ATTINY25-20MF - 20MHz 8-Bit AVR Microcontroller | Microchip
部品番号: ATTINY25-20MF ✓ 生産中ATTINY25-20MF 概要
An 8-bit microcontroller is a programmable integrated circuit that executes instructions using an 8-bit data path. Microcontrollers combine a processor core, nonvolatile program memory, working memory, and peripherals into one device. Within the broader semiconductor hierarchy, the ATTINY25 belongs to the AVR family of reduced-instruction-set computers and to the TinyAVR segment of small, low-power embedded controllers. This makes it suitable for local control logic where a larger processor would add unnecessary cost, power, and board area.
The ATTINY25-20MF combines 2 KB of ISP Flash with 128 bytes of EEPROM and 128 bytes of SRAM. Its 20 MHz AVR core provides substantially more operating headroom than the 10 MHz figure appearing in one retailer listing, while the manufacturer identifies the family as a picoPower AVR RISC-based CMOS device. Six general-purpose I/O lines support digital sensing, switching, and signaling, while the integrated 8-bit timer/counter with compare modes is useful for periodic events, timing, and basic waveform generation.
Program development follows the AVR embedded workflow through Microchip's programming and debug ecosystem. In-System Programming and ICSP permit firmware to be loaded and updated without removing the device from its circuit, while the manufacturer documents programming through an 8-pin SIL connector using two I/O signals and the reset line. The 32 working registers support efficient instruction execution, and the dedicated Flash, SRAM, and EEPROM regions allow firmware code, temporary state, and retained configuration data to occupy separate memories.
Typical applications include compact sensor interfaces, LED status and control nodes, simple motor or valve controllers, industrial automation modules, battery-powered accessories, and small consumer products. The six I/O lines and 8-bit timer are especially useful in designs where a small state machine reads inputs and drives outputs without requiring a high-performance application processor. Its small QFN footprint also supports dense modules and compact control boards.
PCB implementation requires careful attention to the exposed thermal pad, power and ground connectivity, and programming access. Place the device's decoupling capacitor close to its supply pins, connect the exposed pad to the ground plane according to the manufacturer land pattern, and preserve access to the ICSP interface. Confirm the exact pin mapping and exposed-pad geometry against the manufacturer datasheet before releasing artwork.
This product page combines the manufacturer architecture description with exact ordering, package, memory, and interface details, then adds practical programming, layout, replacement, and comparison guidance for engineers evaluating the ATTINY25-20MF in embedded control designs.
ドロップイン代替品: ATTINY25-20MF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ATTINY25-20MFR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ATTINY25-20MF 最大定格&電気的特性
| Core Processor | 8-bit AVR RISC |
| 最大クロック周波数 | 20 MHz |
| Flash Memory | 2 KB in-system programmable Flash |
| Flash Organization | 1K x 16 bits |
| EEPROM | 128 bytes |
| SRAM | 128 bytes |
| General-Purpose I/O Lines | 6 lines |
| General-Purpose Working Registers | 32 registers |
| Timer/Counter | 1 8-bit timer/counter with compare modes |
| パッケージ | 20-QFN-EP, 4 x 4 mm |
| Package Pin Count | 20 pins |
| 実装タイプ | Surface mount, no lead |
| Programming | In-System Programming and ICSP |
| Architecture | picoPower AVR CMOS 8-bit |
| Series | ATtiny, Functional Safety (FuSa) tinyAVR |
| ライフサイクル状態 | Active |
ATTINY25-20MF 20 pins ピン配置ガイド
ATTINY25-20MF (20 pins パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATTINY25-20MF.
詳細は データシート をご参照ください。
主な用途
ATTINY25-20MF の用途: 6 件s: Compact Sensor Interface, LED Lighting Controller, Small Motor or Valve Controller, Battery-Powered Accessory, Industrial Automation Module, Consumer Configuration Module.
Compact Sensor Interface
The ATTINY25-20MF fits a compact sensor interface because its six general-purpose I/O lines can support digital sensors, switches, and status indicators while the 8-bit timer/counter handles periodic sampling or event timing. Its 2 KB of ISP Flash accommodates a focused firmware image, and 128 bytes of EEPROM can retain calibration or configuration values between power cycles. Place the MCU beside the sensor circuitry, route the I/O traces away from switching nodes, and use the exposed pad as a ground connection to improve thermal and return-current performance.
おすすめ
LED Lighting Controller
The ATTINY25-20MF is suitable for LED status, indication, and sequencing nodes where six I/O lines and one 8-bit timer with compare modes provide enough control capability without a larger MCU. Firmware can implement fade patterns, blink rates, and input-driven lighting effects while the 2 KB Flash holds the control routine. Decouple the supply close to the device, keep LED current paths separate from sensitive logic traces, and confirm that each LED current and thermal condition stays within the chosen driver's ratings.
おすすめ
Small Motor or Valve Controller
The ATTINY25-20MF can implement basic motor, solenoid, or valve sequencing where a dedicated high-performance controller is unnecessary. Its six I/O lines can drive control inputs and monitor feedback, while the 8-bit timer/counter supports repeatable switching intervals. Use an external transistor or driver for inductive loads rather than driving the load directly from the MCU. Add flyback protection and keep high-current switching loops compact to limit EMI coupling into the QFN device and adjacent sensing circuitry.
おすすめ
Battery-Powered Accessory
The ATTINY25-20MF is useful in a battery-powered accessory when the design requires autonomous control, retained settings, and modest processing rather than continuous high-throughput computation. The picoPower AVR architecture supports low-power-oriented embedded designs, while 128 bytes of EEPROM avoids consuming Flash for frequently changed configuration. Keep the device in its intended sleep mode between events, disable unused peripherals, and provide a stable clock and supply arrangement so low-power behavior remains predictable across battery voltage and temperature conditions.
おすすめ
Industrial Automation Module
The ATTINY25-20MF can serve as a local automation controller for simple status aggregation, discrete input handling, and actuator sequencing. Its 8-bit AVR architecture, six I/O lines, and dedicated timer provide the basic control resources needed for a compact module, while ISP Flash supports field firmware updates. Follow the manufacturer ICSP guidance to preserve programming access, isolate external connector transients from the MCU, and use a defined ground strategy around the 4 x 4 mm QFN exposed pad.
おすすめ
Consumer Configuration Module
The ATTINY25-20MF fits a consumer configuration module that stores product settings, manages button or indicator behavior, and executes a small state machine. Its 2 KB Flash supports compact application firmware, 128 bytes of EEPROM stores selected settings, and six I/O lines provide enough interface flexibility for buttons, LEDs, and a simple bus or peripheral connection. Minimize standby consumption, define safe states for every output during reset or brownout, and test programming and recovery behavior before volume assembly.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATTINY25-20MF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATTINY25-20MFR |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 20-QFN-EP (4 x 4 mm) | 20-QFN-EP (4 x 4 mm) |
| Core Processor | 8-bit AVR RISC | 8-bit AVR RISC |
| Maximum Clock Frequency | 20 MHz | 20 MHz |
| Flash Memory | 2 KB ISP Flash | 2 KB ISP Flash |
| EEPROM | 128 bytes | 128 bytes |
| SRAM | 128 bytes | 128 bytes |
| General-Purpose I/O Lines | 6 lines | 6 lines |
| Timer/Counter | One 8-bit timer/counter with compare modes | One 8-bit timer/counter with compare modes |
| Ordering Format | MF suffix | MFR suffix with alternate packing format |
| Programming Interface | In-System Programming and ICSP | In-System Programming and ICSP |
主な差別化要因
- Direct ordering-code interchange with the MFR suffix (vs ATTINY25-20MFR)
- 20 MHz operating speed for compact real-time control (vs ATTINY25-20MFR)
- Small exposed-pad package preserves board area (vs ATTINY25-20MFR)
設計ノート
Follow the manufacturer land pattern for the 20-QFN-EP 4 x 4 mm package and connect the exposed thermal pad to ground using the recommended via and copper arrangement. Place input, output, and decoupling connections directly to package pins to minimize loop area. Confirm pin-one orientation against the package drawing because the exposed pad and perimeter pads must not be interchanged during footprint creation.
Preserve access to the ISP programming interface because the manufacturer describes programming through an 8-pin SIL connection using two I/O lines and the reset line. Place the connector and its series resistors where an assembled programmer can reach them. Review the pin multiplexing for the selected programming signals and verify that normal firmware use of the same I/O pins does not interfere with ISP operation.
Do not rely on the ATTINY25-20MFR as an alternative merely because its ordering code is similar; confirm that it shares the 20-QFN-EP footprint, exposed-pad construction, and required packing method. Likewise, do not assume that another manufacturer's 8-bit MCU is drop-in compatible. Review pin assignment, programming interface, reset behavior, timer resources, supply limits, and package geometry before changing the MCU on an existing PCB.
Place the supply bypass capacitor as close as practical to the MCU supply and ground pins, with a short and low-inductance return path to the exposed pad and ground plane. Define input states during reset and brownout so external circuitry cannot back-power or drive the I/O pins unexpectedly. Verify the clock source, operating frequency, and fuse configuration against the manufacturer specification for the intended voltage and temperature range.
コンプライアンス情報
Compliance attributes are not stated in the product information for this ordering code. Confirm the applicable declarations with the manufacturer using the exact MPN.