CY8C4125LQI-483 - 24MHz 32KB PSoC 4 MCU | Infineon
部品番号: CY8C4125LQI-483 ✓ 生産中CY8C4125LQI-483 概要
A PSoC microcontroller is a mixed-signal embedded-control device that combines a microcontroller core with programmable analog and digital peripherals. Within the semiconductor hierarchy, PSoC 4 belongs to the microcontroller and embedded-processor family, where it bridges general-purpose firmware execution with configurable signal acquisition, touch sensing, timers, communications, and control functions. This integration can reduce the number of discrete components required in compact sensing and control systems.
Principal features include 24 MHz maximum CPU operation, 32 KB flash, 4 KB SRAM, 34 GPIOs, a 12-bit SAR ADC at 806 ksps, and a dedicated CapSense block for touch-sensing applications. The digital fabric allows peripherals to be routed to GPIO pins according to application requirements, while the analog section supports acquisition and signal-conditioning functions near the sensor input.
The Arm Cortex-M0 architecture provides a compact instruction set and deterministic embedded-control behavior without the complexity of a higher-performance core. Four configurable 16-bit timer, counter, and PWM blocks support periodic measurement, motor or actuator timing, and general event management. Firmware is stored in the 32 KB program-memory region, while the 4 KB SRAM provides working space for stacks, variables, and intermediate processing.
Typical applications include capacitive touch controls, industrial sensor nodes, compact user-interface modules, building controls, wearable accessories, and low-cost embedded products requiring both analog measurement and digital connectivity. The 806 ksps ADC supports fast analog sampling, while the CapSense hardware can accelerate touch detection and reduce firmware overhead.
PCB implementation requires careful placement of decoupling capacitors and a continuous ground-plane reference for the exposed pad and high-speed digital signals. Power-supply sequencing, analog grounding, signal integrity, and thermal management should be evaluated under the worst operating conditions in the manufacturer application notes and device datasheet.
This page combines the device specifications, sourcing information, same-family drop-in alternatives, application guidance, and design considerations into a consolidated engineering resource for evaluating the CY8C4125LQI-483.
ドロップイン代替品: CY8C4125LQI-483 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CY8C4125LQI-483 (同一形状・フットプリント) — 相違点: ADC Resolution, Package.
CY8C4127LQI-483
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
CY8C4145LQI-483
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
CY8C4147LQI-483
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
CY8C4245LQI-483
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
CY8C4247LQI-483
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
CY8C4125LQI-483 最大定格&電気的特性
| Product Type | PSoC 4 programmable system-on-chip microcontroller |
| CPU Core | Arm Cortex-M0, 32-bit |
| Maximum CPU Frequency | 24 MHz |
| Program Memory | 32 KB flash |
| SRAM | 4 KB |
| General-Purpose I/O | 34 GPIO |
| ADC Resolution | 12 bit |
| ADC Type | Successive-approximation register (SAR) |
| ADC Conversion Rate | 806 ksps |
| Timer Counter and PWM Blocks | 4 configurable 16-bit blocks |
| Supply Voltage Options | 2.5 V, 3.3 V, or 5 V |
| パッケージ | 40-QFN, 6 mm x 6 mm |
| 実装タイプ | Surface mount |
| Touch-Sensing Support | Dedicated CapSense block |
| Programmable Peripheral Routing | Any GPIO to any digital or analog peripheral |
| Shipping Package | Tray |
CY8C4125LQI-483 tray ピン配置ガイド
CY8C4125LQI-483 (tray パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: CY8C4125LQI-483.
詳細は データシート をご参照ください。
主な用途
CY8C4125LQI-483 の用途: 6 件s: Capacitive Touch Control Panels, Industrial Sensor Nodes, Building and HVAC Controls, Wearable and Personal Electronics, Compact Data Acquisition Modules, Automated Equipment and HMI Modules.
Capacitive Touch Control Panels
The CY8C4125LQI-483 fits capacitive touch controls because its dedicated CapSense block can evaluate touch electrodes while the Arm Cortex-M0 core handles user-interface logic at up to 24 MHz. The 34 GPIOs provide connections for LEDs, haptic feedback, and other controls without requiring a separate host processor. Place the touch electrodes and sensing components away from switching-current paths, maintain the ground reference described in the manufacturer hardware guidance, and validate sensitivity across temperature, humidity, and enclosure materials.
おすすめ
Industrial Sensor Nodes
The 12-bit SAR ADC at 806 ksps makes the CY8C4125LQI-483 suitable for compact industrial sensor nodes that must acquire analog measurements and perform local processing. Its 32 KB flash accommodates control firmware, while 4 KB SRAM supports protocol handling, filtering, and status data. The 40-QFN 6 mm by 6 mm package saves board area, although exposed-pad heat spreading and analog grounding remain important. Confirm the ADC source impedance, acquisition time, and input range during schematic design.
おすすめ
Building and HVAC Controls
The CY8C4125LQI-483 can consolidate sensing, touch input, timers, and communications in a distributed building-control node. Its four configurable 16-bit timer, counter, and PWM blocks are useful for periodic sensing, actuator timing, and motor or valve control, while the programmable peripheral fabric helps match pins to the board layout. The 24 MHz core is adequate for supervisory logic, but control-loop latency and communication interrupt load should be profiled. Local decoupling and a continuous ground plane reduce digital noise on analog measurements.
おすすめ
Wearable and Personal Electronics
The compact 40-QFN package and mixed-signal integration make the CY8C4125LQI-483 useful in wearable accessories and personal electronic products combining capacitive controls, analog sensing, and low-rate communications. The Cortex-M0 core supports compact real-time logic without a large application processor, while 32 KB flash provides room for a focused firmware image. Power consumption depends on active peripherals and clock configuration, so select the lowest operating mode that preserves response time. Confirm board size, exposed-pad access, and antenna layout during mechanical design.
おすすめ
Compact Data Acquisition Modules
With a 12-bit SAR ADC capable of 806 ksps, the CY8C4125LQI-483 can form the core of a compact acquisition module that samples analog signals and performs initial filtering or classification. Its programmable GPIO fabric allows digital triggers, status indicators, and communication interfaces to be assigned around the analog inputs. Sampling throughput must be evaluated together with channel-switching overhead, firmware processing time, and the ADC acquisition network. Use short, quiet analog traces and provide decoupling close to the device pins.
おすすめ
Automated Equipment and HMI Modules
The CY8C4125LQI-483 supports compact human-machine interface modules that combine buttons or capacitive controls, status LEDs, analog monitoring, and machine-state logic. The 24 MHz Cortex-M0 processor is suitable for deterministic user-interface and supervisory tasks, and the programmable peripheral fabric simplifies routing around a constrained 40-QFN pinout. Four configurable 16-bit timer blocks can handle periodic UI updates or actuator timing. Validate update latency, ESD protection, and grounding to keep user input reliable in electrically noisy equipment.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CY8C4125LQI-483 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CY8C4127LQI-483 | CY8C4145LQI-483 | CY8C4245LQI-483 | CY8C4247LQI-483 | CY8C4147LQI-483 |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | 40-QFN (6x6) | 40-QFN (6x6) | 40-QFN (6x6) | 40-QFN (6x6) | 40-QFN (6x6) | 40-QFN (6x6) |
| CPU Core | 32-bit Arm Cortex-M0 | 32-bit Arm Cortex-M0 | 32-bit Arm Cortex-M0 | 32-bit Arm Cortex-M0 | 32-bit Arm Cortex-M0 | 32-bit Arm Cortex-M0 |
主な差別化要因
- Balanced 24 MHz performance and memory for focused embedded-control designs (vs CY8C4145LQI-483)
- Integrated high-speed analog conversion (vs CY8C4245LQI-483)
- Dedicated CapSense hardware with programmable peripheral routing (vs CY8C4247LQI-483)
設計ノート
Place the required bypass capacitors immediately beside the device power pins and connect the exposed pad to a low-impedance ground plane. The 40-QFN package has no bottom-side pins outside the thermal pad, so routing must use the manufacturer land pattern rather than a generic QFN footprint. Keep analog inputs away from switching nodes and maintain a quiet ground reference under the sensing circuitry.
Use the official 40-QFN pinout and land pattern without substituting pin assignments from another PSoC 4 density or performance grade. Confirm the device orientation, exposed-pad dimensions, solder-mask clearance, and paste pattern in the manufacturer package drawing. A footprint mismatch can shift every signal assignment even when the nominal package dimensions appear identical.
Validate startup, shutdown, brownout, and peripheral-state behavior across the required 2.5 V, 3.3 V, or 5 V operating condition. Do not assume that the CPU clock, ADC, and communication peripherals can all operate simultaneously at their maximum ratings. Use the manufacturer current tables to size the supply and verify that the exposed pad provides adequate thermal spreading.
A higher-frequency family member is not automatically a functional substitute for the CY8C4125LQI-483. Check the boot configuration, debug interface, GPIO mapping, ADC channels, clock tree, timer resources, and firmware target before replacing the device. In particular, confirm that unused pins have acceptable levels during reset and that no new peripheral instance conflicts with an existing board connection.
コンプライアンス情報
The manufacturer product page and distributor descriptions do not provide explicit compliance declarations for this exact MPN. The ordering code does not identify an automotive-qualified variant, so AEC-Q100 status is treated as not applicable rather than qualified.