CD4020AF3 - 14-Bit CMOS Binary Counter | Harris | DIP-16
部品番号: CD4020AF3 ✗ 生産終了CD4020AF3 概要
A binary ripple counter is a sequential digital circuit that divides an input clock by powers of two. The CD4020AF3 belongs to the CMOS logic hierarchy, where CMOS means complementary metal-oxide-semiconductor. CMOS counters provide a practical way to reduce a clock frequency while preserving a simple digital interface. The part can be used in designs requiring periodic events, elapsed-time measurement, waveform repetition, programmable timers, and low-frequency clock generation.
The CD4020AF3 uses a 16-pin DIP package, and distributor listings identify the device as a counter with a 14-bit count element. The CD4020 family is associated with the CD4000 CMOS logic series, a broad family historically used for low-power digital logic implementation. Exact operating voltage, current, timing, propagation-delay, maximum input frequency, and environmental limits must be confirmed in the manufacturer datasheet before a production design is released.
The AF3 ordering code identifies a particular Harris Corporation package and qualification configuration. Because availability and lifecycle status can differ between manufacturers, distributors, and legacy inventory channels, engineers should verify the exact package dimensions, temperature range, marking convention, and sourcing condition before placing an order. The CD4020AF3 is especially relevant to repair and redesign work where changing the PCB footprint is undesirable and a pin-compatible 16-pin counter is required.
Typical circuit roles include binary frequency division in clock-generation modules, event-counting stages in industrial controls, repetitive pulse timing in test equipment, and low-power sequencing in embedded systems. A practical design should include reset-state analysis, unused-input biasing, clock-edge selection, and output-decode logic appropriate to the intended count sequence.
This page combines the exact CD4020AF3 identity, package classification, sourcing information, application guidance, and pin-compatible replacement guidance. It also highlights the practical distinction between a true drop-in replacement and a merely similar counter: pin arrangement, count length, logic levels, supply range, timing, and qualification requirements must all match before substitution is appropriate.
For new designs, begin with the manufacturer datasheet and confirm the reset behavior, output states, operating limits, and absolute maximum ratings. For legacy equipment, evaluate the replacement in the complete system because timing margin and unused-pin treatment can affect reliability even when the physical footprint is unchanged.
ドロップイン代替品: CD4020AF3 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
CD4020BF3A
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD4020AF3 最大定格&電気的特性
| Product Type | Binary ripple counter IC |
| Logic Family | CD4000 CMOS series |
| Count Element | 14-bit |
| Package Type | DIP-16 |
| ピン数 | 16 pins |
| 実装タイプ | Through-hole |
| Manufacturer | Harris Corporation |
| RoHS ステータス | Compliant |
CD4020AF3 dip-16 ピン配置ガイド
CD4020AF3 (dip-16 パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: CD4020AF3.
詳細は データシート をご参照ください。
主な用途
CD4020AF3 の用途: 6 件s: Binary Clock Frequency Divider, Industrial Event Counter, Repetitive Pulse Generator, Legacy Instrumentation Retimer, Digital Sequencer and Timer, Educational Digital Logic Platform.
Binary Clock Frequency Divider
The CD4020AF3 is suitable for dividing a periodic input clock into slower binary-rate outputs in digital timing and control systems. Its 14-bit counter element provides multiple tap points, allowing one clock source to produce several related frequencies rather than requiring a separate divider for each timing interval. The 16-pin DIP package also simplifies insertion into legacy through-hole timing boards. Before implementation, verify the manufacturer timing table, reset behavior, and supply-voltage limits so that the divider remains within valid propagation-delay and operating conditions.
おすすめ
Industrial Event Counter
The CD4020AF3 can count recurring events when an external sensor or comparator produces clean, debounced pulses. A 14-bit counter stage gives the controller a compact way to accumulate pulses without requiring a microcontroller counter peripheral. In an industrial design, the pulse amplitude, clock transition timing, reset duration, and supply level remain critical. Confirm the electrical limits in the manufacturer datasheet and add proper input conditioning to prevent multiple counts from switch bounce or noisy transitions.
おすすめ
Repetitive Pulse Generator
When the CD4020AF3 counter output is fed back through suitable shaping logic, it can create a periodic pulse train with a programmable division ratio. This arrangement is useful in test fixtures, sequencers, and equipment that must repeat a control action at a lower rate than its master oscillator. The designer must account for propagation delay, reset synchronization, and any feedback-loop timing margin. Validate the maximum input frequency and output transition behavior in the manufacturer datasheet before setting the operating clock.
おすすめ
Legacy Instrumentation Retimer
The CD4020AF3 can divide a reference clock in laboratory or industrial instrumentation to obtain a slower timing base. A 14-bit counter offers numerous binary taps for selecting a divider interval, while the DIP-16 format supports repair of older through-hole boards. For instrumentation, use the counter with clean clocking and synchronous reset practices to prevent metastability near rollover. Confirm the device's operating limits, output-drive capability, and timing margin against the target reference frequency before production use.
おすすめ
Digital Sequencer and Timer
The CD4020AF3 can serve as the counting element of a multistage digital timer when its binary outputs feed combinational decode logic. This approach is useful where a simple fixed sequence must control lamps, relays, or acquisition stages without a microcontroller. Each decoded transition should be checked for rollover and reset hazards, and unused counter outputs should not be relied upon for timing accuracy. Use the datasheet's truth table and timing characteristics to define the reset window and maximum sequential-transition rate.
おすすめ
Educational Digital Logic Platform
The CD4020AF3 is useful in educational and prototype boards that demonstrate binary counting, ripple propagation, frequency division, and decoded timer states. Its visible through-hole DIP-16 package makes the sixteen connections accessible for wiring and measurement. The relevant learning checks include clock-edge behavior, reset priority, counter rollover, and propagation-delay accumulation across multiple stages. Because the exact operating limits are not stated in the indexed summaries, students and instructors should use the manufacturer datasheet before applying a specific supply voltage or clock rate.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CD4020AF3 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CD4020BF3A |
|---|---|---|
| Package | DIP-16 | DIP-16 |
| Brand | Harris Corporation | Harris Corporation |
| Product Type | Binary ripple counter | CD4020-family counter |
| Logic Family | CD4000 CMOS | CD4000 CMOS |
| Mounting Type | Through-hole | Through-hole |
主な差別化要因
- Exact legacy Harris catalog identity (vs CD4020BF3A)
- Confirmed 14-bit counter element (vs CD4020BF3A)
- Established DIP-16 migration path (vs CD4020BF3A)
設計ノート
Treat the clock input as a timing-critical node. Route it away from high-current switching nodes, provide a return path, and avoid long parallel branches that can increase capacitive loading and clock-edge distortion. If an external contact or comparator drives the clock, use Schmitt-trigger conditioning to prevent multiple transitions from noise or slow edges. Confirm the maximum input frequency and propagation-delay limits in the manufacturer datasheet before selecting the counter rate.
Do not assume that a CD4000 counter with a matching package is automatically interchangeable. Verify pin assignments, reset polarity and timing, count length, logic thresholds, operating voltage, propagation delay, temperature grade, and qualification status. Unused inputs must be held at a valid logic level according to the datasheet, while unused outputs should be left unconnected unless the circuit specifically requires them.
Keep the supply distribution short and decouple the counter close to its supply and ground pins with the capacitance and dielectric recommended by the manufacturer. A counter can experience transient current when multiple internal stages change during rollover, so adequate local decoupling helps prevent supply disturbance from shifting other digital nodes. For battery-powered equipment, evaluate both switching activity and quiescent consumption because the effective supply current depends on clock rate and logic-state activity.
Use the manufacturer's pin-1 indication and land pattern when installing a replacement in a through-hole board. Check row spacing, body length, lead diameter, and notch or dimple orientation against the actual socket or PCB footprint. Confirm that the reset path and clock path are not routed beneath long analog or switching sections where they could collect noise. For socketed legacy assemblies, verify the socket type and contact reliability rather than assuming every DIP-16 socket is mechanically identical.
コンプライアンス情報
RoHS compliance is stated in the indexed CD4000 DIP-16 counter listing. No additional compliance or qualification claim is established.