BTS500801TEAAUMA1 - 10A Smart High-Side Switch | Infineon PROFET
部品番号: BTS500801TEAAUMA1 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.37 | $4.37 |
| 10 | $3.93 | $39.30 |
| 100 | $3.49 | $349.00 |
| 500 | $3.1 | $1,550.00 |
| 1,000 | $2.74 | $2,740.00 |
BTS500801TEAAUMA1 概要
A high-side switch (also called a high-side driver) is a semiconductor switch placed between the positive supply rail and the load, in contrast to a low-side switch that sits between the load and ground. Within the power management hierarchy, this part belongs to the smart power switch family -> power distribution switch -> load driver -> power management IC. Smart high-side switches integrate the MOSFET, gate driver, charge pump, and protection logic into a single package, replacing discrete MOSFET + driver designs in body electronics and similar applications.
Key features include a 12 V nominal operating supply (4.5 V to 28 V load supply range), integrated reverse-battery protection, over-current and over-temperature shutdown with auto-restart, ground-loss detection, ESD protection, and a diagnostic current-sense (IS) pin for load current feedback. The device also provides short-circuit protection with configurable current limit and over-voltage clamp (active clamp) at the load. The PG-TO252-5-11 package offers a low thermal resistance path via the drain tab, enabling sustained 10 A operation on FR4 PCB with adequate copper area.
The BTS50080-1TEA architecture combines an N-channel vertical power MOSFET with a charge pump that generates the gate voltage above the supply rail, ensuring full enhancement of the power stage even at low battery voltages. The diagnostic current-sense output delivers a current proportional to the load current, allowing the microcontroller to detect open-load, short-to-ground, and short-to-battery faults without additional shunt resistors.
Typical applications include automotive lighting (headlamps, tail lamps, turn signals, interior LED modules), body electronics (door locks, seat controllers, mirror heaters), 12 V relay and solenoid replacement, and industrial 24 V (with derating) actuator drivers. According to the Infineon BTS50080-1TEA datasheet, the part targets harsh automotive environments with high inrush loads.
When designing with this device, ensure the PCB copper area around the drain tab is sized to keep junction temperature below 150 C at the worst-case ambient. A series resistor or TVS on the input protects against load-dump transients above 28 V, and the IS pin requires an external resistor to convert sense current to a voltage readable by the ADC.
This page synthesizes distributor pricing from DigiKey, Mouser, Octopart, and LCSC, plus drop-in Infineon PROFET alternatives and practical design notes not aggregated in the manufacturer datasheet alone.
ドロップイン代替品: BTS500801TEAAUMA1 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: BTS500801TEAAUMA1 （同一形状・フットプリント） — 相違点: Package, Diagnostic Output, Topology, Mounting Type, Product Type.
クイック比較ツール — 並列比較する代替部品を選択:
BTS50080-1TEA
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS500801TEBAUMA1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS500801TMAATMA1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS500801TMBAKSA1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS500551TMBAKSA1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
VN5E016MH-E
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BTS500801TEAAUMA1 最大定格＆電気的特性
| Product Family | Classic PROFET (smart high-side switch) |
| トポロジー | 1:1 N-Channel high-side |
| Nominal Supply Voltage | 12 V |
| Load Supply Voltage Range | 4.5 V to 28 V |
| Continuous Load Current | 10 A |
| On-State Resistance (RDS(on)) | 10 milliohms (typical) |
| 出力構成 | High-side |
| Number of Channels | 1 |
| Fault Protection | Current limiting, over-temperature, over-voltage, reverse battery, ground loss, ESD |
| Diagnostic Output | Current sense (IS pin) |
| パッケージ | PG-TO252-5-11 (DPAK-5, 4+Tab) |
| 実装タイプ | Surface Mount |
| Packaging | Tape & Reel |
| Automotive Qualified | Yes (AEC-Q100 target application) |
| RoHS ステータス | Compliant |
| Power Transistor Technology | N-channel vertical power MOSFET with charge pump |
BTS500801TEAAUMA1 ピン構成
| ピン 1 | OUT (Load) — Power output to the load (drain of internal N-channel MOSFET) |
| ピン 2 | GND — Logic and sense ground reference |
| ピン 3 | IN (Vs) — 12 V battery supply input (drain tab internally connected) |
| ピン 4 | IS — Current sense diagnostic output (current proportional to load) |
| ピン 5 | Tab/Drain — Exposed pad - load-side drain, solder to PCB copper for thermal dissipation |
主な用途
BTS500801TEAAUMA1 の用途: 6 件s: Automotive Headlamp and Tail Lamp Driver, 12 V Relay and Solenoid Replacement, Interior LED Lighting Module Driver, Automotive Body Control Module (BCM) Load Driver, Industrial 24 V Actuator and Valve Driver, 12 V Heated Seat and Mirror Heater Driver.
Automotive Headlamp and Tail Lamp Driver
The BTS500801TEAAUMA1's 10 A continuous load current and 28 V load-dump tolerance make it ideal for direct drive of automotive headlamp and tail lamp bulbs. Its 10 milliohm typical RDS(on) limits steady-state conduction loss to roughly 1 W at full load, which the PG-TO252-5-11 drain tab can dissipate on standard FR4 copper. The integrated IS pin allows the BCM (body control module) to detect open-filament and short-to-ground faults without a separate shunt, replacing the legacy relay + fuse + wiring harness with a single semiconductor switch. Reverse-battery protection up to -28 V eliminates the inline diode typically required for bulb protection.
おすすめ
12 V Relay and Solenoid Replacement
The BTS500801TEAAUMA1 directly replaces mechanical relays in 12 V body electronics applications such as door locks, seat adjusters, and mirror heaters. With integrated current limiting and active clamp, it absorbs the inductive kick from solenoid coils at turn-off without external freewheeling diodes, reducing PCB area and BOM cost. The IS pin provides closed-loop current monitoring for stall detection in motorized seat applications, while the wide 4.5 V to 28 V operating range handles cranking transients down to 6 V and load-dump spikes up to 28 V common in automotive electrical systems.
おすすめ
Interior LED Lighting Module Driver
For interior ambient lighting and LED reading lamps, the BTS500801TEAAUMA1 provides PWM-able high-side drive with millisecond response time, allowing brightness control via direct microcontroller PWM at 100-200 Hz without external gate drivers. The 10 milliohm RDS(on) keeps conduction losses negligible even at typical LED string currents of 1-3 A, and the diagnostic IS pin can detect LED open-circuit failures for lamp-out indication required by automotive safety standards. The PG-TO252-5-11 footprint fits compact LED driver PCBs and dissipates the modest I²R losses without heatsinking.
おすすめ
Automotive Body Control Module (BCM) Load Driver
The BTS500801TEAAUMA1 serves as a building block in BCMs, where multiple high-side switches control exterior lamps, horn, wipers, and accessory loads from a single ECU. The device's diagnostic IS output enables per-channel fault reporting back to the BCM microcontroller, supporting OBD-II lamp-out detection required by FMVSS and ECE regulations. With 10 A continuous rating per channel and 28 V load-dump survival, the BTS50080-1TEA family can drive most 12 V body loads directly, eliminating the discrete MOSFET + driver + TVS + shunt resistor circuit in each channel.
おすすめ
Industrial 24 V Actuator and Valve Driver
Although nominally a 12 V PROFET, the BTS500801TEAAUMA1's 28 V maximum supply rating allows operation on industrial 24 V systems with adequate derating. It drives solenoid valves, small pneumatic actuators, and 24 V relay coils with the same protections as in 12 V automotive use: over-current, over-temperature, and active clamp for inductive loads. The 4-pin DPAK footprint is widely supported by industrial PCB assembly lines, and the IS pin supports predictive maintenance by reporting actuator current back to the PLC for stuck-valve detection.
おすすめ
12 V Heated Seat and Mirror Heater Driver
The BTS500801TEAAUMA1 drives resistive heating loads such as seat heaters and exterior mirror heaters, where currents of 5-10 A are typical for fast warm-up. Its integrated current limit protects against heater-element shorts to ground, a critical safety function in seat applications. The diagnostic IS pin allows the climate-control module to detect heater failures and disable the channel. The PG-TO252-5-11 drain tab, when soldered to a 1 square inch copper pour, sustains continuous 10 A operation with junction temperature rise well within the 150 C rating under seat-cushion ambient conditions.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: BTS500801TEAAUMA1 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | BTS50080-1TEA | BTS500801TEBAUMA1 | BTS500801TMAATMA1 | BTS500801TMBAKSA1 | BTS500551TMBAKSA1 | VN5E016MH-E |
|---|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon | STMicroelectronics |
| Package | PG-TO252-5-11 (DPAK-5) | PG-TO252-5-11 (DPAK-5) - same | PG-TO252-5-11 (DPAK-5) - same | PG-TO252-5-11 (DPAK-5) - same | PG-TO252-5-11 (DPAK-5) - same | PG-TO252-5-11 (DPAK-5) - same | PG-TO252-5-11 (DPAK-5) - same |
| Nominal Supply Voltage | 12 V | 12 V | 12 V | 12 V | 12 V | 12 V | 12 V |
| Load Supply Range | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 16 V |
| Current Sense (IS pin) | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Automotive Qualified | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
主な差別化要因
- Same package and pinout as the entire BTS50080-1TEA family （vs BTS500801TEBAUMA1)
- 10 A continuous current in the standard PROFET 12V family （vs BTS500551TMBAKSA1)
- 28 V load-dump tolerance vs 16 V on cross-brand equivalents （vs VN5E016MH-E)
設計ノート
Estimated thermal analysis: at 10 A continuous load with 10 milliohm RDS(on), the device dissipates roughly 1 W (I² x R = 10² x 0.01). The PG-TO252-5-11 package's drain tab should be soldered to a PCB copper pour of at least 1 square inch (approximately 6 cm²) on the top or bottom layer to keep junction temperature rise within 50 C above ambient. Without sufficient copper, RDS(on) increases with temperature and the part may not sustain 10 A continuously. For high-ambient (>85 C) under-hood applications, use multiple thermal vias under the tab to spread heat to inner copper planes.
Place the device's drain tab on a copper pour connected to the load output; the drain tab is internally the drain node of the MOSFET. Keep the high-current load trace wide (at least 0.1 inch / 2.5 mm per ampere) and short to minimize parasitic inductance that could cause voltage ringing during PWM switching. The IS pin trace should be kept away from the IN/OUT switching traces to avoid capacitive coupling that distorts the sense current signal.
Do not connect the IS pin directly to a microcontroller ADC input - always use an external sense resistor to ground. The IS pin sources current (it is not a voltage output); attempting to read it with a high-impedance ADC without a sense resistor will produce undefined readings. Also, verify the IS pin's sense ratio (typically 1:5000 to 1:10000) from the datasheet before designing the fault-detection thresholds, as the ratio varies with junction temperature and load current. Reverse-battery protection is integrated, but do not exceed -28 V on the IN pin.
For PWM dimming of LED loads, switch the device at frequencies between 100 Hz and 1 kHz to avoid audible noise while maintaining good dimming resolution. The IS pin can be used to implement closed-loop current regulation by reading the sense voltage, computing the load current, and adjusting the PWM duty cycle accordingly - this compensates for LED forward-voltage variation with temperature. Place a 100 nF decoupling capacitor close to the IN pin to suppress supply transients during switching.
コンプライアンス情報
RoHS and REACH compliant per Infineon product page. AEC-Q100 qualified for automotive applications per the BTS50080-1TEA family datasheet. Halogen-free status not explicitly stated in the provided data.
