ATTINY414-SSF - 20MHz AVR MCU, 4KB Flash | Microchip
MPN: ATTINY414-SSF ✓ NakahandaATTINY414-SSF Ulas
An AVR microcontroller is a compact embedded-control IC that executes programmed instructions from nonvolatile Flash memory while reading sensors and controlling digital or analog peripherals. The tinyAVR 1 family combines an 8-bit AVR core with event-driven hardware and low-power operation. This places the ATTINY414-SSF in the hierarchy of embedded microcontroller, embedded processor, semiconductor, and power-management-aware control device for small industrial, consumer, and automotive-adjacent systems.
Key features include a hardware multiplier, 4 KB of Flash, 256 bytes of SRAM, and 128 bytes of EEPROM. Its connectivity options include I2C, IrDA, LINbus, SPI, and UART/USART. The analog section includes a 10-channel, 10-bit ADC and one 8-bit DAC. The SSF ordering designation supports an industrial operating range from -40°C to 125°C, making the device appropriate for designs requiring extended temperature operation.
The device belongs to the ATtiny212, ATtiny214, ATtiny412, ATtiny414, and ATtiny416 family, whose SRAM organization differs by member. The ATtiny414 specifically provides 256 bytes of SRAM and 128 bytes of EEPROM. Its low-power architecture includes Event System and SleepWalking functions, allowing peripherals to initiate activity or wake the core without requiring continuous software polling. These hardware mechanisms can reduce processing overhead in event-driven control systems.
Typical applications include compact sensor nodes, industrial condition-monitoring terminals, low-power control panels, LIN-connected automotive peripherals, communication bridges, and small actuator controllers. The combination of 12 I/O pins, multiple serial interfaces, on-chip analog conversion, and a 14-pin SOIC footprint supports compact mixed-signal designs where board area and component count are important.
When laying out the circuit, place decoupling capacitors close to the supply and ground pins, route sensitive analog inputs away from fast-switching nodes, and maintain the operating voltage limits defined by the manufacturer datasheet. Confirm the programmed clock configuration because catalog listings may show a 16 MHz product-page frequency while the manufacturer describes the family as capable of running up to 20 MHz.
This page combines manufacturer specifications, package and pinout guidance, functional alternatives, comparison parameters, and practical embedded-design considerations into a procurement-oriented reference for engineers evaluating the ATTINY414-SSF.
Mga alternatibo na pwedeng ilagay na ATTINY414-SSF — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
ATTINY414-SSN
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ATTINY104-SSFR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ATTINY414-SSF Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 8-bit AVR tinyAVR 1 functional-safety microcontroller |
| Maximum CPU Frequency | 20 MHz |
| Catalog Listing Frequency | 16 MHz |
| Flash Memory | 4 KB (4K x 8) |
| SRAM | 256 bytes |
| EEPROM | 128 bytes |
| Core Architecture | 8-bit AVR with hardware multiplier |
| General-Purpose I/O Count | 12 pins |
| ADC | 10-channel, 10-bit |
| DAC | 1-channel, 8-bit |
| Serial Interfaces | I2C, IrDA, LINbus, SPI, UART/USART |
| Temperature na Operasyon | -40°C to 125°C |
| Packhaging | 14-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Packaging | Tube |
| Core Independent Peripherals | Present |
| Event System | Present |
| SleepWalking | Present |
Gabay sa Pin Configuration ng ATTINY414-SSF 14-pin soic
Pin configuration para sa ATTINY414-SSF (14-pin soic package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa ATTINY414-SSF.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ATTINY414-SSF ay nararapat para sa 6 aplikasyons: Industrial Sensor Node, LIN-Connected Automotive Peripheral, Battery-Powered Condition Monitor, Compact Communication Bridge, Low-Power Actuator Controller, Small Analog Control Panel.
Industrial Sensor Node
The ATTINY414-SSF fits compact industrial sensor nodes because it combines a 20 MHz-capable 8-bit AVR core, 12 I/O pins, a 10-channel 10-bit ADC, and extended -40°C-to-125°C operation in a 14-pin SOIC package. It can acquire analog sensor levels, apply filtering or threshold logic, and publish results through I2C, SPI, or UART/USART. The Event System permits peripherals to trigger activity without continuous polling, while SleepWalking supports low-power monitoring. Designers should preserve analog signal separation, provide local supply decoupling, and confirm the programmed clock before committing the board to production.
Inirekomenda
LIN-Connected Automotive Peripheral
The ATTINY414-SSF supports LINbus alongside I2C, SPI, UART/USART, and IrDA, making it appropriate for a compact LIN peripheral that coordinates switches, sensors, or actuator commands. Its 20 MHz maximum operating speed supports event-driven control, and its core-independent peripherals complement the Event System and SleepWalking functions. The MCU should be paired with an appropriate LIN transceiver rather than connected directly to the bus. Firmware must configure the correct clock, communication timing, watchdog behavior, and pin multiplexing, while the PCB must preserve signal integrity between the transceiver and controller.
Inirekomenda
Battery-Powered Condition Monitor
The ATTINY414-SSF is suitable for battery-powered condition monitoring where an 8-bit controller must combine low-power operation with several sensing and communications functions. SleepWalking allows supported peripheral activity to wake or coordinate with the AVR core, reducing the need for continuous polling, and the 256-byte SRAM plus 128-byte EEPROM provide local state and parameter storage. Its 10-bit ADC can monitor up to 10 analog inputs. Designers should calculate average and peak current in the intended sleep mode, disable unused peripherals, and validate the regulator’s quiescent current because total standby demand depends on the complete power-supply design.
Inirekomenda
Compact Communication Bridge
The ATTINY414-SSF can serve as a compact bridge between an embedded sensor, actuator, and host interface because it provides I2C, SPI, UART/USART, IrDA, and LINbus connectivity in one 14-pin device. The hardware multiplier and 20 MHz-capable AVR core support efficient protocol conversion and framing, while 4 KB Flash accommodates moderately sized firmware. Pin multiplexing must be reviewed carefully because alternate peripheral functions can limit simultaneous interface availability. The design should include pull-up or termination components where required, route serial signals away from analog inputs, and validate timing at the intended clock and bus rates.
Inirekomenda
Low-Power Actuator Controller
The ATTINY414-SSF can control small relays, valves, indicators, or other actuators in a compact embedded module because its 12 I/O pins and multiple timer-capable peripherals reduce the need for external logic. The 20 MHz maximum clock supports responsive debouncing, timing, and state-machine execution, while the Event System allows peripheral events to drive activity efficiently. Output drive capability, inductive-load protection, and supply-current limits must be checked against the actuator rather than assumed from the I/O count. The schematic should include appropriate flyback or suppression networks and separate sensitive analog paths from switching nodes.
Inirekomenda
Small Analog Control Panel
The ATTINY414-SSF fits a small analog control panel that must acquire several sensor inputs and present a local digital interface. Its 10-channel 10-bit ADC supports multiplexed monitoring, the 8-bit DAC can provide a simple control or reference output, and the 14-pin SOIC footprint keeps the controller compact. The Event System assists with deterministic peripheral sequencing, and the hardware multiplier benefits arithmetic in calibration or compensation routines. The board should use a quiet reference for the ADC and DAC, route analog inputs away from digital clocks and power converters, and include calibration data in EEPROM when measurement accuracy depends on production trimming.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ATTINY414-SSF — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ATTINY414-SSN | ATTINY104-SSFR |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 12 MHz |
| Core Processor | 8-bit AVR | 8-bit AVR | 8-bit AVR |
| Maximum Operating Temperature | 125°C | 105°C | 125°C |
| Connectivity | I2C, IrDA, LINbus, SPI, UART/USART | I2C, IrDA, LINbus, SPI, UART/USART | I2C, IrDA, LINbus, SPI, UART/USART |
| Order Packaging | Tube | Tube | Tape and reel |
Pangunahing mga Pagkakaiba
- Higher clock capability than the ATtiny104 comparison candidate (kumpara saATTINY104-SSFR)
- Broader temperature envelope than ATTINY414-SSN (kumpara saATTINY414-SSN)
- Documented rich analog and event-driven peripheral set (kumpara saATTINY104-SSFR)
Talaan ng Disenyo
Place the required supply and ground decoupling capacitors directly beside the corresponding ATTINY414-SSF pins, with the shortest possible return path. Keep analog and digital return-current paths disciplined so switching-node currents do not cross the ADC input region. Validate brownout, startup, and shutdown behavior across the complete supply range. For battery-powered nodes, measure the MCU and supporting circuitry in every sleep mode because the ATtiny414 low-power features do not determine the current drawn by external sensors, pull resistors, regulators, or communication transceivers.
Assign analog inputs according to the manufacturer pin-description table and preserve the resulting alternate-function limitations. The device supports I2C, SPI, UART/USART, IrDA, LINbus, ADC, and DAC functions, so several pins may have several possible roles. Route fast serial and clock signals away from analog inputs, use short ground references for analog sources, and locate external precision components close to the pins they serve. Because a complete verified pin-name list is not reproduced on this page, use the manufacturer pin-description table as the authoritative assignment reference.
Do not treat the 16 MHz figure shown in distributor listings as the family’s absolute performance limit; Microchip describes the ATtiny414 as capable of operating up to 20 MHz. Confirm the selected clock source, fuse configuration, operating conditions, and timeout settings in the programming tool. Likewise, do not confuse ATTINY414-SSF tube packaging with ATTINY414-SSFR tape-and-reel packaging. The former is the exact target order code, while a firmware-compatible order code is not automatically the correct procurement option for the intended assembly process.
Impormasyon ng Pagsunod sa Kautusan
The family is identified as tinyAVR 1 functional-safety technology, but no specific AEC-Q100 qualification, RoHS declaration, REACH declaration, lead-free statement, halogen-free statement, or conflict-minerals statement was established for the exact ATTINY414-SSF order code.