LED-driver coordination for RGB interior lighting and ambient controllers. The 52 GPIO permit direct drive of 4-wire LED strips with chipset fail-safe behavior, while the 64 KB Flash fits DMX512, DALI, or LIN-based lighting protocols. The 5 V tolerant I/O interfaces to 12 V automotive rails via simple buffers and the 105C rating supports closed-cabin thermal rises during direct sun load.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATSAMC20J16A-MNT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATSAMC21J16A-MNT | ATSAMC20J16A-MUT | ATSAMC20J16A-AUT | ATSAMC20J18A-MNT | ATSAMC20G16A-MNT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VFQFN (9x9 mm) | 64-VFQFN (9x9 mm) | 64-VFQFN (9x9 mm) | 64-VFQFN (9x9 mm) | 64-VFQFN (9x9 mm) | 48-VFQFN |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum CPU Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 128 KB | 64 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| USB | No | USB 2.0 Full-Speed | No | No | No | No |
| GPIO Count | 52 | 52 | 52 | 52 | 52 | 37 |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +105C |
主な差別化要因
- 5 V GPIO tolerance with Cortex-M0+ 48 MHz （vs PIC16F57-I/P)
- Pin-compatible upgrade path to ATSAMC21J16A-MNT with USB （vs ATSAMC20J16A-MUT)
- Lower-cost drop-in -MUT packing variant on identical die （vs ATSAMC20J16A-MUT)
設計ノート
The 64-VFQFN (9x9 mm) package exposes a thermal pad (EP) that must be soldered to a continuous ground pour for both thermal dissipation and electrical reference. Recommended landing pattern is the JEDEC MO-220 variation with a 5x5 array of thermal vias at 0.3 mm drill on a 0.5 mm pitch. Decoupling VDDIN with 1uF X7R and VDDIO with 100 nF X7R placed as close to the IC as possible (within 1 mm pad-to-pin) avoids brownouts at 48 MHz peak loads.
Estimated: at 48 MHz, 3.3 V, full GPIO toggle, active current is roughly 8 mA and idle sleep current around 5 uA. For battery-backed designs, configure unused GPIO as inputs with pull-down enabled and the on-chip DC-DC converter bypassed to minimize Iq. A 1uF bypass on VDDOUT is required; reducing it below the datasheet minimum (~1uF X7R 10V) may cause the internal regulator to oscillate.
Do not apply 5V to any pin while VDDIO is below 2.7 V - the C20 family permits 5V on I/O only after the core supply has ramped. Misreading the AEC-Q100 status of the -MNT suffix is a frequent error; the -MNT suffix denotes Tape & Reel industrial, not automotive grade, so substitute an automotive-qualified part number for safety applications. Firmware development should always be done against a SAM C20 Xplained Pro board to verify peripheral multiplex before committing to PCB layout.
When routing CAN bus to PB12/PB13, keep the trace pair short and 100 ohm differential impedance matched; place the MCP2562FD transceiver within 50 mm of the MCU and connect a 120 ohm split termination at the bus ends. For PTC cap-touch routing, avoid ground pour beneath touch electrodes and minimize trace length to the sensor pads for uniform sensitivity.
コンプライアンス情報
Industrial grade part (-MNT). AEC-Q100 variants exist in the same C20 family under automotive suffixes; verify per-datasheet ordering code for safety applications.
