CC1120RHBT - Sub-1GHz RF Transceiver, +16dBm | Texas Instruments
部品番号: CC1120RHBT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $6.3 | $6.30 |
| 10 | $5.8 | $58.00 |
| 100 | $5.2 | $520.00 |
| 500 | $4.7 | $2,350.00 |
| 1,000 | $4.2 | $4,200.00 |
CC1120RHBT 概要
A narrowband RF transceiver is an integrated radio chip that transmits and receives wireless data in narrow frequency channels, typically within the industrial, scientific, and medical (ISM) and short range device (SRD) bands. Within the wireless system hierarchy, a transceiver sits between the host microcontroller and the antenna, combining a low-IF or zero-IF receiver, a fractional-N synthesizer, and a power amplifier into a single power management and connectivity IC.
Key differentiating features include fully integrated channel filters that remove the need for costly external SAW and IF filters, exceptionally high receiver selectivity for operation in dense RF environments, and link budgets that support multi-kilometre range at narrow channel spacing. The device supports Wireless M-Bus (S, C, and N modes) and proprietary protocols, and offers low-power and low-voltage operation for cost-effective wireless systems.
Architecturally, the CC1120 integrates a low-IF receiver with high dynamic range, programmable narrowband filters, and an enhanced FIFO-based packet engine with an extended SPI interface for radio control. The integrated fractional-N PLL synthesizer covers all four frequency bands without external VCO components, and RSSI and link-quality indicators support channel assessment for frequency-agile network stacks.
Typical applications include smart metering (Wireless M-Bus), industrial remote control and telemetry, 169/433/868/915 MHz ISM sensor networks, and home/building automation where strong blocking performance and long range are required.
When designing, note that narrowband operation demands accurate crystal references; a low-phase-noise TCXO is often warranted for channels narrower than 12.5 kHz.
This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet, based on data verified as of 2026-10-19.
ドロップイン代替品: CC1120RHBT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CC1120RHBT （同一形状・フットプリント） — 相違点: Package, Integrated Filters, Modulation, Product Type, RF Family / Standard.
クイック比較ツール — 並列比較する代替部品を選択:
CC1120RHBR
✅ ドロップイン✓ 在庫あり
$1.52 / 個
データシートを見る →CC1121RHBT
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →CC1125RHBT
✅ ドロップイン✓ 在庫あり
$2.78 / 個
データシートを見る →CC1120RHMR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
CC1120RHBT 仕様
| RF Band | General ISM < 1 GHz |
| Frequency Range | 164 MHz to 192 MHz, 274 MHz to 320 MHz, 410 MHz to 480 MHz, 820 MHz to 960 MHz |
| Modulation | 2FSK, GFSK, OOK |
| Maximum Output Power | +16 dBm |
| Receiver Sensitivity | -123 dBm (low data rate) |
| Maximum Data Rate | 200 kbps |
| Protocol Support | Proprietary, Wireless M-Bus (S, C, N mode) |
| パッケージ | 32-VFQFN Exposed Pad (RHB) |
| 実装タイプ | Surface Mount |
| インターフェース | SPI |
| 電源電圧 | 2 V to 3.6 V |
| 動作温度 | -40C to +85C |
| RoHS ステータス | Compliant |
| Built-in MCU | No (transceiver, host controlled) |
| RF Family / Standard | General ISM < 1GHz |
| External Filters | Not required (integrated channel filters) |
CC1120RHBT 32-vfqfn exposed pad (rhb) ピン配置ガイド
CC1120RHBT (32-vfqfn exposed pad (rhb) パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: CC1120RHBT.
詳細は データシート をご参照ください。
主な用途
CC1120RHBT の用途: 6 件s: Smart Metering (Wireless M-Bus), Industrial Telemetry and Remote Control, 169 MHz / 433 / 868 / 915 MHz Sensor Networks, Home and Building Automation, Alarm and Security Systems, Long-Range Narrowband Data Links.
Smart Metering (Wireless M-Bus)
The CC1120RHBT is purpose-built for Wireless M-Bus smart metering in S, C, and N modes. Its integrated narrowband channel filters deliver the high selectivity required to operate in congested 169 MHz and 868 MHz metering bands, while receiver sensitivity down to -123 dBm provides the link budget needed to reach meters in basements and metallic enclosures. In a typical meter node, the CC1120 sits behind the meter MCU over SPI, with the differential RF_N/RF_P outputs feeding a discrete or integrated matching network to a 169 MHz or 868 MHz antenna. Because all channel filtering is on-chip, no external SAW filters are needed at the IF, reducing BOM cost. Design consideration: use a TCXO reference for N-mode narrowband channels to keep frequency error within the sub-band mask over the full -40C to +85C temperature range.
おすすめ
Industrial Telemetry and Remote Control
In industrial telemetry - tank level monitoring, crane and gate remote control, and machine status reporting - the CC1120RHBT provides robust links in electromagnetically noisy plants. Its high blocking and selectivity performance rejects interference from variable-frequency drives and welding equipment, and OOK/2FSK modulation support matches legacy industrial radio protocols for retrofit projects. The 410-480 MHz and 820-960 MHz band coverage lets one PCB design serve regional frequency plans. The device's 200 kbps capability supports fast command channels while narrowband operation preserves coexistence with licensed users. The exposed-pad VQFN-32 offers a solid RF ground for reliable performance across vibration and temperature extremes. A typical design pairs the transceiver with an MCU implementing redundant packet acknowledgement, using GPIO interrupts for FIFO and packet-status signaling to keep latency predictable.
おすすめ
169 MHz / 433 / 868 / 915 MHz Sensor Networks
Sub-GHz mesh and star sensor networks benefit from the CC1120RHBT's combination of -123 dBm sensitivity and +16 dBm output, which yields multi-kilometre line-of-sight range at narrow channel bandwidths. The four-band coverage (164-192, 274-320, 410-480, 820-960 MHz) means a single hardware platform can be certified for North America (915 MHz), Europe (868 MHz), and Asia (433 MHz) with firmware changes only. RSSI and link-quality indicator outputs support dynamic channel selection in frequency-agile stacks. Battery-powered sensor nodes exploit the low-voltage 2-3.6 V operation and low standby current, waking over SPI only for scheduled transmissions. Layout care is important: keep the differential RF path matched to 50 ohms per the TI reference design and place a solid ground plane under the exposed pad to stabilize VCO performance at the band edges.
おすすめ
Home and Building Automation
Home and building automation systems - door locks, smoke detectors, blinds control, and HVAC sensors - use the CC1120RHBT where penetration through concrete and metal-framed walls matters more than data rate. Sub-GHz propagation at 868/915 MHz outperforms 2.4 GHz in building interiors, and the CC1120's selectivity keeps coexisting networks separated at 12.5 kHz channel spacing. OOK mode supports ultra-low-power wake channels: a low-cost OOK receiver can wake the main node, which then activates the CC1120 for a high-reliability FSK data exchange. The integrated packet engine with FIFOs offloads framing from the host MCU, allowing 8-bit controllers to manage the network. Design trade-off: at +16 dBm the PA draws significant current, so schedule transmissions and use adaptive output power per the TI datasheet power tables to maximize battery life.
おすすめ
Alarm and Security Systems
Wireless alarm panels, panic transmitters, and gateways rely on the CC1120RHBT's combination of range and message integrity. The -123 dBm sensitivity guarantees alarm delivery from remote perimeters where received signal levels fall below typical transceivers' floors, and the high selectivity prevents false loss of link in RF-dense urban environments. The 200 kbps maximum rate comfortably handles encrypted alarm frames with per-packet authentication overhead. Two-way communication with channel blacklisting - enabled by the RSSI and LQI readouts - allows the gateway to steer around jamming or interference, an important anti-tamper feature in security products. Regulatory compliance across 433, 868, and 915 MHz bands lets manufacturers build one radio platform for global security markets. The VQFN-32 exposed pad also aids EMC performance, keeping spurious emissions within EN 300 220-style masks when layout follows the TI reference design.
おすすめ
Long-Range Narrowband Data Links
Point-to-point and point-to-multipoint narrowband links - weather stations, reservoir monitoring, agricultural gateways - exploit the CC1120RHBT's headline strength: a very high link budget at narrow bandwidths. Combining +16 dBm transmit power with -123 dBm sensitivity gives roughly 139 dB of raw link budget, enough for tens of kilometres line-of-sight with proper antennas, or reliable non-line-of-sight service in difficult terrain. Narrow channels such as 12.5 kHz or 6.25 kHz concentrate energy and reject broadband interference, and the integrated synthesizer tunes across the 274-320 MHz and 410-480 MHz windows licensed for telemetry in many countries. When more range is required, the pin-compatible CC1125 upgrades output to +27 dBm on the same footprint, and the CC1190 front-end adds a PA/LNA stage to the CC1120 with a matched-reference layout from TI.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CC1120RHBT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CC1120RHBR | CC1121RHBT | CC1125RHBT |
|---|---|---|---|---|
| Package | VQFN-32 (RHB) | VQFN-32 (RHB) - same | VQFN-32 (RHB) - same | VQFN-32 (RHB) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Type | Transceiver | Transceiver | Transceiver | Transceiver |
| Max Output Power | +16 dBm | +16 dBm | +16 dBm (higher PA class) | +27 dBm (868/915 MHz) |
| Receiver Sensitivity | -123 dBm | -123 dBm | -123 dBm | -129 dBm |
| Frequency Bands | 164-192 / 274-320 / 410-480 / 820-960 MHz | Same bands | Same bands | 169 / 410-480 / 820-960 MHz |
| Packaging Option | Tray (RHBT) | Tape & Reel (RHBR) | Tray (RHBT) | Tray (RHBT) |
| Protocol Support | Proprietary, Wireless M-Bus (S, C, N) | Proprietary, Wireless M-Bus (S, C, N) | Proprietary, Wireless M-Bus | Proprietary, Wireless M-Bus |
主な差別化要因
- Highest selectivity and blocking performance in the TI sub-1 GHz family （vs CC1125RHBT)
- External SAW/IF filters eliminated （vs CC1120RHBR)
- Tray packaging for prototyping and manual assembly （vs CC1120RHBR)
設計ノート
Solder the exposed thermal pad of the VQFN-32 (RHB) package to a grounded PCB pad with an array of thermal vias - this pad is the primary RF ground for the VCO and PA. Follow the TI CC1120 reference design layout: keep the differential RF_N/RF_P matching network compact, symmetric, and routed on the top layer with a solid ground plane beneath. Do not route digital SPI traces under the RF matching network. Place the 40 MHz crystal within 5 mm of the XOSC pins with short, symmetric traces and load capacitors sized per the crystal datasheet to hit the target load capacitance.
Supply the CC1120 from a clean 2-3.6 V rail; the PA at +16 dBm draws peak current in the range of tens of milliamps per TI reference designs, so decouple each VDD pin with 100 nF close to the pin plus a bulk 10 uF per the reference design BOM. Estimated: a metering node transmitting 10 ms packets every 10 s at +16 dBm averages well under 1 mA with the radio otherwise in IDLE or SLEEP, but battery sizing should use the datasheet current-consumption tables for your exact settings rather than this estimate.
Narrowband channels expose frequency-reference error: a standard +/-10-20 ppm crystal can shift the carrier out of a 6.25 kHz or 12.5 kHz channel mask over temperature, causing sensitivity loss or regulatory non-compliance. Use a TCXO (about +/-0.5 to +/-2 ppm) for channels narrower than 25 kHz. Also note the CC1120 is host-controlled - budget MCU SPI bandwidth and GPIO timing for FIFO servicing in your firmware, and verify antenna matching (50 ohm) with a VNA rather than copying reference design values to a different stack-up.
コンプライアンス情報
RoHS compliant per TI product data. Lead-free matte-finish VQFN package. REACH and conflict-minerals declarations should be obtained from TI's compliance portal.
