Microchip Technology

ATTINY25-20MF - 20MHz 8-Bit AVR Microcontroller | Microchip

MPN: ATTINY25-20MF ✓ Nakahanda
20-QFN-EP, 4 x 4 mm Package 20 MHz Speed 2 KB in-system programmable Flash Memory
MOQ: 1 |

ATTINY25-20MF Ulas

The Microchip Technology ATTINY25-20MF is an 8-bit AVR RISC-based CMOS microcontroller operating up to 20 MHz, with 2 KB of in-system programmable Flash memory and a 20-QFN-EP package measuring 4 x 4 mm. The device provides 128 bytes of EEPROM, 128 bytes of SRAM, six general-purpose I/O lines, and 32 general-purpose working registers. Its exposed-pad QFN construction supports compact surface-mount designs requiring more thermal copper than a leaded package.

An 8-bit microcontroller is a programmable integrated circuit that executes instructions using an 8-bit data path. Microcontrollers combine a processor core, nonvolatile program memory, working memory, and peripherals into one device. Within the broader semiconductor hierarchy, the ATTINY25 belongs to the AVR family of reduced-instruction-set computers and to the TinyAVR segment of small, low-power embedded controllers. This makes it suitable for local control logic where a larger processor would add unnecessary cost, power, and board area.

The ATTINY25-20MF combines 2 KB of ISP Flash with 128 bytes of EEPROM and 128 bytes of SRAM. Its 20 MHz AVR core provides substantially more operating headroom than the 10 MHz figure appearing in one retailer listing, while the manufacturer identifies the family as a picoPower AVR RISC-based CMOS device. Six general-purpose I/O lines support digital sensing, switching, and signaling, while the integrated 8-bit timer/counter with compare modes is useful for periodic events, timing, and basic waveform generation.

Program development follows the AVR embedded workflow through Microchip's programming and debug ecosystem. In-System Programming and ICSP permit firmware to be loaded and updated without removing the device from its circuit, while the manufacturer documents programming through an 8-pin SIL connector using two I/O signals and the reset line. The 32 working registers support efficient instruction execution, and the dedicated Flash, SRAM, and EEPROM regions allow firmware code, temporary state, and retained configuration data to occupy separate memories.

Typical applications include compact sensor interfaces, LED status and control nodes, simple motor or valve controllers, industrial automation modules, battery-powered accessories, and small consumer products. The six I/O lines and 8-bit timer are especially useful in designs where a small state machine reads inputs and drives outputs without requiring a high-performance application processor. Its small QFN footprint also supports dense modules and compact control boards.

PCB implementation requires careful attention to the exposed thermal pad, power and ground connectivity, and programming access. Place the device's decoupling capacitor close to its supply pins, connect the exposed pad to the ground plane according to the manufacturer land pattern, and preserve access to the ICSP interface. Confirm the exact pin mapping and exposed-pad geometry against the manufacturer datasheet before releasing artwork.

This product page combines the manufacturer architecture description with exact ordering, package, memory, and interface details, then adds practical programming, layout, replacement, and comparison guidance for engineers evaluating the ATTINY25-20MF in embedded control designs.

Mga alternatibo na pwedeng ilagay na ATTINY25-20MF — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

ATTINY25-20MFR

✅ Drop-In
📦 20-QFN-EP (4 x 4 mm)
Same 20-QFN-EP footprint, 8-bit AVR core, 20 MHz clock, 2 KB Flash, 128-byte EEPROM, 128-byte SRAM, and six I/O lines; ordering suffix changes the packing format

📋 Alternatibo na Reference (hindi sa katalogo)

ATTINY25-20MF Mga Pinakamataas na Rating at Electrical Characteristics

Core Processor 8-bit AVR RISC
Maksimum na Taktiko ng Oras 20 MHz
Flash Memory 2 KB in-system programmable Flash
Flash Organization 1K x 16 bits
EEPROM 128 bytes
SRAM 128 bytes
General-Purpose I/O Lines 6 lines
General-Purpose Working Registers 32 registers
Timer/Counter 1 8-bit timer/counter with compare modes
Packhaging 20-QFN-EP, 4 x 4 mm
Package Pin Count 20 pins
Uri ng Pagpapasok Surface mount, no lead
Programming In-System Programming and ICSP
Architecture picoPower AVR CMOS 8-bit
Series ATtiny, Functional Safety (FuSa) tinyAVR
Katayuan ng Lifecycle Active

Gabay sa Pin Configuration ng ATTINY25-20MF 20 pins

Pin configuration para sa ATTINY25-20MF (20 pins package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.

Pinout diagram ng 20 pins package para sa ATTINY25-20MF

Wala ng detalyadong pinout data na magagamit para sa ATTINY25-20MF.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

ATTINY25-20MF ay nararapat para sa 6 aplikasyons: Compact Sensor Interface, LED Lighting Controller, Small Motor or Valve Controller, Battery-Powered Accessory, Industrial Automation Module, Consumer Configuration Module.

🧩

Compact Sensor Interface

The ATTINY25-20MF fits a compact sensor interface because its six general-purpose I/O lines can support digital sensors, switches, and status indicators while the 8-bit timer/counter handles periodic sampling or event timing. Its 2 KB of ISP Flash accommodates a focused firmware image, and 128 bytes of EEPROM can retain calibration or configuration values between power cycles. Place the MCU beside the sensor circuitry, route the I/O traces away from switching nodes, and use the exposed pad as a ground connection to improve thermal and return-current performance.

💡

LED Lighting Controller

The ATTINY25-20MF is suitable for LED status, indication, and sequencing nodes where six I/O lines and one 8-bit timer with compare modes provide enough control capability without a larger MCU. Firmware can implement fade patterns, blink rates, and input-driven lighting effects while the 2 KB Flash holds the control routine. Decouple the supply close to the device, keep LED current paths separate from sensitive logic traces, and confirm that each LED current and thermal condition stays within the chosen driver's ratings.

🏭

Small Motor or Valve Controller

The ATTINY25-20MF can implement basic motor, solenoid, or valve sequencing where a dedicated high-performance controller is unnecessary. Its six I/O lines can drive control inputs and monitor feedback, while the 8-bit timer/counter supports repeatable switching intervals. Use an external transistor or driver for inductive loads rather than driving the load directly from the MCU. Add flyback protection and keep high-current switching loops compact to limit EMI coupling into the QFN device and adjacent sensing circuitry.

📱

Battery-Powered Accessory

The ATTINY25-20MF is useful in a battery-powered accessory when the design requires autonomous control, retained settings, and modest processing rather than continuous high-throughput computation. The picoPower AVR architecture supports low-power-oriented embedded designs, while 128 bytes of EEPROM avoids consuming Flash for frequently changed configuration. Keep the device in its intended sleep mode between events, disable unused peripherals, and provide a stable clock and supply arrangement so low-power behavior remains predictable across battery voltage and temperature conditions.

🏭

Industrial Automation Module

The ATTINY25-20MF can serve as a local automation controller for simple status aggregation, discrete input handling, and actuator sequencing. Its 8-bit AVR architecture, six I/O lines, and dedicated timer provide the basic control resources needed for a compact module, while ISP Flash supports field firmware updates. Follow the manufacturer ICSP guidance to preserve programming access, isolate external connector transients from the MCU, and use a defined ground strategy around the 4 x 4 mm QFN exposed pad.

🔧

Consumer Configuration Module

The ATTINY25-20MF fits a consumer configuration module that stores product settings, manages button or indicator behavior, and executes a small state machine. Its 2 KB Flash supports compact application firmware, 128 bytes of EEPROM stores selected settings, and six I/O lines provide enough interface flexibility for buttons, LEDs, and a simple bus or peripheral connection. Minimize standby consumption, define safe states for every output during reset or brownout, and test programming and recovery behavior before volume assembly.

Buod ng mga Inirekomendang Produkto

ATTINY25-20MF Microchip Technology Ginagamit sa: Compact Sensor Interface, LED Lighting Controller, Small Motor or Valve Controller, Battery-Powered Accessory, Industrial Automation Module, Consumer Configuration Module ATTINY25-20MFR Same-controller option for reel-fed assembly Ginagamit sa: Compact Sensor Interface, Small Motor or Valve Controller, Industrial Automation Module, Consumer Configuration Module ATTINY25 Base ATtiny25 family device Ginagamit sa: LED Lighting Controller, Battery-Powered Accessory
What are the key specifications of ATTINY25-20MF that engineers should know?
The ATTINY25-20MF is an 8-bit AVR microcontroller rated up to 20 MHz, with 2 KB of ISP Flash, 128 bytes of EEPROM, 128 bytes of SRAM, six general-purpose I/O lines, and 32 working registers. According to the Microchip ATtiny25 product page, it also includes one 8-bit timer/counter with compare modes. The device is supplied in a 20-QFN-EP package measuring 4 x 4 mm. These resources make it suitable for compact embedded-control, timing, and low-pin-count digital I/O designs.
Where can I download the ATTINY25-20MF datasheet PDF?
The official ATTINY25-20MF documentation is available from the Microchip ATtiny25 product page, which provides the manufacturer datasheet, product information, and supporting resources. The device uses the 20-QFN-EP 4 x 4 mm package, so engineers should use the package drawing and pin-description tables for layout and PCB design. A mirror copy of the historical Atmel document also exists, but Microchip remains the authoritative source for current lifecycle and product information.
Where can I find the ATTINY25 pinout?
The ATTINY25 pinout is documented in the manufacturer datasheet under the package and pin-description information for the 20-QFN-EP configuration. Because ATTINY25-20MF uses the 20-pin 4 x 4 mm QFN package with an exposed pad, do not rely on a generic 20-pin diagram without checking the exposed-pad connection and numbering. Keep the ICSP pins accessible in the PCB layout so firmware can be programmed and debugged after assembly.
How much memory does the ATTINY25-20MF have?
The ATTINY25-20MF provides 2 KB of in-system programmable Flash, 128 bytes of EEPROM, and 128 bytes of SRAM. According to the Microchip ATtiny25 product description, the 2 KB Flash stores firmware, the EEPROM retains configuration or calibration data between power cycles, and the SRAM holds working variables and stack state. The limited SRAM makes code-size and stack-depth review important for interrupt-heavy or deeply nested firmware.
What is the maximum operating frequency of ATTINY25-20MF?
The ATTINY25-20MF supports operation up to 20 MHz. The exact ordering information from DigiKey identifies the part as an 8-bit AVR device rated at 20 MHz. According to Microchip, the ATtiny25 family uses a picoPower AVR RISC-based CMOS architecture. Actual clocking should follow the oscillator, fuse, clock-source, and operating-condition recommendations in the manufacturer datasheet rather than assuming every board configuration supports the maximum rate.
How do I program an ATTINY25-20MF?
Program the ATTINY25-20MF through its In-System Programming interface using a compatible AVR programmer. According to the Microchip ATtiny25 product page, the target can be connected through an 8-pin SIL connector that uses two I/O pins and the reset line for In-Circuit Serial Programming. Keep programming access on the PCB and verify connector polarity, target voltage, clock settings, and fuse configuration before programming production boards.
What can replace the ATTINY25-20MF?
The verified pin-compatible replacement is the Microchip ATTINY25-20MFR, which retains the ATTINY25-20MF's 20-QFN-EP footprint, 8-bit AVR architecture, 20 MHz rating, 2 KB Flash, 128-byte EEPROM, 128-byte SRAM, and six I/O lines. Its ordering code differs in packing arrangement. No cross-manufacturer drop-in replacement with documented pin compatibility was identified, so use the manufacturer cross-reference search before approving a different MCU family.
Can ATTINY25-20MFR replace ATTINY25-20MF?
Yes, the ATTINY25-20MFR can serve as a drop-in electrical and PCB replacement for the ATTINY25-20MF because both use the 20-QFN-EP package and the same core, memory, and I/O configuration. The primary distinction is the ordering and packing format associated with the suffix. Confirm the required incoming method, exposed-pad layout, and availability for the intended assembly process before substitution.
ATTINY25-20MF vs ATTINY25-20MFR - which is better for a new PCB?
Choose ATTINY25-20MFR when automated reel-fed assembly is required, and choose ATTINY25-20MF when the assembly process expects the tray-packed ordering code. The two parts share the same 20-QFN-EP 4 x 4 mm footprint and core configuration, including the 8-bit AVR processor, 20 MHz operation, 2 KB Flash, 128-byte EEPROM, and 128-byte SRAM. The choice is therefore primarily mechanical and production-handling related rather than an electrical performance decision.
When should I choose ATTINY25-20MF instead of ATTINY25-20MFR?
Choose ATTINY25-20MF when its tray-style packing arrangement matches the component-handling process used for the build. Choose ATTINY25-20MFR for reel-based automated assembly. Because both ordering codes use the same 20-QFN-EP package and are based on the same ATtiny25 configuration, neither provides a measurable CPU, memory, or I/O advantage. Validate the assembly method, moisture controls, orientation marking, and exposed-pad soldering process before selecting the suffix.
Is ATTINY25-20MF suitable for compact embedded-control boards?
The ATTINY25-20MF is suitable for compact embedded-control boards that need digital control, timing, and nonvolatile configuration storage rather than high computation. Its six I/O lines, 8-bit timer/counter, 2 KB Flash, and 128-byte EEPROM cover basic sensor, actuator, and sequencing tasks. The 4 x 4 mm QFN-EP package also saves board area, although its exposed pad and programming-test requirements demand careful layout and assembly planning.
Where to buy ATTINY25-20MF online?
Use the Request a Quote form on this page to request ATTINY25-20MF availability, current commercial terms, and delivery requirements for the exact ordering code. Because ordering suffix and packing method affect procurement, quote the full MPN ATTINY25-20MF and state the required quantity and assembly format. The manufacturer lists the part as active, but current lot availability and lead time should be confirmed through the quote workflow.
What is the price of ATTINY25-20MF?
Use the Request a Quote form on this page for the current ATTINY25-20MF commercial offer. The page's structured pricing is updated independently from static technical copy, so no fixed unit price is embedded in this FAQ. For a meaningful quotation, include the required quantity, target delivery date, acceptable packing method, and whether the parts are needed for prototype assembly or production.
What is the lead time for ATTINY25-20MF?
Submit an ATTINY25-20MF request through the Request a Quote form on this page and state the required quantity and delivery schedule. Microchip identifies the device as active, but production lead time can vary with factory inventory, package allocation, and customer volume. Requesting a firm date in the quote also allows the manufacturer or authorized channel to confirm the appropriate ATTINY25 ordering suffix for the intended packing process.
Is ATTINY25-20MF in stock?
The current ATTINY25-20MF stock position should be confirmed through the Request a Quote form on this page rather than inferred from a catalog page. The manufacturer lists the device as active, and multiple distribution records exist for the exact ordering code, but those records do not constitute a guaranteed stock commitment. Include the required quantity, target date, and packing preference in the request to obtain a current availability response.
What is the best cross-brand equivalent for ATTINY25-20MF?
No cross-brand drop-in equivalent with documented pin compatibility was identified for the ATTINY25-20MF. The verified alternatives are Microchip ATtiny25 ordering variants that preserve the 20-QFN-EP footprint and electrical architecture. A different manufacturer's 8-bit MCU cannot be treated as interchangeable solely because it has similar Flash memory or clock speed; its pin assignment, reset behavior, programming interface, timer peripherals, and operating limits must match the existing PCB.

Impormasyon ng Talumpati sa Engineering for ATTINY25-20MF — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose ATTINY25-20MF when the assembly flow is designed around its ordering and packing format, and the design needs a compact 8-bit controller with six I/O lines, 2 KB of ISP Flash, 128 bytes of EEPROM, and 128 bytes of SRAM. Choose ATTINY25-20MFR when the same electrical and PCB design must be supplied in the alternate reel-oriented ordering format. Both use the 20-QFN-EP 4 x 4 mm package and support operation up to 20 MHz, so their selection is principally a production-handling decision. If the application requires more GPIO, larger memory, higher clock speed, or a different programming ecosystem, select a different MCU family rather than treating a merely similar 8-bit controller as a drop-in replacement.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto ATTINY25-20MFR
Brand Microchip Technology Microchip Technology
Package 20-QFN-EP (4 x 4 mm) 20-QFN-EP (4 x 4 mm)
Core Processor 8-bit AVR RISC 8-bit AVR RISC
Maximum Clock Frequency 20 MHz 20 MHz
Flash Memory 2 KB ISP Flash 2 KB ISP Flash
EEPROM 128 bytes 128 bytes
SRAM 128 bytes 128 bytes
General-Purpose I/O Lines 6 lines 6 lines
Timer/Counter One 8-bit timer/counter with compare modes One 8-bit timer/counter with compare modes
Ordering Format MF suffix MFR suffix with alternate packing format
Programming Interface In-System Programming and ICSP In-System Programming and ICSP

Pangunahing mga Pagkakaiba

  • Direct ordering-code interchange with the MFR suffix (kumpara saATTINY25-20MFR)
  • 20 MHz operating speed for compact real-time control (kumpara saATTINY25-20MFR)
  • Small exposed-pad package preserves board area (kumpara saATTINY25-20MFR)

Talaan ng Disenyo

Follow the manufacturer land pattern for the 20-QFN-EP 4 x 4 mm package and connect the exposed thermal pad to ground using the recommended via and copper arrangement. Place input, output, and decoupling connections directly to package pins to minimize loop area. Confirm pin-one orientation against the package drawing because the exposed pad and perimeter pads must not be interchanged during footprint creation.

Preserve access to the ISP programming interface because the manufacturer describes programming through an 8-pin SIL connection using two I/O lines and the reset line. Place the connector and its series resistors where an assembled programmer can reach them. Review the pin multiplexing for the selected programming signals and verify that normal firmware use of the same I/O pins does not interfere with ISP operation.

Do not rely on the ATTINY25-20MFR as an alternative merely because its ordering code is similar; confirm that it shares the 20-QFN-EP footprint, exposed-pad construction, and required packing method. Likewise, do not assume that another manufacturer's 8-bit MCU is drop-in compatible. Review pin assignment, programming interface, reset behavior, timer resources, supply limits, and package geometry before changing the MCU on an existing PCB.

Place the supply bypass capacitor as close as practical to the MCU supply and ground pins, with a short and low-inductance return path to the exposed pad and ground plane. Define input states during reset and brownout so external circuitry cannot back-power or drive the I/O pins unexpectedly. Verify the clock source, operating frequency, and fuse configuration against the manufacturer specification for the intended voltage and temperature range.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

Compliance attributes are not stated in the product information for this ordering code. Confirm the applicable declarations with the manufacturer using the exact MPN.

Data napatotohanan sa: 2026-11-14 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

attiny25 pinout attiny25 datasheet attiny25 price attiny25 vs attiny85 attiny25 20ssu attiny25 programming attiny25 20sur attiny25 20su datasheet ATTINY25-20MF datasheet pdf ATTINY25-20MF pinout ATTINY25-20MF replacement ATTINY25-20MF equivalent ATTINY25-20MF footprint ATTINY25-20MF price Microchip ATTINY25-20MF

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology ATTINY25-20MF ATTINY25-20MFR ATtiny25 ATTINY1606-MF AVR tinyAVR picoPower 8-bit microcontroller RISC microcontroller embedded microcontroller semiconductor In-System Programming ICSP 20-QFN-EP QFN family surface mount SMD ISP Flash EEPROM SRAM 8-bit timer/counter general-purpose I/O exposed pad functional safety
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ