ATSAMD09D14A-MUT - 48MHz Cortex-M0+ MCU, 16KB Flash | Microchip
部品番号: ATSAMD09D14A-MUT ✓ 生産中ATSAMD09D14A-MUT 概要
What is a Cortex-M0+ microcontroller? A Cortex-M0+ MCU is a 32-bit ARM microcontroller core designed for low power, low cost, and deterministic interrupt response. It sits below Cortex-M3/M4 in the ARM taxonomy and is widely used as a system management controller, sensor hub, or low-power main controller. The SAM D09D family specifically targets reduced-feature, small-pincount designs that need linear address map and hex-compatible code with the rest of the SAM D portfolio for migration.
Key features of the ATSAMD09D14A-MUT include a 48 MHz maximum CPU clock delivering 2.46 CoreMark/MHz, peripheral touch controller support, multiple low-power sleep modes, and on-chip SERCOM (serial communication) modules. The 24-QFN (4x4) footprint keeps the PCB area under 16 mm², making it suitable for space-constrained sensor modules and wearable reference designs.
Architecturally, the device uses a single-cycle I/O bus and a low-latency interrupt controller. The integrated voltage regulator supports 1.62V to 3.63V operation across industrial temperature ranges, simplifying battery-powered designs where a single Li-ion or 2xAA cell must be tolerated. The 2.46 CoreMark/MHz efficiency translates to roughly 118 CoreMark at full clock, competitive for the M0+ tier.
Typical applications include smart-home sensor nodes, low-power wireless companion MCUs, IoT end nodes, smart metering endpoints, and human-machine interface buttons using built-in touch support. Code migration from D10/D11/D20/D21 SAM D parts is supported through hex-compatible linear address mapping.
When designing, ensure the QFN thermal pad is soldered to a sufficient copper pour for heat spreading and that decoupling capacitors are placed within 2 mm of the supply pins. The internal regulator and brown-out detector should be configured via fuse bits during production programming.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design considerations not collected in the manufacturer summary datasheet.
ドロップイン代替品: ATSAMD09D14A-MUT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ATSAMD09C13A-MUT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAMD09D14A-MU
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ATSAMD09D14A-MNT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAMD10D14A-MUT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAMD11D14A-MUT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAMD20D14A-MUT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATSAMD09D14A-MUT 最大定格＆電気的特性
| Core | ARM Cortex-M0+ (32-bit) |
| Family | SAM D09D (Atmel SMART SAM D) |
| Maximum CPU Frequency | 48 MHz |
| CoreMark/MHz | 2.46 |
| Flash Memory | 16 KB (16K x 8) |
| SRAM | 4 KB |
| Operating Voltage Range | 1.62 V to 3.63 V |
| I/O Pins | GPIO (per datasheet, exact count not in summary) |
| パッケージ | 24-pin QFN (4x4 mm) with exposed pad |
| 実装タイプ | Surface Mount |
| 動作温度範囲 | -40C to +85C (industrial, per Microchip SAM D family convention) |
| Peripherals | SERCOM, Peripheral Touch Controller, ADC (per SAM D09 feature set) |
| Code Migration | Pin-compatible and hex-compatible with SAM D10/D11/D20/D21 family |
| MSLレベル | MSL3 (per QFN package handling, verify on label) |
| RoHS ステータス | Compliant |
ATSAMD09D14A-MUT ピン構成
| ピン 1 | PA02 — GPIO / peripheral function via PORT mux (ADC, SERCOM) |
| ピン 2 | PA03 — GPIO / peripheral function via PORT mux |
| ピン 3 | PA04 — GPIO / peripheral function via PORT mux |
| ピン 4 | PA05 — GPIO / peripheral function via PORT mux |
| ピン 5 | PA06 — GPIO / peripheral function via PORT mux |
| ピン 6 | PA07 — GPIO / peripheral function via PORT mux |
| ピン 7 | VDD — Digital supply input |
| ピン 8 | GND — Ground |
| ピン 9 | PA08 — GPIO / peripheral function via PORT mux |
| ピン 10 | PA09 — GPIO / peripheral function via PORT mux |
| ピン 11 | PA10 — GPIO / peripheral function via PORT mux |
| ピン 12 | PA11 — GPIO / peripheral function via PORT mux |
| ピン 13 | PA14 — GPIO / peripheral function via PORT mux |
| ピン 14 | PA15 — GPIO / peripheral function via PORT mux |
| ピン 15 | PA16 — GPIO / peripheral function via PORT mux |
| ピン 16 | PA17 — GPIO / peripheral function via PORT mux |
| ピン 17 | PA18 — GPIO / peripheral function via PORT mux |
| ピン 18 | PA19 — GPIO / peripheral function via PORT mux |
| ピン 19 | PA22 — GPIO / peripheral function via PORT mux |
| ピン 20 | PA23 — GPIO / peripheral function via PORT mux |
| ピン 21 | PA24 — GPIO / peripheral function via PORT mux |
| ピン 22 | PA25 — GPIO / peripheral function via PORT mux |
| ピン 23 | RESET — Reset input, active-low |
| ピン 24 | EP — Exposed pad - thermal and ground, must be soldered to PCB pour |
主な用途
ATSAMD09D14A-MUT の用途: 7 件s: Smart Home Sensor Hub, Industrial Metering Endpoints, Consumer Appliance HMI, Wearable Health Patches, IoT Wireless Companion MCU, Battery-Powered LED Lighting Controllers, Portable Barcode / RFID Scanners.
Smart Home Sensor Hub
The ATSAMD09D14A-MUT is well-suited as the main controller for battery-powered smart-home sensor hubs because of its 48 MHz Cortex-M0+ core, 4 KB SRAM, and 1.62-3.63 V wide supply range that supports a single CR2032 or 2xAA cell stack. The 24-QFN 4x4 mm package enables compact PCB integration alongside Zigbee, BLE, or LoRa modules. The peripheral touch controller and SERCOM instances handle capacitive buttons and UART/I2C sensor polling efficiently. Estimated active current stays in the single-digit mA range at 48 MHz, and the deep-sleep modes drop below 1 uA, extending battery life across multi-year deployments.
おすすめ
Industrial Metering Endpoints
For water, gas, and electricity metering endpoints, the ATSAMD09D14A-MUT delivers the deterministic interrupt response and 48 MHz performance needed for accurate pulse counting and sensor sampling. Its 16 KB Flash accommodates metering protocol stacks (Modbus, Wireless M-Bus framing) while 4 KB SRAM handles rolling consumption buffers. The industrial -40C to +85C temperature range supports outdoor meter enclosures. Pin-compatibility with the SAM D20/D21 family allows painless migration to higher-memory variants for advanced metering infrastructure (AMI) features such as DLMS/COSEM.
おすすめ
Consumer Appliance HMI
Consumer appliances such as coffee machines, air purifiers, and induction cooktops benefit from the ATSAMD09D14A-MUT's peripheral touch controller for capacitive buttons and sliders, replacing mechanical switches that wear out. The 48 MHz Cortex-M0+ performance drives small TFT or segment LCDs, manages PWM for motor control, and communicates via UART or I2C to sensor packs. The 24-QFN 4x4 mm footprint fits tight HMI board layouts and the industrial temperature grade handles kitchen and laundry environments. Code migration to SAM D11 adds USB host for diagnostic ports.
おすすめ
Wearable Health Patches
Wearable health patches leverage the ATSAMD09D14A-MUT's low-power architecture and small 24-QFN 4x4 mm footprint for unobtrusive skin-mounted designs. The 1.62-3.63 V supply accepts single Li-ion or coin-cell batteries directly, while deep-sleep currents below 1 uA extend patch wear-time to 7-14 days. The 16 KB Flash is sufficient for heart-rate, SpO2, or temperature processing firmware and 4 KB SRAM buffers sensor sample streams. The Cortex-M0+ deterministic interrupt latency ensures reliable BLE radio timing when paired with an external transceiver.
おすすめ
IoT Wireless Companion MCU
As an IoT wireless companion MCU alongside a primary radio SoC, the ATSAMD09D14A-MUT manages sensor aggregation, secure element interfacing, and low-power wake-up duties. The 48 MHz performance and SERCOM modules (UART, I2C, SPI) easily handle multi-sensor I/O expansion. Its pin-compatible migration path to ATSAMD11D14A-MUT adds USB 2.0 Full-Speed for direct PC connectivity in firmware update modes. The 24-QFN footprint occupies minimal board area when stacked beneath a host SoM module.
おすすめ
Battery-Powered LED Lighting Controllers
LED lighting controllers for landscape, signage, and architectural applications use the ATSAMD09D14A-MUT to generate multi-channel PWM dimming and color-mixing sequences at low power. The 48 MHz Cortex-M0+ provides precise PWM resolution and the SERCOM blocks drive addressable LED strips (WS2812, SK6812) via SPI or bit-banged UART. Wide 1.62-3.63 V supply range accepts 2xAA or LiFePO4 batteries directly. The 24-QFN 4x4 mm package keeps driver PCBs compact enough to fit inside linear fixture housings and the industrial temperature grade handles outdoor enclosures.
おすすめ
Portable Barcode / RFID Scanners
Portable barcode and RFID scanners benefit from the ATSAMD09D14A-MUT's deterministic Cortex-M0+ interrupts, which minimize decode latency for 1D/2D imagers. The 4 KB SRAM buffers scan-image processing and 16 KB Flash stores decoders for common symbologies. The 1.62-3.63 V supply range accepts single-cell Li-ion packs and the deep-sleep modes extend standby time during shift work. Pin-compatibility with the SAM D11 family allows upgrades to USB-C host stacks without PCB rework.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATSAMD09D14A-MUT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATSAMD09C13A-MUT | ATSAMD10D14A-MUT | ATSAMD11D14A-MUT | ATSAMD20D14A-MUT | ATSAMD09D14A-MU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-QFN (4x4 mm) | 24-QFN (4x4 mm) - same | 24-QFN (4x4 mm) - same | 24-QFN (4x4 mm) - same | 24-QFN (4x4 mm) - same | 24-QFN (4x4 mm) - same |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Max CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 16 KB | 8 KB (-50%) | 16 KB | 16 KB | 16 KB | 16 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 2 KB (-50%) | 4 KB |
| Operating Voltage | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| USB 2.0 Support | No | No | No | Yes (FS USB) | No | No |
主な差別化要因
- Reduced-feature 16 KB / 4 KB Cortex-M0+ in 24-QFN （vs ATSAMD20D14A-MUT)
- Pin-and-hex compatible with full SAM D family （vs NXP KL03Z16VFK4)
- No USB - lower BOM cost vs D11 （vs ATSAMD11D14A-MUT)
設計ノート
Estimated: the ATSAMD09D14A-MUT QFN-24 exposed thermal pad has theta_JA approximately 35-40 C/W on a standard 4-layer JEDEC EIA/JESD51 test board. At typical Cortex-M0+ workloads (10-20 mA active supply) the junction temperature rise stays under 5 C above ambient, so no external heatsink is required. The exposed pad must be soldered to a continuous copper pour with at least 8 thermal vias to a ground plane for proper heat spreading and electrical reference.
Place the 0.1 uF VDD decoupling capacitor within 2 mm of the VDD pin (pin 7) with a short, wide trace to ground. Add a 1 uF bulk capacitor on the same rail close to the MCU. For SERCOM signals above 1 MHz, route traces over a continuous ground reference and keep trace lengths matched within 5 mm to avoid skew. Avoid routing GPIO traces under the exposed pad to prevent solder-wicking shorts during reflow.
Do not exceed the absolute maximum VDD rating of 3.63 V (per SAM D09 family datasheet); transients above this can permanently damage the on-chip voltage regulator. Configure the brown-out detector (BOD33) fuse bits during production programming to enable safe reset behavior below 1.62 V. When migrating from SAM D09 to SAM D20/D21, verify SRAM sizing - the SAM D20D14A variant has only 2 KB SRAM compared to the 4 KB on SAM D09, which may force buffer redesign.
コンプライアンス情報
RoHS and REACH compliance inferred from Microchip product page and distributor listings. Halogen-free status not explicitly confirmed in summary datasheet - refer to full datasheet or manufacturer declaration. AEC-Q100 not applicable for industrial-grade part; check automotive-grade variants for vehicle applications.
