CD4051BMT - 8:1 CMOS Analog Multiplexer | Texas Instruments
部品番号: CD4051BMT ✓ 生産中CD4051BMT 概要
An analog multiplexer is a semiconductor switch that selects one input channel from several alternatives and connects it to a shared output. This 8:1 device belongs to the CD4000 CMOS logic family and is controlled by digital selection logic while carrying continuously varying analog signals. Its architecture makes it useful for channel selection, signal routing, test systems, data acquisition, and communication equipment where voltage, current, or impedance measurements must be directed selectively.
The CD4051BMT provides an 8:1 configuration, one analog channel, a 240 ohm nominal switch resistance as identified for this ordering variant, and 320 ns typical turn-on time. Its specified operating-temperature range is -55°C to +125°C, making it suitable for industrial and extended-temperature environments. The 16-SOIC package supports conventional surface-mount assembly while exposing separate supply and analog-signal terminals.
Its logic-level conversion capability allows address or command signals to be generated by digital control circuitry while the multiplexer routes the selected analog signal. The exact supported control-logic levels depend on the supply voltages applied to the device, so the selection inputs and inhibit input must be referenced to the correct supply domain. Charge injection, clock feedthrough, off-state leakage, bandwidth, and channel matching should be evaluated from the manufacturer datasheet for precision signal-chain designs.
Typical uses include routing multiple sensor inputs into one amplifier or ADC channel, sharing test equipment among several circuit nodes, selecting audio sources, controlling measurement paths, and implementing programmable signal-distribution systems. The extended temperature range and compact 16-pin package are useful in industrial instrumentation, though modern designs may require checking logic thresholds, signal bandwidth, and switching transients against the exact system requirements.
Designers should keep analog and digital return currents separated as far as practical, place decoupling close to the supply pins, and treat the inhibit and address inputs as ordinary CMOS logic rather than high-impedance analog nodes. Signal amplitude must remain within the device's permitted input and supply ranges. For ac applications, verify switching speed and off-state isolation before treating the multiplexer as a high-performance RF switch.
This product page combines the manufacturer and distributor specifications with practical routing, temperature, packaging, and replacement guidance. It also identifies where an existing design can use a pin-compatible 8:1 multiplexer and where supply-voltage, logic-level, or package differences require design review before substitution.
ドロップイン代替品: CD4051BMT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CD4051BMT (同一形状・フットプリント).
SN74LV4051ADR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD74HC4051E
✅ ドロップイン📋 参考代替品(カタログ未掲載)
HEF4051B
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CD4051BMT 最大定格&電気的特性
| Multiplexer Configuration | 8:1 |
| Number of Switched Channels | 1 channel |
| Maximum Supply Voltage | 20 V |
| Nominal On Resistance | 240 ohm |
| Listed On Resistance | 1050 ohm |
| Turn-On Time | 320 ns |
| Turn-Off Time | 210 ns |
| 動作温度範囲 | -55°C to +125°C |
| パッケージ | 16-pin SOIC (D) |
| 実装タイプ | Surface mount |
| Select Inputs | 3 binary select inputs |
| Inhibit Input | 1 inhibit input |
| Logic-Level Conversion | Supported |
| RoHS ステータス | Unknown |
| REACH Status | Unknown |
CD4051BMT ピン構成
| ピン 1 | IN4 — Analog input or output terminal 4 |
| ピン 2 | IN6 — Analog input or output terminal 6 |
| ピン 3 | IN5 — Analog input or output terminal 5 |
| ピン 4 | IN7 — Analog input or output terminal 7 |
| ピン 5 | VSS — Ground supply terminal |
| ピン 6 | E — Inhibit input |
| ピン 7 | IN3 — Analog input or output terminal 3 |
| ピン 8 | IN2 — Analog input or output terminal 2 |
| ピン 9 | IN1 — Analog input or output terminal 1 |
| ピン 10 | IN0 — Analog input or output terminal 0 |
| ピン 11 | OUT — Common analog output terminal |
| ピン 12 | VDD — Positive supply terminal |
| ピン 13 | A — Binary select input A |
| ピン 14 | B — Binary select input B |
| ピン 15 | C — Binary select input C |
| ピン 16 | VEE — Negative supply terminal |
主な用途
CD4051BMT の用途: 6 件s: Multichannel Sensor Signal Routing, Data Acquisition Front End, Industrial Test-System Signal Selection, Audio Source Selection, Programmable Signal Distribution, Instrumentation and Control Panels.
Multichannel Sensor Signal Routing
The CD4051BMT is suitable for routing several analog sensor outputs into one shared amplifier or converter channel. Its three select inputs can control eight source choices, and the listed 320 ns turn-on and 210 ns turn-off times support measurement systems that do not require high-bandwidth video multiplexing. The 20 V supply capability also permits operation above common low-voltage logic rails when the signal amplitudes and control thresholds are checked. Use separate returns and controlled grounding to prevent sensor excitation currents from modulating the selected channel, and verify the datasheet limits before routing low-level thermocouple or bridge signals.
おすすめ
Data Acquisition Front End
An 8:1 analog multiplexer can reduce the number of front-end input channels in a data-acquisition system by selecting one sensor at a time for a shared ADC path. The CD4051BMT provides the required 8:1 configuration, inhibit control, and 20 V maximum supply rating in a 16-pin SOIC package. Its -55°C to +125°C operating range supports extended-temperature acquisition equipment. Account for the 320 ns turn-on time during the acquisition settling interval and confirm bandwidth, charge injection, and off-state isolation against the measurement accuracy requirement.
おすすめ
Industrial Test-System Signal Selection
The CD4051BMT can connect multiple test nodes to a common measurement amplifier, allowing a compact fixture to sequence measurements without moving probes. Its 8:1 channel count reduces wiring complexity, while the inhibit input provides a convenient way to isolate the selected path during setup or reset. The extended -55°C to +125°C range is advantageous in industrial equipment, but the 240 ohm nominal on resistance may affect high-impedance sources. Use a low-input-impedance buffer when necessary and verify leakage, switching transients, and channel-to-channel behavior.
おすすめ
Audio Source Selection
The CD4051BMT can route one of eight audio-frequency sources to a shared output stage, making it useful in compact audio routing equipment. Its listed 320 ns and 210 ns switching transitions are much shorter than typical audio-band periods, while the 20 V supply rating offers flexibility in higher-voltage analog circuits. The 240 ohm nominal on resistance is acceptable for many line-level audio paths but can create loss with low-impedance loads. Confirm bandwidth, off-state isolation, distortion contribution, and click/noise behavior in the intended signal path before finalizing the design.
おすすめ
Programmable Signal Distribution
The CD4051BMT can act as a digitally addressed signal distributor when the multiplexer and demultiplexer functions are used in coordinated systems. Eight selectable analog terminals, three binary address inputs, and an inhibit control provide flexible routing controlled by standard digital logic. Its 16-pin SOIC package simplifies surface-mount assembly, while logic-level conversion supports interfacing with suitable control circuitry. Designers should establish valid input-output signal ranges, account for the 240 ohm nominal on resistance, and ensure that supply sequencing does not force undefined analog states onto externally connected equipment.
おすすめ
Instrumentation and Control Panels
The CD4051BMT is useful in instrumentation systems where multiple control or measurement lines must be selected before being applied to a shared actuator or indicator interface. Three address inputs and an inhibit function permit orderly routing and shutdown behavior, while the extended temperature range supports ruggedized equipment. The analog switch's on resistance and switching transient can affect the controlled signal, so buffer high-impedance or precision control nodes when required. Keep routing traces away from sensitive references and use the inhibit function to place outputs into a defined state during initialization.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CD4051BMT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SN74LV4051ADR | CD74HC4051E | HEF4051B |
|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Multiplexer Configuration | 8:1 | 8:1 | 8:1 | 8:1 |
主な差別化要因
- Higher maximum supply rating (vs SN74LV4051ADR)
- Extended-temperature CD4051B platform (vs CD74HC4051E)
- One-to-one 8:1 channel routing (vs HEF4051B)
設計ノート
Route the eight analog terminals and OUT as a compact, symmetrical signal network, and keep the three select traces away from high-impedance analog nodes. Place the supply-decoupling capacitor close to VDD with a short return path to VSS. Because the CD4051BMT is a CMOS analog switch, minimize parasitic capacitance on the selected channel and use a ground strategy that prevents input current from sharing the sensitive return path.
Do not treat the eight terminal names as permanently designated inputs or outputs; the multiplexer and demultiplexer functions depend on how the circuit is connected. Also do not assume that a 5 V logic-family substitute is equivalent in a 20 V circuit. Verify supply ratings, control thresholds, analog signal limits, inhibit polarity, and the selected package pinout before replacing CD4051BMT with SN74LV4051ADR, CD74HC4051E, or HEF4051B.
Allow the downstream acquisition or measurement circuit to settle after the 320 ns turn-on transition before taking a reading. For low-level or high-impedance signals, the listed 240 ohm nominal on resistance and unverified off-state leakage may dominate the error budget. Check bandwidth, charge injection, clock feedthrough, and isolation in the manufacturer datasheet, and use a buffer when the source impedance is high.
Decouple the supply pins locally and control the inhibit input during power-up so that externally connected signals do not receive an unintended transition. Observe the permitted signal and supply ranges for the selected operating mode. If VEE is connected, establish the negative rail reference correctly and confirm that every attached source remains within the permitted input range; the device must never be assumed to tolerate signals outside its supply-domain limits.
コンプライアンス情報
No explicit compliance declarations were identified for this ordering variant. AEC-Q100 status is not applicable to the stated industrial and extended-temperature product category rather than a confirmed qualification.