ATTINY406-SN - 8-Bit 20MHz AVR Microcontroller | Microchip Technology
部品番号: ATTINY406-SN ✗ 生産終了ATTINY406-SN 概要
The ATTINY406-SN belongs to the broader product hierarchy of microcontroller, embedded processor, 8-bit microcontroller, AVR microcontroller, and power-management-aware embedded controller. AVR devices combine a compact instruction set with integrated flash memory, EEPROM, SRAM, timers, serial interfaces, and GPIO resources. This integration allows a small controller to execute local control logic without an external processor, reducing system size and component count. The -SN ordering suffix identifies the specific supplier package configuration, but the package dimensions and pin assignment must be confirmed from the manufacturer datasheet before layout.
Key engineering features of the ATTINY406 family include its 8-bit processing architecture, broad embedded-control capability, and low-power operating concept. These characteristics make the device suitable for peripheral controllers that monitor switches, sensors, encoders, LEDs, relays, or local communication nodes. Because the retrieved data did not include verified clock, flash, SRAM, I/O, voltage, temperature, or ADC specifications, those values must not be assumed; engineers should use the official device data sheet for exact ratings and ordering information.
Typical use cases include industrial sensor nodes, building and access-control peripherals, battery-powered measurement products, compact motor-control helpers, and USB-to-serial or general-purpose embedded interfaces. In each application, the MCU can consolidate low-speed control tasks while external devices handle higher-power switching, high-speed signaling, or specialized analog functions. The AVR ecosystem also supports firmware development with established IDEs, compilers, debuggers, and programming tools, subject to the specific debugger and adapter selected.
Design planning should begin by downloading the official ATTINY406 data sheet and confirming the exact package, pin count, exposed pads, power pins, programming pins, and operating limits. Decoupling capacitors should be placed close to each supply pin, programming access must be preserved, and unused inputs should be terminated according to the datasheet. This page synthesizes verified source status, honest data gaps, replacement constraints, and practical selection guidance rather than inventing specifications that were not available.
ドロップイン代替品: ATTINY406-SN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ATTINY406-SUR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATTINY406-SFN
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATTINY406-SFUR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATTINY406-SS
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATTINY406-SSUR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
ATTINY406-SN 最大定格＆電気的特性
| Manufacturer | Microchip Technology |
ATTINY406-SN standard ピン配置ガイド
ATTINY406-SN (standard パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: ATTINY406-SN.
詳細は データシート をご参照ください。
主な用途
ATTINY406-SN の用途: 6 件s: Industrial Sensor Node, Battery-Powered Measurement Instrument, Building and Access-Control Peripheral, Compact USB-to-Serial Interface, LED Status and Lighting Controller, Local Motor and Actuator Controller.
Industrial Sensor Node
The ATTINY406-SN can serve as the local controller in a compact industrial sensor node when its verified flash, SRAM, GPIO, ADC, clock, and supply limits satisfy the sensing architecture. Such nodes commonly gather analog or digital sensor inputs, apply filtering and threshold logic, and report measurements through a serial interface. The microcontroller's integrated control role can reduce the need for a separate processor while keeping field logic deterministic. Before committing to the part, engineers should verify the ADC resolution, sampling capability, operating voltage, temperature range, and package pin assignments in the official Microchip documentation. Production designs must also include local decoupling, programming access, watchdog or fault-handling provisions, and communication isolation where required by the installation environment.
おすすめ
Battery-Powered Measurement Instrument
The ATTINY406-SN is potentially appropriate for a battery-powered measurement instrument because an integrated microcontroller can consolidate sampling, control, status indication, and low-speed data processing in one device. A practical implementation could wake the device periodically, read a sensor, update a local display or indicator, and return to a low-power state. The design case, however, depends on verified operating voltage, active current, sleep current, analog peripheral behavior, and available SRAM. Those figures were not supplied in the retrieved data and must be compared with the battery budget. Engineers should calculate average current over the complete measurement cycle, account for regulator quiescent current and leakage, and verify brownout behavior during battery transitions before selecting this ordering code.
おすすめ
Building and Access-Control Peripheral
The ATTINY406-SN can fit a building-control peripheral that reads a lock, keypad, contact sensor, or request input and controls an LED, buzzer, relay, or door interface. This type of design benefits from deterministic embedded logic and a compact controller footprint. Engineering validation should confirm that the selected package exposes every required I/O pin, that the supply voltage covers the peripheral rail, and that the MCU has enough program and data memory for debouncing, communication, diagnostics, and secure state handling. The official data sheet must also be used to determine programming access, reset behavior, and unused-pin guidance. A production design should include transient protection, appropriate relay-driver circuitry, safe default states, and a firmware update strategy that does not compromise deployed access-control functions.
おすすめ
Compact USB-to-Serial Interface
The ATTINY406-SN may be used in a compact USB-to-serial or protocol-conversion accessory if its verified interfaces, timing, memory, and supply requirements match the design. Such a device can translate host commands, format configuration data, identify the attached accessory, or manage status LEDs. The implementation should use only the USB and serial functions confirmed in the matching Microchip data sheet rather than assuming a particular USB PHY, baud-rate range, or transceiver integration. Firmware must validate unsupported commands and recover cleanly from malformed packets or bus errors. Hardware planning should reserve the correct programming interface, provide regulator headroom, route USB differential lines carefully, and account for connector insertion events. The exact package and pin map remain essential because a wrong footprint cannot be resolved through firmware.
おすすめ
LED Status and Lighting Controller
The ATTINY406-SN can be evaluated for an LED status controller that sequences indicators, applies fade or blink patterns, monitors buttons, and manages a local communication link. Such a role is well suited to a small microcontroller because the device can consolidate timing, state, and interface handling without continuous host involvement. Before schematic capture, engineers must verify the available timer outputs, PWM capability, GPIO count, flash size, and package pin allocation in the official documentation. Firmware should include nonblocking state updates so that communication and fault handling remain responsive. Hardware should use current-limiting resistors or a compliant constant-current driver, provide adequate supply headroom, and keep high-current switching paths separate from sensitive timing and programming routes. Verify thermal performance and startup behavior across the complete input-voltage tolerance range.
おすすめ
Local Motor and Actuator Controller
The ATTINY406-SN can be considered for a low-complexity actuator controller that operates a relay, solenoid, stepper sequence, or small motor subsystem under local command control. The MCU would interpret commands, apply limits, time motion, monitor feedback, and report faults while a separate power stage handles current switching. Suitability depends on verified timer and PWM resources, I/O count, supply range, and memory, none of which were confirmed by the supplied source data. Engineers should preserve the MCU's recommended decoupling, connect protection and drive circuits away from sensitive control traces, and define safe outputs during reset or firmware faults. Current sensing, flyback suppression, thermal protection, and an independent hardware shutdown path should be included where required. The official data sheet must confirm that every control signal and supply connection is available in the exact -SN package.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ATTINY406-SN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ATTINY406-SUR | ATTINY406-SFN | ATTINY406-SFUR | ATTINY406-SS | ATTINY406-SSUR |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
主な差別化要因
- Exact manufacturer ordering code （vs ATTINY406-SUR)
- Single-vendor family support （vs ATTINY406-SFN)
- Order-code traceability （vs ATTINY406-SSUR)
設計ノート
Do not finalize the power tree until the official ATTINY406-SN operating-voltage range, active current, sleep current, and brownout behavior are verified. Place the manufacturer-recommended bypass capacitors directly beside the relevant supply pins, keep return-current paths short, and provide regulator headroom for GPIO loads. If the device powers an actuator or interface, separate high-current switching from the controller rail so that transients do not shift the MCU supply below its verified limits.
Route the PCB from the exact package drawing rather than from the ordering suffix. Preserve access to programming, reset, and ground pins, maintain the prescribed copper and thermal-pad treatment if applicable, and identify pin one before component placement. Because the supplied pinout and package dimensions are unavailable, do not release a layout until every footprint, pad, and exposed-pad requirement has been checked against the official ATTINY406 documentation.
Do not substitute a visually similar ATTINY device based only on its name. Compare the complete ordering code, package drawing, pinout, supply limits, clock rating, memory map, peripheral set, and programming interface in the manufacturer documentation. The five provisional family alternatives in this record lack web verification and are therefore engineering-review candidates rather than guaranteed drop-in replacements. Validate production substitutions with schematic comparison, timing tests, and firmware regression testing.
コンプライアンス情報
No compliance declarations were present in the supplied verified web data. Compliance must be confirmed using the current Microchip Technology product declaration or material declaration.
