TPS63070RNMT - 2V-16V, 2A Buck-Boost Converter | TI
部品番号: TPS63070RNMT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.2 | $3.20 |
| 10 | $2.88 | $28.80 |
| 100 | $2.35 | $235.00 |
| 500 | $1.95 | $975.00 |
| 1,000 | $1.62 | $1,620.00 |
| 3,000 | $1.4 | $4,200.00 |
TPS63070RNMT 概要
A buck-boost converter is a type of DC-DC switching regulator within the broader power management IC category that combines buck (step-down) and boost (step-up) topologies. This lets a single inductor-based stage produce a stable rail from sources such as 4-cell alkaline, 12V lead-acid, or solar inputs whose voltage swings across the output level. The TPS63070 belongs to the switching voltage regulator family used in portable, industrial, and IoT power systems.
Key features include a 3.6A switch current limit, 2.4MHz switching frequency, and low quiescent current of approximately 50uA typical. Synchronous rectification with integrated MOSFETs improves efficiency and reduces external component count, while the 2.4MHz clock permits small inductors and capacitors for a compact footprint. PWM mode maximizes heavy-load efficiency and PFM mode preserves light-load efficiency; the device also supports negative output current sinking in PWM mode per TI datasheet SLVSDD7B.
Architecture-wise, the four-switch synchronous buck-boost topology seamlessly transitions between buck, buck-boost, and boost operating regions with a single inductor, avoiding output discontinuity when the battery voltage crosses the setpoint. The adjustable feedback (FB) pin sets the output with a resistor divider, and programmable soft-start limits inrush current.
Typical applications include battery-powered portable instruments, industrial sensors, IoT wireless nodes, and 12V rail conditioning for microcontrollers, RF modules, and displays. Wide input tolerance makes it ideal for solar or vehicle-supplied systems.
For best results, keep the inductor and input/output capacitor loops short, place the input capacitor at VIN and PGND, and provide adequate copper on the thermal pad. Pricing references are as of 2026-08-28.
ドロップイン代替品: TPS63070RNMT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TPS63070RNMT （同一形状・フットプリント） — 相違点: Input Voltage Range, Operating Temperature, Output Type, Output Voltage Range, Package.
クイック比較ツール — 並列比較する代替部品を選択:
TPS63070QRNMTQ1
✅ ドロップイン✓ 在庫あり
$2.49 / 個
データシートを見る →TPS63070RNMR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS630701RNMR
⚡ 同一パッケージ ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS630702RNMR
⚡ 同一パッケージ ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS63070QNMRQ1
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS63070RNMT 最大定格＆電気的特性
| トポロジー | Buck-Boost (synchronous) |
| 入力電圧範囲 | 2 V to 16 V |
| 出力電圧範囲 | 2.5 V to 9 V (adjustable) |
| Output Current | 2 A |
| Switch Current Limit | 3.6 A |
| スイッチング周波数 | 2.4 MHz |
| 出力数 | 1 |
| 出力タイプ | Adjustable (FB pin) |
| 動作温度 | -40C to +125C (TJ) |
| パッケージ | VQFN-HR (RNM), 15 pins |
| 実装タイプ | Surface Mount |
| 同期整流 | Yes (integrated MOSFETs) |
| Control Modes | PWM / PFM |
| ソフトスタート | Programmable |
| 熱シャットダウン | Yes |
| Negative Current Sinking | Supported in PWM mode |
TPS63070RNMT ピン構成
| ピン 1 | PGND — Power ground |
| ピン 2 | VIN — Power input, 2V-16V |
| ピン 3 | VINA — Analog supply for control circuit |
| ピン 4 | EN — Enable input |
| ピン 5 | SS/TR — Soft-start / tracking pin |
| ピン 6 | FB — Feedback, sets output with resistor divider |
| ピン 7 | PGND — Power ground |
| ピン 8 | SW1 — Switch node 1, connect inductor |
| ピン 9 | SW1 — Switch node 1 |
| ピン 10 | SW2 — Switch node 2, connect inductor |
| ピン 11 | SW2 — Switch node 2 |
| ピン 12 | VOUT — Regulated output, 2.5V-9V |
| ピン 13 | VOUT — Regulated output |
| ピン 14 | GND — Ground |
| ピン 15 | PGND — Power ground / thermal pad |
主な用途
TPS63070RNMT の用途: 6 件s: 12V Rail Conditioning for MCUs and RF Modules, Battery-Powered Portable Instruments, IoT Wireless Sensor Nodes, Solar-Powered Systems, Automotive 12V Subsystems, Display and LED Bias Supplies.
12V Rail Conditioning for MCUs and RF Modules
Industrial control boards often run from 12V or 24V rails that sag or spike across the 5V logic level. The TPS63070RNMT accepts 2V-16V input and regulates a stable 5V at up to 2A, passing seamlessly through buck, buck-boost, and boost regions without output dropout. Its 2.4MHz switching keeps inductors small, and synchronous rectification sustains high efficiency for always-on microcontroller and radio loads.
おすすめ
Battery-Powered Portable Instruments
Multi-cell alkaline or lithium battery packs swing from above to below the regulated rail as they discharge. The TPS63070RNMT's 2V-16V input and 2.5V-9V adjustable output maintain regulation across the entire discharge curve, while roughly 50uA quiescent current and PFM light-load mode extend battery life between charges or replacements in handheld test and measurement devices.
おすすめ
IoT Wireless Sensor Nodes
Wireless sensor nodes need burst-current capability for radio transmit while idling at microamp levels. The TPS63070RNMT supplies 2A peaks for PA bursts from a 2V-16V solar or battery source, and its PFM mode preserves efficiency at sleep-state loads. The 2.4MHz operation permits a compact inductor, fitting constrained node PCBs. Output set by a single FB resistor divider simplifies rail provisioning.
おすすめ
Solar-Powered Systems
Solar panel output voltage varies widely with irradiance and temperature, frequently crossing the battery or load voltage. The TPS63070RNMT's 2V-16V input range and automatic buck-boost transition deliver a constant output from dawn-to-dusk conditions without mode discontinuity, making it a simple single-inductor power stage for solar garden devices, remote telemetry, and energy-harvesting front ends.
おすすめ
Automotive 12V Subsystems
With the AEC-Q100 qualified TPS63070QRNMTQ1 sibling, this family serves automotive modules supplied from 12V battery rails that droop during cranking below 6V and surge during load dump. The wide 2V-16V input holds infotainment or sensor-module outputs steady through both conditions, and the 2.4MHz switching keeps switching noise out of the AM radio band, easing EMC compliance.
おすすめ
Display and LED Bias Supplies
Small TFT and OLED displays need stable 3.3V-9V rails from battery or USB inputs of varying voltage. The TPS63070RNMT regulates any setpoint in its 2.5V-9V range with 2A capability for display backlight drivers and panel logic. Integrated synchronous FETs and a 2.4MHz clock shrink the solution to a single small inductor, fitting slim display modules with tight height limits.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TPS63070RNMT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TPS63070QRNMTQ1 | TPS63070RNMR | TPS630701RNMR | TPS630702RNMR |
|---|---|---|---|---|---|
| Package | VQFN-HR (RNM) 15-pin | VQFN-HR (RNM) 15-pin - same | VQFN-HR (RNM) 15-pin - same | VQFN-HR (RNM) 15-pin - same | VQFN-HR (RNM) 15-pin - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Voltage Range | 2V to 16V | 2V to 16V | 2V to 16V | 2V to 16V | 2V to 16V |
| Output Voltage | 2.5V-9V adjustable | 2.5V-9V adjustable | 2.5V-9V adjustable | 3.3V fixed | 5V fixed |
| Output Current | 2 A | 2 A | 2 A | 2 A | 2 A |
| Switch Current Limit | 3.6 A | 3.6 A | 3.6 A | 3.6 A | 3.6 A |
| Switching Frequency | 2.4 MHz | 2.4 MHz | 2.4 MHz | 2.4 MHz | 2.4 MHz |
| AEC-Q100 Qualification | No (standard grade) | Yes | No | No | No |
| Packing | Cut tape / small reel (T) | Cut tape (T) | Tape & reel 3000 (R) | Tape & reel 3000 (R) | Tape & reel 3000 (R) |
主な差別化要因
- Widest input range in TI buck-boost family （vs TPS63021)
- Automotive-qualified drop-in sibling （vs TPS63070QRNMTQ1)
- Higher output current than small buck-boosts （vs TPS62740DSSR)
設計ノート
Place the input capacitor as close as possible to the VIN and PGND pins, and keep the SW1/SW2-to-inductor loop short and wide. The four-switch buck-boost topology circulates current through both switch nodes, so minimize the copper loop area of SW1-inductor-SW2 to limit radiated EMI at the 2.4MHz switching frequency. Follow TI datasheet SLVSDD7B Section 9 PCB layout guidelines.
The exposed thermal pad must be soldered to a solid ground plane with an array of thermal vias. At VIN=12V, VOUT=5V, 2A load, dissipation is roughly 1-2W depending on efficiency; inadequate copper can push the junction beyond the 125C rating. Use at least 1 square inch of 2oz copper or a buried ground plane under the pad for high-power continuous loads.
Do not omit the SS/TR soft-start capacitor; omitting it causes hard inrush at startup. Ensure the FB divider uses 1% resistors and the FB node is kept short to avoid noise pick-up. Verify the inductor saturation rating exceeds the 3.6A switch current limit - undersized inductors saturate and trigger current-limit instability.
コンプライアンス情報
RoHS compliance per distributor listings (DigiKey/LCSC). AEC-Q100 applies only to the TPS63070Q (Q1) variant, not this standard part. Verify REACH status on TI product page.
