C8051F060-GQ - 25MHz 8051 MCU with Dual ADCs | SiLabs
部品番号: C8051F060-GQ ✓ 生産中C8051F060-GQ 概要
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals on one device. The C8051F060 belongs to the 8051 family of 8-bit microcontrollers and extends the conventional architecture with the Silicon Labs CIP-51 core. Its mixed-signal system-on-chip position places analog-to-digital conversion, general-purpose I/O, communications, and embedded control functions within a single package.
The headline features of this device include a 25 MHz operating frequency, 64 KB of in-system programmable flash, and 59 general-purpose digital I/O pins. Two separate 16-bit successive-approximation ADCs operate at up to 1 Msps, allowing the MCU to sample multiple analog channels for industrial controls, instrumentation, and embedded measurement systems. The operating-temperature range is -40°C to +85°C, while the 3.3 V supply class supports integration with common industrial and embedded electronics.
The C8051F060-GQ is part of the C8051F06x family, whose devices include four enhanced 8-bit ports and a 3-bit port for a total of 59 general-purpose I/O pins. Its integrated CAN controller supports industrial networking, while the dual ADC architecture reduces the need for external converters when several analog quantities must be measured. The 100-pin TQFP package provides enough pins for mixed analog, digital, and communications routing, although its relatively large footprint demands careful PCB planning.
Typical applications include sensor instrumentation, industrial data acquisition, CAN-connected machine controls, motor and actuator supervision, laboratory measurement equipment, and CAN-based industrial gateways. The combination of two fast ADCs and 59 I/O pins is particularly useful when a controller must capture analog inputs, operate digital sensors, and communicate over a robust industrial bus without relying on several discrete components.
For PCB implementation, reserve the manufacturer-recommended decoupling and analog-layout geometry around the power and ADC pins. Keep analog signal paths short, separate sensitive analog inputs from high-current switching nodes, and provide adequate exposed-board copper beneath the TQFP footprint for heat dissipation. Firmware and peripheral configuration should be validated against the Silicon Labs C8051F06x data sheet before production release.
ドロップイン代替品: C8051F060-GQ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: C8051F060-GQ (同一形状・フットプリント) — 相違点: Package, ADC Resolution, Flash Memory, Microcontroller Type, Processor Core.
C8051F062-GQ
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
C8051F064-GQ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
C8051F066-GQ
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
C8051F060-GQ 最大定格&電気的特性
| Product Type | 8-bit mixed-signal microcontroller |
| Core | 8051-compatible CIP-51 core |
| Maximum CPU Frequency | 25 MHz |
| Flash Memory | 64 KB |
| Program Memory Organization | 64K x 8 bits |
| RAM | 4,352 bytes (4,096 + 256 bytes) |
| General-Purpose Digital I/O | 59 pins |
| ADC Quantity | 2 |
| ADC Resolution | 16 bits |
| ADC Sampling Rate | Up to 1 Msps per ADC |
| ADC Type | Successive-approximation ADC |
| Communications | CAN |
| 動作温度範囲 | -40°C to +85°C |
| Supply Voltage Class | 2.7 V to 3.6 V |
| パッケージ | 100-pin TQFP, 14 mm x 14 mm |
| 実装タイプ | Surface mount |
| In-System Programming | Supported |
| Program Memory Type | Flash |
C8051F060-GQ 100-pin tqfp, 14 mm x 14 mm ピン配置ガイド
C8051F060-GQ (100-pin tqfp, 14 mm x 14 mm パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: C8051F060-GQ.
詳細は データシート をご参照ください。
主な用途
C8051F060-GQ の用途: 6 件s: Industrial Sensor Acquisition, CAN-Connected Machine Control, Precision Test and Measurement, CAN-Based Industrial Gateway, Motor and Actuator Supervision, Embedded Environmental Monitoring.
Industrial Sensor Acquisition
The C8051F060-GQ fits multi-channel industrial sensor acquisition because it combines two 16-bit ADCs operating at up to 1 Msps with 59 digital I/O pins. Separate converters can sample related analog inputs without relying on a multiplexed external converter, while the digital ports handle sensors, threshold inputs, and control outputs. Its 25 MHz CIP-51 core provides useful processing bandwidth for calibration, filtering, and converting measurements into protocol data. The -40°C to +85°C range supports industrial equipment when analog traces are properly shielded and the PCB follows the manufacturer grounding and decoupling layout.
おすすめ
CAN-Connected Machine Control
The C8051F060-GQ is suitable for CAN-connected machine controllers that must execute a control function and exchange diagnostic or process data. Its CAN interface supports network communication, while 59 I/O pins provide substantial capacity for inputs, outputs, interlocks, and actuator drivers. The 25 MHz core allows the firmware to scan I/O, apply control rules, and service communication events without moving basic control into a separate host processor. System designers should define termination, isolation, and grounding for the CAN physical layer while keeping the MCU supply and analog sections away from high-current switching nodes.
おすすめ
Precision Test and Measurement
The dual 16-bit, 1 Msps ADCs make the C8051F060-GQ useful in compact test and measurement instruments that acquire analog quantities and perform local calculations. Its 64 KB flash provides room for calibration tables, conversion routines, and instrument control logic, while 4,352 bytes of RAM supports acquisition buffers and working variables. The 59-pin digital interface can support range selection, front-panel control, relay logic, and status reporting. For laboratory accuracy, use guarded analog routing, clean references, appropriate input conditioning, and calibration procedures that account for the selected ADC and gain configuration.
おすすめ
CAN-Based Industrial Gateway
The C8051F060-GQ can serve as the local controller in a CAN-based industrial gateway that reads sensors, manages discrete I/O, and forwards converted data. Its mixed-signal architecture reduces the number of external components required when the gateway also monitors analog equipment. The 25 MHz core is suitable for protocol formatting and supervisory logic, while CAN connectivity supports communication with controllers on the same network. For a reliable gateway, isolate external field wiring where required, use robust power regulation, validate CAN bus timing, and program brownout and watchdog behavior for unattended operation.
おすすめ
Motor and Actuator Supervision
The C8051F060-GQ fits supervisory controllers for motors and actuators that require both digital command signals and analog feedback. Its 59 I/O pins can accept limit switches, position indicators, interlocks, and fault signals, while the dual 16-bit ADCs can monitor current, temperature, or position-sensor analog outputs. The 25 MHz core supports rapid state-machine updates and protection handling around the 1 Msps conversion capability. Direct power-stage routing remains critical: use suitable gate drivers and protection components, separate switching returns from analog references, and keep the MCU ground strategy consistent with the power converter.
おすすめ
Embedded Environmental Monitoring
The C8051F060-GQ is appropriate for an embedded environmental-monitoring station that samples multiple analog channels and manages digital probes. Two independent 16-bit ADCs can capture sensor outputs at up to 1 Msps, enabling time-aligned measurements or simultaneous sampling strategies. The 59 I/O pins support rain, temperature, door, power, and alarm inputs, while CAN or serial interfaces can link the station to a larger control network. For reliable field operation, protect external sensor inputs from surges, use filtered supplies, calibrate channels in software, and include watchdog and communications-failure recovery in the firmware design.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: C8051F060-GQ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | C8051F062-GQ | C8051F064-GQ | C8051F066-GQ |
|---|---|---|---|---|
| Package | 100-TQFP (14x14) | 100-TQFP (14x14) | 100-TQFP (14x14) | 100-TQFP (14x14) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| CPU Core | 8051-compatible CIP-51 | 8051-compatible CIP-51 | 8051-compatible CIP-51 | 8051-compatible CIP-51 |
| Maximum CPU Frequency | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB |
| RAM | 4,352 bytes | 4,352 bytes | 4,352 bytes | 4,352 bytes |
| Digital I/O | 59 pins | 59 pins | 59 pins | 59 pins |
| ADC Configuration | Two 16-bit ADCs, up to 1 Msps | Two 16-bit ADCs, up to 1 Msps | Two 16-bit ADCs, up to 1 Msps | Two 16-bit ADCs, up to 1 Msps |
| Communications | CAN | CAN | CAN | CAN |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
| Program Memory Type | In-system programmable flash | In-system programmable flash | In-system programmable flash | In-system programmable flash |
主な差別化要因
- Dual integrated high-resolution ADCs (vs C8051F064-GQ)
- Large digital control capacity in one package (vs C8051F062-GQ)
- Integrated CAN with deterministic control capability (vs C8051F066-GQ)
設計ノート
Place the required power-decoupling capacitors close to the device power pins and follow the manufacturer TQFP land pattern exactly. Route analog inputs directly from their connectors to the associated ADC pins with short traces and a continuous return path. Keep switching-regulator traces, motor outputs, and high-current return paths away from the analog section. The 100-pin package offers substantial routing flexibility, but correct decoupling and analog isolation remain more important than minimizing total board area.
Treat the two ADC signal paths as separate analog channels and verify input range, source impedance, acquisition time, and the selected gain configuration in the device documentation. Add appropriate input filtering where sensor outputs are noisy, but maintain the impedance and settling requirements for 16-bit conversion. For measurements requiring tight timing relationships, use the dual converters coherently and validate channel skew with calibrated equipment before production.
Do not treat a matching 100-pin TQFP footprint as proof that every C8051F06x member has identical behavior. Before replacing the C8051F060-GQ with C8051F062-GQ, C8051F064-GQ, or C8051F066-GQ, compare pin multiplexing, analog-channel assignments, interrupt sources, peripheral availability, clock requirements, and device identifiers in the Silicon Labs data sheet. Rebuild and retest firmware with the selected alternate rather than assuming binary compatibility.
Provide continuous copper beneath the TQFP footprint where the land pattern permits it and avoid long exposed-heat-pad routes through narrow thermal spokes. Keep regulators and other heat sources physically separated from the MCU and analog components when enclosure temperatures are high. Validate the assembled design at the maximum expected ambient temperature because 25 MHz processing, ADC activity, and external interface activity all contribute to board-level thermal conditions.
コンプライアンス情報
The manufacturer data sheet and product listings do not explicitly establish the requested compliance attributes for C8051F060-GQ.