CY8C3866LTI-068 - 67MHz 8051 PSoC 3 MCU | Infineon
部品番号: CY8C3866LTI-068 ✓ 生産中CY8C3866LTI-068 概要
A PSoC, or programmable system-on-chip, is a mixed-signal microcontroller architecture that integrates an MCU core with configurable analog and digital functional blocks. PSoC 3 devices extend the 8051 instruction set with programmable peripherals, allowing designs to consolidate functions that would otherwise require separate analog, digital, and memory components. This integration can reduce board area, component count, and development effort.
The CY8C3866LTI-068 operates at up to 67 MHz and includes 64 KB of flash, 8 KB of SRAM, 1 KB of data EEPROM, and 8 KB of ECC flash according to the Keil device summary. Its 20-bit analog-to-digital converter supports precision measurements, while programmable digital blocks can implement timers, counters, serial interfaces, and other control functions without excessive fixed peripheral overhead.
The device uses an 8051-compatible single-core architecture and provides a Peripheral Hub Unit with eight parallel access paths. The Keil device summary identifies 27 interrupt sources with eight priority levels, plus dual data pointers and four flash protection levels. These features make the MCU suitable for embedded control systems that combine acquisition, control, communications, and data-retention requirements.
Typical applications include industrial sensor controllers, building automation modules, consumer appliances, motor and process-control equipment, and compact embedded instruments. The 48-QFN package supports dense PCB layouts, while the integrated analog and programmable digital resources allow a system to be implemented with fewer external components than a discrete microcontroller-plus-peripheral design.
PCB design should preserve the exposed-pad thermal and electrical requirements of the 48-QFN package, place decoupling capacitors close to the supply pins, and follow the manufacturer pin-description table when assigning signals. Firmware configuration also requires careful allocation of the programmable blocks, ADC resources, clocks, interrupts, and I/O pins in PSoC Creator.
This page consolidates the device identity, key memory and analog specifications, drop-in family alternatives, application guidance, and practical design considerations into an engineering-focused reference for evaluating and implementing the CY8C3866LTI-068.
ドロップイン代替品: CY8C3866LTI-068 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
CY8C3866LTI-068T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CY8C3866LTI-030
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CY8C3866LTI-068 最大定格&電気的特性
| Product Type | PSoC 3 programmable system-on-chip |
| Processor Core | 8051-compatible single core |
| CPU Maximum Frequency | 67 MHz |
| Architecture | 8-bit |
| Flash Memory | 64 KB (64K × 8 bits) |
| SRAM | 8 KB |
| Data EEPROM | 1 KB |
| ECC Flash | 8 KB |
| ADC Resolution | 20-bit |
| Supply Voltage Range | 0.5 V to 5.5 V |
| I/O Supply Voltage Range | 1.7 V to 5.5 V |
| パッケージ | 48-QFN, 7 mm × 7 mm |
| ピン数 | 48 pins |
| 実装タイプ | Surface mount |
| Interrupt Sources | 27 sources |
| Interrupt Priority Levels | 8 levels |
| Data Pointers | 2 |
| Flash Protection Levels | 4 levels |
| Peripheral Hub Unit | 8 parallel access paths |
CY8C3866LTI-068 48-qfn, 7 mm × 7 mm ピン配置ガイド
CY8C3866LTI-068 (48-qfn, 7 mm × 7 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: CY8C3866LTI-068.
詳細は データシート をご参照ください。
主な用途
CY8C3866LTI-068 の用途: 6 件s: Industrial Sensor Controller, Building Automation Module, Process Control Equipment, Consumer Appliance Control, Embedded Data Acquisition Unit, Motor and Valve Control.
Industrial Sensor Controller
The CY8C3866LTI-068 fits industrial sensor controllers that require high-resolution acquisition and responsive control from one mixed-signal device. Its 20-bit ADC can capture sensor signals, while the 8051-compatible core running up to 67 MHz supports filtering, calibration, and control logic. The 64 KB flash provides room for firmware and configuration data, while 8 KB of SRAM supports working buffers. Programmable PSoC 3 blocks can implement timers, communications, and digital interfaces around the measurement chain, reducing reliance on separate logic devices. Engineers should confirm the ADC input range, external signal-conditioning needs, and 48-QFN exposed-pad layout in the manufacturer documentation.
おすすめ
Building Automation Module
The CY8C3866LTI-068 is well suited to compact building-automation modules that monitor environmental inputs and control lights, valves, or networked peripherals. The 20-bit ADC supports precise readings from temperature, humidity, and occupancy sensors, while programmable digital resources can provide timing and serial communication functions. With 64 KB flash, 8 KB SRAM, 1 KB data EEPROM, and 8 KB ECC flash, it supports application firmware, configuration, and persistent parameters. Its 48-QFN 7 mm × 7 mm package helps reduce board area, although careful decoupling and exposed-pad layout remain essential in compact controllers. Firmware should be tested for interrupt latency, resource conflicts, and low-power behavior before field deployment.
おすすめ
Process Control Equipment
The CY8C3866LTI-068 supports process-control equipment that combines sensor acquisition with deterministic embedded logic. The 20-bit ADC is the primary analog resource, while the 67 MHz 8051-compatible core can execute control algorithms, diagnostics, and communication tasks. The 27 interrupt sources and eight priority levels allow multiple real-time events to be managed, and programmable PSoC blocks extend timer, counter, and serial-interface capabilities. Memory partitioning between 64 KB flash, 8 KB SRAM, 1 KB EEPROM, and 8 KB ECC flash allows firmware and operating data to be separated. For motor, valve, or heater loops, validate timing margins, output-driver requirements, isolation, and safety shutdown behavior in the final hardware.
おすすめ
Consumer Appliance Control
The CY8C3866LTI-068 can serve as the primary controller in a compact consumer appliance by combining an embedded MCU, configurable digital functions, and analog measurement resources. A 20-bit ADC may monitor sensors, potentiometers, or temperature inputs, while programmable blocks can offload timing and interface tasks from the core. The 64 KB flash accommodates control code and lookup data, and the 8 KB SRAM accommodates transient control state. The 48-QFN package reduces PCB footprint compared with larger leaded packages, supporting space-constrained appliance boards. Product engineers should still budget external drivers for loads, maintain short supply paths, and verify all signal levels against the device's stated operating ranges.
おすすめ
Embedded Data Acquisition Unit
The CY8C3866LTI-068 is appropriate for embedded data-acquisition units that need a compact processor, substantial flash, and high-resolution analog conversion. The 20-bit ADC supports precision measurement, while 8 KB of SRAM can hold acquisition buffers and 1 KB of EEPROM can preserve calibration or configuration values. The 8 KB ECC flash area offers additional protected storage, and the 27-source interrupt system can coordinate sampling, communication, and status events. The 8051 core at up to 67 MHz provides sufficient control bandwidth for preprocessing before data is transferred or logged. Designers should select suitable input protection, precision references, and external memory when acquisition volume exceeds the on-chip resources.
おすすめ
Motor and Valve Control
The CY8C3866LTI-068 can serve as the supervisory controller in a motor or valve-control subsystem where sensing, timing, and protection logic are required. Its programmable digital blocks can support timers, counters, and communication tasks, while the 20-bit ADC can monitor current, position, or temperature feedback. The 67 MHz core provides headroom for closed-loop calculations and diagnostics, and the 8 KB SRAM can hold motion-state information. The compact 48-QFN package is useful in dense control boards, but the final design must provide appropriate power stages, protection networks, and signal conditioning. Firmware and hardware validation should cover startup, stall, overcurrent, emergency-stop, and communications-failure scenarios.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CY8C3866LTI-068 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CY8C3866LTI-068T | CY8C3866LTI-030 |
|---|---|---|---|
| Package | 48-QFN (7 mm × 7 mm) | 48-QFN (7 mm × 7 mm) | 48-QFN (7 mm × 7 mm) |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Processor Core | 8051-compatible single core | 8051-compatible single core | 8051 core |
| Flash Memory | 64 KB | 64 KB | 64 KB |
| Ordering or Shipping Form | -068 tray form | -068T tape-and-reel form | -030 ordering suffix |
| Programmable Mixed-Signal Architecture | PSoC 3 with configurable analog and digital blocks | PSoC 3 with configurable analog and digital blocks | PSoC 3 with configurable analog and digital blocks |
主な差別化要因
- Direct same-package production alternative (vs CY8C3866LTI-068T)
- High-resolution mixed-signal integration (vs CY8C3866LTI-030)
- Compact 48-QFN implementation (vs CY8C3866LTI-068T)
設計ノート
Use the manufacturer 48-QFN land pattern and exposed-pad guidance when laying out the board. Place the required supply and decoupling capacitors close to their associated pins, keep the exposed-pad connection electrically and thermally compliant with the package documentation, and avoid high-current or high-speed routing beneath sensitive analog inputs. The target package is 7 mm × 7 mm, so assembly tolerances and the exposed-pad thermal path should be reviewed before fabrication.
Separate core and I/O supply requirements into the schematic and power-budget review. The listed supply range is 0.5 V to 5.5 V, while a related listing identifies a 1.7 V to 5.5 V I/O range; do not infer that every supply domain can operate at 0.5 V. Confirm sequencing, voltage tolerances, and decoupling requirements for each configured power rail in the manufacturer electrical-characteristics tables.
Do not treat multifunction pins as ordinary GPIO without checking the device configuration. Infineon Developer Community material identifies pins 7, 8, and 10 as multifunction in a PSoC 3 design context, illustrating how programming or debug functions can affect GPIO use. Assign signals from the manufacturer pin-description table and verify the final PSoC Creator configuration against the schematic to prevent boot, programming, or peripheral conflicts.
Keep analog acquisition paths away from switching nodes and high-current return paths, and provide a clean ground reference to the analog pins. Although the device has a 20-bit ADC, the usable result depends on reference quality, source impedance, acquisition timing, and board noise. Use short traces, suitable grounding, and external filtering or buffering when the sensor source cannot drive the ADC network directly.
コンプライアンス情報
Compliance documents for the exact CY8C3866LTI-068 ordering code were not included in the available product information. Request the manufacturer material-declaration documents before making a compliance claim.