Microchip Technology

ATTINY414-SSF - 20MHz AVR MCU, 4KB Flash | Microchip

部品番号: ATTINY414-SSF ✓ 生産中
14-pin SOIC Package 20 MHz Speed 4 KB (4K x 8) Memory
MOQ: 1 |

ATTINY414-SSF 概要

Microchip Technology ATTINY414-SSF is an 8-bit AVR tinyAVR microcontroller rated up to 20 MHz, with 4 KB Flash, 256 bytes SRAM, 128 bytes EEPROM, and 12 general-purpose I/O pins in a 14-pin SOIC package. It combines an AVR processor with core-independent peripherals, Event System, SleepWalking, accurate analog functions, and a 10-bit ADC.

An AVR microcontroller is a compact embedded-control IC that executes programmed instructions from nonvolatile Flash memory while reading sensors and controlling digital or analog peripherals. The tinyAVR 1 family combines an 8-bit AVR core with event-driven hardware and low-power operation. This places the ATTINY414-SSF in the hierarchy of embedded microcontroller, embedded processor, semiconductor, and power-management-aware control device for small industrial, consumer, and automotive-adjacent systems.

Key features include a hardware multiplier, 4 KB of Flash, 256 bytes of SRAM, and 128 bytes of EEPROM. Its connectivity options include I2C, IrDA, LINbus, SPI, and UART/USART. The analog section includes a 10-channel, 10-bit ADC and one 8-bit DAC. The SSF ordering designation supports an industrial operating range from -40°C to 125°C, making the device appropriate for designs requiring extended temperature operation.

The device belongs to the ATtiny212, ATtiny214, ATtiny412, ATtiny414, and ATtiny416 family, whose SRAM organization differs by member. The ATtiny414 specifically provides 256 bytes of SRAM and 128 bytes of EEPROM. Its low-power architecture includes Event System and SleepWalking functions, allowing peripherals to initiate activity or wake the core without requiring continuous software polling. These hardware mechanisms can reduce processing overhead in event-driven control systems.

Typical applications include compact sensor nodes, industrial condition-monitoring terminals, low-power control panels, LIN-connected automotive peripherals, communication bridges, and small actuator controllers. The combination of 12 I/O pins, multiple serial interfaces, on-chip analog conversion, and a 14-pin SOIC footprint supports compact mixed-signal designs where board area and component count are important.

When laying out the circuit, place decoupling capacitors close to the supply and ground pins, route sensitive analog inputs away from fast-switching nodes, and maintain the operating voltage limits defined by the manufacturer datasheet. Confirm the programmed clock configuration because catalog listings may show a 16 MHz product-page frequency while the manufacturer describes the family as capable of running up to 20 MHz.

This page combines manufacturer specifications, package and pinout guidance, functional alternatives, comparison parameters, and practical embedded-design considerations into a procurement-oriented reference for engineers evaluating the ATTINY414-SSF.

ドロップイン代替品: ATTINY414-SSF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

ATTINY414-SSN

✅ ドロップイン
📦 14-pin SOIC
Maximum operating temperature is 105°C versus 125°C for ATTINY414-SSF; core, memory, clock capability, and package remain equivalent

📋 参考代替品(カタログ未掲載)

ATTINY104-SSFR

✅ ドロップイン
📦 14-pin SOIC
Maximum CPU frequency is 12 MHz versus 20 MHz for ATTINY414-SSF, a 40% reduction; temperature range and -40°C lower bound are unchanged

📋 参考代替品(カタログ未掲載)

ATTINY414-SSF 最大定格&電気的特性

Product Type 8-bit AVR tinyAVR 1 functional-safety microcontroller
Maximum CPU Frequency 20 MHz
Catalog Listing Frequency 16 MHz
Flash Memory 4 KB (4K x 8)
SRAM 256 bytes
EEPROM 128 bytes
Core Architecture 8-bit AVR with hardware multiplier
General-Purpose I/O Count 12 pins
ADC 10-channel, 10-bit
DAC 1-channel, 8-bit
Serial Interfaces I2C, IrDA, LINbus, SPI, UART/USART
動作温度 -40°C to 125°C
パッケージ 14-pin SOIC
実装タイプ Surface mount
Packaging Tube
Core Independent Peripherals Present
Event System Present
SleepWalking Present

ATTINY414-SSF 14-pin soic ピン配置ガイド

ATTINY414-SSF (14-pin soic パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。

ATTINY414-SSF の 14-pin soic パッケージピン配置図

詳細なピン配置データはありません: ATTINY414-SSF.

詳細は データシート をご参照ください。

主な用途

ATTINY414-SSF の用途: 6 件s: Industrial Sensor Node, LIN-Connected Automotive Peripheral, Battery-Powered Condition Monitor, Compact Communication Bridge, Low-Power Actuator Controller, Small Analog Control Panel.

🏭

Industrial Sensor Node

The ATTINY414-SSF fits compact industrial sensor nodes because it combines a 20 MHz-capable 8-bit AVR core, 12 I/O pins, a 10-channel 10-bit ADC, and extended -40°C-to-125°C operation in a 14-pin SOIC package. It can acquire analog sensor levels, apply filtering or threshold logic, and publish results through I2C, SPI, or UART/USART. The Event System permits peripherals to trigger activity without continuous polling, while SleepWalking supports low-power monitoring. Designers should preserve analog signal separation, provide local supply decoupling, and confirm the programmed clock before committing the board to production.

🚗

LIN-Connected Automotive Peripheral

The ATTINY414-SSF supports LINbus alongside I2C, SPI, UART/USART, and IrDA, making it appropriate for a compact LIN peripheral that coordinates switches, sensors, or actuator commands. Its 20 MHz maximum operating speed supports event-driven control, and its core-independent peripherals complement the Event System and SleepWalking functions. The MCU should be paired with an appropriate LIN transceiver rather than connected directly to the bus. Firmware must configure the correct clock, communication timing, watchdog behavior, and pin multiplexing, while the PCB must preserve signal integrity between the transceiver and controller.

🔋

Battery-Powered Condition Monitor

The ATTINY414-SSF is suitable for battery-powered condition monitoring where an 8-bit controller must combine low-power operation with several sensing and communications functions. SleepWalking allows supported peripheral activity to wake or coordinate with the AVR core, reducing the need for continuous polling, and the 256-byte SRAM plus 128-byte EEPROM provide local state and parameter storage. Its 10-bit ADC can monitor up to 10 analog inputs. Designers should calculate average and peak current in the intended sleep mode, disable unused peripherals, and validate the regulator’s quiescent current because total standby demand depends on the complete power-supply design.

🌐

Compact Communication Bridge

The ATTINY414-SSF can serve as a compact bridge between an embedded sensor, actuator, and host interface because it provides I2C, SPI, UART/USART, IrDA, and LINbus connectivity in one 14-pin device. The hardware multiplier and 20 MHz-capable AVR core support efficient protocol conversion and framing, while 4 KB Flash accommodates moderately sized firmware. Pin multiplexing must be reviewed carefully because alternate peripheral functions can limit simultaneous interface availability. The design should include pull-up or termination components where required, route serial signals away from analog inputs, and validate timing at the intended clock and bus rates.

🔧

Low-Power Actuator Controller

The ATTINY414-SSF can control small relays, valves, indicators, or other actuators in a compact embedded module because its 12 I/O pins and multiple timer-capable peripherals reduce the need for external logic. The 20 MHz maximum clock supports responsive debouncing, timing, and state-machine execution, while the Event System allows peripheral events to drive activity efficiently. Output drive capability, inductive-load protection, and supply-current limits must be checked against the actuator rather than assumed from the I/O count. The schematic should include appropriate flyback or suppression networks and separate sensitive analog paths from switching nodes.

🎛️

Small Analog Control Panel

The ATTINY414-SSF fits a small analog control panel that must acquire several sensor inputs and present a local digital interface. Its 10-channel 10-bit ADC supports multiplexed monitoring, the 8-bit DAC can provide a simple control or reference output, and the 14-pin SOIC footprint keeps the controller compact. The Event System assists with deterministic peripheral sequencing, and the hardware multiplier benefits arithmetic in calibration or compensation routines. The board should use a quiet reference for the ADC and DAC, route analog inputs away from digital clocks and power converters, and include calibration data in EEPROM when measurement accuracy depends on production trimming.

おすすめ製品の概要

What are the key specifications of ATTINY414-SSF that engineers should know?
The ATTINY414-SSF is an 8-bit AVR microcontroller with up to 20 MHz operation, 4 KB Flash, 256 bytes SRAM, 128 bytes EEPROM, 12 I/O pins, and a -40°C-to-125°C temperature range in a 14-pin SOIC. According to the Microchip ATtiny414 product page, the device also includes a hardware multiplier, Event System, SleepWalking, a 10-channel 10-bit ADC, and a one-channel 8-bit DAC. Its supported connectivity includes I2C, SPI, UART/USART, IrDA, and LINbus.
Where can I download the ATTINY414-SSF datasheet PDF?
The ATTINY414-SSF datasheet PDF is available from Microchip Technology through the manufacturer datasheet link on this page. The family document is titled “AVR Microcontroller with Core Independent Peripherals ATtiny214/414/814,” and an additional Microchip PDF covers ATtiny212, ATtiny214, ATtiny412, ATtiny414, and ATtiny416. Use the pin-description and electrical-characteristics tables for the 14-pin SSF package when assigning PCB nets and validating operating limits.
What is the difference between ATTINY414-SSF and ATTINY414-SSN?
The principal documented difference between ATTINY414-SSF and ATTINY414-SSN is the temperature rating: SSF supports -40°C to 125°C, while SSN supports -40°C to 105°C. Microchip’s ATtiny414 family documentation identifies both as 20 MHz-capable devices with a hardware multiplier and low-power peripherals. The SSF version is therefore the appropriate choice when the enclosure can exceed 105°C, while SSN can serve applications confined to its lower maximum temperature.
Is ATTINY414-SSF the same as ATTINY414-SSFR?
The ATTINY414-SSF and ATTINY414-SSFR share the same Microchip ATtiny414 device and 14-pin SOIC footprint, but their order codes indicate different delivery packaging: SSF is supplied in a tube, while SSFR is supplied in tape and reel. The ATTINY414-SSFR listing identifies the same 8-bit AVR architecture, 16 MHz catalog frequency, 4 KB Flash, and 14-SOIC package. PCB compatibility therefore does not remove the need to match the requested assembly and ordering format.
What is the ATTINY414-SSF pinout?
The ATTINY414-SSF uses a 14-pin SOIC package, and its complete numbered pin map must be taken from the manufacturer’s pin-description table. Use the manufacturer datasheet for the definitive correspondence among supply, ground, reset, programming, analog, and general-purpose I/O signals because several ATtiny devices support alternate peripheral functions on the same pins. The 14-pin package drawing is represented by the SOIC-14 package diagram on this page.
What can replace the ATTINY414-SSF on an existing PCB?
The closest documented drop-in replacement is the ATTINY414-SSN because it uses the same Microchip ATtiny414 family, 14-pin SOIC footprint, 4 KB Flash, 256-byte SRAM, and 128-byte EEPROM; its main limitation is the lower 105°C maximum temperature versus 125°C for the SSF. The ATTINY414-SSFR can also fit the same PCB but changes the packaging from tube to tape and reel. Firmware, pin multiplexing, clock settings, and peripheral assignments should be revalidated before substitution.
ATTINY414-SSF vs ATTINY104-SSFR: which is better for a fast control application?
The ATTINY414-SSF is the better choice for a control application requiring greater processing speed because the Microchip ATtiny414 supports up to 20 MHz, while the comparison data for ATTINY104-SSFR lists 12 MHz. Both use an 8-bit AVR core and the same 14-pin SOIC family format, but higher clock capability alone does not prove complete peripheral compatibility. Review the I/O multiplexing, analog block, memory organization, and package drawing before treating ATTINY104-SSFR as a functional replacement.
When should I choose ATTINY414-SSF over ATTINY414-SSN?
Choose ATTINY414-SSF when the operating environment may exceed 105°C and the design requires the device’s -40°C-to-125°C rating. Choose ATTINY414-SSN for installations that remain at or below 105°C. Because both parts use the same ATtiny414 family and 14-pin SOIC package, the temperature requirement is the principal selection criterion, subject to confirmation of current ordering and supply conditions.
Can ATTINY414-SSF be used for LIN bus communication?
Yes, the ATTINY414-SSF supports LINbus connectivity in addition to I2C, IrDA, SPI, and UART/USART. According to the manufacturer product page and device data, its Event System and core-independent peripherals are suited to event-driven communication and low-power control. A production design still requires the correct transceiver, connector protection, reference clock configuration, bus timing setup, and validation of the selected LIN operating mode.
How is the ATTINY414-SSF programmed and debugged?
The ATTINY414-SSF is programmed through its device programming interface using a compatible AVR programmer, while an in-circuit debugger can support development and fault inspection. Microchip’s ATtiny programming documentation and the datasheet’s programming and debug interface sections should be used to confirm the required clock, programming voltage, isolation, and tool settings. The ATTINY414 programming search phrase is especially useful when selecting a tool that supports the exact device family and package.
Does ATTINY414-SSF work with the Arduino IDE?
The ATTINY414-SSF can be used in Arduino-compatible workflows when the installed board package, programmer, core support, and fuse settings are configured for the ATtiny414 device and its 20 MHz maximum clock. A generic Arduino Uno target is not automatically suitable because the ATtiny414 has a different pin arrangement and requires the correct AVR core definition. Confirm the package, clock source, and boot or programming arrangement before uploading firmware.
Where can I buy ATTINY414-SSF online?
Use the Request a Quote form on this page to request ATTINY414-SSF pricing, stock confirmation, and lead time from XAIPART. The manufacturer product page and authorized distribution information identify the part as the Microchip ATtiny414 in a 14-pin SOIC package, with the SSF order code specifying tube packaging and a -40°C-to-125°C temperature range. The Request a Quote form is the appropriate route for current commercial terms.
What is the price of ATTINY414-SSF?
The current ATTINY414-SSF price should be requested through the Request a Quote form on this page because commercial terms can change with quantity, inventory, and order packaging. The product is identified as a 4 KB Flash, 256-byte SRAM, 128-byte EEPROM ATtiny414 microcontroller in a 14-pin SOIC tube package. Submit the required quantity and target delivery details to obtain a current quotation.
What is the lead time for ATTINY414-SSF?
The current ATTINY414-SSF lead time should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, tube packaging, component availability, and manufacturing continuity. The manufacturer lists the ATtiny414 family as active, and the part is offered in a 14-pin SOIC configuration with the SSF temperature grade, but those facts do not replace a live inventory commitment.
Is ATTINY414-SSF in stock?
Current ATTINY414-SSF inventory should be checked through the Request a Quote form on this page because stock is time-sensitive and depends on the exact order code and requested quantity. The ATTINY414-SSF is the tube-packaged, 14-pin SOIC version of Microchip’s ATTINY414, while ATTINY414-SSFR denotes tape-and-reel delivery. Include the required package format and quantity in the request to obtain an accurate availability response.

エンジニアリング参考データ: ATTINY414-SSF — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the ATTINY414-SSF when a compact 14-pin SOIC design needs the ATtiny414 family’s up-to-20-MHz AVR core, 4 KB Flash, 256-byte SRAM, 128-byte EEPROM, 10-bit ADC, 8-bit DAC, and extended -40°C-to-125°C range. Choose ATTINY414-SSN when the same device family and electrical behavior are needed but the installation remains below 105°C; it provides the closest temperature-limited substitution. Consider ATTINY104-SSFR only when its lower 12 MHz maximum clock and broader 125°C range satisfy the application, after checking analog, peripheral, and pin-multiplexing compatibility. For new designs, verify whether 20 MHz operation is required, whether the ADC and DAC justify the ATtiny414 feature set, and whether the SOIC package remains appropriate for the assembly process.

代替品との比較

パラメータ この製品 ATTINY414-SSN ATTINY104-SSFR
Brand Microchip Technology Microchip Technology Microchip Technology
Package 14-pin SOIC 14-pin SOIC 14-pin SOIC
Maximum CPU Frequency 20 MHz 20 MHz 12 MHz
Core Processor 8-bit AVR 8-bit AVR 8-bit AVR
Maximum Operating Temperature 125°C 105°C 125°C
Connectivity I2C, IrDA, LINbus, SPI, UART/USART I2C, IrDA, LINbus, SPI, UART/USART I2C, IrDA, LINbus, SPI, UART/USART
Order Packaging Tube Tube Tape and reel

主な差別化要因

  • Higher clock capability than the ATtiny104 comparison candidate (vs ATTINY104-SSFR)
  • Broader temperature envelope than ATTINY414-SSN (vs ATTINY414-SSN)
  • Documented rich analog and event-driven peripheral set (vs ATTINY104-SSFR)

設計ノート

Place the required supply and ground decoupling capacitors directly beside the corresponding ATTINY414-SSF pins, with the shortest possible return path. Keep analog and digital return-current paths disciplined so switching-node currents do not cross the ADC input region. Validate brownout, startup, and shutdown behavior across the complete supply range. For battery-powered nodes, measure the MCU and supporting circuitry in every sleep mode because the ATtiny414 low-power features do not determine the current drawn by external sensors, pull resistors, regulators, or communication transceivers.

Assign analog inputs according to the manufacturer pin-description table and preserve the resulting alternate-function limitations. The device supports I2C, SPI, UART/USART, IrDA, LINbus, ADC, and DAC functions, so several pins may have several possible roles. Route fast serial and clock signals away from analog inputs, use short ground references for analog sources, and locate external precision components close to the pins they serve. Because a complete verified pin-name list is not reproduced on this page, use the manufacturer pin-description table as the authoritative assignment reference.

Do not treat the 16 MHz figure shown in distributor listings as the family’s absolute performance limit; Microchip describes the ATtiny414 as capable of operating up to 20 MHz. Confirm the selected clock source, fuse configuration, operating conditions, and timeout settings in the programming tool. Likewise, do not confuse ATTINY414-SSF tube packaging with ATTINY414-SSFR tape-and-reel packaging. The former is the exact target order code, while a firmware-compatible order code is not automatically the correct procurement option for the intended assembly process.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The family is identified as tinyAVR 1 functional-safety technology, but no specific AEC-Q100 qualification, RoHS declaration, REACH declaration, lead-free statement, halogen-free statement, or conflict-minerals statement was established for the exact ATTINY414-SSF order code.

関連検索

attiny414 datasheet attiny414 ssfr attiny414 ssnr attiny414 ssn attiny414 arduino attiny414 programming attiny414 programmer attiny414 arduino ide attiny414 pdf ATTINY414-SSF pinout ATTINY414-SSF datasheet pdf ATTINY414-SSF replacement ATTINY414-SSF equivalent ATTINY414-SSF price ATTINY414-SSF vs ATTINY104-SSFR

関連部品&用語

Microchip Technology ATTINY414-SSF ATTINY414 ATTINY414-SSN ATTINY414-SSFR ATTINY104-SSFR AVR tinyAVR 1 8-bit microcontroller embedded microcontroller embedded processor semiconductor hardware multiplier Event System SleepWalking 10-bit ADC 8-bit DAC I2C SPI UART/USART LINbus IrDA 14-pin SOIC SOIC family surface mount
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示